Re: [PATCH v2 4/5] arm64: dts: imx8mp-evk: Use phys to replace xceiver-supply

[Frank Li <Frank.li@nxp.com>]

On Mon, Aug 25, 2025 at 04:36:45PM +0800, Peng Fan wrote:
> The TJA1048 used on i.MX8MP-EVK is actually high-speed CAN
> transceiver, not a regulator supply. So use phys to reflect the truth.

nit: wrap at 75 chars. 'transceiver', should be at first line.

Reviewed-by: Frank Li <Frank.Li@nxp.com>

>
> Signed-off-by: Peng Fan <peng.fan@nxp.com>
> ---
>  arch/arm64/boot/dts/freescale/imx8mp-evk.dts | 43 +++++++++-------------------
>  1 file changed, 13 insertions(+), 30 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
> index c0cc5611048e6a739f13c14bbd2e7b26f2715696..d238d419d87cc7c99d472720c96aade90275cb0f 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
> @@ -56,6 +56,16 @@ memory@40000000 {
>  		      <0x1 0x00000000 0 0xc0000000>;
>  	};
>
> +	flexcan_phy: can-phy {
> +		compatible = "nxp,tja1048";
> +		#phy-cells = <1>;
> +		max-bitrate = <5000000>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_flexcan_phy>;
> +		standby-gpios = <&gpio5 5 GPIO_ACTIVE_LOW>,
> +				<&gpio4 27 GPIO_ACTIVE_LOW>;
> +	};
> +
>  	native-hdmi-connector {
>  		compatible = "hdmi-connector";
>  		label = "HDMI OUT";
> @@ -103,28 +113,6 @@ reg_audio_pwr: regulator-audio-pwr {
>  		enable-active-high;
>  	};
>
> -	reg_can1_stby: regulator-can1-stby {
> -		compatible = "regulator-fixed";
> -		regulator-name = "can1-stby";
> -		pinctrl-names = "default";
> -		pinctrl-0 = <&pinctrl_flexcan1_reg>;
> -		regulator-min-microvolt = <3300000>;
> -		regulator-max-microvolt = <3300000>;
> -		gpio = <&gpio5 5 GPIO_ACTIVE_HIGH>;
> -		enable-active-high;
> -	};
> -
> -	reg_can2_stby: regulator-can2-stby {
> -		compatible = "regulator-fixed";
> -		regulator-name = "can2-stby";
> -		pinctrl-names = "default";
> -		pinctrl-0 = <&pinctrl_flexcan2_reg>;
> -		regulator-min-microvolt = <3300000>;
> -		regulator-max-microvolt = <3300000>;
> -		gpio = <&gpio4 27 GPIO_ACTIVE_HIGH>;
> -		enable-active-high;
> -	};
> -
>  	reg_pcie0: regulator-pcie {
>  		compatible = "regulator-fixed";
>  		pinctrl-names = "default";
> @@ -431,14 +419,14 @@ ethphy1: ethernet-phy@1 {
>  &flexcan1 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&pinctrl_flexcan1>;
> -	xceiver-supply = <&reg_can1_stby>;
> +	phys = <&flexcan_phy 0>;
>  	status = "okay";
>  };
>
>  &flexcan2 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&pinctrl_flexcan2>;
> -	xceiver-supply = <&reg_can2_stby>;
> +	phys = <&flexcan_phy 1>;
>  	status = "disabled";/* can2 pin conflict with pdm */
>  };
>
> @@ -903,14 +891,9 @@ MX8MP_IOMUXC_SAI5_RXD3__CAN2_TX         0x154
>  		>;
>  	};
>
> -	pinctrl_flexcan1_reg: flexcan1reggrp {
> +	pinctrl_flexcan_phy: flexcanphygrp {
>  		fsl,pins = <
>  			MX8MP_IOMUXC_SPDIF_EXT_CLK__GPIO5_IO05  0x154   /* CAN1_STBY */
> -		>;
> -	};
> -
> -	pinctrl_flexcan2_reg: flexcan2reggrp {
> -		fsl,pins = <
>  			MX8MP_IOMUXC_SAI2_MCLK__GPIO4_IO27      0x154   /* CAN2_STBY */
>  		>;
>  	};
>
> --
> 2.37.1
>