[PATCH 0/6] at91: some fixes for 3.8-rc5

[PATCH 0/6] at91: some fixes for 3.8-rc5

[Nicolas Ferre]

Hi all,

I try to collect fixes for AT91 that can be applied during this development
cycle. Please tell me now if you have more to queue or if some of the proposed
fixes are not targetted to v3.8-final in you opinion...

Thanks, cheers,


Boris BREZILLON (1):
  ARM: at91/dts: add macb mii pinctrl config for kizbox

Jean-Christophe PLAGNIOL-VILLARD (1):
  ARM: at91: rm9200: remake the BGA as default version

Joachim Eastwood (1):
  ARM: at91: fix gpios on i2c-gpio for RM9200 DT

Richard Genoud (3):
  ARM: at91/at91-pinctrl documentation: fix typo and add some details
  ARM: at91/at91sam9x5 DTS: correct wrong PIO BANK values on u(s)arts
  ARM: at91/at91sam9x5 DTS: add SCK USART pins

 .../bindings/pinctrl/atmel,at91-pinctrl.txt        |  5 ++-
 arch/arm/boot/dts/at91rm9200.dtsi                  |  4 +-
 arch/arm/boot/dts/at91sam9x5.dtsi                  | 44 ++++++++++++++++------
 arch/arm/boot/dts/kizbox.dts                       |  2 +
 arch/arm/mach-at91/setup.c                         |  2 +
 5 files changed, 41 insertions(+), 16 deletions(-)

-- 
1.8.0

[PATCH 1/6] ARM: at91/at91-pinctrl documentation: fix typo and add some details

[Nicolas Ferre]

From: Richard Genoud <richard.genoud@gmail.com>

The relation between PIN_BANK numbers and pio letters wasn't made very
clear.

Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
---
 Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
index 3a26812..bc50899 100644
--- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
@@ -81,7 +81,8 @@ PA31	TXD4
 Required properties for pin configuration node:
 - atmel,pins: 4 integers array, represents a group of pins mux and config
   setting. The format is atmel,pins = <PIN_BANK PIN_BANK_NUM PERIPH CONFIG>.
-  The PERIPH 0 means gpio.
+  The PERIPH 0 means gpio, PERIPH 1 is periph A, PERIPH 2 is periph B...
+  PIN_BANK 0 is pioA, PIN_BANK 1 is pioB...
 
 Bits used for CONFIG:
 PULL_UP		(1 << 0): indicate this pin need a pull up.
@@ -126,7 +127,7 @@ pinctrl@fffff400 {
 		pinctrl_dbgu: dbgu-0 {
 			atmel,pins =
 				<1 14 0x1 0x0	/* PB14 periph A */
-				 1 15 0x1 0x1>;	/* PB15 periph with pullup */
+				 1 15 0x1 0x1>;	/* PB15 periph A with pullup */
 		};
 	};
 };
-- 
1.8.0

[PATCH 2/6] ARM: at91/at91sam9x5 DTS: correct wrong PIO BANK values on u(s)arts

[Nicolas Ferre]

From: Richard Genoud <richard.genoud@gmail.com>

The PIN_BANK 3 is for PDxx pins, not PCxx pins.
And PIN_BANK 1 is for PBxx, not PIN_BANK 0.

Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
---
 arch/arm/boot/dts/at91sam9x5.dtsi | 24 ++++++++++++------------
 1 file changed, 12 insertions(+), 12 deletions(-)

diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi
index 3a47cf9..e9c4290 100644
--- a/arch/arm/boot/dts/at91sam9x5.dtsi
+++ b/arch/arm/boot/dts/at91sam9x5.dtsi
@@ -154,12 +154,12 @@
 
 					pinctrl_usart1_rts: usart1_rts-0 {
 						atmel,pins =
-							<3 27 0x3 0x0>;	/* PC27 periph C */
+							<2 27 0x3 0x0>;	/* PC27 periph C */
 					};
 
 					pinctrl_usart1_cts: usart1_cts-0 {
 						atmel,pins =
-							<3 28 0x3 0x0>;	/* PC28 periph C */
+							<2 28 0x3 0x0>;	/* PC28 periph C */
 					};
 				};
 
@@ -172,46 +172,46 @@
 
 					pinctrl_uart2_rts: uart2_rts-0 {
 						atmel,pins =
-							<0 0 0x2 0x0>;	/* PB0 periph B */
+							<1 0 0x2 0x0>;	/* PB0 periph B */
 					};
 
 					pinctrl_uart2_cts: uart2_cts-0 {
 						atmel,pins =
-							<0 1 0x2 0x0>;	/* PB1 periph B */
+							<1 1 0x2 0x0>;	/* PB1 periph B */
 					};
 				};
 
 				usart3 {
 					pinctrl_uart3: usart3-0 {
 						atmel,pins =
-							<3 23 0x2 0x1	/* PC22 periph B with pullup */
-							 3 23 0x2 0x0>;	/* PC23 periph B */
+							<2 23 0x2 0x1	/* PC22 periph B with pullup */
+							 2 23 0x2 0x0>;	/* PC23 periph B */
 					};
 
 					pinctrl_usart3_rts: usart3_rts-0 {
 						atmel,pins =
-							<3 24 0x2 0x0>;	/* PC24 periph B */
+							<2 24 0x2 0x0>;	/* PC24 periph B */
 					};
 
 					pinctrl_usart3_cts: usart3_cts-0 {
 						atmel,pins =
-							<3 25 0x2 0x0>;	/* PC25 periph B */
+							<2 25 0x2 0x0>;	/* PC25 periph B */
 					};
 				};
 
 				uart0 {
 					pinctrl_uart0: uart0-0 {
 						atmel,pins =
-							<3 8 0x3 0x0	/* PC8 periph C */
-							 3 9 0x3 0x1>;	/* PC9 periph C with pullup */
+							<2 8 0x3 0x0	/* PC8 periph C */
+							 2 9 0x3 0x1>;	/* PC9 periph C with pullup */
 					};
 				};
 
 				uart1 {
 					pinctrl_uart1: uart1-0 {
 						atmel,pins =
-							<3 16 0x3 0x0	/* PC16 periph C */
-							 3 17 0x3 0x1>;	/* PC17 periph C with pullup */
+							<2 16 0x3 0x0	/* PC16 periph C */
+							 2 17 0x3 0x1>;	/* PC17 periph C with pullup */
 					};
 				};
 
-- 
1.8.0

[PATCH 3/6] ARM: at91/at91sam9x5 DTS: add SCK USART pins

[Nicolas Ferre]

From: Richard Genoud <richard.genoud@gmail.com>

The SCK pins where missing in usarts pinctrl.

Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
---
 arch/arm/boot/dts/at91sam9x5.dtsi | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi
index e9c4290..cb711a5 100644
--- a/arch/arm/boot/dts/at91sam9x5.dtsi
+++ b/arch/arm/boot/dts/at91sam9x5.dtsi
@@ -143,6 +143,11 @@
 						atmel,pins =
 							<0 3 0x1 0x0>;	/* PA3 periph A */
 					};
+
+					pinctrl_usart0_sck: usart0_sck-0 {
+						atmel,pins =
+							<0 4 0x1 0x0>;	/* PA4 periph A */
+					};
 				};
 
 				usart1 {
@@ -161,6 +166,11 @@
 						atmel,pins =
 							<2 28 0x3 0x0>;	/* PC28 periph C */
 					};
+
+					pinctrl_usart1_sck: usart1_sck-0 {
+						atmel,pins =
+							<2 28 0x3 0x0>;	/* PC29 periph C */
+					};
 				};
 
 				usart2 {
@@ -179,6 +189,11 @@
 						atmel,pins =
 							<1 1 0x2 0x0>;	/* PB1 periph B */
 					};
+
+					pinctrl_usart2_sck: usart2_sck-0 {
+						atmel,pins =
+							<1 2 0x2 0x0>;	/* PB2 periph B */
+					};
 				};
 
 				usart3 {
@@ -197,6 +212,11 @@
 						atmel,pins =
 							<2 25 0x2 0x0>;	/* PC25 periph B */
 					};
+
+					pinctrl_usart3_sck: usart3_sck-0 {
+						atmel,pins =
+							<2 26 0x2 0x0>;	/* PC26 periph B */
+					};
 				};
 
 				uart0 {
-- 
1.8.0

[PATCH 4/6] ARM: at91: fix gpios on i2c-gpio for RM9200 DT

[Nicolas Ferre]

From: Joachim Eastwood <manabian@gmail.com>

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
---
 arch/arm/boot/dts/at91rm9200.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/at91rm9200.dtsi b/arch/arm/boot/dts/at91rm9200.dtsi
index e154f24..222047f 100644
--- a/arch/arm/boot/dts/at91rm9200.dtsi
+++ b/arch/arm/boot/dts/at91rm9200.dtsi
@@ -336,8 +336,8 @@
 
 	i2c at 0 {
 		compatible = "i2c-gpio";
-		gpios = <&pioA 23 0 /* sda */
-			 &pioA 24 0 /* scl */
+		gpios = <&pioA 25 0 /* sda */
+			 &pioA 26 0 /* scl */
 			>;
 		i2c-gpio,sda-open-drain;
 		i2c-gpio,scl-open-drain;
-- 
1.8.0

[PATCH 5/6] ARM: at91: rm9200: remake the BGA as default version

[Nicolas Ferre]

From: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Make BGA as the default version as we are supposed to just have
to specify when we use the PQFP version.

Issue was existing since commit:
3e90772 (ARM: at91: fix at91rm9200 soc subtype handling).

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org> [v3.3]
---
 arch/arm/mach-at91/setup.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm/mach-at91/setup.c b/arch/arm/mach-at91/setup.c
index 9ee866c..4b67847 100644
--- a/arch/arm/mach-at91/setup.c
+++ b/arch/arm/mach-at91/setup.c
@@ -105,6 +105,8 @@ static void __init soc_detect(u32 dbgu_base)
 	switch (socid) {
 	case ARCH_ID_AT91RM9200:
 		at91_soc_initdata.type = AT91_SOC_RM9200;
+		if (at91_soc_initdata.subtype == AT91_SOC_SUBTYPE_NONE)
+			at91_soc_initdata.subtype = AT91_SOC_RM9200_BGA;
 		at91_boot_soc = at91rm9200_soc;
 		break;
 
-- 
1.8.0

[PATCH 6/6] ARM: at91/dts: add macb mii pinctrl config for kizbox

[Nicolas Ferre]

From: Boris BREZILLON <linux-arm@overkiz.com>

This patch overrides default macb pinctrl config defined in
at91sam9260.dtsi (pinctrl_macb_rmii) with kizbox board config
(pinctrl_macb_rmii + pinctrl_macb_rmii_mii_alt).

Signed-off-by: Boris BREZILLON <linux-arm@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
---
 arch/arm/boot/dts/kizbox.dts | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm/boot/dts/kizbox.dts b/arch/arm/boot/dts/kizbox.dts
index e8814fe..b4dc3ed 100644
--- a/arch/arm/boot/dts/kizbox.dts
+++ b/arch/arm/boot/dts/kizbox.dts
@@ -48,6 +48,8 @@
 
 			macb0: ethernet at fffc4000 {
 				phy-mode = "mii";
+				pinctrl-0 = <&pinctrl_macb_rmii
+				             &pinctrl_macb_rmii_mii_alt>;
 				status = "okay";
 			};
 
-- 
1.8.0

[PATCH 0/6] at91: some fixes for 3.8-rc5

[Jean-Christophe PLAGNIOL-VILLARD]

On 18:50 Tue 22 Jan     , Nicolas Ferre wrote:
> Hi all,
> 
> I try to collect fixes for AT91 that can be applied during this development
> cycle. Please tell me now if you have more to queue or if some of the proposed
> fixes are not targetted to v3.8-final in you opinion...
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Best Regards,
J.