Re: [PATCH v2 3/7] drm/panel: simple: Add waiken WKS101WX001-WCT support

[Frank Li <Frank.li@oss.nxp.com>]

On Thu, Jul 23, 2026 at 10:22:10AM +0800, Liu Ying wrote:
> On Wed, Jul 22, 2026 at 05:12:47PM -0500, Frank Li wrote:
> > On Wed, Jul 22, 2026 at 11:57:09AM +0800, Liu Ying wrote:
> > > On Wed, Jul 22, 2026 at 11:44:09AM +0800, Liu Ying wrote:
> > > > On Tue, Jul 21, 2026 at 07:05:03PM -0500, Frank Li wrote:
> > > > > On Fri, Jul 17, 2026 at 01:48:31PM +0800, Liu Ying wrote:
> > > > > > On Wed, Jul 15, 2026 at 02:34:48PM -0400, Frank.Li@oss.nxp.com wrote:
> > > > > > > From: Frank Li <Frank.Li@nxp.com>
> > > > > > >
> > > > > > > Add support for WKS101WX001-WCT panel, which is an industrial-grade
> > > > > > > 10.1-inch IPS TFT LCD capacitive touch screen display module.
> > > > > > >
> > > > > > > Signed-off-by: Frank Li <Frank.Li@nxp.com>
> > > > > > > ---
> > > > > > > change in v2
> > > > > > > - update height to 135 from 136 (sashiko)
> > > > > > > ---
> > > > > > >  drivers/gpu/drm/panel/panel-simple.c | 31 +++++++++++++++++++++++++++++++
> > > > > > >  1 file changed, 31 insertions(+)
> > > >
> > > > [...]
> > > >
> > > > > > > +	.connector_type = DRM_MODE_CONNECTOR_DPI,
> > > > > >
> > > > > > Seems that the panel also supports LVDS input according to the specification,
> > > > > > since it mentions 'RGB or LVDS Interface'?
> > > > >
> > > > > Need hardware rework to use LVDS. Need remove banch of resistors. Should it
> > > > > be treat as difference panel by different compatible string? hardware
> > > > > actually changed.
> > > >
> > > > Not sure how to handle that.
> > >
> > > Wait, you probably may drop this patch, just document the compatible
> > > string in panel-simple.yaml and panel-lvds.yaml and use add a fallback

panel-simple.yaml don't allow fallback to panel-dpi. Need seperated yaml
for it.

> > > compatible string "panel-dpi" or "panel-lvds" in device tree plus a
> > > panel-timing node.

previous dt-binding discuss, don't allow failback to two compatible string
sorry, I can't remember exactly thread.

like
items:
  - const: ws101w001-wct
  - enum:
       - panel-dpi
       - panel-lvds

> >
> > Look like recently prefer add panel-timing informaiton into c code instead
> > of put it into dts file. But I am not sure about it. Just check recent's
> > log history.
>
> If display timing is specified in panel-simple.c, then you have to specify
> the connector_type there too, right?  The problem here is that you don't
> know the connector_type, as it could be either LVDS or DPI, and I'd assume
> that we don't want two compatible strings - one for LVDS and the other for
> DPI.

If supported both type, generally need customer property and new panel
driver to switch between dpi / lvds

or use
	ports {

		port@0: //connect dpi
		port@1: //connect lvds
	};


I think we can defer this lvds work until it is actually used because
- need a big hardware rework to support lvds, most likely it will not be
appeared at real productions. If it mass production, vendor most likely use
difference module number for it.
- it may be end of life if there are not much users.

Frank

> Although display timing in panel-simple.c avoids duplicated panel-timing
> nodes across various potential DT files, I think you have the "good" reason
> here to use the panel-timing node + fallback compatible string with one single
> panel specific compatible string.
>
> >
> > Add Neil Armstrong for comments.
> >
> > Frank
> >
> > >
> > > --
> > > Regards,
> > > Liu Ying
>
> --
> Regards,
> Liu Ying