From mboxrd@z Thu Jan 1 00:00:00 1970 From: julien.thierry@arm.com (Julien Thierry) Date: Wed, 17 Jan 2018 15:11:33 +0000 Subject: [PATCH v3 10/41] KVM: arm64: Move debug dirty flag calculation out of world switch In-Reply-To: <20180112120747.27999-11-christoffer.dall@linaro.org> References: <20180112120747.27999-1-christoffer.dall@linaro.org> <20180112120747.27999-11-christoffer.dall@linaro.org> Message-ID: To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org On 12/01/18 12:07, Christoffer Dall wrote: > There is no need to figure out inside the world-switch if we should > save/restore the debug registers or not, we can might as well do that in Nit: -can* > the higher level debug setup code, making it easier to optimize down the > line. > > Reviewed-by: Marc Zyngier > Signed-off-by: Christoffer Dall Reviewed-by: Julien Thierry > --- > arch/arm64/kvm/debug.c | 5 +++++ > arch/arm64/kvm/hyp/debug-sr.c | 6 ------ > 2 files changed, 5 insertions(+), 6 deletions(-) > > diff --git a/arch/arm64/kvm/debug.c b/arch/arm64/kvm/debug.c > index fa63b28c65e0..feedb877cff8 100644 > --- a/arch/arm64/kvm/debug.c > +++ b/arch/arm64/kvm/debug.c > @@ -193,6 +193,11 @@ void kvm_arm_setup_debug(struct kvm_vcpu *vcpu) > if (trap_debug) > vcpu->arch.mdcr_el2 |= MDCR_EL2_TDA; > > + /* If KDE or MDE are set, perform a full save/restore cycle. */ > + if ((vcpu_sys_reg(vcpu, MDSCR_EL1) & DBG_MDSCR_KDE) || > + (vcpu_sys_reg(vcpu, MDSCR_EL1) & DBG_MDSCR_MDE)) > + vcpu->arch.debug_flags |= KVM_ARM64_DEBUG_DIRTY; > + > trace_kvm_arm_set_dreg32("MDCR_EL2", vcpu->arch.mdcr_el2); > trace_kvm_arm_set_dreg32("MDSCR_EL1", vcpu_sys_reg(vcpu, MDSCR_EL1)); > } > diff --git a/arch/arm64/kvm/hyp/debug-sr.c b/arch/arm64/kvm/hyp/debug-sr.c > index 321c9c05dd9e..406829b6a43e 100644 > --- a/arch/arm64/kvm/hyp/debug-sr.c > +++ b/arch/arm64/kvm/hyp/debug-sr.c > @@ -162,12 +162,6 @@ void __hyp_text __debug_restore_state(struct kvm_vcpu *vcpu, > > void __hyp_text __debug_cond_save_host_state(struct kvm_vcpu *vcpu) > { > - /* If any of KDE, MDE or KVM_ARM64_DEBUG_DIRTY is set, perform > - * a full save/restore cycle. */ > - if ((vcpu->arch.ctxt.sys_regs[MDSCR_EL1] & DBG_MDSCR_KDE) || > - (vcpu->arch.ctxt.sys_regs[MDSCR_EL1] & DBG_MDSCR_MDE)) > - vcpu->arch.debug_flags |= KVM_ARM64_DEBUG_DIRTY; > - > __debug_save_state(vcpu, &vcpu->arch.host_debug_state.regs, > kern_hyp_va(vcpu->arch.host_cpu_context)); > __debug_save_spe()(&vcpu->arch.host_debug_state.pmscr_el1); > -- Julien Thierry