[PATCH v4 1/2] dt-bindings: arm: add TQMLS1012AL

[PATCH v4 1/2] dt-bindings: arm: add TQMLS1012AL

[Alexander Stein]

From: Matthias Schiffer <matthias.schiffer@tq-group.com>

TQMLS1012AL is a SOM using NXP LS1012A CPU. MBLS1012AL is a carrier
reference design.

[1] https://www.tq-group.com/en/products/tq-embedded/qoriq-layerscape/tqmls1012al

Signed-off-by: Matthias Schiffer <matthias.schiffer@tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
---
Changes in v3:
* Fixed commit message subject

Changes in v3:
* None

Changes in v2:
* Collected Conor's A-b

 Documentation/devicetree/bindings/arm/fsl.yaml | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index f494ada0c1966..0beb0040a7d34 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -1571,6 +1571,12 @@ properties:
               - fsl,ls1012a-qds
           - const: fsl,ls1012a
 
+      - description: TQ Systems TQMLS12AL SoM on MBLS1012AL board
+        items:
+          - const: tq,ls1012a-tqmls1012al-mbls1012al
+          - const: tq,ls1012a-tqmls1012al
+          - const: fsl,ls1012a
+
       - description: LS1021A based Boards
         items:
           - enum:
-- 
2.43.0

[PATCH v4 2/2] arm64: dts: ls1012a: add DTS for TQMLS1012al module with MBLS1012AL board

[Alexander Stein]

From: Matthias Schiffer <matthias.schiffer@tq-group.com>

Add initial support for TQMLS1012AL module mounted on MBLS1012AL.
It supports UART1 for console, PCIe, I2C, USB, µSD card (default), SATA
and QSPI.
There is an alternative ordering option which provides an eMMC instead of
an SD card. This uses a different DT instead.
Due missing Packet Forwarding Engine (PFE) driver support, there is no
support for Ethernet so far.

Signed-off-by: Max Merchel <Max.Merchel@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
Changes in v4:
* Added regulator-boot-on for Mini-PCIe slot supplies

Changes in v3:
* Sorted i2c nodes according their address
* Delete SD card specific properties from eMMC configuration
* Remove duplicated properties
* Sorted alias entries alphabetically
* Add 1.8V vcc supply for SPINOR flash
* Implement PCIE and WLAN power supplies as regulator, both 1.8V and 3.3V
* Rename regulators accordingly to the power rail signal name
* Renamed GPIO expander node names (gpio@)

Changes in v2:
* Be a bit more specific with lm75 compatible
* Remove m25p,fast-read from spi-nor flash

 arch/arm64/boot/dts/freescale/Makefile        |   2 +
 ...sl-ls1012a-tqmls1012al-mbls1012al-emmc.dts |  23 ++
 .../fsl-ls1012a-tqmls1012al-mbls1012al.dts    | 366 ++++++++++++++++++
 .../freescale/fsl-ls1012a-tqmls1012al.dtsi    |  81 ++++
 4 files changed, 472 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1012a-tqmls1012al-mbls1012al-emmc.dts
 create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1012a-tqmls1012al-mbls1012al.dts
 create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1012a-tqmls1012al.dtsi

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 8b1bda0afb676..6fcddaf761ff8 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -5,6 +5,8 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-frwy.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-oxalis.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-qds.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-tqmls1012al-mbls1012al.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-tqmls1012al-mbls1012al-emmc.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-kontron-kbox-a-230-ls.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-kontron-sl28.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-kontron-sl28-var1.dtb
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-tqmls1012al-mbls1012al-emmc.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-tqmls1012al-mbls1012al-emmc.dts
new file mode 100644
index 0000000000000..07026b067320f
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-tqmls1012al-mbls1012al-emmc.dts
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright (c) 2018-2025 TQ-Systems GmbH <linux@ew.tq-group.com>,
+ * D-82229 Seefeld, Germany.
+ * Author: Matthias Schiffer
+ * Author: Max Merchel
+ */
+
+#include "fsl-ls1012a-tqmls1012al-mbls1012al.dts"
+
+&esdhc0 {
+	vqmmc-supply = <&reg_1v8>;
+	/delete-property/ no-mmc;
+	/delete-property/ sd-uhs-sdr12;
+	/delete-property/ sd-uhs-sdr25;
+	/delete-property/ sd-uhs-sdr50;
+	/delete-property/ sd-uhs-sdr104;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	no-sd;
+	voltage-ranges = <1800 1800>;
+	non-removable;
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-tqmls1012al-mbls1012al.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-tqmls1012al-mbls1012al.dts
new file mode 100644
index 0000000000000..e46cc1a07f0ca
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-tqmls1012al-mbls1012al.dts
@@ -0,0 +1,366 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright (c) 2018-2025 TQ-Systems GmbH <linux@ew.tq-group.com>,
+ * D-82229 Seefeld, Germany.
+ * Author: Matthias Schiffer
+ * Author: Max Merchel
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include "fsl-ls1012a-tqmls1012al.dtsi"
+
+/ {
+	model = "TQ-Systems TQMLS1012AL on MBLS1012AL";
+	compatible = "tq,ls1012a-tqmls1012al-mbls1012al", "tq,ls1012a-tqmls1012al", "fsl,ls1012a";
+	chassis-type = "embedded";
+
+	aliases {
+		/* use MAC from U-Boot environment */
+		/* TODO: PFE */
+		ethernet2 = &swport0;
+		ethernet3 = &swport1;
+		ethernet4 = &swport2;
+		ethernet5 = &swport3;
+		serial0 = &duart0;
+		spi0 = &qspi;
+	};
+
+	chosen {
+		stdout-path = &duart0;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		switch-1 {
+			label = "S2";
+			linux,code = <BTN_0>;
+			gpios = <&gpio_exp_3p3v 13 GPIO_ACTIVE_LOW>;
+		};
+
+		switch-2 {
+			label = "X15";
+			linux,code = <BTN_1>;
+			gpios = <&gpio_exp_1p8v 5 GPIO_ACTIVE_LOW>;
+		};
+
+		switch-3 {
+			label = "X16";
+			linux,code = <BTN_2>;
+			gpios = <&gpio_exp_1p8v 4 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_HEARTBEAT;
+			gpios = <&gpio_exp_3p3v 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio_exp_3p3v 15 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* global autoconfigured region for contiguous allocations */
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			/* 64 MiB */
+			size = <0 0x04000000>;
+			/*  512 - 128 MiB, our minimum RAM config will be 512 MiB */
+			alloc-ranges = <0 0x80000000 0 0x98000000>;
+			linux,cma-default;
+		};
+	};
+
+	reg_1v5: regulator-1v5 {
+		compatible = "regulator-fixed";
+		regulator-name = "V_1V5";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+	};
+
+	reg_1p5v_pcie: regulator-1p5v-pcie {
+		compatible = "regulator-fixed";
+		regulator-name = "V_1V5_PCIE";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio_exp_1p8v 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&reg_1v5>;
+	};
+
+	reg_1p5v_wlan: regulator-1p5v-wlan {
+		compatible = "regulator-fixed";
+		regulator-name = "V_1V5_WLAN";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio_exp_1p8v 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&reg_1v5>;
+	};
+
+	reg_1v8: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "V_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	reg_3v3: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_3v3_pcie: regulator-3v3-pcie {
+		compatible = "regulator-fixed";
+		regulator-name = "V_3V3_PCIE";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio_exp_3p3v 3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&reg_3v3>;
+	};
+
+	reg_3v3_wlan: regulator-3v3-wlan {
+		compatible = "regulator-fixed";
+		regulator-name = "V_3V3_WLAN";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio_exp_3p3v 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&reg_3v3>;
+	};
+};
+
+&duart0 {
+	status = "okay";
+};
+
+&esdhc0 {
+	vmmc-supply = <&reg_3v3>;
+	no-mmc;
+	no-sdio;
+	disable-wp;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	status = "okay";
+};
+
+&i2c0 {
+	gpio_exp_3p3v: gpio@20 {
+		compatible = "nxp,pca9555";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		vcc-supply = <&reg_3v3>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-line-names = "", "", "GPIO_3V3_3", "",
+				  "", "", "", "",
+				  "", "GPIO_3V3_1", "GPIO_3V3_2", "",
+				  "", "", "", "";
+
+		wlan-disable-hog {
+			gpio-hog;
+			gpios = <0 GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "WLAN_DISABLE#";
+		};
+
+		pcie-rst-hog {
+			gpio-hog;
+			gpios = <4 GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "PCIE_RST#";
+		};
+
+		wlan-rst-hog {
+			gpio-hog;
+			gpios = <5 GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "WLAN_RST#";
+		};
+
+		pcie-dis-hog {
+			gpio-hog;
+			gpios = <11 GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "PCIE_DIS#";
+		};
+
+		pcie-wake-hog {
+			gpio-hog;
+			gpios = <12 GPIO_ACTIVE_HIGH>;
+			input;
+			line-name = "PCIE_WAKE#";
+		};
+	};
+
+	lm75_48: temperature-sensor@48 {
+		compatible = "national,lm75a";
+		reg = <0x48>;
+		vs-supply = <&reg_3v3>;
+	};
+
+	switch@5f {
+		compatible = "microchip,ksz9897";
+		reg = <0x5f>;
+		reset-gpios = <&gpio_exp_3p3v 7 GPIO_ACTIVE_LOW>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			swport0: port@0 {
+				reg = <0>;
+				label = "swp0";
+				phy-mode = "internal";
+			};
+
+			swport1: port@1 {
+				reg = <1>;
+				label = "swp1";
+				phy-mode = "internal";
+			};
+
+			swport2: port@2 {
+				reg = <2>;
+				label = "swp2";
+				phy-mode = "internal";
+			};
+
+			swport3: port@3 {
+				reg = <3>;
+				label = "swp3";
+				phy-mode = "internal";
+			};
+
+			port@6 {
+				reg = <6>;
+				label = "cpu";
+				/* TODO: PFE */
+				phy-mode = "rgmii-id";
+				rx-internal-delay-ps = <1500>;
+				tx-internal-delay-ps = <1500>;
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+		};
+	};
+
+	gpio_exp_1p8v: gpio@70 {
+		compatible = "nxp,pca9538";
+		reg = <0x70>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		vcc-supply = <&reg_1v8>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <27 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-line-names = "PCIE_CLK_PD#", "PMIC_INT#", "ETH_SW_INT#", "",
+				  "", "", "", "",
+				  "", "GPIO_3V3_1", "GPIO_3V3_2", "",
+				  "", "", "", "";
+
+		/* do not change PCIE_CLK_PD */
+		pcie-clk-pd-hog {
+			gpio-hog;
+			gpios = <0 GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "PCIE_CLK_PD#";
+		};
+
+		pmic-int-hog {
+			gpio-hog;
+			gpios = <1 GPIO_ACTIVE_HIGH>;
+			input;
+			line-name = "PMIC_INT#";
+		};
+
+		eth-sw-int-hog {
+			gpio-hog;
+			gpios = <2 GPIO_ACTIVE_HIGH>;
+			input;
+			line-name = "ETH_SW_INT#";
+		};
+
+		eth-link-pwrdwn-hog {
+			gpio-hog;
+			gpios = <3 GPIO_ACTIVE_HIGH>;
+			input;
+			line-name = "ETH_LINK_PWRDWN#";
+		};
+	};
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+/* TODO: PFE */
+
+&sata {
+	status = "okay";
+};
+
+&usb0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	hub_2_0: hub@1 {
+		compatible = "usb451,8142";
+		reg = <1>;
+		peer-hub = <&hub_3_0>;
+		reset-gpios = <&gpio_exp_3p3v 6 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&reg_vcc_3v3>;
+	};
+
+	hub_3_0: hub@2 {
+		compatible = "usb451,8140";
+		reg = <2>;
+		peer-hub = <&hub_2_0>;
+		reset-gpios = <&gpio_exp_3p3v 6 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&reg_vcc_3v3>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-tqmls1012al.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1012a-tqmls1012al.dtsi
new file mode 100644
index 0000000000000..7c5a3dee91b98
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-tqmls1012al.dtsi
@@ -0,0 +1,81 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright (c) 2018-2025 TQ-Systems GmbH <linux@ew.tq-group.com>,
+ * D-82229 Seefeld, Germany.
+ * Author: Matthias Schiffer
+ * Author: Max Merchel
+ */
+
+#include "fsl-ls1012a.dtsi"
+
+/ {
+	compatible = "tq,ls1012a-tqmls1012al", "fsl,ls1012a";
+
+	memory@80000000 {
+		device_type = "memory";
+		/*  our minimum RAM config will be 512 MiB */
+		reg = <0x00000000 0x80000000 0 0x20000000>;
+	};
+
+	reg_vcc_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_vcc_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	jc42_19: temperature-sensor@19 {
+		compatible = "nxp,se97b", "jedec,jc-42.4-temp";
+		reg = <0x19>;
+	};
+
+	m24c64_50: eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+		vcc-supply = <&reg_vcc_3v3>;
+	};
+
+	m24c02_51: eeprom@51 {
+		compatible = "nxp,se97b", "atmel,24c02";
+		reg = <0x51>;
+		pagesize = <16>;
+		read-only;
+		vcc-supply = <&reg_vcc_3v3>;
+	};
+
+	rtc1: rtc@68 {
+		compatible = "dallas,ds1339";
+		reg = <0x68>;
+	};
+};
+
+&qspi {
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <39000000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
+		vcc-supply = <&reg_vcc_1v8>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+		};
+	};
+};
-- 
2.43.0

Re: [PATCH v4 1/2] dt-bindings: arm: add TQMLS1012AL

[Rob Herring]

On Fri, Jul 25, 2025 at 08:24:50AM +0200, Alexander Stein wrote:
> From: Matthias Schiffer <matthias.schiffer@tq-group.com>
> 

The subject could use a 'fsl: '.

> TQMLS1012AL is a SOM using NXP LS1012A CPU. MBLS1012AL is a carrier
> reference design.
> 
> [1] https://www.tq-group.com/en/products/tq-embedded/qoriq-layerscape/tqmls1012al
> 
> Signed-off-by: Matthias Schiffer <matthias.schiffer@tq-group.com>
> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
> Acked-by: Conor Dooley <conor.dooley@microchip.com>
> ---
> Changes in v3:
> * Fixed commit message subject
> 
> Changes in v3:
> * None
> 
> Changes in v2:
> * Collected Conor's A-b
> 
>  Documentation/devicetree/bindings/arm/fsl.yaml | 6 ++++++
>  1 file changed, 6 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
> index f494ada0c1966..0beb0040a7d34 100644
> --- a/Documentation/devicetree/bindings/arm/fsl.yaml
> +++ b/Documentation/devicetree/bindings/arm/fsl.yaml
> @@ -1571,6 +1571,12 @@ properties:
>                - fsl,ls1012a-qds
>            - const: fsl,ls1012a
>  
> +      - description: TQ Systems TQMLS12AL SoM on MBLS1012AL board
> +        items:
> +          - const: tq,ls1012a-tqmls1012al-mbls1012al
> +          - const: tq,ls1012a-tqmls1012al
> +          - const: fsl,ls1012a
> +
>        - description: LS1021A based Boards
>          items:
>            - enum:
> -- 
> 2.43.0
> 

Re: [PATCH v4 1/2] dt-bindings: arm: add TQMLS1012AL

[Shawn Guo]

On Fri, Jul 25, 2025 at 02:56:28PM -0500, Rob Herring wrote:
> On Fri, Jul 25, 2025 at 08:24:50AM +0200, Alexander Stein wrote:
> > From: Matthias Schiffer <matthias.schiffer@tq-group.com>
> > 
> 
> The subject could use a 'fsl: '.

Fixed it up, and applied both.