From: Marcus Folkesson <marcus.folkesson@gmail.com>
To: Wolfram Sang <wsa+renesas@sang-engineering.com>,
Michael Hennerich <michael.hennerich@analog.com>,
Bartosz Golaszewski <brgl@bgdev.pl>,
Andi Shyti <andi.shyti@kernel.org>,
Andy Shevchenko <andriy.shevchenko@intel.com>,
Bartosz Golaszewski <brgl@kernel.org>,
Peter Rosin <peda@lysator.liu.se>
Cc: linux-i2c@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH v13 0/8] I2C Mux per channel bus speed
Date: Fri, 20 Nov 2026 12:29:07 +0100 [thread overview]
Message-ID: <awAvA1rSGwh0RaIW@gmail.com> (raw)
In-Reply-To: <20261015-i2c-mux-v13-0-778a12cfe93b@gmail.com>
On Thu, Oct 15, 2026 at 01:01:47PM +0200, Marcus Folkesson wrote:
> This was a RFC on how to implement a feature to have different bus
> speeds on different channels with an I2C multiplexer/switch.
> As no major complaints on the design came up during the review, I
> decided to submit the series without the RFC tag.
>
> The benefit with this feature is that you may group devices after
> the fastest bus speed they can handle.
> A real-world example is that you could have e.g. a display running @400kHz
> and a smart battery running @100kHz using the same I2C controller.
>
> There are many corner cases where this may cause a problem for some
> hardware topologies. I've tried to describe those I could think of
> in the documentation, see Patch #5.
>
> E.g. one risk is that if the mux driver does not disconnect channels
> when Idle, this may cause a higher frequency to "leak" through to
> devices that are supposed to run at lower bus speed.
> This is not only a "problem" for changing bus speed but could also be
> an issue for potential address conflicts.
>
> This patchset has been used and tested heavily the last months
> on a custom board based on a da850 (DaVinci) platform.
>
> The implementation is split up into several patches:
>
> Patch #1 Introduce a callback for the i2c controller to set bus speed
> Patch #2 Introduce functionality to adjust bus speed depending on mux
> channel.
> Patch #3 Cleanup i2c-davinci driver a bit to prepare it for set_clk_freq
> Parch #4 Implement set_clk_freq for the i2c-davinci driver
> Parch #5 Update documentation with this feature
>
> Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
> ---
Gently ping on this series.
Thanks,
Marcus Folkesson
prev parent reply other threads:[~2026-11-20 11:29 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-10-15 11:01 [PATCH v13 0/8] I2C Mux per channel bus speed Marcus Folkesson
2026-10-15 11:01 ` [PATCH v13 1/8] i2c: core: add callback to change bus frequency Marcus Folkesson
2026-10-15 11:01 ` [PATCH v13 2/8] i2c: mux: add idle_state property to i2c_mux_core Marcus Folkesson
2026-10-15 11:01 ` [PATCH v13 3/8] i2c: mux: add support for per channel bus frequency Marcus Folkesson
2026-10-15 11:01 ` [PATCH v13 4/8] i2c: davinci: calculate bus freq from Hz instead of kHz Marcus Folkesson
2026-10-15 11:01 ` [PATCH v13 5/8] i2c: davinci: add support for setting bus frequency Marcus Folkesson
2026-10-15 11:01 ` [PATCH v13 6/8] i2c: mux: ltc4306: set correct idle_state in i2c_mux_core Marcus Folkesson
2026-10-15 11:01 ` [PATCH v13 7/8] docs: i2c: i2c-topology: add section about bus speed Marcus Folkesson
2026-10-15 11:01 ` [PATCH v13 8/8] i2c: mux: pca954x: use idle state from i2c_mux_core Marcus Folkesson
2026-11-20 11:29 ` Marcus Folkesson [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=awAvA1rSGwh0RaIW@gmail.com \
--to=marcus.folkesson@gmail.com \
--cc=andi.shyti@kernel.org \
--cc=andriy.shevchenko@intel.com \
--cc=brgl@bgdev.pl \
--cc=brgl@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-i2c@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=michael.hennerich@analog.com \
--cc=peda@lysator.liu.se \
--cc=wsa+renesas@sang-engineering.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox