[PATCH v3 0/6] arm64: dts: imx8mm-phyboard-polis: cleanup and additional display

[PATCH v3 0/6] arm64: dts: imx8mm-phyboard-polis: cleanup and additional display

[Jan Remmet]

This patch stacks rework the handling of the peb-av-10 daughterboard.
Update license.
Move mipi bridge configuration to som.
Allow peb-av-10 as audio only overlay.
Add two display overlays for ETML1010G3DRA and PH128800T00.

Signed-off-by: Jan Remmet <j.remmet@phytec.de>
---
Changes in v3:
- rebased onto shawnguo/for-next
- add Acked-by
- Link to v2: https://lore.kernel.org/r/20251007-wip-j-remmet-phytec-de-bspimx8m-3801_peb-av-10_with_ac209-v2-0-7e5de62c79bf@phytec.de

Changes in v2:
- add Signed-off-by to patch6
- Link to v1: https://lore.kernel.org/r/20250930-wip-j-remmet-phytec-de-bspimx8m-3801_peb-av-10_with_ac209-v1-0-d5d03ccbfca1@phytec.de

---
Jan Remmet (5):
      arm64: dts: imx8mm-phyboard-polis: Use GPL-2.0-or-later OR MIT
      arm64: dts: imx8mm-phyboard-polis: move mipi bridge to som
      arm64: dts: imx8mm-phyboard-polis-peb-av-10: reorder properties to match dts coding style
      arm64: dts: imx8mm-phyboard-polis-peb-av-10: split display configuration
      arm64: dts: imx8mm-phyboard-polis-peb-av-10-ph128800t006

Teresa Remmet (1):
      arm64: dts: imx8mm-phyboard-polis-peb-av-10: Fix audio codec reset pin ctl

 arch/arm64/boot/dts/freescale/Makefile             |   6 +
 ...8mm-phyboard-polis-peb-av-10-etml1010g3dra.dtso |  44 ++++
 ...x8mm-phyboard-polis-peb-av-10-ph128800t006.dtso |  44 ++++
 .../freescale/imx8mm-phyboard-polis-peb-av-10.dtsi | 189 +++++++++++++++++
 .../freescale/imx8mm-phyboard-polis-peb-av-10.dtso | 234 +--------------------
 .../imx8mm-phyboard-polis-peb-eval-01.dtso         |   3 +-
 .../dts/freescale/imx8mm-phyboard-polis-rdk.dts    |   3 +-
 .../boot/dts/freescale/imx8mm-phycore-som.dtsi     |  28 ++-
 8 files changed, 313 insertions(+), 238 deletions(-)
---
base-commit: b61938e8910c5dc0eecaf319ff12d67a35e39d9f
change-id: 20250925-wip-j-remmet-phytec-de-bspimx8m-3801_peb-av-10_with_ac209-ef10812a2d8d

Best regards,
-- 
Jan Remmet <j.remmet@phytec.de>

[PATCH v3 1/6] arm64: dts: imx8mm-phyboard-polis: Use GPL-2.0-or-later OR MIT

[Jan Remmet]

Update license and remove individual authorship.

Signed-off-by: Jan Remmet <j.remmet@phytec.de>
Acked-by: Teresa Remmet <t.remmet@phytec.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtso   | 3 +--
 arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-eval-01.dtso | 3 +--
 arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-rdk.dts          | 3 +--
 arch/arm64/boot/dts/freescale/imx8mm-phycore-som.dtsi                | 3 +--
 4 files changed, 4 insertions(+), 8 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtso b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtso
index 79e4c3710ac3f44ca88db9a6059cce986bf1fc3a..00da1eedf73aac1f0e87383ac3d12f21e007c4cc 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtso
+++ b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtso
@@ -1,7 +1,6 @@
-// SPDX-License-Identifier: GPL-2.0
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
 /*
  * Copyright (C) 2025 PHYTEC Messtechnik GmbH
- * Author: Teresa Remmet <t.remmet@phytec.de>
  */
 
 /dts-v1/;
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-eval-01.dtso b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-eval-01.dtso
index a28f51ece93ba62a7a9991826cca2ec74f704ba2..1059c26990fe6eb0d7acdad4d3386944f46ea99b 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-eval-01.dtso
+++ b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-eval-01.dtso
@@ -1,7 +1,6 @@
-// SPDX-License-Identifier: GPL-2.0
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
 /*
  * Copyright (C) 2025 PHYTEC Messtechnik GmbH
- * Author: Janine Hagemann <j.hagemann@phytec.de>
  */
 
 /dts-v1/;
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-rdk.dts b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-rdk.dts
index 35d8c5ab35472320b6657744c9f7965acab99f49..6043e7d163069398e10fec6dd7842a4fa58552ee 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-rdk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-rdk.dts
@@ -1,7 +1,6 @@
-// SPDX-License-Identifier: GPL-2.0
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
 /*
  * Copyright (C) 2022 PHYTEC Messtechnik GmbH
- * Author: Teresa Remmet <t.remmet@phytec.de>
  */
 
 /dts-v1/;
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-phycore-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-phycore-som.dtsi
index 921a7f58fd41da0967c03bf07620ca9a84075505..54f724e1774c2c718cddd1ddc7378054f2b2f638 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-phycore-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-phycore-som.dtsi
@@ -1,7 +1,6 @@
-// SPDX-License-Identifier: GPL-2.0
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
 /*
  * Copyright (C) 2022 PHYTEC Messtechnik GmbH
- * Author: Teresa Remmet <t.remmet@phytec.de>
  */
 
 #include "imx8mm.dtsi"

-- 
2.43.0

[PATCH v3 2/6] arm64: dts: imx8mm-phyboard-polis: move mipi bridge to som

[Jan Remmet]

sn65dsi83 is mounted on som. Add the static configuration there.
So it can be used by other boards too.
Use mipi_dsi_out from imx8mm.dtsi directly.

Signed-off-by: Jan Remmet <j.remmet@phytec.de>
---
 .../freescale/imx8mm-phyboard-polis-peb-av-10.dtso | 40 ++++------------------
 .../boot/dts/freescale/imx8mm-phycore-som.dtsi     | 25 ++++++++++++++
 2 files changed, 31 insertions(+), 34 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtso b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtso
index 00da1eedf73aac1f0e87383ac3d12f21e007c4cc..7e60c96b3562f4baf19bcdda8940c2b0c52dd743 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtso
+++ b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtso
@@ -81,6 +81,12 @@ dailink_master: simple-audio-card,codec {
 	};
 };
 
+&bridge_out {
+	remote-endpoint = <&panel_in>;
+	ti,lvds-vod-swing-clock-microvolt = <200000 600000>;
+	ti,lvds-vod-swing-data-microvolt = <200000 600000>;
+};
+
 &i2c3 {
 	clock-frequency = <400000>;
 	pinctrl-names = "default", "gpio";
@@ -128,19 +134,7 @@ &lcdif {
 };
 
 &mipi_dsi {
-	samsung,esc-clock-frequency = <10000000>;
 	status = "okay";
-
-	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		port@1 {
-			reg = <1>;
-			dsi_out: endpoint {
-				remote-endpoint = <&bridge_in>;
-			};
-		};
-	};
 };
 
 &pwm4 {
@@ -168,28 +162,6 @@ &sai5 {
 
 &sn65dsi83 {
 	status = "okay";
-
-	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		port@0 {
-			reg = <0>;
-			bridge_in: endpoint {
-				remote-endpoint = <&dsi_out>;
-				data-lanes = <1 2 3 4>;
-			};
-		};
-
-		port@2 {
-			reg = <2>;
-			bridge_out: endpoint {
-				remote-endpoint = <&panel_in>;
-				ti,lvds-vod-swing-clock-microvolt = <200000 600000>;
-				ti,lvds-vod-swing-data-microvolt = <200000 600000>;
-			};
-		};
-	};
 };
 
 &iomuxc {
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-phycore-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-phycore-som.dtsi
index 54f724e1774c2c718cddd1ddc7378054f2b2f638..3d66c6701342ae20839254674261c8264beccde5 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-phycore-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-phycore-som.dtsi
@@ -287,6 +287,23 @@ sn65dsi83: bridge@2d {
 		reg = <0x2d>;
 		vcc-supply = <&reg_vdd_1v8>;
 		status = "disabled";
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				bridge_in: endpoint {
+					remote-endpoint = <&mipi_dsi_out>;
+					data-lanes = <1 2 3 4>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+				bridge_out: endpoint {};
+			};
+		};
 	};
 
 	/* EEPROM */
@@ -304,6 +321,14 @@ rv3028: rtc@52 {
 	};
 };
 
+&mipi_dsi {
+	samsung,esc-clock-frequency = <10000000>;
+};
+
+&mipi_dsi_out {
+	remote-endpoint = <&bridge_in>;
+};
+
 /* eMMC */
 &usdhc3 {
 	assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>;

-- 
2.43.0

[PATCH v3 3/6] arm64: dts: imx8mm-phyboard-polis-peb-av-10: reorder properties to match dts coding style

[Jan Remmet]

Sort properties. Rename regulator label to match schematics.

Signed-off-by: Jan Remmet <j.remmet@phytec.de>
---
 .../freescale/imx8mm-phyboard-polis-peb-av-10.dtso | 48 +++++++++++-----------
 1 file changed, 24 insertions(+), 24 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtso b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtso
index 7e60c96b3562f4baf19bcdda8940c2b0c52dd743..d08f73da75962e1e2bd1e4a25913a13c3f366323 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtso
+++ b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtso
@@ -13,13 +13,13 @@
 &{/} {
 	backlight: backlight {
 		compatible = "pwm-backlight";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_lcd>;
-		default-brightness-level = <6>;
-		pwms = <&pwm4 0 50000 0>;
-		power-supply = <&reg_vdd_3v3_s>;
-		enable-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+		enable-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&pinctrl_lcd>;
+		pinctrl-names = "default";
+		power-supply = <&reg_vdd_3v3_s>;
+		pwms = <&pwm4 0 50000 0>;
 	};
 
 	panel {
@@ -34,27 +34,27 @@ panel_in: endpoint {
 		};
 	};
 
-	reg_sound_1v8: regulator-1v8 {
+	reg_vcc_1v8_audio: regulator-1v8 {
 		compatible = "regulator-fixed";
-		regulator-name = "VCC_1V8_Audio";
-		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <1800000>;
+		regulator-min-microvolt = <1800000>;
+		regulator-name = "VCC_1V8_Audio";
 	};
 
-	reg_sound_3v3: regulator-3v3 {
+	reg_vcc_3v3_analog: regulator-3v3 {
 		compatible = "regulator-fixed";
-		regulator-name = "VCC_3V3_Analog";
-		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "VCC_3V3_Analog";
 	};
 
 	sound-peb-av-10 {
 		compatible = "simple-audio-card";
-		simple-audio-card,name = "snd-peb-av-10";
-		simple-audio-card,format = "i2s";
 		simple-audio-card,bitclock-master = <&dailink_master>;
+		simple-audio-card,format = "i2s";
 		simple-audio-card,frame-master = <&dailink_master>;
 		simple-audio-card,mclk-fs = <32>;
+		simple-audio-card,name = "snd-peb-av-10";
 		simple-audio-card,widgets =
 			"Line", "Line In",
 			"Speaker", "Speaker",
@@ -89,28 +89,28 @@ &bridge_out {
 
 &i2c3 {
 	clock-frequency = <400000>;
-	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c3>;
 	pinctrl-1 = <&pinctrl_i2c3_gpio>;
-	sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	pinctrl-names = "default", "gpio";
 	scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	#address-cells = <1>;
 	#size-cells = <0>;
 	status = "okay";
 
 	codec: codec@18 {
 		compatible = "ti,tlv320aic3007";
-		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_tlv320>;
+		pinctrl-names = "default";
 		#sound-dai-cells = <0>;
 		reg = <0x18>;
-		reset-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
 		ai3x-gpio-func = <0xd 0x0>;
 		ai3x-micbias-vg = <2>;
-		AVDD-supply = <&reg_sound_3v3>;
-		IOVDD-supply = <&reg_sound_3v3>;
-		DRVDD-supply = <&reg_sound_3v3>;
-		DVDD-supply = <&reg_sound_1v8>;
+		reset-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
+		AVDD-supply = <&reg_vcc_3v3_analog>;
+		DRVDD-supply = <&reg_vcc_3v3_analog>;
+		DVDD-supply = <&reg_vcc_1v8_audio>;
+		IOVDD-supply = <&reg_vcc_3v3_analog>;
 	};
 
 	eeprom@57 {
@@ -138,8 +138,8 @@ &mipi_dsi {
 };
 
 &pwm4 {
-	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
+	pinctrl-names = "default";
 	status = "okay";
 };
 
@@ -154,8 +154,8 @@ &sai5 {
 	clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k",
 			"pll11k";
 	fsl,sai-mclk-direction-output;
-	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_sai5>;
+	pinctrl-names = "default";
 	#sound-dai-cells = <0>;
 	status = "okay";
 };

-- 
2.43.0

[PATCH v3 4/6] arm64: dts: imx8mm-phyboard-polis-peb-av-10: split display configuration

[Jan Remmet]

The PEB-AV-10 board can be used with different displays or in audio-only
mode.
Split the device tree overlays to reflect these use cases. To use the
board with the EDT ETML1010G3DRA display, the overlay
imx8mm-phyboard-polis-peb-av-10-etml1010g3dra.dtbo must now be used
instead of imx8mm-phyboard-polis-peb-av-10.dtbo.

Signed-off-by: Jan Remmet <j.remmet@phytec.de>
---
 arch/arm64/boot/dts/freescale/Makefile             |   3 +
 ...8mm-phyboard-polis-peb-av-10-etml1010g3dra.dtso |  44 +++++
 .../freescale/imx8mm-phyboard-polis-peb-av-10.dtsi | 189 +++++++++++++++++++
 .../freescale/imx8mm-phyboard-polis-peb-av-10.dtso | 203 +--------------------
 4 files changed, 237 insertions(+), 202 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 75676b90829956f79f64adb78bdb8ff2c9524ef1..a577783999df4156523a2f1424e16e9a707e2917 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -136,12 +136,15 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-phg.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-phyboard-polis-rdk.dtb
 
 imx8mm-phyboard-polis-peb-av-10-dtbs += imx8mm-phyboard-polis-rdk.dtb imx8mm-phyboard-polis-peb-av-10.dtbo
+imx8mm-phyboard-polis-peb-av-10-etml1010g3dra-dtbs += imx8mm-phyboard-polis-rdk.dtb \
+	imx8mm-phyboard-polis-peb-av-10-etml1010g3dra.dtbo
 imx8mm-phyboard-polis-peb-eval-01-dtbs += imx8mm-phyboard-polis-rdk.dtb imx8mm-phyboard-polis-peb-eval-01.dtbo
 imx8mm-phycore-no-eth-dtbs += imx8mm-phyboard-polis-rdk.dtb imx8mm-phycore-no-eth.dtbo
 imx8mm-phycore-no-spiflash-dtbs += imx8mm-phyboard-polis-rdk.dtb imx8mm-phycore-no-spiflash.dtbo
 imx8mm-phycore-rpmsg-dtbs += imx8mm-phyboard-polis-rdk.dtb imx8mm-phycore-rpmsg.dtbo
 
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-phyboard-polis-peb-av-10.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-phyboard-polis-peb-av-10-etml1010g3dra.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-phyboard-polis-peb-eval-01.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-phycore-no-eth.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-phycore-no-spiflash.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10-etml1010g3dra.dtso b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10-etml1010g3dra.dtso
new file mode 100644
index 0000000000000000000000000000000000000000..193fa9dc34d4a877fba13b072fedbe7c61018f0a
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10-etml1010g3dra.dtso
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright (C) 2025 PHYTEC Messtechnik GmbH
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "imx8mm-phyboard-polis-peb-av-10.dtsi"
+
+&backlight {
+	brightness-levels = <0 4 8 16 32 64 128 255>;
+	default-brightness-level = <6>;
+	enable-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+	pwms = <&pwm4 0 50000 0>;
+	status = "okay";
+};
+
+&bridge_out {
+	ti,lvds-vod-swing-clock-microvolt = <200000 600000>;
+	ti,lvds-vod-swing-data-microvolt = <200000 600000>;
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&mipi_dsi {
+	status = "okay";
+};
+
+&panel {
+	compatible = "edt,etml1010g3dra";
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+&sn65dsi83 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtsi
new file mode 100644
index 0000000000000000000000000000000000000000..3d4ffeecb8dd8e6f7a68eeafba761534fae9deb4
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtsi
@@ -0,0 +1,189 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright (C) 2025 PHYTEC Messtechnik GmbH
+ */
+
+#include <dt-bindings/clock/imx8mm-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "imx8mm-pinfunc.h"
+
+&{/} {
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lcd>;
+		power-supply = <&reg_vdd_3v3_s>;
+		status = "disabled";
+	};
+
+	panel: panel {
+		backlight = <&backlight>;
+		power-supply = <&reg_vcc_3v3>;
+		status = "disabled";
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&bridge_out>;
+			};
+		};
+	};
+
+	reg_sound_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_1V8_Audio";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_sound_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3_Analog";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	sound-peb-av-10 {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "snd-peb-av-10";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&dailink_master>;
+		simple-audio-card,frame-master = <&dailink_master>;
+		simple-audio-card,mclk-fs = <32>;
+		simple-audio-card,widgets =
+			"Line", "Line In",
+			"Speaker", "Speaker",
+			"Microphone", "Microphone Jack",
+			"Headphone", "Headphone Jack";
+		simple-audio-card,routing =
+			"Speaker", "SPOP",
+			"Speaker", "SPOM",
+			"Headphone Jack", "HPLOUT",
+			"Headphone Jack", "HPROUT",
+			"LINE1L", "Line In",
+			"LINE1R", "Line In",
+			"MIC3R", "Microphone Jack",
+			"Microphone Jack", "Mic Bias";
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai5>;
+		};
+
+		dailink_master: simple-audio-card,codec {
+			sound-dai = <&codec>;
+			clocks = <&clk IMX8MM_CLK_SAI5>;
+		};
+	};
+};
+
+&bridge_out {
+	remote-endpoint = <&panel_in>;
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	codec: codec@18 {
+		compatible = "ti,tlv320aic3007";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tlv320>;
+		#sound-dai-cells = <0>;
+		reg = <0x18>;
+		reset-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
+		ai3x-gpio-func = <0xd 0x0>;
+		ai3x-micbias-vg = <2>;
+		AVDD-supply = <&reg_sound_3v3>;
+		IOVDD-supply = <&reg_sound_3v3>;
+		DRVDD-supply = <&reg_sound_3v3>;
+		DVDD-supply = <&reg_sound_1v8>;
+	};
+
+	eeprom@57 {
+		compatible = "atmel,24c32";
+		pagesize = <32>;
+		reg = <0x57>;
+		vcc-supply = <&reg_vdd_3v3_s>;
+	};
+
+	eeprom@5f {
+		compatible = "atmel,24c32";
+		pagesize = <32>;
+		reg = <0x5f>;
+		size = <32>;
+		vcc-supply = <&reg_vdd_3v3_s>;
+	};
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+};
+
+&sai5 {
+	assigned-clocks = <&clk IMX8MM_CLK_SAI5>;
+	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL2_OUT>;
+	assigned-clock-rates = <11289600>;
+	clocks = <&clk IMX8MM_CLK_SAI5_IPG>, <&clk IMX8MM_CLK_DUMMY>,
+		<&clk IMX8MM_CLK_SAI5_ROOT>, <&clk IMX8MM_CLK_DUMMY>,
+		<&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_AUDIO_PLL1_OUT>,
+		<&clk IMX8MM_AUDIO_PLL2_OUT>;
+	clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k",
+			"pll11k";
+	fsl,sai-mclk-direction-output;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai5>;
+	#sound-dai-cells = <0>;
+	status = "okay";
+};
+
+&iomuxc {
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL          0x400001c2
+			MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA          0x400001c2
+		>;
+	};
+
+	pinctrl_i2c3_gpio: i2c3gpiogrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C3_SCL_GPIO5_IO18        0x1e2
+			MX8MM_IOMUXC_I2C3_SDA_GPIO5_IO19        0x1e2
+		>;
+	};
+	pinctrl_lcd: lcd0grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1		0x12
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_MCLK_PWM4_OUT		0x12
+		>;
+	};
+
+	pinctrl_sai5: sai5grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_MCLK_SAI5_MCLK        0xd6
+			MX8MM_IOMUXC_SAI5_RXD0_SAI5_RX_DATA0    0xd6
+			MX8MM_IOMUXC_SAI5_RXD1_SAI5_TX_SYNC     0xd6
+			MX8MM_IOMUXC_SAI5_RXD2_SAI5_TX_BCLK     0xd6
+			MX8MM_IOMUXC_SAI5_RXD3_SAI5_TX_DATA0    0xd6
+		>;
+	};
+
+	pinctrl_tlv320: tlv320grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28       0x16
+			MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20        0x16
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtso b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtso
index d08f73da75962e1e2bd1e4a25913a13c3f366323..28e8589f9f951ad79dfcd4d0ca2335fafdc683cd 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtso
+++ b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtso
@@ -6,205 +6,4 @@
 /dts-v1/;
 /plugin/;
 
-#include <dt-bindings/clock/imx8mm-clock.h>
-#include <dt-bindings/gpio/gpio.h>
-#include "imx8mm-pinfunc.h"
-
-&{/} {
-	backlight: backlight {
-		compatible = "pwm-backlight";
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <6>;
-		enable-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
-		pinctrl-0 = <&pinctrl_lcd>;
-		pinctrl-names = "default";
-		power-supply = <&reg_vdd_3v3_s>;
-		pwms = <&pwm4 0 50000 0>;
-	};
-
-	panel {
-		compatible = "edt,etml1010g3dra";
-		backlight = <&backlight>;
-		power-supply = <&reg_vcc_3v3>;
-
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&bridge_out>;
-			};
-		};
-	};
-
-	reg_vcc_1v8_audio: regulator-1v8 {
-		compatible = "regulator-fixed";
-		regulator-max-microvolt = <1800000>;
-		regulator-min-microvolt = <1800000>;
-		regulator-name = "VCC_1V8_Audio";
-	};
-
-	reg_vcc_3v3_analog: regulator-3v3 {
-		compatible = "regulator-fixed";
-		regulator-max-microvolt = <3300000>;
-		regulator-min-microvolt = <3300000>;
-		regulator-name = "VCC_3V3_Analog";
-	};
-
-	sound-peb-av-10 {
-		compatible = "simple-audio-card";
-		simple-audio-card,bitclock-master = <&dailink_master>;
-		simple-audio-card,format = "i2s";
-		simple-audio-card,frame-master = <&dailink_master>;
-		simple-audio-card,mclk-fs = <32>;
-		simple-audio-card,name = "snd-peb-av-10";
-		simple-audio-card,widgets =
-			"Line", "Line In",
-			"Speaker", "Speaker",
-			"Microphone", "Microphone Jack",
-			"Headphone", "Headphone Jack";
-		simple-audio-card,routing =
-			"Speaker", "SPOP",
-			"Speaker", "SPOM",
-			"Headphone Jack", "HPLOUT",
-			"Headphone Jack", "HPROUT",
-			"LINE1L", "Line In",
-			"LINE1R", "Line In",
-			"MIC3R", "Microphone Jack",
-			"Microphone Jack", "Mic Bias";
-
-		simple-audio-card,cpu {
-			sound-dai = <&sai5>;
-		};
-
-		dailink_master: simple-audio-card,codec {
-			sound-dai = <&codec>;
-			clocks = <&clk IMX8MM_CLK_SAI5>;
-		};
-	};
-};
-
-&bridge_out {
-	remote-endpoint = <&panel_in>;
-	ti,lvds-vod-swing-clock-microvolt = <200000 600000>;
-	ti,lvds-vod-swing-data-microvolt = <200000 600000>;
-};
-
-&i2c3 {
-	clock-frequency = <400000>;
-	pinctrl-0 = <&pinctrl_i2c3>;
-	pinctrl-1 = <&pinctrl_i2c3_gpio>;
-	pinctrl-names = "default", "gpio";
-	scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-	sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-	#address-cells = <1>;
-	#size-cells = <0>;
-	status = "okay";
-
-	codec: codec@18 {
-		compatible = "ti,tlv320aic3007";
-		pinctrl-0 = <&pinctrl_tlv320>;
-		pinctrl-names = "default";
-		#sound-dai-cells = <0>;
-		reg = <0x18>;
-		ai3x-gpio-func = <0xd 0x0>;
-		ai3x-micbias-vg = <2>;
-		reset-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
-		AVDD-supply = <&reg_vcc_3v3_analog>;
-		DRVDD-supply = <&reg_vcc_3v3_analog>;
-		DVDD-supply = <&reg_vcc_1v8_audio>;
-		IOVDD-supply = <&reg_vcc_3v3_analog>;
-	};
-
-	eeprom@57 {
-		compatible = "atmel,24c32";
-		pagesize = <32>;
-		reg = <0x57>;
-		vcc-supply = <&reg_vdd_3v3_s>;
-	};
-
-	eeprom@5f {
-		compatible = "atmel,24c32";
-		pagesize = <32>;
-		reg = <0x5f>;
-		size = <32>;
-		vcc-supply = <&reg_vdd_3v3_s>;
-	};
-};
-
-&lcdif {
-	status = "okay";
-};
-
-&mipi_dsi {
-	status = "okay";
-};
-
-&pwm4 {
-	pinctrl-0 = <&pinctrl_pwm4>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&sai5 {
-	assigned-clocks = <&clk IMX8MM_CLK_SAI5>;
-	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL2_OUT>;
-	assigned-clock-rates = <11289600>;
-	clocks = <&clk IMX8MM_CLK_SAI5_IPG>, <&clk IMX8MM_CLK_DUMMY>,
-		<&clk IMX8MM_CLK_SAI5_ROOT>, <&clk IMX8MM_CLK_DUMMY>,
-		<&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_AUDIO_PLL1_OUT>,
-		<&clk IMX8MM_AUDIO_PLL2_OUT>;
-	clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k",
-			"pll11k";
-	fsl,sai-mclk-direction-output;
-	pinctrl-0 = <&pinctrl_sai5>;
-	pinctrl-names = "default";
-	#sound-dai-cells = <0>;
-	status = "okay";
-};
-
-&sn65dsi83 {
-	status = "okay";
-};
-
-&iomuxc {
-
-	pinctrl_i2c3: i2c3grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL          0x400001c2
-			MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA          0x400001c2
-		>;
-	};
-
-	pinctrl_i2c3_gpio: i2c3gpiogrp {
-		fsl,pins = <
-			MX8MM_IOMUXC_I2C3_SCL_GPIO5_IO18        0x1e2
-			MX8MM_IOMUXC_I2C3_SDA_GPIO5_IO19        0x1e2
-		>;
-	};
-	pinctrl_lcd: lcd0grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1		0x12
-		>;
-	};
-
-	pinctrl_pwm4: pwm4grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SAI3_MCLK_PWM4_OUT		0x12
-		>;
-	};
-
-	pinctrl_sai5: sai5grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SAI5_MCLK_SAI5_MCLK        0xd6
-			MX8MM_IOMUXC_SAI5_RXD0_SAI5_RX_DATA0    0xd6
-			MX8MM_IOMUXC_SAI5_RXD1_SAI5_TX_SYNC     0xd6
-			MX8MM_IOMUXC_SAI5_RXD2_SAI5_TX_BCLK     0xd6
-			MX8MM_IOMUXC_SAI5_RXD3_SAI5_TX_DATA0    0xd6
-		>;
-	};
-
-	pinctrl_tlv320: tlv320grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28       0x16
-			MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20        0x16
-		>;
-	};
-};
+#include "imx8mm-phyboard-polis-peb-av-10.dtsi"

-- 
2.43.0

[PATCH v3 5/6] arm64: dts: imx8mm-phyboard-polis-peb-av-10-ph128800t006

[Jan Remmet]

Add support for powertip,ph128800t006-zhc01 connected via peb-av-10

Signed-off-by: Jan Remmet <j.remmet@phytec.de>
---
 arch/arm64/boot/dts/freescale/Makefile             |  3 ++
 ...x8mm-phyboard-polis-peb-av-10-ph128800t006.dtso | 44 ++++++++++++++++++++++
 2 files changed, 47 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index a577783999df4156523a2f1424e16e9a707e2917..7bcd10ce4defb5c6f539fe89d5559f3061cbe837 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -138,6 +138,8 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-phyboard-polis-rdk.dtb
 imx8mm-phyboard-polis-peb-av-10-dtbs += imx8mm-phyboard-polis-rdk.dtb imx8mm-phyboard-polis-peb-av-10.dtbo
 imx8mm-phyboard-polis-peb-av-10-etml1010g3dra-dtbs += imx8mm-phyboard-polis-rdk.dtb \
 	imx8mm-phyboard-polis-peb-av-10-etml1010g3dra.dtbo
+imx8mm-phyboard-polis-peb-av-10-ph128800t006-dtbs += imx8mm-phyboard-polis-rdk.dtb \
+	imx8mm-phyboard-polis-peb-av-10-ph128800t006.dtbo
 imx8mm-phyboard-polis-peb-eval-01-dtbs += imx8mm-phyboard-polis-rdk.dtb imx8mm-phyboard-polis-peb-eval-01.dtbo
 imx8mm-phycore-no-eth-dtbs += imx8mm-phyboard-polis-rdk.dtb imx8mm-phycore-no-eth.dtbo
 imx8mm-phycore-no-spiflash-dtbs += imx8mm-phyboard-polis-rdk.dtb imx8mm-phycore-no-spiflash.dtbo
@@ -145,6 +147,7 @@ imx8mm-phycore-rpmsg-dtbs += imx8mm-phyboard-polis-rdk.dtb imx8mm-phycore-rpmsg.
 
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-phyboard-polis-peb-av-10.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-phyboard-polis-peb-av-10-etml1010g3dra.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-phyboard-polis-peb-av-10-ph128800t006.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-phyboard-polis-peb-eval-01.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-phycore-no-eth.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-phycore-no-spiflash.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10-ph128800t006.dtso b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10-ph128800t006.dtso
new file mode 100644
index 0000000000000000000000000000000000000000..fd819bd563b8f609101c57974c682eb56c12b144
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10-ph128800t006.dtso
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright (C) 2025 PHYTEC Messtechnik GmbH
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "imx8mm-phyboard-polis-peb-av-10.dtsi"
+
+&backlight {
+	brightness-levels = <0 4 8 16 32 64 128 255>;
+	default-brightness-level = <6>;
+	enable-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+	pwms = <&pwm4 0 50000 0>;
+	status = "okay";
+};
+
+&bridge_out {
+	ti,lvds-vod-swing-clock-microvolt = <200000 600000>;
+	ti,lvds-vod-swing-data-microvolt = <200000 600000>;
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&mipi_dsi {
+	status = "okay";
+};
+
+&panel {
+	compatible = "powertip,ph128800t006-zhc01";
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+&sn65dsi83 {
+	status = "okay";
+};

-- 
2.43.0

[PATCH v3 6/6] arm64: dts: imx8mm-phyboard-polis-peb-av-10: Fix audio codec reset pin ctl

[Jan Remmet]

From: Teresa Remmet <t.remmet@phytec.de>

Enable internal pull up of the active low audio codec reset pin.
Otherwise the audio codec does not reset properly and is not working.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Jan Remmet <j.remmet@phytec.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtsi
index 3d4ffeecb8dd8e6f7a68eeafba761534fae9deb4..bd1f255e15ea95b6f59e2c7bd762d6a6a2b4ab76 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-peb-av-10.dtsi
@@ -182,7 +182,7 @@ MX8MM_IOMUXC_SAI5_RXD3_SAI5_TX_DATA0    0xd6
 
 	pinctrl_tlv320: tlv320grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28       0x16
+			MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28       0x116
 			MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20        0x16
 		>;
 	};

-- 
2.43.0

AW: [PATCH v3 0/6] arm64: dts: imx8mm-phyboard-polis: cleanup and additional display

[Janine Hagemann]

[-- Attachment #1: Type: text/plain, Size: 0 bytes --]



[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #2: ATT00001 --]
[-- Type: text/markdown; name="ATT00001", Size: 2865 bytes --]

  


  

Von: Jan Remmet <j.remmet@phytec.de>  
Gesendet: Dienstag, 28. Oktober 2025 09:58  
An: Teresa Remmet <t.remmet@phytec.de>; Janine Hagemann <j.hagemann@phytec.de>; Rob Herring <robh@kernel.org>; Krzysztof Kozlowski <krzk+dt@kernel.org>; Conor Dooley <conor+dt@kernel.org>; Shawn Guo <shawnguo@kernel.org>; Sascha Hauer <s.hauer@pengutronix.de>; Pengutronix Kernel Team <kernel@pengutronix.de>; Fabio Estevam <festevam@gmail.com>  
Cc: devicetree@vger.kernel.org <devicetree@vger.kernel.org>; imx@lists.linux.dev <imx@lists.linux.dev>; linux-arm-kernel@lists.infradead.org <linux-arm-kernel@lists.infradead.org>  
Betreff: [PATCH v3 0/6] arm64: dts: imx8mm-phyboard-polis: cleanup and additional display  
   
  
This patch stacks rework the handling of the peb-av-10 daughterboard.  
Update license.  
Move mipi bridge configuration to som.  
Allow peb-av-10 as audio only overlay.  
Add two display overlays for ETML1010G3DRA and PH128800T00.  
  
Signed-off-by: Jan Remmet <j.remmet@phytec.de>  

Acked-by: Janine Hagemann <j.hagemann@phytec.de>
---  
Changes in v3:  
- rebased onto shawnguo/for-next  
- add Acked-by  
- Link to v2: https://lore.kernel.org/r/20251007-wip-j-remmet-phytec-de-bspimx8m-3801_peb-av-10_with_ac209-v2-0-7e5de62c79bf@phytec.de  
  
Changes in v2:  
- add Signed-off-by to patch6  
- Link to v1: https://lore.kernel.org/r/20250930-wip-j-remmet-phytec-de-bspimx8m-3801_peb-av-10_with_ac209-v1-0-d5d03ccbfca1@phytec.de  
  
---  
Jan Remmet (5):  
      arm64: dts: imx8mm-phyboard-polis: Use GPL-2.0-or-later OR MIT  
      arm64: dts: imx8mm-phyboard-polis: move mipi bridge to som  
      arm64: dts: imx8mm-phyboard-polis-peb-av-10: reorder properties to match dts coding style  
      arm64: dts: imx8mm-phyboard-polis-peb-av-10: split display configuration  
      arm64: dts: imx8mm-phyboard-polis-peb-av-10-ph128800t006  
  
Teresa Remmet (1):  
      arm64: dts: imx8mm-phyboard-polis-peb-av-10: Fix audio codec reset pin ctl  
  
 arch/arm64/boot/dts/freescale/Makefile             |   6 +  
 ...8mm-phyboard-polis-peb-av-10-etml1010g3dra.dtso |  44 ++++  
 ...x8mm-phyboard-polis-peb-av-10-ph128800t006.dtso |  44 ++++  
 .../freescale/imx8mm-phyboard-polis-peb-av-10.dtsi | 189 +++++++++++++++++  
 .../freescale/imx8mm-phyboard-polis-peb-av-10.dtso | 234 +--------------------  
 .../imx8mm-phyboard-polis-peb-eval-01.dtso         |   3 +-  
 .../dts/freescale/imx8mm-phyboard-polis-rdk.dts    |   3 +-  
 .../boot/dts/freescale/imx8mm-phycore-som.dtsi     |  28 ++-  
 8 files changed, 313 insertions(+), 238 deletions(-)  
---  
base-commit: b61938e8910c5dc0eecaf319ff12d67a35e39d9f  
change-id: 20250925-wip-j-remmet-phytec-de-bspimx8m-3801_peb-av-10_with_ac209-ef10812a2d8d  
  
Best regards,  
--  
Jan Remmet <j.remmet@phytec.de>  

Re: [PATCH v3 0/6] arm64: dts: imx8mm-phyboard-polis: cleanup and additional display

[Shawn Guo]

On Tue, Oct 28, 2025 at 09:58:07AM +0100, Jan Remmet wrote:
> Jan Remmet (5):
>       arm64: dts: imx8mm-phyboard-polis: Use GPL-2.0-or-later OR MIT
>       arm64: dts: imx8mm-phyboard-polis: move mipi bridge to som
>       arm64: dts: imx8mm-phyboard-polis-peb-av-10: reorder properties to match dts coding style
>       arm64: dts: imx8mm-phyboard-polis-peb-av-10: split display configuration
>       arm64: dts: imx8mm-phyboard-polis-peb-av-10-ph128800t006
> 
> Teresa Remmet (1):
>       arm64: dts: imx8mm-phyboard-polis-peb-av-10: Fix audio codec reset pin ctl

Applied all, thanks!