* [PATCH V2 1/9] clk: Add non CONFIG_HAVE_CLK routines
2012-04-24 5:56 [PATCH V2 0/9] clk: Add non CONFIG_HAVE_CLK routines Viresh Kumar
@ 2012-04-24 5:56 ` Viresh Kumar
2012-04-24 5:56 ` [PATCH V2 2/9] clk: Remove redundant depends on from drivers/Kconfig Viresh Kumar
` (7 subsequent siblings)
8 siblings, 0 replies; 14+ messages in thread
From: Viresh Kumar @ 2012-04-24 5:56 UTC (permalink / raw)
To: linux-arm-kernel
Many drivers are shared between architectures that may or may not have HAVE_CLK
selected for them. To remove compilation errors for them we enclose clk_*()
calls in these drivers within #ifdef CONFIG_HAVE_CLK, #endif.
This patch removes the need of these CONFIG_HAVE_CLK statements, by introducing
dummy routines when HAVE_CLK is not selected by platforms. So, definition of
these routines will always be available. These calls will return error for
platforms that don't select HAVE_CLK.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
---
include/linux/clk.h | 168 +++++++++++++++++++++++++++++++++------------------
1 files changed, 109 insertions(+), 59 deletions(-)
diff --git a/include/linux/clk.h b/include/linux/clk.h
index 70cf722..3266b0c 100644
--- a/include/linux/clk.h
+++ b/include/linux/clk.h
@@ -84,6 +84,43 @@ int clk_notifier_unregister(struct clk *clk, struct notifier_block *nb);
#endif /* !CONFIG_COMMON_CLK */
/**
+ * clk_prepare - prepare a clock source
+ * @clk: clock source
+ *
+ * This prepares the clock source for use.
+ *
+ * Must not be called from within atomic context.
+ */
+#ifdef CONFIG_HAVE_CLK_PREPARE
+int clk_prepare(struct clk *clk);
+#else
+static inline int clk_prepare(struct clk *clk)
+{
+ might_sleep();
+ return 0;
+}
+#endif
+
+/**
+ * clk_unprepare - undo preparation of a clock source
+ * @clk: clock source
+ *
+ * This undoes a previously prepared clock. The caller must balance
+ * the number of prepare and unprepare calls.
+ *
+ * Must not be called from within atomic context.
+ */
+#ifdef CONFIG_HAVE_CLK_PREPARE
+void clk_unprepare(struct clk *clk);
+#else
+static inline void clk_unprepare(struct clk *clk)
+{
+ might_sleep();
+}
+#endif
+
+#ifdef CONFIG_HAVE_CLK
+/**
* clk_get - lookup and obtain a reference to a clock producer.
* @dev: device for clock "consumer"
* @id: clock comsumer ID
@@ -121,24 +158,6 @@ struct clk *clk_get(struct device *dev, const char *id);
struct clk *devm_clk_get(struct device *dev, const char *id);
/**
- * clk_prepare - prepare a clock source
- * @clk: clock source
- *
- * This prepares the clock source for use.
- *
- * Must not be called from within atomic context.
- */
-#ifdef CONFIG_HAVE_CLK_PREPARE
-int clk_prepare(struct clk *clk);
-#else
-static inline int clk_prepare(struct clk *clk)
-{
- might_sleep();
- return 0;
-}
-#endif
-
-/**
* clk_enable - inform the system when the clock source should be running.
* @clk: clock source
*
@@ -166,47 +185,6 @@ int clk_enable(struct clk *clk);
*/
void clk_disable(struct clk *clk);
-
-/**
- * clk_unprepare - undo preparation of a clock source
- * @clk: clock source
- *
- * This undoes a previously prepared clock. The caller must balance
- * the number of prepare and unprepare calls.
- *
- * Must not be called from within atomic context.
- */
-#ifdef CONFIG_HAVE_CLK_PREPARE
-void clk_unprepare(struct clk *clk);
-#else
-static inline void clk_unprepare(struct clk *clk)
-{
- might_sleep();
-}
-#endif
-
-/* clk_prepare_enable helps cases using clk_enable in non-atomic context. */
-static inline int clk_prepare_enable(struct clk *clk)
-{
- int ret;
-
- ret = clk_prepare(clk);
- if (ret)
- return ret;
- ret = clk_enable(clk);
- if (ret)
- clk_unprepare(clk);
-
- return ret;
-}
-
-/* clk_disable_unprepare helps cases using clk_disable in non-atomic context. */
-static inline void clk_disable_unprepare(struct clk *clk)
-{
- clk_disable(clk);
- clk_unprepare(clk);
-}
-
/**
* clk_get_rate - obtain the current clock rate (in Hz) for a clock source.
* This is only valid once the clock source has been enabled.
@@ -297,6 +275,78 @@ struct clk *clk_get_parent(struct clk *clk);
*/
struct clk *clk_get_sys(const char *dev_id, const char *con_id);
+#else /* !CONFIG_HAVE_CLK */
+
+static inline struct clk *clk_get(struct device *dev, const char *id)
+{
+ return ERR_PTR(-ENODEV);
+}
+
+static inline struct clk *devm_clk_get(struct device *dev, const char *id)
+{
+ return ERR_PTR(-ENODEV);
+}
+
+static inline void clk_put(struct clk *clk) {}
+
+static inline void devm_clk_put(struct device *dev, struct clk *clk) {}
+
+static inline int clk_enable(struct clk *clk)
+{
+ return -ENODEV;
+}
+
+static inline void clk_disable(struct clk *clk) {}
+
+static inline unsigned long clk_get_rate(struct clk *clk)
+{
+ return -ENODEV;
+}
+
+static inline int clk_set_rate(struct clk *clk, unsigned long rate)
+{
+ return -ENODEV;
+}
+
+static inline long clk_round_rate(struct clk *clk, unsigned long rate)
+{
+ return -ENODEV;
+}
+
+static inline int clk_set_parent(struct clk *clk, struct clk *parent)
+{
+ return -ENODEV;
+}
+
+static inline struct clk *clk_get_parent(struct clk *clk)
+{
+ return ERR_PTR(-ENODEV);
+}
+
+#endif
+
+/* clk_prepare_enable helps cases using clk_enable in non-atomic context. */
+static inline int clk_prepare_enable(struct clk *clk)
+{
+ int ret;
+
+ ret = clk_prepare(clk);
+ if (ret)
+ return ret;
+ ret = clk_enable(clk);
+ if (ret)
+ clk_unprepare(clk);
+
+ return ret;
+}
+
+/* clk_disable_unprepare helps cases using clk_disable in non-atomic context. */
+static inline void clk_disable_unprepare(struct clk *clk)
+{
+ clk_disable(clk);
+ clk_unprepare(clk);
+}
+
/**
* clk_add_alias - add a new clock alias
* @alias: name for clock alias
--
1.7.9
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH V2 2/9] clk: Remove redundant depends on from drivers/Kconfig
2012-04-24 5:56 [PATCH V2 0/9] clk: Add non CONFIG_HAVE_CLK routines Viresh Kumar
2012-04-24 5:56 ` [PATCH V2 1/9] " Viresh Kumar
@ 2012-04-24 5:56 ` Viresh Kumar
2012-04-24 5:56 ` [PATCH V2 3/9] ata/pata_arasan: Remove conditional compilation of clk code Viresh Kumar
` (6 subsequent siblings)
8 siblings, 0 replies; 14+ messages in thread
From: Viresh Kumar @ 2012-04-24 5:56 UTC (permalink / raw)
To: linux-arm-kernel
menu "Common Clock Framework" has "depends on COMMON_CLK" and so configs defined
within menu don't require these "depends on COMMON_CLK again".
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
---
drivers/clk/Kconfig | 2 --
1 files changed, 0 insertions(+), 2 deletions(-)
diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index 165e1fe..4f10a21 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -24,7 +24,6 @@ menu "Common Clock Framework"
config COMMON_CLK_DISABLE_UNUSED
bool "Disabled unused clocks at boot"
- depends on COMMON_CLK
---help---
Traverses the entire clock tree and disables any clocks that are
enabled in hardware but have not been enabled by any device drivers.
@@ -35,7 +34,6 @@ config COMMON_CLK_DISABLE_UNUSED
config COMMON_CLK_DEBUG
bool "DebugFS representation of clock tree"
- depends on COMMON_CLK
select DEBUG_FS
---help---
Creates a directory hierchy in debugfs for visualizing the clk
--
1.7.9
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH V2 3/9] ata/pata_arasan: Remove conditional compilation of clk code
2012-04-24 5:56 [PATCH V2 0/9] clk: Add non CONFIG_HAVE_CLK routines Viresh Kumar
2012-04-24 5:56 ` [PATCH V2 1/9] " Viresh Kumar
2012-04-24 5:56 ` [PATCH V2 2/9] clk: Remove redundant depends on from drivers/Kconfig Viresh Kumar
@ 2012-04-24 5:56 ` Viresh Kumar
2012-04-24 5:56 ` [PATCH V2 4/9] ata/sata_mv: " Viresh Kumar
` (5 subsequent siblings)
8 siblings, 0 replies; 14+ messages in thread
From: Viresh Kumar @ 2012-04-24 5:56 UTC (permalink / raw)
To: linux-arm-kernel
With addition of dummy clk_*() calls for non CONFIG_HAVE_CLK cases in clk.h,
there is no need to have clk code enclosed in #ifdef CONFIG_HAVE_CLK, #endif
macros.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Jeff Garzik <jgarzik@redhat.com>
Cc: linux-ide at vger.kernel.org
---
drivers/ata/pata_arasan_cf.c | 39 ++++++++++++++++-----------------------
1 files changed, 16 insertions(+), 23 deletions(-)
diff --git a/drivers/ata/pata_arasan_cf.c b/drivers/ata/pata_arasan_cf.c
index fc2db2a..b370e35 100644
--- a/drivers/ata/pata_arasan_cf.c
+++ b/drivers/ata/pata_arasan_cf.c
@@ -184,10 +184,8 @@
struct arasan_cf_dev {
/* pointer to ata_host structure */
struct ata_host *host;
- /* clk structure, only if HAVE_CLK is defined */
-#ifdef CONFIG_HAVE_CLK
+ /* clk structure */
struct clk *clk;
-#endif
/* physical base address of controller */
dma_addr_t pbase;
@@ -312,13 +310,13 @@ static int cf_init(struct arasan_cf_dev *acdev)
unsigned long flags;
int ret = 0;
-#ifdef CONFIG_HAVE_CLK
- ret = clk_enable(acdev->clk);
- if (ret) {
- dev_dbg(acdev->host->dev, "clock enable failed");
- return ret;
+ if (!IS_ERR(acdev->clk)) {
+ ret = clk_enable(acdev->clk);
+ if (ret) {
+ dev_dbg(acdev->host->dev, "clock enable failed");
+ return ret;
+ }
}
-#endif
spin_lock_irqsave(&acdev->host->lock, flags);
/* configure CF interface clock */
@@ -344,9 +342,9 @@ static void cf_exit(struct arasan_cf_dev *acdev)
writel(readl(acdev->vbase + OP_MODE) & ~CFHOST_ENB,
acdev->vbase + OP_MODE);
spin_unlock_irqrestore(&acdev->host->lock, flags);
-#ifdef CONFIG_HAVE_CLK
- clk_disable(acdev->clk);
-#endif
+
+ if (!IS_ERR(acdev->clk))
+ clk_disable(acdev->clk);
}
static void dma_callback(void *dev)
@@ -828,13 +826,9 @@ static int __devinit arasan_cf_probe(struct platform_device *pdev)
return -ENOMEM;
}
-#ifdef CONFIG_HAVE_CLK
acdev->clk = clk_get(&pdev->dev, NULL);
- if (IS_ERR(acdev->clk)) {
+ if (IS_ERR(acdev->clk))
dev_warn(&pdev->dev, "Clock not found\n");
- return PTR_ERR(acdev->clk);
- }
-#endif
/* allocate host */
host = ata_host_alloc(&pdev->dev, 1);
@@ -899,9 +893,8 @@ static int __devinit arasan_cf_probe(struct platform_device *pdev)
&arasan_cf_sht);
free_clk:
-#ifdef CONFIG_HAVE_CLK
- clk_put(acdev->clk);
-#endif
+ if (!IS_ERR(acdev->clk))
+ clk_put(acdev->clk);
return ret;
}
@@ -912,9 +905,9 @@ static int __devexit arasan_cf_remove(struct platform_device *pdev)
ata_host_detach(host);
cf_exit(acdev);
-#ifdef CONFIG_HAVE_CLK
- clk_put(acdev->clk);
-#endif
+
+ if (!IS_ERR(acdev->clk))
+ clk_put(acdev->clk);
return 0;
}
--
1.7.9
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH V2 4/9] ata/sata_mv: Remove conditional compilation of clk code
2012-04-24 5:56 [PATCH V2 0/9] clk: Add non CONFIG_HAVE_CLK routines Viresh Kumar
` (2 preceding siblings ...)
2012-04-24 5:56 ` [PATCH V2 3/9] ata/pata_arasan: Remove conditional compilation of clk code Viresh Kumar
@ 2012-04-24 5:56 ` Viresh Kumar
2012-04-24 5:56 ` [PATCH V2 5/9] net/c_can: " Viresh Kumar
` (4 subsequent siblings)
8 siblings, 0 replies; 14+ messages in thread
From: Viresh Kumar @ 2012-04-24 5:56 UTC (permalink / raw)
To: linux-arm-kernel
With addition of dummy clk_*() calls for non CONFIG_HAVE_CLK cases in clk.h,
there is no need to have clk code enclosed in #ifdef CONFIG_HAVE_CLK, #endif
macros.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Jeff Garzik <jgarzik@redhat.com>
Cc: linux-ide at vger.kernel.org
---
drivers/ata/sata_mv.c | 10 ----------
1 files changed, 0 insertions(+), 10 deletions(-)
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
index 7336d4a..37503b8 100644
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -551,9 +551,7 @@ struct mv_host_priv {
u32 irq_mask_offset;
u32 unmask_all_irqs;
-#if defined(CONFIG_HAVE_CLK)
struct clk *clk;
-#endif
/*
* These consistent DMA memory pools give us guaranteed
* alignment for hardware-accessed data structures,
@@ -4063,13 +4061,11 @@ static int mv_platform_probe(struct platform_device *pdev)
resource_size(res));
hpriv->base -= SATAHC0_REG_BASE;
-#if defined(CONFIG_HAVE_CLK)
hpriv->clk = clk_get(&pdev->dev, NULL);
if (IS_ERR(hpriv->clk))
dev_notice(&pdev->dev, "cannot get clkdev\n");
else
clk_enable(hpriv->clk);
-#endif
/*
* (Re-)program MBUS remapping windows if we are asked to.
@@ -4096,12 +4092,10 @@ static int mv_platform_probe(struct platform_device *pdev)
return 0;
err:
-#if defined(CONFIG_HAVE_CLK)
if (!IS_ERR(hpriv->clk)) {
clk_disable(hpriv->clk);
clk_put(hpriv->clk);
}
-#endif
return rc;
}
@@ -4117,17 +4111,13 @@ err:
static int __devexit mv_platform_remove(struct platform_device *pdev)
{
struct ata_host *host = platform_get_drvdata(pdev);
-#if defined(CONFIG_HAVE_CLK)
struct mv_host_priv *hpriv = host->private_data;
-#endif
ata_host_detach(host);
-#if defined(CONFIG_HAVE_CLK)
if (!IS_ERR(hpriv->clk)) {
clk_disable(hpriv->clk);
clk_put(hpriv->clk);
}
-#endif
return 0;
}
--
1.7.9
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH V2 5/9] net/c_can: Remove conditional compilation of clk code
2012-04-24 5:56 [PATCH V2 0/9] clk: Add non CONFIG_HAVE_CLK routines Viresh Kumar
` (3 preceding siblings ...)
2012-04-24 5:56 ` [PATCH V2 4/9] ata/sata_mv: " Viresh Kumar
@ 2012-04-24 5:56 ` Viresh Kumar
2012-04-24 5:56 ` [PATCH V2 6/9] net/stmmac: " Viresh Kumar
` (3 subsequent siblings)
8 siblings, 0 replies; 14+ messages in thread
From: Viresh Kumar @ 2012-04-24 5:56 UTC (permalink / raw)
To: linux-arm-kernel
With addition of dummy clk_*() calls for non CONFIG_HAVE_CLK cases in clk.h,
there is no need to have clk code enclosed in #ifdef CONFIG_HAVE_CLK, #endif
macros.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Bhupesh Sharma <bhupesh.sharma@st.com>
---
drivers/net/can/c_can/c_can_platform.c | 28 +++++++++++-----------------
1 files changed, 11 insertions(+), 17 deletions(-)
diff --git a/drivers/net/can/c_can/c_can_platform.c b/drivers/net/can/c_can/c_can_platform.c
index 5e1a5ff..d28904d 100644
--- a/drivers/net/can/c_can/c_can_platform.c
+++ b/drivers/net/can/c_can/c_can_platform.c
@@ -73,17 +73,12 @@ static int __devinit c_can_plat_probe(struct platform_device *pdev)
struct c_can_priv *priv;
struct resource *mem;
int irq;
-#ifdef CONFIG_HAVE_CLK
struct clk *clk;
/* get the appropriate clk */
clk = clk_get(&pdev->dev, NULL);
- if (IS_ERR(clk)) {
+ if (IS_ERR(clk))
dev_err(&pdev->dev, "no clock defined\n");
- ret = -ENODEV;
- goto exit;
- }
-#endif
/* get the platform data */
mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
@@ -118,10 +113,11 @@ static int __devinit c_can_plat_probe(struct platform_device *pdev)
dev->irq = irq;
priv->regs = addr;
-#ifdef CONFIG_HAVE_CLK
- priv->can.clock.freq = clk_get_rate(clk);
- priv->priv = clk;
-#endif
+
+ if (!IS_ERR(clk)) {
+ priv->can.clock.freq = clk_get_rate(clk);
+ priv->priv = clk;
+ }
switch (mem->flags & IORESOURCE_MEM_TYPE_MASK) {
case IORESOURCE_MEM_32BIT:
@@ -157,10 +153,9 @@ exit_iounmap:
exit_release_mem:
release_mem_region(mem->start, resource_size(mem));
exit_free_clk:
-#ifdef CONFIG_HAVE_CLK
- clk_put(clk);
-exit:
-#endif
+ if (!IS_ERR(clk))
+ clk_put(clk);
+
dev_err(&pdev->dev, "probe failed\n");
return ret;
@@ -181,9 +176,8 @@ static int __devexit c_can_plat_remove(struct platform_device *pdev)
mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
release_mem_region(mem->start, resource_size(mem));
-#ifdef CONFIG_HAVE_CLK
- clk_put(priv->priv);
-#endif
+ if (!IS_ERR(priv->priv))
+ clk_put(priv->priv);
return 0;
}
--
1.7.9
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH V2 6/9] net/stmmac: Remove conditional compilation of clk code
2012-04-24 5:56 [PATCH V2 0/9] clk: Add non CONFIG_HAVE_CLK routines Viresh Kumar
` (4 preceding siblings ...)
2012-04-24 5:56 ` [PATCH V2 5/9] net/c_can: " Viresh Kumar
@ 2012-04-24 5:56 ` Viresh Kumar
2012-04-24 6:16 ` Giuseppe CAVALLARO
2012-04-24 5:56 ` [PATCH V2 7/9] gadget/m66592: " Viresh Kumar
` (2 subsequent siblings)
8 siblings, 1 reply; 14+ messages in thread
From: Viresh Kumar @ 2012-04-24 5:56 UTC (permalink / raw)
To: linux-arm-kernel
With addition of dummy clk_*() calls for non CONFIG_HAVE_CLK cases in clk.h,
there is no need to have clk code enclosed in #ifdef CONFIG_HAVE_CLK, #endif
macros.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: David S. Miller <davem@davemloft.net>
---
drivers/net/ethernet/stmicro/stmmac/stmmac.h | 41 ---------------------
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 31 ++++++++++------
2 files changed, 19 insertions(+), 53 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
index db2de9a..7f85895 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
@@ -81,9 +81,7 @@ struct stmmac_priv {
struct stmmac_counters mmc;
struct dma_features dma_cap;
int hw_cap_support;
-#ifdef CONFIG_HAVE_CLK
struct clk *stmmac_clk;
-#endif
int clk_csr;
};
@@ -103,42 +101,3 @@ int stmmac_dvr_remove(struct net_device *ndev);
struct stmmac_priv *stmmac_dvr_probe(struct device *device,
struct plat_stmmacenet_data *plat_dat,
void __iomem *addr);
-
-#ifdef CONFIG_HAVE_CLK
-static inline int stmmac_clk_enable(struct stmmac_priv *priv)
-{
- if (!IS_ERR(priv->stmmac_clk))
- return clk_enable(priv->stmmac_clk);
-
- return 0;
-}
-
-static inline void stmmac_clk_disable(struct stmmac_priv *priv)
-{
- if (IS_ERR(priv->stmmac_clk))
- return;
-
- clk_disable(priv->stmmac_clk);
-}
-static inline int stmmac_clk_get(struct stmmac_priv *priv)
-{
- priv->stmmac_clk = clk_get(priv->device, NULL);
-
- if (IS_ERR(priv->stmmac_clk))
- return PTR_ERR(priv->stmmac_clk);
-
- return 0;
-}
-#else
-static inline int stmmac_clk_enable(struct stmmac_priv *priv)
-{
- return 0;
-}
-static inline void stmmac_clk_disable(struct stmmac_priv *priv)
-{
-}
-static inline int stmmac_clk_get(struct stmmac_priv *priv)
-{
- return 0;
-}
-#endif /* CONFIG_HAVE_CLK */
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 1a4cf81..18ce287 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -28,6 +28,7 @@
https://bugzilla.stlinux.com/
*******************************************************************************/
+#include <linux/clk.h>
#include <linux/kernel.h>
#include <linux/interrupt.h>
#include <linux/ip.h>
@@ -165,7 +166,6 @@ static void stmmac_verify_args(void)
static void stmmac_clk_csr_set(struct stmmac_priv *priv)
{
-#ifdef CONFIG_HAVE_CLK
u32 clk_rate;
if (IS_ERR(priv->stmmac_clk))
@@ -192,7 +192,6 @@ static void stmmac_clk_csr_set(struct stmmac_priv *priv)
* we can not estimate the proper divider as it is not known
* the frequency of clk_csr_i. So we do not change the default
* divider. */
-#endif
}
#if defined(STMMAC_XMIT_DEBUG) || defined(STMMAC_RX_DEBUG)
@@ -971,7 +970,8 @@ static int stmmac_open(struct net_device *dev)
} else
priv->tm->enable = 1;
#endif
- stmmac_clk_enable(priv);
+ if (!IS_ERR(priv->stmmac_clk))
+ clk_enable(priv->stmmac_clk);
stmmac_check_ether_addr(priv);
@@ -1075,7 +1075,8 @@ open_error:
if (priv->phydev)
phy_disconnect(priv->phydev);
- stmmac_clk_disable(priv);
+ if (!IS_ERR(priv->stmmac_clk))
+ clk_disable(priv->stmmac_clk);
return ret;
}
@@ -1128,7 +1129,9 @@ static int stmmac_release(struct net_device *dev)
#ifdef CONFIG_STMMAC_DEBUG_FS
stmmac_exit_fs();
#endif
- stmmac_clk_disable(priv);
+
+ if (!IS_ERR(priv->stmmac_clk))
+ clk_disable(priv->stmmac_clk);
return 0;
}
@@ -1925,7 +1928,8 @@ struct stmmac_priv *stmmac_dvr_probe(struct device *device,
goto error;
}
- if (stmmac_clk_get(priv))
+ priv->stmmac_clk = clk_get(priv->device, NULL);
+ if (IS_ERR(priv->stmmac_clk))
pr_warning("%s: warning: cannot get CSR clock\n", __func__);
/* If a specific clk_csr value is passed from the platform
@@ -1934,10 +1938,12 @@ struct stmmac_priv *stmmac_dvr_probe(struct device *device,
* set the MDC clock dynamically according to the csr actual
* clock input.
*/
- if (!priv->plat->clk_csr)
- stmmac_clk_csr_set(priv);
- else
+ if (!priv->plat->clk_csr) {
+ if (!IS_ERR(priv->stmmac_clk))
+ stmmac_clk_csr_set(priv);
+ } else {
priv->clk_csr = priv->plat->clk_csr;
+ }
/* MDIO bus Registration */
ret = stmmac_mdio_register(ndev);
@@ -2020,7 +2026,8 @@ int stmmac_suspend(struct net_device *ndev)
else {
stmmac_set_mac(priv->ioaddr, false);
/* Disable clock in case of PWM is off */
- stmmac_clk_disable(priv);
+ if (!IS_ERR(priv->stmmac_clk))
+ clk_disable(priv->stmmac_clk);
}
spin_unlock(&priv->lock);
return 0;
@@ -2042,9 +2049,9 @@ int stmmac_resume(struct net_device *ndev)
* from another devices (e.g. serial console). */
if (device_may_wakeup(priv->device))
priv->hw->mac->pmt(priv->ioaddr, 0);
- else
+ else if (!IS_ERR(priv->stmmac_clk))
/* enable the clk prevously disabled */
- stmmac_clk_enable(priv);
+ clk_enable(priv->stmmac_clk);
netif_device_attach(ndev);
--
1.7.9
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH V2 6/9] net/stmmac: Remove conditional compilation of clk code
2012-04-24 5:56 ` [PATCH V2 6/9] net/stmmac: " Viresh Kumar
@ 2012-04-24 6:16 ` Giuseppe CAVALLARO
2012-04-24 6:33 ` Giuseppe CAVALLARO
0 siblings, 1 reply; 14+ messages in thread
From: Giuseppe CAVALLARO @ 2012-04-24 6:16 UTC (permalink / raw)
To: linux-arm-kernel
On 4/24/2012 7:56 AM, Viresh KUMAR wrote:
> With addition of dummy clk_*() calls for non CONFIG_HAVE_CLK cases in clk.h,
> there is no need to have clk code enclosed in #ifdef CONFIG_HAVE_CLK, #endif
> macros.
Hello Viresh
patch only applies fine against the net-next repository so on top of the
diver version: March_2012 and it builds fine on arch w/ w/o HAVE_CLK
(just tested).
Thanks a lot.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
> Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
> Cc: David S. Miller <davem@davemloft.net>
> ---
> drivers/net/ethernet/stmicro/stmmac/stmmac.h | 41 ---------------------
> drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 31 ++++++++++------
> 2 files changed, 19 insertions(+), 53 deletions(-)
>
> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
> index db2de9a..7f85895 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h
> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
> @@ -81,9 +81,7 @@ struct stmmac_priv {
> struct stmmac_counters mmc;
> struct dma_features dma_cap;
> int hw_cap_support;
> -#ifdef CONFIG_HAVE_CLK
> struct clk *stmmac_clk;
> -#endif
> int clk_csr;
> };
>
> @@ -103,42 +101,3 @@ int stmmac_dvr_remove(struct net_device *ndev);
> struct stmmac_priv *stmmac_dvr_probe(struct device *device,
> struct plat_stmmacenet_data *plat_dat,
> void __iomem *addr);
> -
> -#ifdef CONFIG_HAVE_CLK
> -static inline int stmmac_clk_enable(struct stmmac_priv *priv)
> -{
> - if (!IS_ERR(priv->stmmac_clk))
> - return clk_enable(priv->stmmac_clk);
> -
> - return 0;
> -}
> -
> -static inline void stmmac_clk_disable(struct stmmac_priv *priv)
> -{
> - if (IS_ERR(priv->stmmac_clk))
> - return;
> -
> - clk_disable(priv->stmmac_clk);
> -}
> -static inline int stmmac_clk_get(struct stmmac_priv *priv)
> -{
> - priv->stmmac_clk = clk_get(priv->device, NULL);
> -
> - if (IS_ERR(priv->stmmac_clk))
> - return PTR_ERR(priv->stmmac_clk);
> -
> - return 0;
> -}
> -#else
> -static inline int stmmac_clk_enable(struct stmmac_priv *priv)
> -{
> - return 0;
> -}
> -static inline void stmmac_clk_disable(struct stmmac_priv *priv)
> -{
> -}
> -static inline int stmmac_clk_get(struct stmmac_priv *priv)
> -{
> - return 0;
> -}
> -#endif /* CONFIG_HAVE_CLK */
> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
> index 1a4cf81..18ce287 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
> @@ -28,6 +28,7 @@
> https://bugzilla.stlinux.com/
> *******************************************************************************/
>
> +#include <linux/clk.h>
> #include <linux/kernel.h>
> #include <linux/interrupt.h>
> #include <linux/ip.h>
> @@ -165,7 +166,6 @@ static void stmmac_verify_args(void)
>
> static void stmmac_clk_csr_set(struct stmmac_priv *priv)
> {
> -#ifdef CONFIG_HAVE_CLK
> u32 clk_rate;
>
> if (IS_ERR(priv->stmmac_clk))
> @@ -192,7 +192,6 @@ static void stmmac_clk_csr_set(struct stmmac_priv *priv)
> * we can not estimate the proper divider as it is not known
> * the frequency of clk_csr_i. So we do not change the default
> * divider. */
> -#endif
> }
>
> #if defined(STMMAC_XMIT_DEBUG) || defined(STMMAC_RX_DEBUG)
> @@ -971,7 +970,8 @@ static int stmmac_open(struct net_device *dev)
> } else
> priv->tm->enable = 1;
> #endif
> - stmmac_clk_enable(priv);
> + if (!IS_ERR(priv->stmmac_clk))
> + clk_enable(priv->stmmac_clk);
>
> stmmac_check_ether_addr(priv);
>
> @@ -1075,7 +1075,8 @@ open_error:
> if (priv->phydev)
> phy_disconnect(priv->phydev);
>
> - stmmac_clk_disable(priv);
> + if (!IS_ERR(priv->stmmac_clk))
> + clk_disable(priv->stmmac_clk);
>
> return ret;
> }
> @@ -1128,7 +1129,9 @@ static int stmmac_release(struct net_device *dev)
> #ifdef CONFIG_STMMAC_DEBUG_FS
> stmmac_exit_fs();
> #endif
> - stmmac_clk_disable(priv);
> +
> + if (!IS_ERR(priv->stmmac_clk))
> + clk_disable(priv->stmmac_clk);
>
> return 0;
> }
> @@ -1925,7 +1928,8 @@ struct stmmac_priv *stmmac_dvr_probe(struct device *device,
> goto error;
> }
>
> - if (stmmac_clk_get(priv))
> + priv->stmmac_clk = clk_get(priv->device, NULL);
> + if (IS_ERR(priv->stmmac_clk))
> pr_warning("%s: warning: cannot get CSR clock\n", __func__);
>
> /* If a specific clk_csr value is passed from the platform
> @@ -1934,10 +1938,12 @@ struct stmmac_priv *stmmac_dvr_probe(struct device *device,
> * set the MDC clock dynamically according to the csr actual
> * clock input.
> */
> - if (!priv->plat->clk_csr)
> - stmmac_clk_csr_set(priv);
> - else
> + if (!priv->plat->clk_csr) {
> + if (!IS_ERR(priv->stmmac_clk))
> + stmmac_clk_csr_set(priv);
> + } else {
> priv->clk_csr = priv->plat->clk_csr;
> + }
>
> /* MDIO bus Registration */
> ret = stmmac_mdio_register(ndev);
> @@ -2020,7 +2026,8 @@ int stmmac_suspend(struct net_device *ndev)
> else {
> stmmac_set_mac(priv->ioaddr, false);
> /* Disable clock in case of PWM is off */
> - stmmac_clk_disable(priv);
> + if (!IS_ERR(priv->stmmac_clk))
> + clk_disable(priv->stmmac_clk);
> }
> spin_unlock(&priv->lock);
> return 0;
> @@ -2042,9 +2049,9 @@ int stmmac_resume(struct net_device *ndev)
> * from another devices (e.g. serial console). */
> if (device_may_wakeup(priv->device))
> priv->hw->mac->pmt(priv->ioaddr, 0);
> - else
> + else if (!IS_ERR(priv->stmmac_clk))
> /* enable the clk prevously disabled */
> - stmmac_clk_enable(priv);
> + clk_enable(priv->stmmac_clk);
>
> netif_device_attach(ndev);
>
^ permalink raw reply [flat|nested] 14+ messages in thread* [PATCH V2 6/9] net/stmmac: Remove conditional compilation of clk code
2012-04-24 6:16 ` Giuseppe CAVALLARO
@ 2012-04-24 6:33 ` Giuseppe CAVALLARO
2012-04-24 6:42 ` Viresh Kumar
0 siblings, 1 reply; 14+ messages in thread
From: Giuseppe CAVALLARO @ 2012-04-24 6:33 UTC (permalink / raw)
To: linux-arm-kernel
On 4/24/2012 8:16 AM, Giuseppe CAVALLARO wrote:
> On 4/24/2012 7:56 AM, Viresh KUMAR wrote:
>> With addition of dummy clk_*() calls for non CONFIG_HAVE_CLK cases in clk.h,
>> there is no need to have clk code enclosed in #ifdef CONFIG_HAVE_CLK, #endif
>> macros.
>
> Hello Viresh
>
> patch only applies fine against the net-next repository so on top of the
> diver version: March_2012 and it builds fine on arch w/ w/o HAVE_CLK
> (just tested).
Oops, sorry but on a build I got:
CC init/version.o
LD init/built-in.o
LD .tmp_vmlinux1
drivers/built-in.o: In function `stmmac_release':
/stlinux/cavagiu/git/mirror/net-next.git/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1134:
undefined reference to `clk_disable'
drivers/built-in.o: In function `stmmac_open':
/stlinux/cavagiu/git/mirror/net-next.git/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:974:
undefined reference to `clk_enable'
/stlinux/cavagiu/git/mirror/net-next.git/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1079:
undefined reference to `clk_disable'
drivers/built-in.o: In function `stmmac_dvr_probe':
/stlinux/cavagiu/git/mirror/net-next.git/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1931:
undefined reference to `clk_get'
drivers/built-in.o: In function `stmmac_clk_csr_set':
/stlinux/cavagiu/git/mirror/net-next.git/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:174:
undefined reference to `clk_get_rate'
drivers/built-in.o: In function `stmmac_suspend':
/stlinux/cavagiu/git/mirror/net-next.git/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2030:
undefined reference to `clk_disable'
drivers/built-in.o: In function `stmmac_resume':
/stlinux/cavagiu/git/mirror/net-next.git/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2054:
undefined reference to `clk_enable'
make: *** [.tmp_vmlinux1] Error 1
Pls, can you verify?
Peppe
>
> Thanks a lot.
>
> Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
>
>> Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
>> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
>> Cc: David S. Miller <davem@davemloft.net>
>> ---
>> drivers/net/ethernet/stmicro/stmmac/stmmac.h | 41 ---------------------
>> drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 31 ++++++++++------
>> 2 files changed, 19 insertions(+), 53 deletions(-)
>>
>> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
>> index db2de9a..7f85895 100644
>> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h
>> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
>> @@ -81,9 +81,7 @@ struct stmmac_priv {
>> struct stmmac_counters mmc;
>> struct dma_features dma_cap;
>> int hw_cap_support;
>> -#ifdef CONFIG_HAVE_CLK
>> struct clk *stmmac_clk;
>> -#endif
>> int clk_csr;
>> };
>>
>> @@ -103,42 +101,3 @@ int stmmac_dvr_remove(struct net_device *ndev);
>> struct stmmac_priv *stmmac_dvr_probe(struct device *device,
>> struct plat_stmmacenet_data *plat_dat,
>> void __iomem *addr);
>> -
>> -#ifdef CONFIG_HAVE_CLK
>> -static inline int stmmac_clk_enable(struct stmmac_priv *priv)
>> -{
>> - if (!IS_ERR(priv->stmmac_clk))
>> - return clk_enable(priv->stmmac_clk);
>> -
>> - return 0;
>> -}
>> -
>> -static inline void stmmac_clk_disable(struct stmmac_priv *priv)
>> -{
>> - if (IS_ERR(priv->stmmac_clk))
>> - return;
>> -
>> - clk_disable(priv->stmmac_clk);
>> -}
>> -static inline int stmmac_clk_get(struct stmmac_priv *priv)
>> -{
>> - priv->stmmac_clk = clk_get(priv->device, NULL);
>> -
>> - if (IS_ERR(priv->stmmac_clk))
>> - return PTR_ERR(priv->stmmac_clk);
>> -
>> - return 0;
>> -}
>> -#else
>> -static inline int stmmac_clk_enable(struct stmmac_priv *priv)
>> -{
>> - return 0;
>> -}
>> -static inline void stmmac_clk_disable(struct stmmac_priv *priv)
>> -{
>> -}
>> -static inline int stmmac_clk_get(struct stmmac_priv *priv)
>> -{
>> - return 0;
>> -}
>> -#endif /* CONFIG_HAVE_CLK */
>> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
>> index 1a4cf81..18ce287 100644
>> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
>> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
>> @@ -28,6 +28,7 @@
>> https://bugzilla.stlinux.com/
>> *******************************************************************************/
>>
>> +#include <linux/clk.h>
>> #include <linux/kernel.h>
>> #include <linux/interrupt.h>
>> #include <linux/ip.h>
>> @@ -165,7 +166,6 @@ static void stmmac_verify_args(void)
>>
>> static void stmmac_clk_csr_set(struct stmmac_priv *priv)
>> {
>> -#ifdef CONFIG_HAVE_CLK
>> u32 clk_rate;
>>
>> if (IS_ERR(priv->stmmac_clk))
>> @@ -192,7 +192,6 @@ static void stmmac_clk_csr_set(struct stmmac_priv *priv)
>> * we can not estimate the proper divider as it is not known
>> * the frequency of clk_csr_i. So we do not change the default
>> * divider. */
>> -#endif
>> }
>>
>> #if defined(STMMAC_XMIT_DEBUG) || defined(STMMAC_RX_DEBUG)
>> @@ -971,7 +970,8 @@ static int stmmac_open(struct net_device *dev)
>> } else
>> priv->tm->enable = 1;
>> #endif
>> - stmmac_clk_enable(priv);
>> + if (!IS_ERR(priv->stmmac_clk))
>> + clk_enable(priv->stmmac_clk);
>>
>> stmmac_check_ether_addr(priv);
>>
>> @@ -1075,7 +1075,8 @@ open_error:
>> if (priv->phydev)
>> phy_disconnect(priv->phydev);
>>
>> - stmmac_clk_disable(priv);
>> + if (!IS_ERR(priv->stmmac_clk))
>> + clk_disable(priv->stmmac_clk);
>>
>> return ret;
>> }
>> @@ -1128,7 +1129,9 @@ static int stmmac_release(struct net_device *dev)
>> #ifdef CONFIG_STMMAC_DEBUG_FS
>> stmmac_exit_fs();
>> #endif
>> - stmmac_clk_disable(priv);
>> +
>> + if (!IS_ERR(priv->stmmac_clk))
>> + clk_disable(priv->stmmac_clk);
>>
>> return 0;
>> }
>> @@ -1925,7 +1928,8 @@ struct stmmac_priv *stmmac_dvr_probe(struct device *device,
>> goto error;
>> }
>>
>> - if (stmmac_clk_get(priv))
>> + priv->stmmac_clk = clk_get(priv->device, NULL);
>> + if (IS_ERR(priv->stmmac_clk))
>> pr_warning("%s: warning: cannot get CSR clock\n", __func__);
>>
>> /* If a specific clk_csr value is passed from the platform
>> @@ -1934,10 +1938,12 @@ struct stmmac_priv *stmmac_dvr_probe(struct device *device,
>> * set the MDC clock dynamically according to the csr actual
>> * clock input.
>> */
>> - if (!priv->plat->clk_csr)
>> - stmmac_clk_csr_set(priv);
>> - else
>> + if (!priv->plat->clk_csr) {
>> + if (!IS_ERR(priv->stmmac_clk))
>> + stmmac_clk_csr_set(priv);
>> + } else {
>> priv->clk_csr = priv->plat->clk_csr;
>> + }
>>
>> /* MDIO bus Registration */
>> ret = stmmac_mdio_register(ndev);
>> @@ -2020,7 +2026,8 @@ int stmmac_suspend(struct net_device *ndev)
>> else {
>> stmmac_set_mac(priv->ioaddr, false);
>> /* Disable clock in case of PWM is off */
>> - stmmac_clk_disable(priv);
>> + if (!IS_ERR(priv->stmmac_clk))
>> + clk_disable(priv->stmmac_clk);
>> }
>> spin_unlock(&priv->lock);
>> return 0;
>> @@ -2042,9 +2049,9 @@ int stmmac_resume(struct net_device *ndev)
>> * from another devices (e.g. serial console). */
>> if (device_may_wakeup(priv->device))
>> priv->hw->mac->pmt(priv->ioaddr, 0);
>> - else
>> + else if (!IS_ERR(priv->stmmac_clk))
>> /* enable the clk prevously disabled */
>> - stmmac_clk_enable(priv);
>> + clk_enable(priv->stmmac_clk);
>>
>> netif_device_attach(ndev);
>>
>
> --
> To unsubscribe from this list: send the line "unsubscribe netdev" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
^ permalink raw reply [flat|nested] 14+ messages in thread* [PATCH V2 6/9] net/stmmac: Remove conditional compilation of clk code
2012-04-24 6:33 ` Giuseppe CAVALLARO
@ 2012-04-24 6:42 ` Viresh Kumar
2012-04-24 8:24 ` Giuseppe CAVALLARO
0 siblings, 1 reply; 14+ messages in thread
From: Viresh Kumar @ 2012-04-24 6:42 UTC (permalink / raw)
To: linux-arm-kernel
On 4/24/2012 12:03 PM, Giuseppe CAVALLARO wrote:
> Oops, sorry but on a build I got:
>
> CC init/version.o
> LD init/built-in.o
> LD .tmp_vmlinux1
> drivers/built-in.o: In function `stmmac_release':
> /stlinux/cavagiu/git/mirror/net-next.git/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1134:
> undefined reference to `clk_disable'
> drivers/built-in.o: In function `stmmac_open':
> /stlinux/cavagiu/git/mirror/net-next.git/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:974:
> undefined reference to `clk_enable'
> /stlinux/cavagiu/git/mirror/net-next.git/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1079:
> undefined reference to `clk_disable'
> drivers/built-in.o: In function `stmmac_dvr_probe':
> /stlinux/cavagiu/git/mirror/net-next.git/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1931:
> undefined reference to `clk_get'
> drivers/built-in.o: In function `stmmac_clk_csr_set':
> /stlinux/cavagiu/git/mirror/net-next.git/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:174:
> undefined reference to `clk_get_rate'
> drivers/built-in.o: In function `stmmac_suspend':
> /stlinux/cavagiu/git/mirror/net-next.git/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2030:
> undefined reference to `clk_disable'
> drivers/built-in.o: In function `stmmac_resume':
> /stlinux/cavagiu/git/mirror/net-next.git/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2054:
> undefined reference to `clk_enable'
> make: *** [.tmp_vmlinux1] Error 1
>
> Pls, can you verify?
I believe, you haven't applied:
[PATCH V2 1/9] clk: Add non CONFIG_HAVE_CLK routines
which must be applied before testing this.
--
viresh
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH V2 6/9] net/stmmac: Remove conditional compilation of clk code
2012-04-24 6:42 ` Viresh Kumar
@ 2012-04-24 8:24 ` Giuseppe CAVALLARO
0 siblings, 0 replies; 14+ messages in thread
From: Giuseppe CAVALLARO @ 2012-04-24 8:24 UTC (permalink / raw)
To: linux-arm-kernel
On 4/24/2012 8:42 AM, Viresh Kumar wrote:
> On 4/24/2012 12:03 PM, Giuseppe CAVALLARO wrote:
>> Oops, sorry but on a build I got:
>>
>> CC init/version.o
>> LD init/built-in.o
>> LD .tmp_vmlinux1
>> drivers/built-in.o: In function `stmmac_release':
>> /stlinux/cavagiu/git/mirror/net-next.git/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1134:
>> undefined reference to `clk_disable'
>> drivers/built-in.o: In function `stmmac_open':
>> /stlinux/cavagiu/git/mirror/net-next.git/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:974:
>> undefined reference to `clk_enable'
>> /stlinux/cavagiu/git/mirror/net-next.git/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1079:
>> undefined reference to `clk_disable'
>> drivers/built-in.o: In function `stmmac_dvr_probe':
>> /stlinux/cavagiu/git/mirror/net-next.git/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1931:
>> undefined reference to `clk_get'
>> drivers/built-in.o: In function `stmmac_clk_csr_set':
>> /stlinux/cavagiu/git/mirror/net-next.git/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:174:
>> undefined reference to `clk_get_rate'
>> drivers/built-in.o: In function `stmmac_suspend':
>> /stlinux/cavagiu/git/mirror/net-next.git/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2030:
>> undefined reference to `clk_disable'
>> drivers/built-in.o: In function `stmmac_resume':
>> /stlinux/cavagiu/git/mirror/net-next.git/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2054:
>> undefined reference to `clk_enable'
>> make: *** [.tmp_vmlinux1] Error 1
>>
>> Pls, can you verify?
>
> I believe, you haven't applied:
>
> [PATCH V2 1/9] clk: Add non CONFIG_HAVE_CLK routines
>
> which must be applied before testing this.
Yes with it applied the build is ok.
Peppe
>
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH V2 7/9] gadget/m66592: Remove conditional compilation of clk code
2012-04-24 5:56 [PATCH V2 0/9] clk: Add non CONFIG_HAVE_CLK routines Viresh Kumar
` (5 preceding siblings ...)
2012-04-24 5:56 ` [PATCH V2 6/9] net/stmmac: " Viresh Kumar
@ 2012-04-24 5:56 ` Viresh Kumar
2012-04-24 5:56 ` [PATCH V2 8/9] gadget/r8a66597: " Viresh Kumar
2012-04-24 5:56 ` [PATCH V2 9/9] usb/host/r8a66597: " Viresh Kumar
8 siblings, 0 replies; 14+ messages in thread
From: Viresh Kumar @ 2012-04-24 5:56 UTC (permalink / raw)
To: linux-arm-kernel
With addition of dummy clk_*() calls for non CONFIG_HAVE_CLK cases in clk.h,
there is no need to have clk code enclosed in #ifdef CONFIG_HAVE_CLK, #endif
macros.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb at vger.kernel.org
---
drivers/usb/gadget/m66592-udc.c | 19 +++++--------------
drivers/usb/gadget/m66592-udc.h | 5 -----
2 files changed, 5 insertions(+), 19 deletions(-)
diff --git a/drivers/usb/gadget/m66592-udc.c b/drivers/usb/gadget/m66592-udc.c
index 3608b3b..34eee07 100644
--- a/drivers/usb/gadget/m66592-udc.c
+++ b/drivers/usb/gadget/m66592-udc.c
@@ -1583,12 +1583,10 @@ static int __exit m66592_remove(struct platform_device *pdev)
iounmap(m66592->reg);
free_irq(platform_get_irq(pdev, 0), m66592);
m66592_free_request(&m66592->ep[0].ep, m66592->ep0_req);
-#ifdef CONFIG_HAVE_CLK
- if (m66592->pdata->on_chip) {
+ if (m66592->pdata->on_chip && !IS_ERR(m66592->clk)) {
clk_disable(m66592->clk);
clk_put(m66592->clk);
}
-#endif
kfree(m66592);
return 0;
}
@@ -1602,9 +1600,7 @@ static int __init m66592_probe(struct platform_device *pdev)
struct resource *res, *ires;
void __iomem *reg = NULL;
struct m66592 *m66592 = NULL;
-#ifdef CONFIG_HAVE_CLK
char clk_name[8];
-#endif
int ret = 0;
int i;
@@ -1671,19 +1667,17 @@ static int __init m66592_probe(struct platform_device *pdev)
goto clean_up;
}
-#ifdef CONFIG_HAVE_CLK
if (m66592->pdata->on_chip) {
snprintf(clk_name, sizeof(clk_name), "usbf%d", pdev->id);
m66592->clk = clk_get(&pdev->dev, clk_name);
if (IS_ERR(m66592->clk)) {
dev_err(&pdev->dev, "cannot get clock \"%s\"\n",
clk_name);
- ret = PTR_ERR(m66592->clk);
- goto clean_up2;
+ } else {
+ clk_enable(m66592->clk);
}
- clk_enable(m66592->clk);
}
-#endif
+
INIT_LIST_HEAD(&m66592->gadget.ep_list);
m66592->gadget.ep0 = &m66592->ep[0].ep;
INIT_LIST_HEAD(&m66592->gadget.ep0->ep_list);
@@ -1731,13 +1725,10 @@ err_add_udc:
m66592_free_request(&m66592->ep[0].ep, m66592->ep0_req);
clean_up3:
-#ifdef CONFIG_HAVE_CLK
- if (m66592->pdata->on_chip) {
+ if (m66592->pdata->on_chip && !IS_ERR(m66592->clk)) {
clk_disable(m66592->clk);
clk_put(m66592->clk);
}
-clean_up2:
-#endif
free_irq(ires->start, m66592);
clean_up:
if (m66592) {
diff --git a/drivers/usb/gadget/m66592-udc.h b/drivers/usb/gadget/m66592-udc.h
index 9d9f7e3..a044ad3 100644
--- a/drivers/usb/gadget/m66592-udc.h
+++ b/drivers/usb/gadget/m66592-udc.h
@@ -13,10 +13,7 @@
#ifndef __M66592_UDC_H__
#define __M66592_UDC_H__
-#ifdef CONFIG_HAVE_CLK
#include <linux/clk.h>
-#endif
-
#include <linux/usb/m66592.h>
#define M66592_SYSCFG 0x00
@@ -468,9 +465,7 @@ struct m66592_ep {
struct m66592 {
spinlock_t lock;
void __iomem *reg;
-#ifdef CONFIG_HAVE_CLK
struct clk *clk;
-#endif
struct m66592_platdata *pdata;
unsigned long irq_trigger;
--
1.7.9
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH V2 8/9] gadget/r8a66597: Remove conditional compilation of clk code
2012-04-24 5:56 [PATCH V2 0/9] clk: Add non CONFIG_HAVE_CLK routines Viresh Kumar
` (6 preceding siblings ...)
2012-04-24 5:56 ` [PATCH V2 7/9] gadget/m66592: " Viresh Kumar
@ 2012-04-24 5:56 ` Viresh Kumar
2012-04-24 5:56 ` [PATCH V2 9/9] usb/host/r8a66597: " Viresh Kumar
8 siblings, 0 replies; 14+ messages in thread
From: Viresh Kumar @ 2012-04-24 5:56 UTC (permalink / raw)
To: linux-arm-kernel
With addition of dummy clk_*() calls for non CONFIG_HAVE_CLK cases in clk.h,
there is no need to have clk code enclosed in #ifdef CONFIG_HAVE_CLK, #endif
macros.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb at vger.kernel.org
---
drivers/usb/gadget/r8a66597-udc.c | 21 +++++++--------------
drivers/usb/gadget/r8a66597-udc.h | 5 -----
2 files changed, 7 insertions(+), 19 deletions(-)
diff --git a/drivers/usb/gadget/r8a66597-udc.c b/drivers/usb/gadget/r8a66597-udc.c
index c4401e7..85aa56d 100644
--- a/drivers/usb/gadget/r8a66597-udc.c
+++ b/drivers/usb/gadget/r8a66597-udc.c
@@ -1818,12 +1818,11 @@ static int __exit r8a66597_remove(struct platform_device *pdev)
iounmap(r8a66597->sudmac_reg);
free_irq(platform_get_irq(pdev, 0), r8a66597);
r8a66597_free_request(&r8a66597->ep[0].ep, r8a66597->ep0_req);
-#ifdef CONFIG_HAVE_CLK
- if (r8a66597->pdata->on_chip) {
+
+ if (r8a66597->pdata->on_chip && !IS_ERR(r8a66597->clk)) {
clk_disable(r8a66597->clk);
clk_put(r8a66597->clk);
}
-#endif
device_unregister(&r8a66597->gadget.dev);
kfree(r8a66597);
return 0;
@@ -1855,9 +1854,7 @@ static int __init r8a66597_sudmac_ioremap(struct r8a66597 *r8a66597,
static int __init r8a66597_probe(struct platform_device *pdev)
{
-#ifdef CONFIG_HAVE_CLK
char clk_name[8];
-#endif
struct resource *res, *ires;
int irq;
void __iomem *reg = NULL;
@@ -1921,19 +1918,17 @@ static int __init r8a66597_probe(struct platform_device *pdev)
r8a66597->timer.data = (unsigned long)r8a66597;
r8a66597->reg = reg;
-#ifdef CONFIG_HAVE_CLK
if (r8a66597->pdata->on_chip) {
snprintf(clk_name, sizeof(clk_name), "usb%d", pdev->id);
r8a66597->clk = clk_get(&pdev->dev, clk_name);
if (IS_ERR(r8a66597->clk)) {
dev_err(&pdev->dev, "cannot get clock \"%s\"\n",
clk_name);
- ret = PTR_ERR(r8a66597->clk);
- goto clean_up_dev;
+ } else {
+ clk_enable(r8a66597->clk);
}
- clk_enable(r8a66597->clk);
}
-#endif
+
if (r8a66597->pdata->sudmac) {
ret = r8a66597_sudmac_ioremap(r8a66597, pdev);
if (ret < 0)
@@ -1993,13 +1988,11 @@ err_add_udc:
clean_up3:
free_irq(irq, r8a66597);
clean_up2:
-#ifdef CONFIG_HAVE_CLK
- if (r8a66597->pdata->on_chip) {
+ if (r8a66597->pdata->on_chip && !IS_ERR(r8a66597->clk)) {
clk_disable(r8a66597->clk);
clk_put(r8a66597->clk);
}
-clean_up_dev:
-#endif
+
device_unregister(&r8a66597->gadget.dev);
clean_up:
if (r8a66597) {
diff --git a/drivers/usb/gadget/r8a66597-udc.h b/drivers/usb/gadget/r8a66597-udc.h
index 8e3de61..d2a5ad2 100644
--- a/drivers/usb/gadget/r8a66597-udc.h
+++ b/drivers/usb/gadget/r8a66597-udc.h
@@ -13,10 +13,7 @@
#ifndef __R8A66597_H__
#define __R8A66597_H__
-#ifdef CONFIG_HAVE_CLK
#include <linux/clk.h>
-#endif
-
#include <linux/usb/r8a66597.h>
#define R8A66597_MAX_SAMPLING 10
@@ -92,9 +89,7 @@ struct r8a66597 {
void __iomem *reg;
void __iomem *sudmac_reg;
-#ifdef CONFIG_HAVE_CLK
struct clk *clk;
-#endif
struct r8a66597_platdata *pdata;
struct usb_gadget gadget;
--
1.7.9
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH V2 9/9] usb/host/r8a66597: Remove conditional compilation of clk code
2012-04-24 5:56 [PATCH V2 0/9] clk: Add non CONFIG_HAVE_CLK routines Viresh Kumar
` (7 preceding siblings ...)
2012-04-24 5:56 ` [PATCH V2 8/9] gadget/r8a66597: " Viresh Kumar
@ 2012-04-24 5:56 ` Viresh Kumar
8 siblings, 0 replies; 14+ messages in thread
From: Viresh Kumar @ 2012-04-24 5:56 UTC (permalink / raw)
To: linux-arm-kernel
With addition of dummy clk_*() calls for non CONFIG_HAVE_CLK cases in clk.h,
there is no need to have clk code enclosed in #ifdef CONFIG_HAVE_CLK, #endif
macros.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb at vger.kernel.org
---
drivers/usb/host/r8a66597-hcd.c | 28 +++++++++-------------------
drivers/usb/host/r8a66597.h | 5 -----
2 files changed, 9 insertions(+), 24 deletions(-)
diff --git a/drivers/usb/host/r8a66597-hcd.c b/drivers/usb/host/r8a66597-hcd.c
index 2bf1320..6d11553 100644
--- a/drivers/usb/host/r8a66597-hcd.c
+++ b/drivers/usb/host/r8a66597-hcd.c
@@ -95,9 +95,9 @@ static int r8a66597_clock_enable(struct r8a66597 *r8a66597)
int i = 0;
if (r8a66597->pdata->on_chip) {
-#ifdef CONFIG_HAVE_CLK
- clk_enable(r8a66597->clk);
-#endif
+ if (!IS_ERR(r8a66597->clk))
+ clk_enable(r8a66597->clk);
+
do {
r8a66597_write(r8a66597, SCKE, SYSCFG0);
tmp = r8a66597_read(r8a66597, SYSCFG0);
@@ -141,9 +141,8 @@ static void r8a66597_clock_disable(struct r8a66597 *r8a66597)
udelay(1);
if (r8a66597->pdata->on_chip) {
-#ifdef CONFIG_HAVE_CLK
- clk_disable(r8a66597->clk);
-#endif
+ if (!IS_ERR(r8a66597->clk))
+ clk_disable(r8a66597->clk);
} else {
r8a66597_bclr(r8a66597, PLLC, SYSCFG0);
r8a66597_bclr(r8a66597, XCKE, SYSCFG0);
@@ -2406,19 +2405,16 @@ static int __devexit r8a66597_remove(struct platform_device *pdev)
del_timer_sync(&r8a66597->rh_timer);
usb_remove_hcd(hcd);
iounmap(r8a66597->reg);
-#ifdef CONFIG_HAVE_CLK
- if (r8a66597->pdata->on_chip)
+ if (r8a66597->pdata->on_chip && !IS_ERR(r8a66597->clk))
clk_put(r8a66597->clk);
-#endif
+
usb_put_hcd(hcd);
return 0;
}
static int __devinit r8a66597_probe(struct platform_device *pdev)
{
-#ifdef CONFIG_HAVE_CLK
char clk_name[8];
-#endif
struct resource *res = NULL, *ires;
int irq = -1;
void __iomem *reg = NULL;
@@ -2482,16 +2478,12 @@ static int __devinit r8a66597_probe(struct platform_device *pdev)
r8a66597->irq_sense_low = irq_trigger == IRQF_TRIGGER_LOW;
if (r8a66597->pdata->on_chip) {
-#ifdef CONFIG_HAVE_CLK
snprintf(clk_name, sizeof(clk_name), "usb%d", pdev->id);
r8a66597->clk = clk_get(&pdev->dev, clk_name);
if (IS_ERR(r8a66597->clk)) {
dev_err(&pdev->dev, "cannot get clock \"%s\"\n",
clk_name);
- ret = PTR_ERR(r8a66597->clk);
- goto clean_up2;
}
-#endif
r8a66597->max_root_hub = 1;
} else
r8a66597->max_root_hub = 2;
@@ -2531,11 +2523,9 @@ static int __devinit r8a66597_probe(struct platform_device *pdev)
return 0;
clean_up3:
-#ifdef CONFIG_HAVE_CLK
- if (r8a66597->pdata->on_chip)
+ if (r8a66597->pdata->on_chip && !IS_ERR(r8a66597->clk))
clk_put(r8a66597->clk);
-clean_up2:
-#endif
+
usb_put_hcd(hcd);
clean_up:
diff --git a/drivers/usb/host/r8a66597.h b/drivers/usb/host/r8a66597.h
index f28782d..672cea3 100644
--- a/drivers/usb/host/r8a66597.h
+++ b/drivers/usb/host/r8a66597.h
@@ -26,10 +26,7 @@
#ifndef __R8A66597_H__
#define __R8A66597_H__
-#ifdef CONFIG_HAVE_CLK
#include <linux/clk.h>
-#endif
-
#include <linux/usb/r8a66597.h>
#define R8A66597_MAX_NUM_PIPE 10
@@ -113,9 +110,7 @@ struct r8a66597_root_hub {
struct r8a66597 {
spinlock_t lock;
void __iomem *reg;
-#ifdef CONFIG_HAVE_CLK
struct clk *clk;
-#endif
struct r8a66597_platdata *pdata;
struct r8a66597_device device0;
struct r8a66597_root_hub root_hub[R8A66597_MAX_ROOT_HUB];
--
1.7.9
^ permalink raw reply related [flat|nested] 14+ messages in thread