* [PATCH v5 2/3] mfd: devicetree: add bindings for Atmel Flexcom
2015-07-21 14:21 [PATCH v5 0/3] mfd: flexcom: add a driver for Flexcom Cyrille Pitchen
2015-07-21 14:21 ` [PATCH v5 1/3] mfd: atmel-flexcom: create include file with macros used by DT bindings Cyrille Pitchen
@ 2015-07-21 14:21 ` Cyrille Pitchen
2015-07-21 14:21 ` [PATCH v5 3/3] mfd: atmel-flexcom: add a driver for Atmel Flexible Serial Communication Unit Cyrille Pitchen
2 siblings, 0 replies; 4+ messages in thread
From: Cyrille Pitchen @ 2015-07-21 14:21 UTC (permalink / raw)
To: linux-arm-kernel
This patch documents the DT bindings for the Atmel Flexcom which will be
introduced by sama5d2x SoCs. These bindings will be used by the actual
Flexcom driver to be sent in another patch.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
.../devicetree/bindings/mfd/atmel-flexcom.txt | 67 ++++++++++++++++++++++
1 file changed, 67 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
diff --git a/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt b/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
new file mode 100644
index 000000000000..9d448088e751
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
@@ -0,0 +1,67 @@
+* Device tree bindings for Atmel Flexcom (Flexible Serial Communication Unit)
+
+The Atmel Flexcom is just a wrapper which embeds a SPI controller, an I2C
+controller and an USART. Only one function can be used at a time and is chosen
+at boot time according to the device tree.
+
+Required properties:
+- compatible: "atmel,sama5d2-flexcom"
+- reg: shall be the offset/length value for Flexcom dedicated
+ I/O registers (without USART, TWI or SPI registers).
+- clocks: shall be the Flexcom peripheral clock from PMC.
+- #address-cells: should be <1>
+- #size-cells: should be <1>
+- ranges: one range for the full I/O register region (including
+ USART, TWI and SPI registers).
+- atmel,flexcom-mode: should be one of the 3 following macros as defined in
+ include/dt-bindings/mfd/atmel-flexcom.h:
+ - ATMEL_FLEXCOM_MODE_USART for USART
+ - ATMEL_FLEXCOM_MODE_SPI for SPI
+ - ATMEL_FLEXCOM_MODE_TWI for I2C
+
+Required child:
+a single child device of type matching the "atmel,flexcom-mode" property.
+
+The reg property of this child should be:
+- <0x200 0x200> for USART
+- <0x400 0x200> for SPI
+- <0x600 0x200> for I2C
+
+The phandle provided by the clocks property of the child is the same as one for
+the Flexcom parent.
+
+Other properties remain unchanged. See documentation of the respective device:
+- ../serial/atmel-usart.txt
+- ../spi/spi_atmel.txt
+- ../i2c/i2c-at91.txt
+
+Example:
+
+flexcom at f8034000 {
+ compatible = "atmel,sama5d2-flexcom";
+ reg = <0xf8034000 0x200>;
+ clocks = <&flx0_clk>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf8034000 0x800>;
+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
+
+ spi at f8034400 {
+ compatible = "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flx0_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&flx0_clk>;
+ clock-names = "spi_clk";
+ atmel,fifo-size = <32>;
+
+ mtd_dataflash at 0 {
+ compatible = "atmel,at25f512b";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+ };
+};
--
1.8.2.2
^ permalink raw reply related [flat|nested] 4+ messages in thread* [PATCH v5 3/3] mfd: atmel-flexcom: add a driver for Atmel Flexible Serial Communication Unit
2015-07-21 14:21 [PATCH v5 0/3] mfd: flexcom: add a driver for Flexcom Cyrille Pitchen
2015-07-21 14:21 ` [PATCH v5 1/3] mfd: atmel-flexcom: create include file with macros used by DT bindings Cyrille Pitchen
2015-07-21 14:21 ` [PATCH v5 2/3] mfd: devicetree: add bindings for Atmel Flexcom Cyrille Pitchen
@ 2015-07-21 14:21 ` Cyrille Pitchen
2 siblings, 0 replies; 4+ messages in thread
From: Cyrille Pitchen @ 2015-07-21 14:21 UTC (permalink / raw)
To: linux-arm-kernel
This driver supports the new Atmel Flexcom. The Flexcom is a wrapper which
integrates one SPI controller, one I2C controller and one USART. Only one
function can be enabled at a time. This driver selects the function once
for all, when the Flexcom is probed, according to the value of the new
"atmel,flexcom-mode" device tree property.
This driver has chosen to present the Flexcom to the system as a MFD so
the implementation is seamless for the existing Atmel SPI, I2C and USART
drivers.
Also the Flexcom embeds FIFOs: the latest patches of the SPI, I2C and
USART drivers take advantage of this new feature.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
drivers/mfd/Kconfig | 11 +++++
drivers/mfd/Makefile | 1 +
drivers/mfd/atmel-flexcom.c | 104 ++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 116 insertions(+)
create mode 100644 drivers/mfd/atmel-flexcom.c
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index d5ad04dad081..9b33ad0653d1 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -59,6 +59,17 @@ config MFD_AAT2870_CORE
additional drivers must be enabled in order to use the
functionality of the device.
+config MFD_ATMEL_FLEXCOM
+ tristate "Atmel Flexcom (Flexible Serial Communication Unit)"
+ select MFD_CORE
+ depends on OF
+ help
+ Select this to get support for Atmel Flexcom. This is a wrapper
+ which embeds a SPI controller, a I2C controller and a USART. Only
+ one function can be used at a time. The choice is done at boot time
+ by the probe function of this MFD driver according to a device tree
+ property.
+
config MFD_ATMEL_HLCDC
tristate "Atmel HLCDC (High-end LCD Controller)"
select MFD_CORE
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 0e5cfeba107c..c666bf51abf3 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -160,6 +160,7 @@ obj-$(CONFIG_MFD_SPMI_PMIC) += qcom-spmi-pmic.o
obj-$(CONFIG_TPS65911_COMPARATOR) += tps65911-comparator.o
obj-$(CONFIG_MFD_TPS65090) += tps65090.o
obj-$(CONFIG_MFD_AAT2870_CORE) += aat2870-core.o
+obj-$(CONFIG_MFD_ATMEL_FLEXCOM) += atmel-flexcom.o
obj-$(CONFIG_MFD_ATMEL_HLCDC) += atmel-hlcdc.o
obj-$(CONFIG_MFD_INTEL_MSIC) += intel_msic.o
obj-$(CONFIG_MFD_PALMAS) += palmas.o
diff --git a/drivers/mfd/atmel-flexcom.c b/drivers/mfd/atmel-flexcom.c
new file mode 100644
index 000000000000..bd9e828cdec7
--- /dev/null
+++ b/drivers/mfd/atmel-flexcom.c
@@ -0,0 +1,104 @@
+/*
+ * Driver for Atmel Flexcom
+ *
+ * Copyright (C) 2015 Atmel Corporation
+ *
+ * Author: Cyrille Pitchen <cyrille.pitchen@atmel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/clk.h>
+#include <dt-bindings/mfd/atmel-flexcom.h>
+
+/* I/O register offsets */
+#define FLEX_MR 0x0 /* Mode Register */
+#define FLEX_VERSION 0xfc /* Version Register */
+
+/* Mode Register bit fields */
+#define FLEX_MR_OPMODE_OFFSET (0) /* Operating Mode */
+#define FLEX_MR_OPMODE_MASK (0x3 << FLEX_MR_OPMODE_OFFSET)
+#define FLEX_MR_OPMODE(opmode) (((opmode) << FLEX_MR_OPMODE_OFFSET) & \
+ FLEX_MR_OPMODE_MASK)
+
+
+static int atmel_flexcom_probe(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct clk *clk;
+ struct resource *res;
+ void __iomem *base;
+ u32 opmode;
+ int err;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(base))
+ return PTR_ERR(base);
+
+ clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ err = of_property_read_u32(np, "atmel,flexcom-mode", &opmode);
+ if (err)
+ return err;
+
+ if (opmode < ATMEL_FLEXCOM_MODE_USART ||
+ opmode > ATMEL_FLEXCOM_MODE_TWI)
+ return -EINVAL;
+
+ err = clk_prepare_enable(clk);
+ if (err)
+ return err;
+
+ /*
+ * Set the Operating Mode in the Mode Register: only the selected device
+ * is clocked. Hence, registers of the other serial devices remain
+ * inaccessible and are read as zero. Also the external I/O lines of the
+ * Flexcom are muxed to reach the selected device.
+ */
+ writel(FLEX_MR_OPMODE(opmode), base + FLEX_MR);
+
+ clk_disable_unprepare(clk);
+
+ return of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev);
+}
+
+static const struct of_device_id atmel_flexcom_of_match[] = {
+ { .compatible = "atmel,sama5d2-flexcom" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, atmel_flexcom_of_match);
+
+static struct platform_driver atmel_flexcom_driver = {
+ .driver = {
+ .name = "atmel_flexcom",
+ .of_match_table = atmel_flexcom_of_match,
+ },
+ .probe = atmel_flexcom_probe,
+};
+
+module_platform_driver(atmel_flexcom_driver);
+
+MODULE_AUTHOR("Cyrille Pitchen <cyrille.pitchen@atmel.com>");
+MODULE_DESCRIPTION("Atmel Flexcom MFD driver");
+MODULE_LICENSE("GPL v2");
--
1.8.2.2
^ permalink raw reply related [flat|nested] 4+ messages in thread