From: viresh.kumar@linaro.org (Viresh Kumar)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 08/14] ARM: SPEAr: DT: Update device nodes
Date: Sun, 11 Nov 2012 10:09:30 +0530 [thread overview]
Message-ID: <b3925b105ee2c6fe828ef3b54928aeee02a801ae.1352608333.git.viresh.kumar@linaro.org> (raw)
In-Reply-To: <cover.1352608333.git.viresh.kumar@linaro.org>
From: Shiraz Hashim <shiraz.hashim@st.com>
This patch adds multiple device nodes for SPEAr machines and boards.
Signed-off-by: Bhavna Yadav <bhavna.yadav@st.com>
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Vijay Kumar Mishra <vijay.kumar@st.com>
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
---
arch/arm/boot/dts/spear1310-evb.dts | 89 +++++++++++++++++++
arch/arm/boot/dts/spear1310.dtsi | 2 +
arch/arm/boot/dts/spear1340-evb.dts | 172 ++++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/spear1340.dtsi | 46 ++++++++++
arch/arm/boot/dts/spear13xx.dtsi | 39 ++++++++
arch/arm/boot/dts/spear320.dtsi | 11 +++
arch/arm/boot/dts/spear3xx.dtsi | 2 +
arch/arm/boot/dts/spear600-evb.dts | 24 +++++
arch/arm/boot/dts/spear600.dtsi | 15 ++++
9 files changed, 400 insertions(+)
diff --git a/arch/arm/boot/dts/spear1310-evb.dts b/arch/arm/boot/dts/spear1310-evb.dts
index c60c3f8..56ea6d5 100644
--- a/arch/arm/boot/dts/spear1310-evb.dts
+++ b/arch/arm/boot/dts/spear1310-evb.dts
@@ -147,6 +147,20 @@
};
};
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ button at 1 {
+ label = "wakeup";
+ linux,code = <0x100>;
+ gpios = <&gpio0 7 0x4>;
+ debounce-interval = <20>;
+ gpio-key,wakeup = <1>;
+ };
+ };
+
gmac0: eth at e2000000 {
phy-mode = "gmii";
status = "okay";
@@ -326,6 +340,81 @@
spi0: spi at e0100000 {
status = "okay";
+ num-cs = <3>;
+ cs-gpios = <&gpio1 7 0>, <&spics 0>, <&spics 1>;
+
+ stmpe610 at 0 {
+ status = "okay";
+ compatible = "st,stmpe610";
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ spi-max-frequency = <1000000>;
+ spi-cpha;
+ pl022,hierarchy = <0>;
+ pl022,interface = <0>;
+ pl022,slave-tx-disable;
+ pl022,com-mode = <0>;
+ pl022,rx-level-trig = <0>;
+ pl022,tx-level-trig = <0>;
+ pl022,ctrl-len = <0x7>;
+ pl022,wait-state = <0>;
+ pl022,duplex = <0>;
+ id = <0>;
+ blocks = <4>;
+ irq_over_gpio;
+ irq-gpios = <&gpio1 6 0x4>;
+ irq-trigger = <0x2>;
+
+ stmpe610-ts {
+ compatible = "stmpe,ts";
+ reg = <0>;
+ ts,sample-time = <4>;
+ ts,mod-12b = <1>;
+ ts,ref-sel = <0>;
+ ts,adc-freq = <1>;
+ ts,ave-ctrl = <1>;
+ ts,touch-det-delay = <2>;
+ ts,settling = <2>;
+ ts,fraction-z = <7>;
+ ts,i-drive = <1>;
+ };
+ };
+
+ m25p80 at 1 {
+ status = "okay";
+ compatible = "st,m25p80";
+ reg = <1>;
+ spi-max-frequency = <12000000>;
+ spi-cpol;
+ spi-cpha;
+ pl022,hierarchy = <0>;
+ pl022,interface = <0>;
+ pl022,slave-tx-disable;
+ pl022,com-mode = <0x2>;
+ pl022,rx-level-trig = <0>;
+ pl022,tx-level-trig = <0>;
+ pl022,ctrl-len = <0x11>;
+ pl022,wait-state = <0>;
+ pl022,duplex = <0>;
+ };
+
+ spidev at 2 {
+ status = "okay";
+ compatible = "spidev";
+ reg = <2>;
+ spi-max-frequency = <25000000>;
+ spi-cpha;
+ pl022,hierarchy = <0>;
+ pl022,interface = <0>;
+ pl022,slave-tx-disable;
+ pl022,com-mode = <0x2>;
+ pl022,rx-level-trig = <0>;
+ pl022,tx-level-trig = <0>;
+ pl022,ctrl-len = <0x11>;
+ pl022,wait-state = <0>;
+ pl022,duplex = <0>;
+ };
};
wdt at ec800620 {
diff --git a/arch/arm/boot/dts/spear1310.dtsi b/arch/arm/boot/dts/spear1310.dtsi
index bd6b64b..8fb22b9 100644
--- a/arch/arm/boot/dts/spear1310.dtsi
+++ b/arch/arm/boot/dts/spear1310.dtsi
@@ -154,6 +154,8 @@
compatible = "arm,pl022", "arm,primecell";
reg = <0x5d400000 0x1000>;
interrupts = <0 99 0x4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
status = "disabled";
};
diff --git a/arch/arm/boot/dts/spear1340-evb.dts b/arch/arm/boot/dts/spear1340-evb.dts
index c6051dd..c0a3677 100644
--- a/arch/arm/boot/dts/spear1340-evb.dts
+++ b/arch/arm/boot/dts/spear1340-evb.dts
@@ -118,6 +118,10 @@
};
};
+ ahci at b1000000 {
+ status = "okay";
+ };
+
dma at ea800000 {
status = "okay";
};
@@ -205,10 +209,37 @@
status = "okay";
};
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ button at 1 {
+ label = "wakeup";
+ linux,code = <0x100>;
+ gpios = <&gpio1 1 0x4>;
+ debounce-interval = <20>;
+ gpio-key,wakeup = <1>;
+ };
+ };
+
ehci at e5800000 {
status = "okay";
};
+ i2s0: i2s-play at b2400000 {
+ status = "okay";
+ };
+
+ i2s1: i2s-rec at b2000000 {
+ status = "okay";
+ };
+
+ incodec: dir-hifi {
+ compatible = "dummy,dir-hifi";
+ status = "okay";
+ };
+
ohci at e4000000 {
status = "okay";
};
@@ -217,11 +248,43 @@
status = "okay";
};
+ outcodec: dit-hifi {
+ compatible = "dummy,dit-hifi";
+ status = "okay";
+ };
+
+ sound {
+ compatible = "spear,spear-evb";
+ audio-controllers = <&spdif0 &spdif1 &i2s0 &i2s1>;
+ audio-codecs = <&incodec &outcodec &sta529 &sta529>;
+ codec_dai_name = "dir-hifi", "dit-hifi", "sta529-audio", "sta529-audio";
+ stream_name = "spdif-cap", "spdif-play", "i2s-play", "i2s-cap";
+ dai_name = "spdifin-pcm", "spdifout-pcm", "i2s0-pcm", "i2s1-pcm";
+ nr_controllers = <4>;
+ status = "okay";
+ };
+
+ spdif0: spdif-in at d0100000 {
+ status = "okay";
+ };
+
+ spdif1: spdif-out at d0000000 {
+ status = "okay";
+ };
+
apb {
adc at e0080000 {
status = "okay";
};
+ i2s-play at b2400000 {
+ status = "okay";
+ };
+
+ i2s-rec at b2000000 {
+ status = "okay";
+ };
+
gpio0: gpio at e0600000 {
status = "okay";
};
@@ -232,10 +295,39 @@
i2c0: i2c at e0280000 {
status = "okay";
+
+ sta529: sta529 at 1a {
+ compatible = "st,sta529";
+ reg = <0x1a>;
+ };
};
i2c1: i2c at b4000000 {
status = "okay";
+
+ eeprom0 at 56 {
+ compatible = "st,eeprom";
+ reg = <0x56>;
+ };
+
+ stmpe801 at 41 {
+ compatible = "st,stmpe801";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x41>;
+ irq-over-gpio;
+ irq-gpios = <&gpio0 4 0x4>;
+ id = <0>;
+ blocks = <1>;
+ irq-trigger = <0x2>;
+
+ stmpegpio: stmpe-gpio {
+ compatible = "stmpe,gpio";
+ reg = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+ };
};
kbd at e0300000 {
@@ -344,6 +436,86 @@
spi0: spi at e0100000 {
status = "okay";
+ num-cs = <3>;
+ cs-gpios = <&gpiopinctrl 80 0>, <&gpiopinctrl 24 0>,
+ <&gpiopinctrl 85 0>;
+
+ m25p80 at 0 {
+ status = "okay";
+ compatible = "m25p80";
+ reg = <0>;
+ spi-max-frequency = <12000000>;
+ spi-cpol;
+ spi-cpha;
+ pl022,hierarchy = <0>;
+ pl022,interface = <0>;
+ pl022,slave-tx-disable;
+ pl022,com-mode = <0x2>;
+ pl022,rx-level-trig = <0>;
+ pl022,tx-level-trig = <0>;
+ pl022,ctrl-len = <0x11>;
+ pl022,wait-state = <0>;
+ pl022,duplex = <0>;
+ };
+
+ stmpe610 at 1 {
+ status = "okay";
+ compatible = "st,stmpe610";
+ spi-max-frequency = <1000000>;
+ spi-cpha;
+ reg = <1>;
+ pl022,hierarchy = <0>;
+ pl022,interface = <0>;
+ pl022,slave-tx-disable;
+ pl022,com-mode = <0>;
+ pl022,rx-level-trig = <0>;
+ pl022,tx-level-trig = <0>;
+ pl022,ctrl-len = <0x7>;
+ pl022,wait-state = <0>;
+ pl022,duplex = <0>;
+ irq-over-gpio;
+ irq-gpios = <&gpiopinctrl 100 0>;
+ id = <0>;
+ blocks = <4>;
+ irq-trigger = <0x2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ stmpe610-ts {
+ compatible = "stmpe,ts";
+ reg = <0>;
+ ts,sample-time = <4>;
+ ts,mod-12b = <1>;
+ ts,ref-sel = <0>;
+ ts,adc-freq = <1>;
+ ts,ave-ctrl = <1>;
+ ts,touch-det-delay = <2>;
+ ts,settling = <2>;
+ ts,fraction-z = <7>;
+ ts,i-drive = <1>;
+ };
+ };
+
+ spidev at 2 {
+ status = "okay";
+ compatible = "spidev";
+ reg = <2>;
+ spi-max-frequency = <25000000>;
+ spi-cpha;
+ pl022,hierarchy = <0>;
+ pl022,interface = <0>;
+ pl022,slave-tx-disable;
+ pl022,com-mode = <0x2>;
+ pl022,rx-level-trig = <0>;
+ pl022,tx-level-trig = <0>;
+ pl022,ctrl-len = <0x11>;
+ pl022,wait-state = <0>;
+ pl022,duplex = <0>;
+ };
+ };
+
+ timer at ec800600 {
+ status = "okay";
};
wdt at ec800620 {
diff --git a/arch/arm/boot/dts/spear1340.dtsi b/arch/arm/boot/dts/spear1340.dtsi
index 1446f1b..0d3eb4f 100644
--- a/arch/arm/boot/dts/spear1340.dtsi
+++ b/arch/arm/boot/dts/spear1340.dtsi
@@ -38,9 +38,55 @@
status = "disabled";
};
+ i2s-play at b2400000 {
+ compatible = "snps,designware-i2s";
+ reg = <0xb2400000 0x10000>;
+ interrupt-names = "play_irq";
+ interrupts = <0 98 0x4
+ 0 99 0x4>;
+ play;
+ channel = <8>;
+ status = "disabled";
+ };
+
+ i2s-rec at b2000000 {
+ compatible = "snps,designware-i2s";
+ reg = <0xb2000000 0x10000>;
+ interrupt-names = "record_irq";
+ interrupts = <0 100 0x4
+ 0 101 0x4>;
+ record;
+ channel = <8>;
+ status = "disabled";
+ };
+
+ pwm: pwm at e0180000 {
+ compatible ="st,spear13xx-pwm";
+ reg = <0xe0180000 0x1000>;
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ spdif-in at d0100000 {
+ compatible = "st,spdif-in";
+ reg = < 0xd0100000 0x20000
+ 0xd0110000 0x10000 >;
+ interrupts = <0 84 0x4>;
+ status = "disabled";
+ };
+
+ spdif-out at d0000000 {
+ compatible = "st,spdif-out";
+ reg = <0xd0000000 0x20000>;
+ interrupts = <0 85 0x4>;
+ status = "disabled";
+ };
+
spi1: spi at 5d400000 {
compatible = "arm,pl022", "arm,primecell";
reg = <0x5d400000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
interrupts = <0 99 0x4>;
status = "disabled";
};
diff --git a/arch/arm/boot/dts/spear13xx.dtsi b/arch/arm/boot/dts/spear13xx.dtsi
index 4d35144..2e650f9 100644
--- a/arch/arm/boot/dts/spear13xx.dtsi
+++ b/arch/arm/boot/dts/spear13xx.dtsi
@@ -64,6 +64,18 @@
bootargs = "console=ttyAMA0,115200";
};
+ cpufreq {
+ compatible = "st,cpufreq";
+ cpufreq_tbl = < 166000
+ 200000
+ 250000
+ 300000
+ 400000
+ 500000
+ 600000 >;
+ status = "disable";
+ };
+
ahb {
#address-cells = <1>;
#size-cells = <1>;
@@ -128,6 +140,13 @@
status = "disabled";
};
+ pcm {
+ compatible = "st,pcm-audio";
+ #address-cells = <0>;
+ #size-cells = <0>;
+ status = "disable";
+ };
+
smi: flash at ea000000 {
compatible = "st,spear600-smi";
#address-cells = <1>;
@@ -217,9 +236,29 @@
status = "disabled";
};
+ i2s at e0180000 {
+ compatible = "st,designware-i2s";
+ reg = <0xe0180000 0x1000>;
+ interrupt-names = "play_irq", "record_irq";
+ interrupts = <0 10 0x4
+ 0 11 0x4 >;
+ status = "disabled";
+ };
+
+ i2s at e0200000 {
+ compatible = "st,designware-i2s";
+ reg = <0xe0200000 0x1000>;
+ interrupt-names = "play_irq", "record_irq";
+ interrupts = <0 26 0x4
+ 0 53 0x4>;
+ status = "disabled";
+ };
+
spi0: spi at e0100000 {
compatible = "arm,pl022", "arm,primecell";
reg = <0xe0100000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
interrupts = <0 31 0x4>;
status = "disabled";
};
diff --git a/arch/arm/boot/dts/spear320.dtsi b/arch/arm/boot/dts/spear320.dtsi
index 02113f3..582ded7 100644
--- a/arch/arm/boot/dts/spear320.dtsi
+++ b/arch/arm/boot/dts/spear320.dtsi
@@ -55,15 +55,26 @@
spi1: spi at a5000000 {
compatible = "arm,pl022", "arm,primecell";
reg = <0xa5000000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
status = "disabled";
};
spi2: spi at a6000000 {
compatible = "arm,pl022", "arm,primecell";
reg = <0xa6000000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
status = "disabled";
};
+ pwm: pwm at a8000000 {
+ compatible ="st,spear-pwm";
+ reg = <0xa8000000 0x1000>;
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
apb {
#address-cells = <1>;
#size-cells = <1>;
diff --git a/arch/arm/boot/dts/spear3xx.dtsi b/arch/arm/boot/dts/spear3xx.dtsi
index 4946360..c2a852d 100644
--- a/arch/arm/boot/dts/spear3xx.dtsi
+++ b/arch/arm/boot/dts/spear3xx.dtsi
@@ -70,6 +70,8 @@
compatible = "arm,pl022", "arm,primecell";
reg = <0xd0100000 0x1000>;
interrupts = <20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
status = "disabled";
};
diff --git a/arch/arm/boot/dts/spear600-evb.dts b/arch/arm/boot/dts/spear600-evb.dts
index 5e6ef03..d865a89 100644
--- a/arch/arm/boot/dts/spear600-evb.dts
+++ b/arch/arm/boot/dts/spear600-evb.dts
@@ -24,15 +24,35 @@
};
ahb {
+ clcd at fc200000 {
+ status = "okay";
+ };
+
dma at fc400000 {
status = "okay";
};
+ ehci at e1800000 {
+ status = "okay";
+ };
+
+ ehci at e2000000 {
+ status = "okay";
+ };
+
gmac: ethernet at e0800000 {
phy-mode = "gmii";
status = "okay";
};
+ ohci at e1900000 {
+ status = "okay";
+ };
+
+ ohci at e2100000 {
+ status = "okay";
+ };
+
smi: flash at fc000000 {
status = "okay";
clock-rate=<50000000>;
@@ -83,6 +103,10 @@
pinctrl-0 = <>;
};
+ rtc at fc900000 {
+ status = "okay";
+ };
+
i2c at d0200000 {
clock-frequency = <400000>;
status = "okay";
diff --git a/arch/arm/boot/dts/spear600.dtsi b/arch/arm/boot/dts/spear600.dtsi
index f74feea..e051dde 100644
--- a/arch/arm/boot/dts/spear600.dtsi
+++ b/arch/arm/boot/dts/spear600.dtsi
@@ -45,6 +45,14 @@
#interrupt-cells = <1>;
};
+ clcd at fc200000 {
+ compatible = "arm,pl110", "arm,primecell";
+ reg = <0xfc200000 0x1000>;
+ interrupt-parent = <&vic1>;
+ interrupts = <12>;
+ status = "disabled";
+ };
+
dma at fc400000 {
compatible = "arm,pl080", "arm,primecell";
reg = <0xfc400000 0x1000>;
@@ -179,6 +187,13 @@
status = "disabled";
};
+ rtc at fc900000 {
+ compatible = "st,spear600-rtc";
+ reg = <0xfc900000 0x1000>;
+ interrupts = <10>;
+ status = "disabled";
+ };
+
timer at f0000000 {
compatible = "st,spear-timer";
reg = <0xf0000000 0x400>;
--
1.7.12.rc2.18.g61b472e
next prev parent reply other threads:[~2012-11-11 4:39 UTC|newest]
Thread overview: 40+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-11-11 4:39 [PATCH 00/14] ARM: SPEAr: DT updates Viresh Kumar
2012-11-11 4:39 ` [PATCH 01/14] pinctrl: SPEAr: add spi chipselect control driver Viresh Kumar
2012-11-12 15:03 ` Arnd Bergmann
2012-11-15 14:17 ` Linus Walleij
2012-11-15 14:19 ` Viresh Kumar
2012-11-15 19:09 ` Linus Walleij
2012-11-16 5:15 ` [PATCH 01/16] gpio: " Viresh Kumar
2012-11-16 8:19 ` Arnd Bergmann
2012-11-16 8:19 ` Viresh Kumar
2012-11-17 23:02 ` Linus Walleij
2012-11-11 4:39 ` [PATCH 02/14] ARM: SPEAr13xx: DT: Add spics gpio controller nodes Viresh Kumar
2012-11-13 14:08 ` Linus Walleij
2012-11-13 14:34 ` Viresh Kumar
2012-11-15 14:06 ` Linus Walleij
2012-11-15 14:08 ` Viresh Kumar
2012-11-15 17:25 ` Linus Walleij
2012-11-11 4:39 ` [PATCH 03/14] ARM: SPEAr: DT: Update pinctrl list Viresh Kumar
2012-11-11 4:39 ` [PATCH 04/14] ARM: SPEAr: DT: Update partition info for MTD devices Viresh Kumar
2012-11-11 4:39 ` [PATCH 05/14] ARM: SPEAr: DT: Fix existing DT support Viresh Kumar
2012-11-11 4:39 ` [PATCH 06/14] ARM: SPEAr: DT: Modify DT bindings for STMMAC Viresh Kumar
2012-11-11 4:39 ` [PATCH 07/14] ARM: SPEAr: DT: add uart state to fix warning Viresh Kumar
2012-11-11 4:39 ` Viresh Kumar [this message]
2012-11-26 11:25 ` [PATCH 08/14] ARM: SPEAr: DT: Update device nodes Viresh Kumar
2012-11-11 4:39 ` [PATCH 09/14] ARM: SPEAr1310: Move 1310 specific misc register into machine specific files Viresh Kumar
2012-11-11 4:39 ` [PATCH 10/14] ARM: SPEAr13xx: Remove fields not required for ssp controller Viresh Kumar
2012-11-11 4:39 ` [PATCH 11/14] ARM: SPEAr1310: Fix AUXDATA for compact flash controller Viresh Kumar
2012-11-11 4:39 ` [PATCH 12/14] ARM: SPEAr3xx: shirq: simplify and move the shared irq multiplexor to DT Viresh Kumar
2012-11-12 15:09 ` Arnd Bergmann
2012-11-12 16:37 ` viresh kumar
2012-11-12 17:00 ` Arnd Bergmann
2012-11-12 17:16 ` [PATCH] fixup! " Viresh Kumar
2012-11-12 17:35 ` [PATCH] ARM: SPEAr3xx: Shirq: Move shirq controller out of plat/ Viresh Kumar
2012-11-11 4:39 ` [PATCH 13/14] ARM: SPEAr3xx: DT: add shirq node for interrupt multiplexor Viresh Kumar
2012-11-11 4:39 ` [PATCH 14/14] ARM: SPEAr320: DT: Add SPEAr 320 HMI board support Viresh Kumar
2012-11-12 15:21 ` [PATCH 00/14] ARM: SPEAr: DT updates Arnd Bergmann
2012-11-12 16:39 ` viresh kumar
2012-11-12 17:18 ` Viresh Kumar
2012-11-21 20:24 ` Olof Johansson
2012-11-22 3:19 ` Viresh Kumar
2012-11-22 9:47 ` Linus Walleij
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=b3925b105ee2c6fe828ef3b54928aeee02a801ae.1352608333.git.viresh.kumar@linaro.org \
--to=viresh.kumar@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).