* [PATCH 3/3] ARM: dts: imx6: Add support for imx6q dmo edmqmx6
2013-11-02 7:29 [PATCH 0/3] add support for i.MX6 based cpu modul dmo edmqmx6 Silvio F
2013-11-02 7:29 ` [PATCH 1/3] DT: sort vendor-prefixes.txt Silvio F
2013-11-02 7:29 ` [PATCH 2/3] DT: Add Data Modul vendor prefix Silvio F
@ 2013-11-02 7:29 ` Silvio F
2 siblings, 0 replies; 4+ messages in thread
From: Silvio F @ 2013-11-02 7:29 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Silvio F <silvio.fricke@gmail.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts | 163 ++++++++++++++++++++++++++++++++
2 files changed, 164 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 5468d2d..3159ab6 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -143,6 +143,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
imx6dl-wandboard.dtb \
imx6q-arm2.dtb \
imx6q-cm-fx6.dtb \
+ imx6q-dmo-edmqmx6.dtb \
imx6q-gw51xx.dtb \
imx6q-gw52xx.dtb \
imx6q-gw53xx.dtb \
diff --git a/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts b/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts
new file mode 100644
index 0000000..41ae4b1
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts
@@ -0,0 +1,163 @@
+/*
+ * Copyright 2013 Data Modul AG
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+
+/ {
+ model = "Data Modul eDM-QMX6 Board";
+ compatible = "dmo,imx6q-edmqmx6", "fsl,imx6q";
+
+ aliases {
+ gpio7 = &stmpe_gpio_1;
+ gpio8 = &stmpe_gpio_2;
+ };
+
+ memory {
+ reg = <0x10000000 0x80000000>;
+ };
+
+ regulators {
+ compatible = "simple-bus";
+
+ reg_3p3v: 3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_usb_otg_vbus: usb_otg_vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio7 12 0>;
+ };
+
+ reg_usb_host1: usb_host1_en {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_host1_en";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 31 0>;
+ enable-active-high;
+ };
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet_1>;
+ phy-mode = "rgmii";
+ phy-reset-gpios = <&gpio3 23 0>;
+ status = "okay";
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2_3
+ &pinctrl_stmpe_1_1
+ &pinctrl_stmpe_2_1>;
+ status = "okay";
+
+ stmpe1: stmpe1601 at 40 {
+ compatible = "st,stmpe1601";
+ reg = <0x40>;
+ interrupts = <30 0>;
+ interrupt-parent = <&gpio3>;
+
+ stmpe_gpio_1: stmpe_gpio {
+ compatible = "st,stmpe-gpio";
+ };
+ };
+
+ stmpe2: stmpe1601 at 44 {
+ compatible = "st,stmpe1601";
+ reg = <0x44>;
+ interrupts = <2 0>;
+ interrupt-parent = <&gpio5>;
+
+ stmpe_gpio_2: stmpe_gpio {
+ compatible = "st,stmpe-gpio";
+ };
+ };
+
+ temp1: ad7414 at 4c {
+ compatible = "ad,ad7414";
+ reg = <0x4c>;
+ };
+
+ temp2: ad7414 at 4d {
+ compatible = "ad,ad7414";
+ reg = <0x4d>;
+ };
+
+ rtc: m41t62 at 68 {
+ compatible = "stm,m41t62";
+ reg = <0x68>;
+ };
+};
+
+&iomuxc {
+ stmpe1 {
+ pinctrl_stmpe_1_1: stmpe1grp-1 {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x80000000
+ >;
+ };
+ };
+
+ stmpe2 {
+ pinctrl_stmpe_2_1: stmpe2grp-1 {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x80000000
+ >;
+ };
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1_2>;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2_1>;
+};
+
+&usbh1 {
+ vbus-supply = <®_usb_host1>;
+ status = "okay";
+ disable-over-current;
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg_1>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3_2>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+};
+
--
1.8.4
^ permalink raw reply related [flat|nested] 4+ messages in thread