From: Frank Li <Frank.li@oss.nxp.com>
To: vjardin@free.fr
Cc: Dong Aisheng <aisheng.dong@nxp.com>,
Fabio Estevam <festevam@gmail.com>, Frank Li <Frank.Li@nxp.com>,
Jacky Bai <ping.bai@nxp.com>,
Pengutronix Kernel Team <kernel@pengutronix.de>,
NXP S32 Linux Team <s32@nxp.com>,
Linus Walleij <linusw@kernel.org>, Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
"Christophe Leroy (CS GROUP)" <chleroy@kernel.org>,
Shawn Guo <shawnguo@kernel.org>,
Sascha Hauer <s.hauer@pengutronix.de>,
linux-gpio@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, linuxppc-dev@lists.ozlabs.org,
linux-arm-kernel@lists.infradead.org, imx@lists.linux.dev,
Vladimir Oltean <vladimir.oltean@nxp.com>,
Ioana Ciornei <ioana.ciornei@nxp.com>
Subject: Re: [PATCH v6 4/5] pinctrl: freescale: add the Layerscape RCW pad-mux driver
Date: Mon, 16 Nov 2026 11:12:22 -0600 [thread overview]
Message-ID: <avs5doXCSvucsOdR@SMW015318> (raw)
In-Reply-To: <20261115-for-upstream-lx2160a-rcw-pinmux-v1-v6-4-fbdce4565a5c@free.fr>
On Sun, Nov 15, 2026 at 02:27:34PM +0100, Vincent Jardin via B4 Relay wrote:
> From: Vincent Jardin <vjardin@free.fr>
>
> The LX2160A muxes its IIC, XSPI, SDHC, UART, IRQ and EVT pads from
> fields of the RCW, read-only in RCWSR12..14 of DCFG and changed at
> runtime through the same fields of the override registers in its DCSR
> view, which read 0 until written.
>
> Since commit 8a1365c7bbc1 ("arm64: dts: lx2160a: add pinmux and i2c
> gpio to support bus recovery") Linux drives them with pinctrl-single on
> the override registers, so its first pin state clears every other field
> of the word: a board whose RCW programs a non-zero pad mux loses those
> pads at the first I2C probe.
>
> Add a generic Layerscape driver for the pad mux as a child of the DCFG
> node. The fields and their encoding are per-SoC tables selected by
> the compatible, so that other Layerscape SoCs can be added to it.
>
> Only the LX2160A is done: the fields of RCWSR12..14 and the EC1, EC2,
> USB_EXT, GTX_CLK and SDHC1_DS ones of RCWSR27.
>
> Then pin states select them with the generic function and groups
> properties, and every change goes through the RCW override
> of fsl-guts, which reads the status register, writes the override and
> waits for the status register to follow.
>
> Signed-off-by: Vincent Jardin <vjardin@free.fr>
> ---
Reviewed-by: Frank Li <Frank.Li@nxp.com>
> MAINTAINERS | 8 +
> drivers/pinctrl/freescale/Kconfig | 15 +
> drivers/pinctrl/freescale/Makefile | 1 +
> drivers/pinctrl/freescale/pinctrl-layerscape-rcw.c | 427 +++++++++++++++++++++
> 4 files changed, 451 insertions(+)
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 93abbb315065..2df4866d37bb 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -20207,6 +20207,14 @@ F: Documentation/devicetree/bindings/clock/*imx*
> F: drivers/clk/imx/
> F: include/dt-bindings/clock/*imx*
>
> +NXP LAYERSCAPE RCW PAD-MUX DRIVER
> +M: Vincent Jardin <vjardin@free.fr>
> +L: linux-gpio@vger.kernel.org
> +L: imx@lists.linux.dev
> +S: Maintained
> +F: Documentation/devicetree/bindings/pinctrl/fsl,lx2160a-rcw-pinmux.yaml
> +F: drivers/pinctrl/freescale/pinctrl-layerscape-rcw.c
> +
> NXP NETC ETHERNET SWITCH DRIVER
> M: Wei Fang <wei.fang@nxp.com>
> R: Clark Wang <xiaoning.wang@nxp.com>
> diff --git a/drivers/pinctrl/freescale/Kconfig b/drivers/pinctrl/freescale/Kconfig
> index fd53cf5bb843..8e964cf620b0 100644
> --- a/drivers/pinctrl/freescale/Kconfig
> +++ b/drivers/pinctrl/freescale/Kconfig
> @@ -283,3 +283,18 @@ config PINCTRL_IMXRT1170
> select PINCTRL_IMX
> help
> Say Y here to enable the imxrt1170 pinctrl driver
> +
> +config PINCTRL_LAYERSCAPE_RCW
> + bool "NXP Layerscape RCW pad-mux driver"
> + depends on OF
> + depends on ARCH_LAYERSCAPE || COMPILE_TEST
> + default ARCH_LAYERSCAPE
> + select FSL_GUTS
> + select GENERIC_PINCTRL_GROUPS
> + select GENERIC_PINMUX_FUNCTIONS
> + select GENERIC_PINCONF
> + help
> + Say Y here to mux the pads of the Layerscape SoCs at runtime. The
> + pads are muxed by fields of the RCW: the driver changes it in the
> + DCSR view of the DCFG that fsl-guts drives.
> + The I2C bus recovery needs it to switch the pads of a bus to GPIO.
> diff --git a/drivers/pinctrl/freescale/Makefile b/drivers/pinctrl/freescale/Makefile
> index d27085c2b4c4..34309ac7411d 100644
> --- a/drivers/pinctrl/freescale/Makefile
> +++ b/drivers/pinctrl/freescale/Makefile
> @@ -35,3 +35,4 @@ obj-$(CONFIG_PINCTRL_IMX25) += pinctrl-imx25.o
> obj-$(CONFIG_PINCTRL_IMX28) += pinctrl-imx28.o
> obj-$(CONFIG_PINCTRL_IMXRT1050) += pinctrl-imxrt1050.o
> obj-$(CONFIG_PINCTRL_IMXRT1170) += pinctrl-imxrt1170.o
> +obj-$(CONFIG_PINCTRL_LAYERSCAPE_RCW) += pinctrl-layerscape-rcw.o
> diff --git a/drivers/pinctrl/freescale/pinctrl-layerscape-rcw.c b/drivers/pinctrl/freescale/pinctrl-layerscape-rcw.c
> new file mode 100644
> index 000000000000..46686c6923c3
> --- /dev/null
> +++ b/drivers/pinctrl/freescale/pinctrl-layerscape-rcw.c
> @@ -0,0 +1,427 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Layerscape pad muxes: fields of the RCW, changed at runtime.
> + *
> + * Copyright 2026 Free Mobile - Vincent Jardin
> + */
> +
> +#include <linux/bitfield.h>
> +#include <linux/bits.h>
> +#include <linux/fsl/guts.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/pinctrl/pinconf-generic.h>
> +#include <linux/pinctrl/pinctrl.h>
> +#include <linux/pinctrl/pinmux.h>
> +#include <linux/platform_device.h>
> +#include <linux/property.h>
> +#include <linux/seq_file.h>
> +
> +#include "../core.h"
> +#include "../pinmux.h"
> +
> +struct rcw_pmux_func {
> + const char *name;
> + u8 val;
> +};
> +
> +struct rcw_pmux_group {
> + const char *name;
> + u8 rcwsr; /* one-based, as in RCWSR12 */
> + u8 shift;
> + u8 width;
> + const struct rcw_pmux_func *funcs;
> + u8 nfuncs;
> +};
> +
> +/* The pad-mux groups of a SoC, one per field of its RCW */
> +struct rcw_pmux_soc {
> + const struct rcw_pmux_group *groups;
> + unsigned int ngroups;
> +};
> +
> +#define RCW_PMUX_FUNC(_name, _val) { .name = _name, .val = _val }
> +#define RCW_PMUX_GROUP(_name, _rcwsr, _shift, _width, _funcs) \
> + { \
> + .name = _name, .rcwsr = _rcwsr, \
> + .shift = _shift, .width = _width, \
> + .funcs = _funcs, .nfuncs = ARRAY_SIZE(_funcs), \
> + }
> +
> +/* LX2160A: RCWSR12..14 and RCWSR27 */
> +static const struct rcw_pmux_func lx2160a_iic2_funcs[] = {
> + RCW_PMUX_FUNC("i2c", 0), RCW_PMUX_FUNC("gpio", 1),
> + RCW_PMUX_FUNC("flextimer", 2), RCW_PMUX_FUNC("sdhc", 6),
> +};
> +
> +static const struct rcw_pmux_func lx2160a_iic3_funcs[] = {
> + RCW_PMUX_FUNC("i2c", 0), RCW_PMUX_FUNC("gpio", 1),
> + RCW_PMUX_FUNC("can", 2), RCW_PMUX_FUNC("evt", 6),
> +};
> +
> +static const struct rcw_pmux_func lx2160a_iic5_funcs[] = {
> + RCW_PMUX_FUNC("i2c", 0), RCW_PMUX_FUNC("gpio", 1),
> + RCW_PMUX_FUNC("sdhc-clk", 2), RCW_PMUX_FUNC("spi", 3),
> +};
> +
> +static const struct rcw_pmux_func lx2160a_iic6_funcs[] = {
> + RCW_PMUX_FUNC("i2c", 0), RCW_PMUX_FUNC("gpio", 1),
> + RCW_PMUX_FUNC("sdhc-clk", 2),
> +};
> +
> +static const struct rcw_pmux_func lx2160a_xspi1_funcs[] = {
> + RCW_PMUX_FUNC("flexspi", 0), RCW_PMUX_FUNC("gpio", 1),
> +};
> +
> +static const struct rcw_pmux_func lx2160a_sdhc1_base_funcs[] = {
> + RCW_PMUX_FUNC("sdhc", 0), RCW_PMUX_FUNC("gpio", 1),
> + RCW_PMUX_FUNC("spi", 2), RCW_PMUX_FUNC("sdhc-spi", 3),
> + RCW_PMUX_FUNC("sdhc-data4", 4),
> +};
> +
> +static const struct rcw_pmux_func lx2160a_sdhc1_dir_funcs[] = {
> + RCW_PMUX_FUNC("sdhc", 0), RCW_PMUX_FUNC("gpio", 1),
> + RCW_PMUX_FUNC("spi", 3), RCW_PMUX_FUNC("sdhc-data", 4),
> +};
> +
> +static const struct rcw_pmux_func lx2160a_sdhc2_data74_funcs[] = {
> + RCW_PMUX_FUNC("sdhc", 0), RCW_PMUX_FUNC("gpio", 1),
> + RCW_PMUX_FUNC("i2c", 2), RCW_PMUX_FUNC("flexspi", 6),
> +};
> +
> +static const struct rcw_pmux_func lx2160a_sdhc2_base_funcs[] = {
> + RCW_PMUX_FUNC("sdhc", 0), RCW_PMUX_FUNC("gpio", 1),
> + RCW_PMUX_FUNC("spi", 2), RCW_PMUX_FUNC("flexspi", 6),
> +};
> +
> +static const struct rcw_pmux_func lx2160a_uart_funcs[] = {
> + RCW_PMUX_FUNC("uart", 0), RCW_PMUX_FUNC("gpio", 1),
> +};
> +
> +static const struct rcw_pmux_func lx2160a_uart1_rtscts_funcs[] = {
> + RCW_PMUX_FUNC("uart", 0), RCW_PMUX_FUNC("gpio", 1),
> + RCW_PMUX_FUNC("uart3", 2),
> +};
> +
> +static const struct rcw_pmux_func lx2160a_uart2_rtscts_funcs[] = {
> + RCW_PMUX_FUNC("uart", 0), RCW_PMUX_FUNC("gpio", 1),
> + RCW_PMUX_FUNC("uart4", 2),
> +};
> +
> +static const struct rcw_pmux_func lx2160a_irq_funcs[] = {
> + RCW_PMUX_FUNC("irq", 0), RCW_PMUX_FUNC("gpio", 1),
> +};
> +
> +static const struct rcw_pmux_func lx2160a_irq_flextimer_funcs[] = {
> + RCW_PMUX_FUNC("irq", 0), RCW_PMUX_FUNC("gpio", 1),
> + RCW_PMUX_FUNC("flextimer", 2),
> +};
> +
> +static const struct rcw_pmux_func lx2160a_evt_funcs[] = {
> + RCW_PMUX_FUNC("evt", 0), RCW_PMUX_FUNC("gpio", 1),
> + RCW_PMUX_FUNC("flextimer", 2),
> +};
> +
> +static const struct rcw_pmux_func lx2160a_clk_out_funcs[] = {
> + RCW_PMUX_FUNC("gpio", 1), RCW_PMUX_FUNC("flextimer", 2),
> +};
> +
> +static const struct rcw_pmux_func lx2160a_asleep_funcs[] = {
> + RCW_PMUX_FUNC("asleep", 0), RCW_PMUX_FUNC("gpio", 1),
> + RCW_PMUX_FUNC("evt", 2),
> +};
> +
> +static const struct rcw_pmux_func lx2160a_reset_req_funcs[] = {
> + RCW_PMUX_FUNC("reset-req", 0), RCW_PMUX_FUNC("gpio", 1),
> +};
> +
> +static const struct rcw_pmux_func lx2160a_iic1_funcs[] = {
> + RCW_PMUX_FUNC("i2c", 0), RCW_PMUX_FUNC("gpio", 1),
> +};
> +
> +static const struct rcw_pmux_func lx2160a_ec1_funcs[] = {
> + RCW_PMUX_FUNC("rgmii", 0), RCW_PMUX_FUNC("gpio", 1),
> +};
> +
> +static const struct rcw_pmux_func lx2160a_ec2_funcs[] = {
> + RCW_PMUX_FUNC("rgmii", 0), RCW_PMUX_FUNC("gpio", 1),
> + RCW_PMUX_FUNC("tsec-1588", 2),
> +};
> +
> +static const struct rcw_pmux_func lx2160a_usb_ext_funcs[] = {
> + RCW_PMUX_FUNC("usb", 0), RCW_PMUX_FUNC("gpio", 1),
> +};
> +
> +static const struct rcw_pmux_func lx2160a_gtx_clk_funcs[] = {
> + RCW_PMUX_FUNC("gtx-clk", 0), RCW_PMUX_FUNC("gpio", 1),
> +};
> +
> +static const struct rcw_pmux_func lx2160a_sdhc1_ds_funcs[] = {
> + RCW_PMUX_FUNC("sdhc", 0), RCW_PMUX_FUNC("gpio", 1),
> + RCW_PMUX_FUNC("spi", 2),
> +};
> +
> +static const struct rcw_pmux_group lx2160a_groups[] = {
> + /* RCWSR12 */
> + RCW_PMUX_GROUP("iic2", 12, 0, 3, lx2160a_iic2_funcs),
> + RCW_PMUX_GROUP("iic3", 12, 3, 3, lx2160a_iic3_funcs),
> + RCW_PMUX_GROUP("iic4", 12, 6, 3, lx2160a_iic3_funcs),
> + RCW_PMUX_GROUP("iic5", 12, 9, 3, lx2160a_iic5_funcs),
> + RCW_PMUX_GROUP("iic6", 12, 12, 3, lx2160a_iic6_funcs),
> + RCW_PMUX_GROUP("xspi1-data74", 12, 15, 3, lx2160a_xspi1_funcs),
> + RCW_PMUX_GROUP("xspi1-data30", 12, 18, 3, lx2160a_xspi1_funcs),
> + RCW_PMUX_GROUP("xspi1-base", 12, 21, 3, lx2160a_xspi1_funcs),
> + RCW_PMUX_GROUP("sdhc1-base", 12, 24, 3, lx2160a_sdhc1_base_funcs),
> + RCW_PMUX_GROUP("sdhc1-dir", 12, 27, 3, lx2160a_sdhc1_dir_funcs),
> + /* RCWSR13 */
> + RCW_PMUX_GROUP("sdhc2-data74", 13, 0, 3, lx2160a_sdhc2_data74_funcs),
> + RCW_PMUX_GROUP("sdhc2-base", 13, 3, 3, lx2160a_sdhc2_base_funcs),
> + RCW_PMUX_GROUP("uart1-soutsin", 13, 6, 3, lx2160a_uart_funcs),
> + RCW_PMUX_GROUP("uart1-rtscts", 13, 9, 3, lx2160a_uart1_rtscts_funcs),
> + RCW_PMUX_GROUP("uart2-soutsin", 13, 12, 3, lx2160a_uart_funcs),
> + RCW_PMUX_GROUP("uart2-rtscts", 13, 15, 3, lx2160a_uart2_rtscts_funcs),
> + RCW_PMUX_GROUP("irq11-8", 13, 18, 3, lx2160a_irq_funcs),
> + RCW_PMUX_GROUP("irq7-4", 13, 21, 3, lx2160a_irq_flextimer_funcs),
> + RCW_PMUX_GROUP("irq3-0", 13, 24, 3, lx2160a_irq_flextimer_funcs),
> + RCW_PMUX_GROUP("evt4-3", 13, 27, 3, lx2160a_evt_funcs),
> + /* RCWSR14 */
> + RCW_PMUX_GROUP("evt2-0", 14, 0, 3, lx2160a_evt_funcs),
> + RCW_PMUX_GROUP("clk-out", 14, 3, 3, lx2160a_clk_out_funcs),
> + RCW_PMUX_GROUP("asleep", 14, 6, 3, lx2160a_asleep_funcs),
> + RCW_PMUX_GROUP("reset-req", 14, 9, 1, lx2160a_reset_req_funcs),
> + RCW_PMUX_GROUP("iic1", 14, 10, 1, lx2160a_iic1_funcs),
> + /* RCWSR27 */
> + RCW_PMUX_GROUP("ec1", 27, 0, 2, lx2160a_ec1_funcs),
> + RCW_PMUX_GROUP("ec2", 27, 2, 2, lx2160a_ec2_funcs),
> + RCW_PMUX_GROUP("usb-ext", 27, 4, 1, lx2160a_usb_ext_funcs),
> + RCW_PMUX_GROUP("gtx-clk", 27, 5, 1, lx2160a_gtx_clk_funcs),
> + RCW_PMUX_GROUP("sdhc1-ds", 27, 6, 2, lx2160a_sdhc1_ds_funcs),
> +};
> +
> +static const struct rcw_pmux_soc lx2160a_soc = {
> + .groups = lx2160a_groups,
> + .ngroups = ARRAY_SIZE(lx2160a_groups),
> +};
> +
> +struct rcw_pmux {
> + struct device *dev;
> + struct pinctrl_dev *pctl;
> + struct pinctrl_desc desc;
> + const struct rcw_pmux_soc *soc;
> + struct pinctrl_pin_desc *pins;
> +};
> +
> +static u32 rcw_pmux_group_mask(const struct rcw_pmux_group *group)
> +{
> + return GENMASK(group->shift + group->width - 1, group->shift);
> +}
> +
> +static const struct rcw_pmux_func *
> +rcw_pmux_find_func(const struct rcw_pmux_group *group, const char *name)
> +{
> + unsigned int i;
> +
> + for (i = 0; i < group->nfuncs; i++) {
> + if (!strcmp(group->funcs[i].name, name))
> + return &group->funcs[i];
> + }
> +
> + return NULL;
> +}
> +
> +static void rcw_pmux_pin_dbg_show(struct pinctrl_dev *pctldev,
> + struct seq_file *s, unsigned int pin)
> +{
> + struct rcw_pmux *pmux = pinctrl_dev_get_drvdata(pctldev);
> + const struct rcw_pmux_group *group = &pmux->soc->groups[pin];
> + unsigned int i;
> + u32 val;
> +
> + if (fsl_guts_pmux_read(group->rcwsr, &val))
> + return;
> +
> + val = field_get(rcw_pmux_group_mask(group), val);
> + for (i = 0; i < group->nfuncs; i++) {
> + if (group->funcs[i].val == val) {
> + seq_puts(s, group->funcs[i].name);
> + return;
> + }
> + }
> + seq_printf(s, "0x%x", val);
> +}
> +
> +static const struct pinctrl_ops rcw_pmux_pctlops = {
> + .get_groups_count = pinctrl_generic_get_group_count,
> + .get_group_name = pinctrl_generic_get_group_name,
> + .get_group_pins = pinctrl_generic_get_group_pins,
> + .pin_dbg_show = rcw_pmux_pin_dbg_show,
> + .dt_node_to_map = pinconf_generic_dt_node_to_map_group,
> + .dt_free_map = pinconf_generic_dt_free_map,
> +};
> +
> +static int rcw_pmux_set_mux(struct pinctrl_dev *pctldev,
> + unsigned int fsel, unsigned int gsel)
> +{
> + struct rcw_pmux *pmux = pinctrl_dev_get_drvdata(pctldev);
> + const struct function_desc *func;
> + const struct rcw_pmux_group *group;
> + const struct rcw_pmux_func *mux;
> + const struct group_desc *grp;
> + u32 mask;
> +
> + func = pinmux_generic_get_function(pctldev, fsel);
> + grp = pinctrl_generic_get_group(pctldev, gsel);
> + if (!func || !grp)
> + return -EINVAL;
> + group = grp->data;
> +
> + mux = rcw_pmux_find_func(group, func->func->name);
> + if (!mux) {
> + dev_err(pmux->dev, "%s has no %s function\n",
> + group->name, func->func->name);
> + return -EINVAL;
> + }
> +
> + mask = rcw_pmux_group_mask(group);
> +
> + return fsl_guts_pmux_override(group->rcwsr, field_prep(mask, mux->val),
> + mask);
> +}
> +
> +static const struct pinmux_ops rcw_pmux_pmxops = {
> + .get_functions_count = pinmux_generic_get_function_count,
> + .get_function_name = pinmux_generic_get_function_name,
> + .get_function_groups = pinmux_generic_get_function_groups,
> + .set_mux = rcw_pmux_set_mux,
> + .strict = true,
> +};
> +
> +static int rcw_pmux_add_functions(struct rcw_pmux *pmux)
> +{
> + const struct rcw_pmux_soc *soc = pmux->soc;
> + const struct rcw_pmux_group *group;
> + const char **groups;
> + unsigned int i, j, k, n;
> + int ret;
> +
> + for (i = 0; i < soc->ngroups; i++) {
> + group = &soc->groups[i];
> + for (j = 0; j < group->nfuncs; j++) {
> + const char *name = group->funcs[j].name;
> +
> + /* already added from an earlier group? */
> + for (k = 0; k < i; k++) {
> + if (rcw_pmux_find_func(&soc->groups[k], name))
> + break;
> + }
> + if (k < i)
> + continue;
> +
> + groups = devm_kcalloc(pmux->dev, soc->ngroups,
> + sizeof(*groups), GFP_KERNEL);
> + if (!groups)
> + return -ENOMEM;
> + n = 0;
> + for (k = i; k < soc->ngroups; k++) {
> + if (rcw_pmux_find_func(&soc->groups[k], name))
> + groups[n++] = soc->groups[k].name;
> + }
> + ret = pinmux_generic_add_function(pmux->pctl, name,
> + groups, n, NULL);
> + if (ret < 0)
> + return ret;
> + }
> + }
> +
> + return 0;
> +}
> +
> +static int rcw_pmux_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + const struct rcw_pmux_soc *soc;
> + struct rcw_pmux *pmux;
> + unsigned int i;
> + u32 val;
> + int ret;
> +
> + /* The override needs the DCSR view of DCFG, mapped by fsl-guts */
> + if (!fsl_guts_pmux_override_supported())
> + return dev_err_probe(dev, -ENODEV,
> + "no RCW override through fsl-guts: the dcfg node needs its DCSR reg\n");
> +
> + soc = device_get_match_data(dev);
> + if (!soc)
> + return -ENODEV;
> +
> + pmux = devm_kzalloc(dev, sizeof(*pmux), GFP_KERNEL);
> + if (!pmux)
> + return -ENOMEM;
> + pmux->dev = dev;
> + pmux->soc = soc;
> +
> + pmux->pins = devm_kcalloc(dev, soc->ngroups, sizeof(*pmux->pins),
> + GFP_KERNEL);
> + if (!pmux->pins)
> + return -ENOMEM;
> +
> + for (i = 0; i < soc->ngroups; i++) {
> + pmux->pins[i].number = i;
> + pmux->pins[i].name = soc->groups[i].name;
> + }
> + pmux->desc.name = dev_name(dev);
> + pmux->desc.pins = pmux->pins;
> + pmux->desc.npins = soc->ngroups;
> + pmux->desc.pctlops = &rcw_pmux_pctlops;
> + pmux->desc.pmxops = &rcw_pmux_pmxops;
> + pmux->desc.owner = THIS_MODULE;
> +
> + ret = devm_pinctrl_register_and_init(dev, &pmux->desc, pmux,
> + &pmux->pctl);
> + if (ret)
> + return dev_err_probe(dev, ret, "pinctrl registration failed\n");
> +
> + for (i = 0; i < soc->ngroups; i++) {
> + ret = pinctrl_generic_add_group(pmux->pctl, soc->groups[i].name,
> + &pmux->pins[i].number, 1,
> + (void *)&soc->groups[i]);
> + if (ret < 0)
> + return ret;
> + }
> +
> + ret = rcw_pmux_add_functions(pmux);
> + if (ret)
> + return ret;
> +
> + for (i = 0; i < soc->ngroups; i++) {
> + u8 rcwsr = soc->groups[i].rcwsr;
> +
> + if (i && rcwsr == soc->groups[i - 1].rcwsr)
> + continue;
> + if (!fsl_guts_pmux_read(rcwsr, &val))
> + dev_dbg(dev, "pad muxes of RCWSR%u = 0x%08x\n", rcwsr,
> + val);
> + }
> +
> + return pinctrl_enable(pmux->pctl);
> +}
> +
> +static const struct of_device_id rcw_pmux_of_match[] = {
> + { .compatible = "fsl,lx2160a-rcw-pinmux", .data = &lx2160a_soc },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, rcw_pmux_of_match);
> +
> +static struct platform_driver rcw_pmux_driver = {
> + .driver = {
> + .name = "layerscape-rcw-pinmux",
> + .of_match_table = rcw_pmux_of_match,
> + },
> + .probe = rcw_pmux_probe,
> +};
> +module_platform_driver(rcw_pmux_driver);
> +
> +MODULE_AUTHOR("Vincent Jardin <vjardin@free.fr>");
> +MODULE_DESCRIPTION("NXP Layerscape RCW pad-mux driver");
> +MODULE_LICENSE("GPL");
> +MODULE_IMPORT_NS("FSL_GUTS");
>
> --
> 2.43.0
>
>
>
next prev parent reply other threads:[~2026-11-16 17:12 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-15 13:27 [PATCH v6 0/5] lx2160a: change the pad muxes through the RCW override Vincent Jardin via B4 Relay
2026-11-15 13:27 ` [PATCH v6 1/5] dt-bindings: pinctrl: add the NXP LX2160A RCW pad mux Vincent Jardin via B4 Relay
2026-11-16 17:02 ` Frank Li
2026-11-15 13:27 ` [PATCH v6 2/5] dt-bindings: soc: fsl: layerscape-dcfg: add the LX2160A pad-mux child Vincent Jardin via B4 Relay
2026-11-16 17:04 ` Frank Li
2026-11-15 13:27 ` [PATCH v6 3/5] soc: fsl: guts: add the RCW override of the pad muxes Vincent Jardin via B4 Relay
2026-11-16 17:08 ` Frank Li
2026-11-15 13:27 ` [PATCH v6 4/5] pinctrl: freescale: add the Layerscape RCW pad-mux driver Vincent Jardin via B4 Relay
2026-11-16 17:12 ` Frank Li [this message]
2026-11-15 13:27 ` [PATCH v6 5/5] arm64: dts: lx2160a: describe the pad muxes as the DCFG RCW override Vincent Jardin via B4 Relay
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=avs5doXCSvucsOdR@SMW015318 \
--to=frank.li@oss.nxp.com \
--cc=Frank.Li@nxp.com \
--cc=aisheng.dong@nxp.com \
--cc=chleroy@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=festevam@gmail.com \
--cc=imx@lists.linux.dev \
--cc=ioana.ciornei@nxp.com \
--cc=kernel@pengutronix.de \
--cc=krzk+dt@kernel.org \
--cc=linusw@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linuxppc-dev@lists.ozlabs.org \
--cc=ping.bai@nxp.com \
--cc=robh@kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=s32@nxp.com \
--cc=shawnguo@kernel.org \
--cc=vjardin@free.fr \
--cc=vladimir.oltean@nxp.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox