From: Sebastian Reichel <sebastian.reichel@collabora.com>
To: Anand Moon <linux.amoon@gmail.com>
Cc: Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Heiko Stuebner <heiko@sntech.de>,
Heikki Krogerus <heikki.krogerus@linux.intel.com>,
Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Nicolas Frattaroli <nicolas.frattaroli@collabora.com>,
FUKAUMI Naoki <naoki@radxa.com>,
Diederik de Haas <didi.debian@cknow.org>,
Yongbo Zhang <giraffesnn123@gmail.com>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@vger.kernel.org>,
"moderated list:ARM/Rockchip SoC support"
<linux-arm-kernel@lists.infradead.org>,
"open list:ARM/Rockchip SoC support"
<linux-rockchip@lists.infradead.org>,
open list <linux-kernel@vger.kernel.org>,
"open list:USB TYPEC CLASS" <linux-usb@vger.kernel.org>
Subject: Re: [PATCH v1 1/3] arm64: dts: rockchip: rk3588-rock-5b-5bp-5t: Correct Type-C pin bias settings
Date: Sat, 3 Jan 2026 14:52:50 +0100 [thread overview]
Message-ID: <aVke1kQnHJLqWGHi@venus> (raw)
In-Reply-To: <20260103083232.9510-2-linux.amoon@gmail.com>
[-- Attachment #1: Type: text/plain, Size: 2334 bytes --]
Hi,
On Sat, Jan 03, 2026 at 02:01:17PM +0530, Anand Moon wrote:
> As pre FUSB302 datasheet interrupt line (INT_N) is an open-drain,
> active-low signal. It requires a pull-up resistor to maintain a stable
> high state when deasserted. Similarly, the TYPEC5V_PWREN_H enable signal
> requires a pull-down resistor to ensure it defaults to a low state,
> preventing unintended power delivery during the boot sequence.
>
> Update the pinctrl entries to use pcfg_pull_up for usbc0_int and
> pcfg_pull_down for vbus5v0_typec_en to align with the hardware's
> electrical requirements.
>
> Cc: Sebastian Reichel <sebastian.reichel@collabora.com>
> Fixes: 67b2c15d8fb3 ("arm64: dts: rockchip: add USB-C support for ROCK 5B/5B+/5T")
> Signed-off-by: Anand Moon <linux.amoon@gmail.com>
> ---
> v1: As per the shematics CC_INT_L interrupt pin is GPIO3_B4_u
> As per the shematics TYPEC5V_PWREN_H pin is GPIO2_B6_d
> ---
Checking the schematics:
5B v1.45 - CC_INT_L - R2613 10K pull-up resistor
5B v1.45 - TYPEC5V_PWREN_H - GPIO is effectively unused because R95035 is NC
5B+ v1.2 - CC_INT_L - R2613 10K pull-up resistor
5B+ v1.2 - TYPEC5V_PWREN_H - R163 100K pull-down resistor
5T v1.2 - CC_INT_L - R2613 10K pull-up resistor
5T v1.2 - TYPEC5V_PWREN_H - R163 100K pull-down resistor
TLDR: All GPIOs have pull resistors in discrete hardware and do not
need them muxed in the SoC.
Greetings,
-- Sebastian
> arch/arm64/boot/dts/rockchip/rk3588-rock-5b-5bp-5t.dtsi | 4 ++--
> 1 file changed, 2 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/rockchip/rk3588-rock-5b-5bp-5t.dtsi b/arch/arm64/boot/dts/rockchip/rk3588-rock-5b-5bp-5t.dtsi
> index b3e76ad2d869..0cd8ac7bf538 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3588-rock-5b-5bp-5t.dtsi
> +++ b/arch/arm64/boot/dts/rockchip/rk3588-rock-5b-5bp-5t.dtsi
> @@ -537,11 +537,11 @@ pcie3_vcc3v3_en: pcie3-vcc3v3-en {
>
> usb {
> usbc0_int: usbc0-int {
> - rockchip,pins = <3 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>;
> + rockchip,pins = <3 RK_PB4 RK_FUNC_GPIO &pcfg_pull_up>;
> };
>
> vbus5v0_typec_en: vbus5v0-typec-en {
> - rockchip,pins = <2 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>;
> + rockchip,pins = <2 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
> };
> };
> };
> --
> 2.50.1
>
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
next prev parent reply other threads:[~2026-01-03 13:53 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-01-03 8:31 [PATCH v1 0/3] Typc fusb302 powerloss issue on Radxa Rock 5b Anand Moon
2026-01-03 8:31 ` [PATCH v1 1/3] arm64: dts: rockchip: rk3588-rock-5b-5bp-5t: Correct Type-C pin bias settings Anand Moon
2026-01-03 13:52 ` Sebastian Reichel [this message]
2026-01-03 8:31 ` [PATCH v1 2/3] arm64: dts: rockchip: rk3588-rock-5b-5bp-5t: Fix USB host phy-supply on Rock 5b-5bp-5t SbC Anand Moon
2026-01-03 14:04 ` Sebastian Reichel
2026-01-03 8:31 ` [PATCH v1 3/3] usb: typec: fusb302: Switch to threaded interrupt handler Anand Moon
2026-01-03 12:01 ` Hans de Goede
2026-01-07 9:52 ` 张永波
2026-01-07 10:52 ` Hans de Goede
2026-01-03 14:24 ` [PATCH v1 0/3] Typc fusb302 powerloss issue on Radxa Rock 5b Sebastian Reichel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=aVke1kQnHJLqWGHi@venus \
--to=sebastian.reichel@collabora.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=didi.debian@cknow.org \
--cc=giraffesnn123@gmail.com \
--cc=gregkh@linuxfoundation.org \
--cc=heikki.krogerus@linux.intel.com \
--cc=heiko@sntech.de \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-rockchip@lists.infradead.org \
--cc=linux-usb@vger.kernel.org \
--cc=linux.amoon@gmail.com \
--cc=naoki@radxa.com \
--cc=nicolas.frattaroli@collabora.com \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).