[PATCH v6 0/5] Support i.MX28 Amarula rmm board

[PATCH v6 0/5] Support i.MX28 Amarula rmm board

[Dario Binacchi]

The series adds support for i.MX28 Amarula rmm board.

The board includes the following resources:
 - 256 Mbytes NAND Flash
 - 128 Mbytes DRAM DDR2
 - CAN
 - USB 2.0 high-speed/full-speed
 - Ethernet MAC

Changes in v6:
- Drop [PATCH v5 1/6] "dt-bindings: mfd: convert mxs-lradc bindings
  to json-schema" because applied by Lee Jones.

Changes in v5:
- In mxs-lradc.txt:
  - Fix deacription formating
- In imx28-amarula-rmm.dts:
  - Drop #address-cells from gpmi node

Changes in v4:
- In mxs-lradc.txt:
  - Fix typo Low-Resoulution -> Low-Resolution'
  - Wrap lines at 80 char.
  - Drop '|' from the description
  - Describe what each interrupt is for.
  - Move touchscreen-wires constraint for imx28 to the top level
- In imx28-amarula-rmm.dts:
  - Drop label property (deprecated) under the leds sub-nodes.
  - Add microSD comment above the ssp0 node.
- Add patch 5/6 "ARM: mxs_defconfig: Cleanup mxs_defconfig"
- Add patch 6/6 "ARM: mxs_defconfig: select new drivers used by
  imx28-amarula-rmm"

Changes in v3:
- In imx28-amarula-rmm.dts:
  - Drop xceiver-supply property from can0 node.
  - Rearrange the order of specific nodes and properties
    alphabetically.

Changes in v2:
- In imx28-amarula-rmm.dts:
  - Replace '-' with '@' for the pinctrl sub-nodes.
  - Replace edt,edt-ft5x06 with edt,edt-ft5306.
  - Drop LCD reset hog pin.
  - Add correct #address-cells and #size-cells to gpmi node.
  - Replace edt-ft5x06@38 with touchscreen@38.
- Drop from commit messages all references to LCD display.
- Add patch [1/4] "dt-bindings: mfd: convert mxs-lradc bindings to
  json-schema".

Dario Binacchi (5):
  ARM: dts: imx28: add pwm7 muxing options
  dt-bindings: arm: fsl: add i.MX28 Amarula rmm board
  ARM: dts: mxs: support i.MX28 Amarula rmm board
  ARM: mxs_defconfig: Cleanup mxs_defconfig
  ARM: mxs_defconfig: select new drivers used by imx28-amarula-rmm

 .../devicetree/bindings/arm/fsl.yaml          |   1 +
 arch/arm/boot/dts/nxp/mxs/Makefile            |   1 +
 .../boot/dts/nxp/mxs/imx28-amarula-rmm.dts    | 300 ++++++++++++++++++
 arch/arm/boot/dts/nxp/mxs/imx28.dtsi          |  10 +
 arch/arm/configs/mxs_defconfig                |  14 +-
 5 files changed, 315 insertions(+), 11 deletions(-)
 create mode 100644 arch/arm/boot/dts/nxp/mxs/imx28-amarula-rmm.dts

-- 
2.43.0

base-commit: fb5103df1b24f6cf8bdb333b24bbdf45d4186b0e
branch: imx28-amarula-rmm

[PATCH v6 1/5] ARM: dts: imx28: add pwm7 muxing options

[Dario Binacchi]

Add alternative pinmuxing for pwm7.

Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>

---

(no changes since v5)

Changes in v5:
- Add Reviewed-by tag of Frank Li

Changes in v3:
- Add commit body

 arch/arm/boot/dts/nxp/mxs/imx28.dtsi | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/arm/boot/dts/nxp/mxs/imx28.dtsi b/arch/arm/boot/dts/nxp/mxs/imx28.dtsi
index bbea8b77386f..ece46d0e7c7f 100644
--- a/arch/arm/boot/dts/nxp/mxs/imx28.dtsi
+++ b/arch/arm/boot/dts/nxp/mxs/imx28.dtsi
@@ -755,6 +755,16 @@ MX28_PAD_PWM4__PWM_4
 					fsl,pull-up = <MXS_PULL_DISABLE>;
 				};
 
+				pwm7_pins_a: pwm7@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						MX28_PAD_SAIF1_SDATA0__PWM_7
+					>;
+					fsl,drive-strength = <MXS_DRIVE_4mA>;
+					fsl,voltage = <MXS_VOLTAGE_HIGH>;
+					fsl,pull-up = <MXS_PULL_DISABLE>;
+				};
+
 				lcdif_24bit_pins_a: lcdif-24bit@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
-- 
2.43.0

[PATCH v6 3/5] ARM: dts: mxs: support i.MX28 Amarula rmm board

[Dario Binacchi]

The board includes the following resources:
 - 256 Mbytes NAND Flash
 - 128 Mbytes DRAM DDR2
 - CAN
 - USB 2.0 high-speed/full-speed
 - Ethernet MAC

Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>

---

Changes in v6:
- Add Reviewed-by tag of Frank Li

Changes in v5:
- Drop #address-cells from gpmi node

Changes in v4:
- Drop label property (deprecated) under the leds sub-nodes.
- Add microSD comment above the ssp0 node.

Changes in v3:
- Drop xceiver-supply property from can0 node.
- Rearrange the order of specific nodes and properties
  alphabetically.

Changes in v2:
- Replace '-' with '@' for the pinctrl sub-nodes.
- Replace edt,edt-ft5x06 with edt,edt-ft5306.
- Drop LCD reset hog pin.
- Add correct #address-cells and #size-cells to gpmi node.
- Replace edt-ft5x06@38 with touchscreen@38.

 arch/arm/boot/dts/nxp/mxs/Makefile            |   1 +
 .../boot/dts/nxp/mxs/imx28-amarula-rmm.dts    | 300 ++++++++++++++++++
 2 files changed, 301 insertions(+)
 create mode 100644 arch/arm/boot/dts/nxp/mxs/imx28-amarula-rmm.dts

diff --git a/arch/arm/boot/dts/nxp/mxs/Makefile b/arch/arm/boot/dts/nxp/mxs/Makefile
index 96dd31ea19ba..d72ba702b6fa 100644
--- a/arch/arm/boot/dts/nxp/mxs/Makefile
+++ b/arch/arm/boot/dts/nxp/mxs/Makefile
@@ -5,6 +5,7 @@ dtb-$(CONFIG_ARCH_MXS) += \
 	imx23-sansa.dtb \
 	imx23-stmp378x_devb.dtb \
 	imx23-xfi3.dtb \
+	imx28-amarula-rmm.dtb \
 	imx28-apf28.dtb \
 	imx28-apf28dev.dtb \
 	imx28-apx4devkit.dtb \
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-amarula-rmm.dts b/arch/arm/boot/dts/nxp/mxs/imx28-amarula-rmm.dts
new file mode 100644
index 000000000000..af59211842fb
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-amarula-rmm.dts
@@ -0,0 +1,300 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2025 Amarula Solutions, Dario Binacchi <dario.binacchi@amarulasolutions.com>
+ */
+
+/dts-v1/;
+
+#include "imx28.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "amarula,imx28-rmm", "fsl,imx28";
+	model = "Amarula i.MX28 rmm";
+
+	memory@40000000 {
+		reg = <0x40000000 0x08000000>;
+		device_type = "memory";
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 4 5000000 0>;
+		brightness-levels = <0 255>;
+		num-interpolated-steps = <255>;
+		default-brightness-level = <255>;
+		power-supply = <&reg_5v>;
+	};
+
+	beeper {
+		compatible = "pwm-beeper";
+		pwms = <&pwm 7 100000 0>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&leds_pins>;
+
+		led-0 {
+			gpios = <&gpio2 7 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-1 {
+			gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-2 {
+			gpios = <&gpio3 17 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	reg_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	reg_fec_3v3: regulator-fec-3v3 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&fec_3v3_enable_pin>;
+		regulator-name = "fec-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <300000>;
+		vin-supply = <&reg_5v>;
+	};
+
+	reg_usb0_vbus: regulator-usb0-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb0_vbus_enable_pin>;
+		regulator-name = "usb0_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio2 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reg_usb1_vbus: regulator-usb1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb1_vbus_enable_pin>;
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio2 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+};
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_2pins_a>;
+	status = "okay";
+};
+
+&auart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart1_pins_a>;
+	status = "okay";
+};
+
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&can0_pins_a>;
+	status = "okay";
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_b>;
+	status = "okay";
+};
+
+&duart_pins_b {
+	fsl,voltage = <MXS_VOLTAGE_LOW>;
+};
+
+&gpmi {
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	touchscreen: touchscreen@38 {
+		compatible = "edt,edt-ft5306";
+		reg = <0x38>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&edt_ft5x06_pins &edt_ft5x06_wake_pin>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <19 IRQ_TYPE_EDGE_RISING>;
+		reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
+		wake-gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&lradc {
+	status = "okay";
+};
+
+&mac0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	phy-mode = "rmii";
+	phy-supply = <&reg_fec_3v3>;
+	phy-handle = <&ethphy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			max-speed = <100>;
+			reset-gpios = <&gpio3 28 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <4000>;
+			reset-deassert-us = <4000>;
+		};
+	};
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>;
+
+	edt_ft5x06_pins: edt-ft5x06@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_RDY1__GPIO_0_21 /* Reset */
+			MX28_PAD_GPMI_CE3N__GPIO_0_19 /* Interrupt */
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+	};
+
+	edt_ft5x06_wake_pin: edt-ft5x06-wake@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <MX28_PAD_GPMI_CE2N__GPIO_0_18>;
+		fsl,drive-strength = <MXS_DRIVE_16mA>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+	};
+
+	fec_3v3_enable_pin: fec-3v3-enable@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <MX28_PAD_SPDIF__GPIO_3_27>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+	};
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP2_SS1__GPIO_2_20  /* External power */
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+	};
+
+	leds_pins: leds@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP0_DATA7__GPIO_2_7
+			MX28_PAD_PWM0__GPIO_3_16
+			MX28_PAD_PWM1__GPIO_3_17
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+	};
+
+	usb0_vbus_enable_pin: usb0-vbus-enable@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <MX28_PAD_SSP0_DATA5__GPIO_2_5>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+	};
+
+	usb1_vbus_enable_pin: usb1-vbus-enable@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <MX28_PAD_SSP0_DATA6__GPIO_2_6>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm4_pins_a &pwm7_pins_a>;
+	status = "okay";
+};
+
+/* microSD */
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_sck_cfg>;
+	broken-cd;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&usb0 {
+	dr_mode = "host";
+	vbus-supply = <&reg_usb0_vbus>;
+	status = "okay";
+};
+
+&usb1 {
+	dr_mode = "host";
+	vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+};
+
+&usbphy0 {
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
-- 
2.43.0

[PATCH v6 4/5] ARM: mxs_defconfig: Cleanup mxs_defconfig

[Dario Binacchi]

Generate mxs_defconfig by doing:

make mxs_defconfig
make savedefconfig
cp defconfig arch/arm/configs/mxs_defconfig

No functional change. The goal here is to cleanup mxs_defconfig file to
make easier and cleaner the addition of new entries.

Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
---

(no changes since v1)

 arch/arm/configs/mxs_defconfig | 11 -----------
 1 file changed, 11 deletions(-)

diff --git a/arch/arm/configs/mxs_defconfig b/arch/arm/configs/mxs_defconfig
index c76d66135abb..91723fdd3c04 100644
--- a/arch/arm/configs/mxs_defconfig
+++ b/arch/arm/configs/mxs_defconfig
@@ -32,9 +32,6 @@ CONFIG_INET=y
 CONFIG_IP_PNP=y
 CONFIG_IP_PNP_DHCP=y
 CONFIG_SYN_COOKIES=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
 # CONFIG_INET_DIAG is not set
 # CONFIG_IPV6 is not set
 CONFIG_CAN=m
@@ -45,7 +42,6 @@ CONFIG_MTD=y
 CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_BLOCK=y
 CONFIG_MTD_DATAFLASH=y
-CONFIG_MTD_M25P80=y
 CONFIG_MTD_SST25L=y
 CONFIG_MTD_RAW_NAND=y
 CONFIG_MTD_NAND_GPMI_NAND=y
@@ -60,7 +56,6 @@ CONFIG_ENC28J60=y
 CONFIG_ICPLUS_PHY=y
 CONFIG_MICREL_PHY=y
 CONFIG_REALTEK_PHY=y
-CONFIG_SMSC_PHY=y
 CONFIG_CAN_FLEXCAN=m
 CONFIG_USB_USBNET=y
 CONFIG_USB_NET_SMSC95XX=y
@@ -77,13 +72,11 @@ CONFIG_SERIAL_AMBA_PL011=y
 CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
 CONFIG_SERIAL_MXS_AUART=y
 # CONFIG_HW_RANDOM is not set
-# CONFIG_I2C_COMPAT is not set
 CONFIG_I2C_CHARDEV=y
 CONFIG_I2C_MXS=y
 CONFIG_SPI=y
 CONFIG_SPI_GPIO=m
 CONFIG_SPI_MXS=y
-CONFIG_GPIO_SYSFS=y
 # CONFIG_HWMON is not set
 CONFIG_WATCHDOG=y
 CONFIG_STMP3XXX_RTC_WATCHDOG=y
@@ -138,10 +131,6 @@ CONFIG_PWM_MXS=y
 CONFIG_NVMEM_MXS_OCOTP=y
 CONFIG_EXT4_FS=y
 # CONFIG_DNOTIFY is not set
-CONFIG_NETFS_SUPPORT=m
-CONFIG_FSCACHE=y
-CONFIG_FSCACHE_STATS=y
-CONFIG_CACHEFILES=m
 CONFIG_VFAT_FS=y
 CONFIG_TMPFS=y
 CONFIG_TMPFS_POSIX_ACL=y
-- 
2.43.0

[PATCH v6 5/5] ARM: mxs_defconfig: select new drivers used by imx28-amarula-rmm

[Dario Binacchi]

Select the options required by the imx28-amarula-rmm board.

Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>

---

Changes in v6:
- Drop [PATCH v5 1/6] "dt-bindings: mfd: convert mxs-lradc bindings
  to json-schema" because applied by Lee Jones.

Changes in v5:
- In mxs-lradc.txt:
  - Fix deacription formating
- In imx28-amarula-rmm.dts:
  - Drop #address-cells from gpmi node

Changes in v4:
- In mxs-lradc.txt:
  - Fix typo Low-Resoulution -> Low-Resolution'
  - Wrap lines at 80 char.
  - Drop '|' from the description
  - Describe what each interrupt is for.
  - Move touchscreen-wires constraint for imx28 to the top level
- In imx28-amarula-rmm.dts:
  - Drop label property (deprecated) under the leds sub-nodes.
  - Add microSD comment above the ssp0 node.
- Add patch 5/6 "ARM: mxs_defconfig: Cleanup mxs_defconfig"
- Add patch 6/6 "ARM: mxs_defconfig: select new drivers used by
  imx28-amarula-rmm"

Changes in v3:
- In imx28-amarula-rmm.dts:
  - Drop xceiver-supply property from can0 node.
  - Rearrange the order of specific nodes and properties
    alphabetically.

Changes in v2:
- In imx28-amarula-rmm.dts:
  - Replace '-' with '@' for the pinctrl sub-nodes.
  - Replace edt,edt-ft5x06 with edt,edt-ft5306.
  - Drop LCD reset hog pin.
  - Add correct #address-cells and #size-cells to gpmi node.
  - Replace edt-ft5x06@38 with touchscreen@38.
- Drop from commit messages all references to LCD display.
- Add patch [1/4] "dt-bindings: mfd: convert mxs-lradc bindings to
  json-schema".

 arch/arm/configs/mxs_defconfig | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/configs/mxs_defconfig b/arch/arm/configs/mxs_defconfig
index 91723fdd3c04..3b08c63b6de4 100644
--- a/arch/arm/configs/mxs_defconfig
+++ b/arch/arm/configs/mxs_defconfig
@@ -64,8 +64,11 @@ CONFIG_INPUT_EVDEV=y
 # CONFIG_INPUT_KEYBOARD is not set
 # CONFIG_INPUT_MOUSE is not set
 CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_EDT_FT5X06=y
 CONFIG_TOUCHSCREEN_MXS_LRADC=y
 CONFIG_TOUCHSCREEN_TSC2007=m
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_PWM_BEEPER=y
 # CONFIG_SERIO is not set
 # CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_AMBA_PL011=y
-- 
2.43.0

Re: [PATCH v6 0/5] Support i.MX28 Amarula rmm board

[Shawn Guo]

On Fri, Jun 20, 2025 at 10:06:16AM +0200, Dario Binacchi wrote:
> Dario Binacchi (5):
>   ARM: dts: imx28: add pwm7 muxing options
>   dt-bindings: arm: fsl: add i.MX28 Amarula rmm board
>   ARM: dts: mxs: support i.MX28 Amarula rmm board
>   ARM: mxs_defconfig: Cleanup mxs_defconfig
>   ARM: mxs_defconfig: select new drivers used by imx28-amarula-rmm

Applied all, thanks!