From: eric.y.miao@gmail.com (Eric)
To: linux-arm-kernel@lists.infradead.org
Subject: [patch 08/16] arm: pxa: Use clocksource based sched_clock
Date: Tue, 26 Apr 2011 00:25:45 +0800 (CST) [thread overview]
Message-ID: <alpine.DEB.2.00.1104260023080.27645@localhost6.localdomain6> (raw)
In-Reply-To: <20110423205132.325774191@linutronix.de>
On Sat, 23 Apr 2011, Thomas Gleixner wrote:
> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
> ---
> arch/arm/mach-pxa/time.c | 31 +++----------------------------
I think we need to remove HAVE_SCHED_CLOCK from ARCH_PXA in
arch/arm/Kconfig as well.
Didn't look into other sub-arch, but should be applicable to those
selecting HAVE_SCHED_CLOCK.
> 1 file changed, 3 insertions(+), 28 deletions(-)
>
> Index: linux-2.6-tip/arch/arm/mach-pxa/time.c
> ===================================================================
> --- linux-2.6-tip.orig/arch/arm/mach-pxa/time.c
> +++ linux-2.6-tip/arch/arm/mach-pxa/time.c
> @@ -21,31 +21,8 @@
> #include <asm/div64.h>
> #include <asm/mach/irq.h>
> #include <asm/mach/time.h>
> -#include <asm/sched_clock.h>
> -#include <mach/regs-ost.h>
> -
> -/*
> - * This is PXA's sched_clock implementation. This has a resolution
> - * of at least 308 ns and a maximum value of 208 days.
> - *
> - * The return value is guaranteed to be monotonic in that range as
> - * long as there is always less than 582 seconds between successive
> - * calls to sched_clock() which should always be the case in practice.
> - */
> -static DEFINE_CLOCK_DATA(cd);
> -
> -unsigned long long notrace sched_clock(void)
> -{
> - u32 cyc = OSCR;
> - return cyc_to_sched_clock(&cd, cyc, (u32)~0);
> -}
> -
> -static void notrace pxa_update_sched_clock(void)
> -{
> - u32 cyc = OSCR;
> - update_sched_clock(&cd, cyc, (u32)~0);
> -}
>
> +#include <mach/regs-ost.h>
>
> #define MIN_OSCR_DELTA 16
>
> @@ -105,7 +82,7 @@ static struct clock_event_device ckevt_p
> .set_mode = pxa_osmr0_set_mode,
> };
>
> -static cycle_t pxa_read_oscr(struct clocksource *cs)
> +static cycle_t notrace pxa_read_oscr(struct clocksource *cs)
> {
> return OSCR;
> }
> @@ -115,7 +92,7 @@ static struct clocksource cksrc_pxa_oscr
> .rating = 200,
> .read = pxa_read_oscr,
> .mask = CLOCKSOURCE_MASK(32),
> - .flags = CLOCK_SOURCE_IS_CONTINUOUS,
> + .flags = CLOCK_SOURCE_IS_CONTINUOUS | CLOCK_SOURCE_SCHED_CLOCK,
> };
>
> static struct irqaction pxa_ost0_irq = {
> @@ -132,8 +109,6 @@ static void __init pxa_timer_init(void)
> OIER = 0;
> OSSR = OSSR_M0 | OSSR_M1 | OSSR_M2 | OSSR_M3;
>
> - init_sched_clock(&cd, pxa_update_sched_clock, 32, clock_tick_rate);
> -
> clocksource_calc_mult_shift(&cksrc_pxa_oscr0, clock_tick_rate, 4);
> clockevents_calc_mult_shift(&ckevt_pxa_osmr0, clock_tick_rate, 4);
> ckevt_pxa_osmr0.max_delta_ns =
>
>
>
next prev parent reply other threads:[~2011-04-25 16:25 UTC|newest]
Thread overview: 51+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-04-23 20:54 [patch 00/16] arm: Replace arm sched_clock by clocksource based sched_clock Thomas Gleixner
2011-04-23 20:54 ` [patch 01/16] time: Provide clocksource based sched_clock() Thomas Gleixner
2011-04-23 21:33 ` Stephen Boyd
2011-04-23 21:40 ` Thomas Gleixner
2011-04-25 7:10 ` Kukjin Kim
2011-04-26 16:36 ` Stephen Boyd
2011-04-23 20:54 ` [patch 02/16] arm: plat-orion: Use clocksource based sched_clock Thomas Gleixner
2011-04-23 20:54 ` [patch 03/16] arm: s5p: " Thomas Gleixner
2011-04-23 21:33 ` Stephen Boyd
2011-04-23 21:41 ` Thomas Gleixner
2011-04-25 7:08 ` Kukjin Kim
2011-04-23 20:54 ` [patch 04/16] arm: davinci: " Thomas Gleixner
2011-04-26 15:40 ` Nori, Sekhar
2011-04-23 20:54 ` [patch 05/16] arm: ixp4xx: " Thomas Gleixner
2011-04-23 20:54 ` [patch 06/16] arm: mmp: " Thomas Gleixner
2011-04-23 20:54 ` [patch 07/16] arm: omap: " Thomas Gleixner
2011-04-29 11:57 ` Tony Lindgren
2011-04-29 12:28 ` Thomas Gleixner
2011-04-29 12:51 ` Tony Lindgren
2011-04-29 14:19 ` Thomas Gleixner
2011-05-02 8:10 ` Tony Lindgren
2011-04-23 20:54 ` [patch 08/16] arm: pxa: " Thomas Gleixner
2011-04-25 16:25 ` Eric [this message]
2011-04-26 7:23 ` Sascha Hauer
2011-04-26 7:26 ` Eric Miao
2011-04-23 20:54 ` [patch 09/16] arm: sa1100: " Thomas Gleixner
2011-04-23 20:54 ` [patch 10/16] arm: tegra: " Thomas Gleixner
2011-04-23 20:54 ` [patch 11/16] arm: u300: " Thomas Gleixner
2011-04-24 7:03 ` Linus Walleij
2011-04-23 20:54 ` [patch 12/16] arm: plat-iop: " Thomas Gleixner
2011-04-23 20:54 ` [patch 13/16] arm plat-mxc: " Thomas Gleixner
2011-04-26 7:23 ` Sascha Hauer
2011-04-23 20:54 ` [patch 14/16] arm: nomadik: " Thomas Gleixner
2011-04-24 7:04 ` Linus Walleij
2011-04-23 20:54 ` [patch 15/16] arm: versatile: " Thomas Gleixner
2011-04-23 20:54 ` [patch 16/16] arm: Remove sched_clock code Thomas Gleixner
2011-04-25 7:11 ` Kukjin Kim
2011-04-24 7:27 ` [patch 00/16] arm: Replace arm sched_clock by clocksource based sched_clock Linus Walleij
2011-04-25 19:10 ` john stultz
2011-04-26 7:45 ` Linus Walleij
2011-04-26 8:50 ` Tony Lindgren
2011-04-26 8:02 ` Thomas Gleixner
2011-04-29 9:46 ` Russell King - ARM Linux
2011-04-29 10:22 ` Thomas Gleixner
2011-04-29 10:32 ` Tony Lindgren
2011-04-29 17:01 ` Thomas Gleixner
2011-04-29 21:53 ` Linus Walleij
2011-04-29 21:57 ` Thomas Gleixner
2011-05-02 8:18 ` Tony Lindgren
2011-05-08 20:34 ` Linus Walleij
2011-06-13 2:32 ` Rob Herring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=alpine.DEB.2.00.1104260023080.27645@localhost6.localdomain6 \
--to=eric.y.miao@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox