Linux-ARM-Kernel Archive on lore.kernel.org
 help / color / mirror / Atom feed
From: Marcus Folkesson <marcus.folkesson@gmail.com>
To: Wolfram Sang <wsa+renesas@sang-engineering.com>,
	Peter Rosin <peda@axentia.se>,
	Michael Hennerich <michael.hennerich@analog.com>,
	Bartosz Golaszewski <brgl@bgdev.pl>,
	Andi Shyti <andi.shyti@kernel.org>,
	Andy Shevchenko <andriy.shevchenko@intel.com>,
	Bartosz Golaszewski <brgl@kernel.org>
Cc: linux-i2c@vger.kernel.org, linux-kernel@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH v9 0/5] I2C Mux per channel bus speed
Date: Fri, 8 May 2026 15:14:31 +0200	[thread overview]
Message-ID: <af3ht8OX_VUYVAgg@gmail.com> (raw)
In-Reply-To: <20260324-i2c-mux-v9-0-5292b0608243@gmail.com>

On Tue, Mar 24, 2026 at 02:54:14PM +0100, Marcus Folkesson wrote:
> This was a RFC on how to implement a feature to have different bus
> speeds on different channels with an I2C multiplexer/switch.
> As no major complaints on the design came up during the review, I
> decided to submit the series without the RFC tag.
> 
> The benefit with this feature is that you may group devices after
> the fastest bus speed they can handle.
> A real-world example is that you could have e.g. a display running @400kHz
> and a smart battery running @100kHz using the same I2C controller.
> 
> There are many corner cases where this may cause a problem for some
> hardware topologies. I've tried to describe those I could think of
> in the documentation, see Patch #5.
> 
> E.g. one risk is that if the mux driver does not disconnect channels
> when Idle, this may cause a higher frequency to "leak" through to
> devices that are supposed to run at lower bus speed.
> This is not only a "problem" for changing bus speed but could also be
> an issue for potential address conflicts.
> 
> This patchset has been used and tested heavily the last months
> on a custom board based on a da850 (DaVinci) platform.
> 
> The implementation is split up into several patches:
> 
> Patch #1 Introduce a callback for the i2c controller to set bus speed
> Patch #2 Introduce functionality to adjust bus speed depending on mux
>          channel.
> Patch #3 Cleanup i2c-davinci driver a bit to prepare it for set_clk_freq
> Parch #4 Implement set_clk_freq for the i2c-davinci driver
> Parch #5 Update documentation with this feature
> 
> Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
> ---
> Changes in v9:
> - Fix stray blank line
> - Link to v8: https://lore.kernel.org/r/20260314-i2c-mux-v8-0-fb1738a4df0a@gmail.com
> 
> Changes in v8:
> - Fix gramatics and change %d to %u were appropriate
> - Link to v7: https://lore.kernel.org/r/20260223-i2c-mux-v7-0-ec75b214718a@gmail.com
> 
> Changes in v7:
> - Remove code for finding first mux-locked ancestor
> - Introduce a unlocked (i2c_adapter_set_clk_freq) and unlocked
>   (__i2c_adapter_set_clk_freq) variant
> - Let the locking be handled in __i2c_adapter_set_clk_freq
> - Use I2C_MAX_STANDARD_MODE_FREQ instead of magic numbers where
>   appropriate 
> - Link to v6: https://lore.kernel.org/r/20260216-i2c-mux-v6-0-9be28ecfd7e3@gmail.com
> 
> Changes in v6:
> - Change logic to find which ancestor to lock with I2C_LOCK_ROOT_ADAPTER
>   It now find the first mux-locked ancestor and then lock its parent.
> 
> - Remove bus_freq_hz in i2c-davinci and only use clock_hz instead
> - Mention in commit message that clock_hz can be used to store frequency in an uniform way
> 
> - Swap order for change freq/deselect to keep symmetry
> - Only allow bus frequency to be lowered in select()
>   This to not allow an intermediate frequency to be set when it is not
>   supposed to
> 
> - check if(ret) instead of ret(<0) where appropriate
> - Fix typos in documentation
> - Change i2c_adapter.clock_hz from int to u32
> - Simplify i2c_adapter_set_clk_freq() by removing 'ret'
> - Link to v5: https://lore.kernel.org/r/20260213-i2c-mux-v5-0-fb2cbf9979b3@gmail.com
> 
> Changes in v5:
> - Take the lock of the top-most mutex locked mux to make sure that the
>   root is locked
> - Link to v4: https://lore.kernel.org/r/20260128-i2c-mux-v4-0-dee49ce276c0@gmail.com
> 
> Changes in v4:
> - Rebase on master
> - Swap order for printing warning about "channel %u is slower than
>   parent on a non parent-locked mux\n"
> - Fix typo in comment, adaper->adapter
> - Link to v3: https://lore.kernel.org/r/20251020-i2c-mux-v3-0-908ac5cf9223@gmail.com
> 
> Changes in v3:
> - Return -EINVAL if channel is faster than parent (kernel test robot)
> - Link to v2: https://lore.kernel.org/r/20251002-i2c-mux-v2-0-b698564cd956@gmail.com
> 
> Changes in v2:
> - Changed bus_freq field to bus_freq_hz in davinci_i2c_dev (Bartosz Golaszewski)
> - Removed idle_state from mux core (Peter Rosin)
> - Link to v1: https://lore.kernel.org/r/20250922-i2c-mux-v1-0-28c94a610930@gmail.com
> 
> ---

Friendly ping on this series.

Thanks,

Med vänliga hälsningar / Best regards
Marcus Folkesson


      parent reply	other threads:[~2026-05-08 13:14 UTC|newest]

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-03-24 13:54 [PATCH v9 0/5] I2C Mux per channel bus speed Marcus Folkesson
2026-03-24 13:54 ` [PATCH v9 1/5] i2c: core: add callback to change bus frequency Marcus Folkesson
2026-03-24 13:54 ` [PATCH v9 2/5] i2c: mux: add support for per channel " Marcus Folkesson
2026-03-24 14:10   ` Andy Shevchenko
2026-03-26 11:39     ` Marcus Folkesson
2026-03-24 13:54 ` [PATCH v9 3/5] i2c: davinci: calculate bus freq from Hz instead of kHz Marcus Folkesson
2026-03-24 13:54 ` [PATCH v9 4/5] i2c: davinci: add support for setting bus frequency Marcus Folkesson
2026-03-24 13:54 ` [PATCH v9 5/5] docs: i2c: i2c-topology: add section about bus speed Marcus Folkesson
2026-03-26 12:17 ` [PATCH v9 0/5] I2C Mux per channel " Marcus Folkesson
2026-04-13  7:45 ` Marcus Folkesson
2026-05-08 13:14 ` Marcus Folkesson [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=af3ht8OX_VUYVAgg@gmail.com \
    --to=marcus.folkesson@gmail.com \
    --cc=andi.shyti@kernel.org \
    --cc=andriy.shevchenko@intel.com \
    --cc=brgl@bgdev.pl \
    --cc=brgl@kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-i2c@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=michael.hennerich@analog.com \
    --cc=peda@axentia.se \
    --cc=wsa+renesas@sang-engineering.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox