[PATCH 01/35] arm64: dts: m3ulcb: enable I2C

[PATCH 01/35] arm64: dts: m3ulcb: enable I2C

[Simon Horman]

From: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>

This supports I2C2 bus on M3ULCB board

Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
index 372b2a944716..5554b555b874 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
@@ -120,6 +120,11 @@
 		function = "scif_clk";
 	};
 
+	i2c2_pins: i2c2 {
+		groups = "i2c2_a";
+		function = "i2c2";
+	};
+
 	sdhi0_pins: sd0 {
 		groups = "sdhi0_data4", "sdhi0_ctrl";
 		function = "sdhi0";
@@ -182,6 +187,13 @@
 	clock-frequency = <14745600>;
 };
 
+&i2c2 {
+	pinctrl-0 = <&i2c2_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
 &wdt0 {
 	timeout-sec = <60>;
 	status = "okay";
-- 
2.1.4

[PATCH 02/35] arm64: dts: m3ulcb: Update memory node to 2 GiB map

[Simon Horman]

From: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>

This patch updates memory region:

  - After changes, the new map of the m3ulcb board on R8A7796 SoC
    Bank0: 1GiB RAM : 0x000048000000 -> 0x0007fffffff
    Bank1: 1GiB RAM : 0x000600000000 -> 0x0063fffffff

  - Before changes, the old map looked like this:
    Bank0: 1GiB RAM : 0x000048000000 -> 0x0007fffffff

Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
index 5554b555b874..02051a3236a5 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
@@ -32,6 +32,11 @@
 		reg = <0x0 0x48000000 0x0 0x38000000>;
 	};
 
+	memory at 600000000 {
+		device_type = "memory";
+		reg = <0x6 0x00000000 0x0 0x40000000>;
+	};
+
 	leds {
 		compatible = "gpio-leds";
 
-- 
2.1.4

[PATCH 03/35] arm64: dts: m3ulcb: enable EthernetAVB

[Simon Horman]

From: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>

This supports Ethernet AVB on M3ULCB board

Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts | 32 ++++++++++++++++++++++++++
 1 file changed, 32 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
index 02051a3236a5..75974b246dd1 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
@@ -20,6 +20,7 @@
 
 	aliases {
 		serial0 = &scif2;
+		ethernet0 = &avb;
 	};
 
 	chosen {
@@ -115,6 +116,11 @@
 	pinctrl-0 = <&scif_clk_pins>;
 	pinctrl-names = "default";
 
+	avb_pins: avb {
+		groups = "avb_mdc";
+		function = "avb";
+	};
+
 	scif2_pins: scif2 {
 		groups = "scif2_data_a";
 		function = "scif2";
@@ -155,6 +161,32 @@
 	};
 };
 
+&avb {
+	pinctrl-0 = <&avb_pins>;
+	pinctrl-names = "default";
+	renesas,no-ether-link;
+	phy-handle = <&phy0>;
+	status = "okay";
+
+	phy0: ethernet-phy at 0 {
+		rxc-skew-ps = <900>;
+		rxdv-skew-ps = <0>;
+		rxd0-skew-ps = <0>;
+		rxd1-skew-ps = <0>;
+		rxd2-skew-ps = <0>;
+		rxd3-skew-ps = <0>;
+		txc-skew-ps = <900>;
+		txen-skew-ps = <0>;
+		txd0-skew-ps = <0>;
+		txd1-skew-ps = <0>;
+		txd2-skew-ps = <0>;
+		txd3-skew-ps = <0>;
+		reg = <0>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
 &sdhi0 {
 	pinctrl-0 = <&sdhi0_pins>;
 	pinctrl-1 = <&sdhi0_pins_uhs>;
-- 
2.1.4

[PATCH 04/35] arm64: dts: r8a7795: salvator-x: Update memory node to 4 GiB map

[Simon Horman]

From: Takeshi Kihara <takeshi.kihara.df@renesas.com>

This patch addes memory region:

  - After changes, the Salvator-X board has the following map:
    Bank0: 1GiB RAM : 0x000048000000 -> 0x0007fffffff
    Bank1: 1GiB RAM : 0x000500000000 -> 0x0053fffffff
    Bank2: 1GiB RAM : 0x000600000000 -> 0x0063fffffff
    Bank3: 1GiB RAM : 0x000700000000 -> 0x0073fffffff

  - Before changes, the old map looked like this:
    Bank0: 1GiB RAM : 0x000048000000 -> 0x0007fffffff

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts | 15 +++++++++++++++
 1 file changed, 15 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
index 639aa085d996..f1b6ad3def15 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
@@ -56,6 +56,21 @@
 		reg = <0x0 0x48000000 0x0 0x38000000>;
 	};
 
+	memory at 500000000 {
+		device_type = "memory";
+		reg = <0x5 0x00000000 0x0 0x40000000>;
+	};
+
+	memory at 600000000 {
+		device_type = "memory";
+		reg = <0x6 0x00000000 0x0 0x40000000>;
+	};
+
+	memory at 700000000 {
+		device_type = "memory";
+		reg = <0x7 0x00000000 0x0 0x40000000>;
+	};
+
 	x12_clk: x12 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
-- 
2.1.4

[PATCH 05/35] arm64: dts: r8a7795: salvator-x: enable HS200 for eMMC

[Simon Horman]

From: Wolfram Sang <wsa+renesas@sang-engineering.com>

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
index f1b6ad3def15..ff68bac4cd7e 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
@@ -482,6 +482,7 @@
 	vmmc-supply = <&reg_3p3v>;
 	vqmmc-supply = <&reg_1p8v>;
 	bus-width = <8>;
+	mmc-hs200-1_8v;
 	non-removable;
 	status = "okay";
 };
-- 
2.1.4

[PATCH 06/35] arm64: dts: r8a7796: salvator-x: enable HS200 for eMMC

[Simon Horman]

From: Wolfram Sang <wsa+renesas@sang-engineering.com>

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
index c9f59b6ce33f..7f0ac6a9d49b 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
@@ -216,6 +216,7 @@
 	vmmc-supply = <&reg_3p3v>;
 	vqmmc-supply = <&reg_1p8v>;
 	bus-width = <8>;
+	mmc-hs200-1_8v;
 	non-removable;
 	status = "okay";
 };
-- 
2.1.4

[PATCH 07/35] arm64: dts: m3ulcb: enable HS200 for eMMC

[Simon Horman]

From: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>

This supports HS200 mode for eMMC on M3ULCB board

Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
index 75974b246dd1..c2a4549d3738 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
@@ -209,6 +209,7 @@
 	vmmc-supply = <&reg_3p3v>;
 	vqmmc-supply = <&reg_1p8v>;
 	bus-width = <8>;
+	mmc-hs200-1_8v;
 	non-removable;
 	status = "okay";
 };
-- 
2.1.4

[PATCH 08/35] arm64: dts: h3ulcb: enable HS200 for eMMC

[Simon Horman]

From: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>

This supports HS200 mode for eMMC on H3ULCB board

Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
index ab352159de65..3574965e0747 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
@@ -328,6 +328,7 @@
 	vmmc-supply = <&reg_3p3v>;
 	vqmmc-supply = <&reg_1p8v>;
 	bus-width = <8>;
+	mmc-hs200-1_8v;
 	non-removable;
 	status = "okay";
 };
-- 
2.1.4

[PATCH 09/35] arm64: dts: m3ulcb: Fix EthernetAVB PHY timing

[Simon Horman]

Set PHY rxc-skew-ps to 1500 and all other values to their default values.

This is intended to to address failures in the case of 1Gbps communication
using the salvator-x board with the KSZ9031RNX phy. This has been
reported to occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs.

Based in a similar patch for the r8a7796 salvator-x by Kazuya Mizuguchi.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts | 13 +------------
 1 file changed, 1 insertion(+), 12 deletions(-)

diff --git a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
index c2a4549d3738..440d93e8388d 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
@@ -169,18 +169,7 @@
 	status = "okay";
 
 	phy0: ethernet-phy at 0 {
-		rxc-skew-ps = <900>;
-		rxdv-skew-ps = <0>;
-		rxd0-skew-ps = <0>;
-		rxd1-skew-ps = <0>;
-		rxd2-skew-ps = <0>;
-		rxd3-skew-ps = <0>;
-		txc-skew-ps = <900>;
-		txen-skew-ps = <0>;
-		txd0-skew-ps = <0>;
-		txd1-skew-ps = <0>;
-		txd2-skew-ps = <0>;
-		txd3-skew-ps = <0>;
+		rxc-skew-ps = <1500>;
 		reg = <0>;
 		interrupt-parent = <&gpio2>;
 		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
-- 
2.1.4

[PATCH 10/35] arm64: dts: r8a7796: salvator-x: Enable NFS root

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Cfr. commit b2407c566ba29215 ("arm64: dts: r8a7795: enable nfs root on
Salvator-X board").

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
index 7f0ac6a9d49b..18b478be484c 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
@@ -23,7 +23,7 @@
 	};
 
 	chosen {
-		bootargs = "ignore_loglevel";
+		bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
 		stdout-path = "serial0:115200n8";
 	};
 
-- 
2.1.4

[PATCH 11/35] arm64: dts: r8a7796: salvator-x: Set drive-strength for ravb pins

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

The EthernetAVB should not depend on the bootloader to setup correct
drive-strength values.  Values for drive-strength where found by
examining the registers after the bootloader has configured the
registers and successfully used the EthernetAVB.

Based on commit 7d73a4da2681dc5d ("arm64: dts: r8a7795: salvator-x: Set
drive-strength for ravb pins").

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts | 18 ++++++++++++++++--
 1 file changed, 16 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
index 18b478be484c..31f02219ed2f 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
@@ -110,8 +110,22 @@
 	pinctrl-names = "default";
 
 	avb_pins: avb {
-		groups = "avb_mdc";
-		function = "avb";
+		mux {
+			groups = "avb_link", "avb_phy_int", "avb_mdc",
+				 "avb_mii";
+			function = "avb";
+		};
+
+		pins_mdc {
+			groups = "avb_mdc";
+			drive-strength = <24>;
+		};
+
+		pins_mii_tx {
+			pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0",
+			       "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3";
+			drive-strength = <12>;
+		};
 	};
 
 	scif1_pins: scif1 {
-- 
2.1.4

[PATCH 12/35] arm64: dts: r8a7795: update PFC node name to pin-controller

[Simon Horman]

The device trees for Renesas SoCs use either pfc or pin-controller as the
node name for the PFC device. This patch is intended to take a step towards
unifying the node name used as pin-controller which appears to be the more
generic of the two and thus more in keeping with the DT specs.

My analysis is that this is a user-visible change to the extent that kernel
logs, and sysfs entries change from e6060000.pfc and pfc at e6060000 to
e6060000.pin-controller and pin-controller at e6060000.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm64/boot/dts/renesas/r8a7795.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/renesas/r8a7795.dtsi b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
index e99d6443b3e4..7d87dff70ac8 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
@@ -398,7 +398,7 @@
 			#power-domain-cells = <1>;
 		};
 
-		pfc: pfc at e6060000 {
+		pfc: pin-controller at e6060000 {
 			compatible = "renesas,pfc-r8a7795";
 			reg = <0 0xe6060000 0 0x50c>;
 		};
-- 
2.1.4

[GIT PULL] Renesas ARM64 Based SoC DT Updates for v4.13

[Simon Horman]

Hi Olof, Hi Kevin, Hi Arnd,

Please consider these Renesas ARM64 based SoC DT updates for v4.13.


The following changes since commit 2ea659a9ef488125eb46da6eb571de5eae5c43f6:

  Linux 4.12-rc1 (2017-05-13 13:19:49 -0700)

are available in the git repository at:

  https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-arm64-dt-for-v4.13

for you to fetch changes up to 0b03c32db03d63de695c1e0ab1950eb12b135fa7:

  arm64: dts: r8a7795: salvator-x: Add support for R-Car H3 ES2.0 (2017-05-22 14:54:57 +0200)

----------------------------------------------------------------
Renesas ARM64 Based SoC DT Updates for v4.13

* Add support for R-Car H3 ES2.0
* Break out common board support
* Set drive-strength for ravb pins for r8a7795/h3ulcb and r8a7796/m3ulcb
* Enable HDMI outputs on r8a7795/salvator-x
* Add R-Car audio to DT of r8a7796 SoC
* Add current sense amplifiers to DT of r8a779[56]/salvator-x
* Enable NFS-root on r8a7796/salvator-x
* Enable HS200 for eMMC on r8a779[56]/salvator-x,
  r8a7795/h3ulcb and r8a7796/m3ulcb
* Enable EthernetAVB, I2C r8a7796/m3ulcb
* Update memory node to 2 GiB map on r8a7796/m3ulcb

----------------------------------------------------------------
Geert Uytterhoeven (9):
      arm64: dts: r8a7796: salvator-x: Enable NFS root
      arm64: dts: r8a7796: salvator-x: Set drive-strength for ravb pins
      arm64: dts: r8a7796: Add external audio clocks
      arm64: dts: r8a7796: Add external PCIe bus clock
      arm64: dts: r8a7796: Add placeholders for various devices
      arm64: dts: renesas: Extract common Salvator-X board support
      arm64: dts: renesas: Extract common ULCB board support
      arm64: dts: r8a7795: Add support for R-Car H3 ES2.0
      arm64: dts: r8a7795: salvator-x: Add support for R-Car H3 ES2.0

Jacopo Mondi (1):
      arm64: dts: salvator-x: Add current sense amplifiers

Koji Matsuoka (1):
      arm64: dts: renesas: r8a7795-salvator-x: Enable HDMI outputs

Kuninori Morimoto (7):
      arm64: dts: r8a7796: add AUDIO_DMAC support
      arm64: dts: r8a7796: add Sound SSI PIO support
      arm64: dts: r8a7796: add Sound SSI DMA support
      arm64: dts: r8a7796: add Sound SRC support
      arm64: dts: r8a7796: add Sound DVC support
      arm64: dts: r8a7796: add Sound CTU support
      arm64: dts: r8a7796: add Sound MIX support

Laurent Pinchart (4):
      arm64: dts: salvator-x: Add panel backlight support
      arm64: dts: renesas: salvator-x: Add DU external dot clock sources
      arm64: dts: renesas: salvator-x: Add HDMI output connectors
      arm64: dts: renesas: r8a7795-salvator-x: Add DU external dot clocks

Simon Horman (3):
      arm64: dts: m3ulcb: Fix EthernetAVB PHY timing
      arm64: dts: r8a7795: update PFC node name to pin-controller
      arm64: dts: ulcb: Set drive-strength for ravb pins

Takeshi Kihara (2):
      arm64: dts: r8a7795: salvator-x: Update memory node to 4 GiB map
      arm64: dts: r8a7796: Add PWM device nodes

Ulrich Hecht (1):
      arm64: dts: renesas: r8a7795: Add HDMI encoder support

Vladimir Barinov (5):
      arm64: dts: m3ulcb: enable I2C
      arm64: dts: m3ulcb: Update memory node to 2 GiB map
      arm64: dts: m3ulcb: enable EthernetAVB
      arm64: dts: m3ulcb: enable HS200 for eMMC
      arm64: dts: h3ulcb: enable HS200 for eMMC

Wolfram Sang (2):
      arm64: dts: r8a7795: salvator-x: enable HS200 for eMMC
      arm64: dts: r8a7796: salvator-x: enable HS200 for eMMC

 arch/arm64/boot/dts/renesas/Makefile               |   1 +
 .../boot/dts/renesas/r8a7795-es1-salvator-x.dts    | 115 ++++
 arch/arm64/boot/dts/renesas/r8a7795-es1.dtsi       |  84 +++
 arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts     | 344 +----------
 arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts | 565 ++----------------
 arch/arm64/boot/dts/renesas/r8a7795.dtsi           | 121 ++--
 arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts     | 168 +-----
 arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts | 244 +-------
 arch/arm64/boot/dts/renesas/r8a7796.dtsi           | 409 +++++++++++++
 arch/arm64/boot/dts/renesas/salvator-x.dtsi        | 644 +++++++++++++++++++++
 arch/arm64/boot/dts/renesas/ulcb.dtsi              | 367 ++++++++++++
 11 files changed, 1734 insertions(+), 1328 deletions(-)
 create mode 100644 arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dts
 create mode 100644 arch/arm64/boot/dts/renesas/r8a7795-es1.dtsi
 create mode 100644 arch/arm64/boot/dts/renesas/salvator-x.dtsi
 create mode 100644 arch/arm64/boot/dts/renesas/ulcb.dtsi

[PATCH 13/35] arm64: dts: r8a7796: Add external audio clocks

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Add the external audio clocks as zero Hz fixed-frequency clocks.
Boards that provide these clocks should override them.

Based on commit 623197b90c7aa97c ("arm64: renesas: r8a7795: Sound SSI
PIO support").

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7796.dtsi | 23 +++++++++++++++++++++++
 1 file changed, 23 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index 2ec1ed5f4991..101cd41d693a 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -120,6 +120,29 @@
 		clock-frequency = <0>;
 	};
 
+	/*
+	 * The external audio clocks are configured as 0 Hz fixed frequency
+	 * clocks by default.
+	 * Boards that provide audio clocks should override them.
+	 */
+	audio_clk_a: audio_clk_a {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
+	audio_clk_b: audio_clk_b {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
+	audio_clk_c: audio_clk_c {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
 	/* External CAN clock - to be overridden by boards that provide it */
 	can_clk: can {
 		compatible = "fixed-clock";
-- 
2.1.4

[PATCH 14/35] arm64: dts: r8a7796: Add external PCIe bus clock

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Add the external PCIe bus clock as a zero Hz fixed-frequency clock.
Boards that provide this clock should override it.

Based on r8a7795.dtsi.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7796.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index 101cd41d693a..8e2aab8b6b10 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -157,6 +157,13 @@
 		clock-frequency = <0>;
 	};
 
+	/* External PCIe clock - can be overridden by the board */
+	pcie_bus_clk: pcie_bus {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
 	soc {
 		compatible = "simple-bus";
 		interrupt-parent = <&gic>;
-- 
2.1.4

[PATCH 15/35] arm64: dts: r8a7796: Add placeholders for various devices

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Add empty device nodes serving as placeholders for devices that are not
yet supported and/or tested on R-Car M3-W, but are supported and used on
Salvator-X or H3ULCB boards equipped with an R-Car H3 SoC.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7796.dtsi | 82 ++++++++++++++++++++++++++++++++
 1 file changed, 82 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index 8e2aab8b6b10..60a4289d0b14 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -961,6 +961,38 @@
 			dma-channels = <16>;
 		};
 
+		hsusb: usb at e6590000 {
+			/* placeholder */
+		};
+
+		xhci0: usb at ee000000 {
+			/* placeholder */
+		};
+
+		ohci0: usb at ee080000 {
+			/* placeholder */
+		};
+
+		ehci0: usb at ee080100 {
+			/* placeholder */
+		};
+
+		usb2_phy0: usb-phy at ee080200 {
+			/* placeholder */
+		};
+
+		ohci1: usb at ee0a0000 {
+			/* placeholder */
+		};
+
+		ehci1: usb at ee0a0100 {
+			/* placeholder */
+		};
+
+		usb2_phy1: usb-phy at ee0a0200 {
+			/* placeholder */
+		};
+
 		sdhi0: sd at ee100000 {
 			compatible = "renesas,sdhi-r8a7796";
 			reg = <0 0xee100000 0 0x2000>;
@@ -1063,5 +1095,55 @@
 				};
 			};
 		};
+
+		rcar_sound: sound at ec500000 {
+			/* placeholder */
+
+			rcar_sound,dvc {
+				dvc0: dvc-0 {
+				};
+
+				dvc1: dvc-1 {
+				};
+			};
+
+			rcar_sound,src {
+				src0: src-0 {
+				};
+				src1: src-1 {
+				};
+			};
+
+			rcar_sound,ssi {
+				ssi0: ssi-0 {
+				};
+
+				ssi1: ssi-1 {
+				};
+			};
+		};
+
+		pciec0: pcie at fe000000 {
+			/* placeholder */
+		};
+
+		pciec1: pcie at ee800000 {
+			/* placeholder */
+		};
+
+		du: display at feb00000 {
+			/* placeholder */
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port at 0 {
+					reg = <0>;
+					du_out_rgb: endpoint {
+					};
+				};
+			};
+		};
 	};
 };
-- 
2.1.4

[PATCH 16/35] arm64: dts: renesas: Extract common Salvator-X board support

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

The Renesas Salvator-X development board can be equipped with either an
R-Car H3 or M3-W SiP, which are pin-compatible.  Both boards use
different DTBs.

Reduce duplication by extracting common Salvator-X board support into
its own .dtsi file.  References to SoC-specific clocks are handled
through cpp definitions.  Sort device nodes while at it.

For boards with an R-Car H3 SiP, there are no functional changes.

For boards with an R-Car M3-W SiP, the following new devices are now
described in DT:
  - External audio, CAN, and PCIe clocks,
  - USB Vbus regulator,
  - CS2000 clock generator,
  - AK4613 Audio Codec,
  - VGA.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts | 543 +-------------------
 arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts | 259 +---------
 arch/arm64/boot/dts/renesas/salvator-x.dtsi        | 555 +++++++++++++++++++++
 3 files changed, 563 insertions(+), 794 deletions(-)
 create mode 100644 arch/arm64/boot/dts/renesas/salvator-x.dtsi

diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
index ff68bac4cd7e..52fce67df341 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
@@ -8,48 +8,16 @@
  * kind, whether express or implied.
  */
 
-/*
- * SSI-AK4613
- *
- * This command is required when Playback/Capture
- *
- *	amixer set "DVC Out" 100%
- *	amixer set "DVC In" 100%
- *
- * You can use Mute
- *
- *	amixer set "DVC Out Mute" on
- *	amixer set "DVC In Mute" on
- *
- * You can use Volume Ramp
- *
- *	amixer set "DVC Out Ramp Up Rate"   "0.125 dB/64 steps"
- *	amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
- *	amixer set "DVC Out Ramp" on
- *	aplay xxx.wav &
- *	amixer set "DVC Out"  80%  // Volume Down
- *	amixer set "DVC Out" 100%  // Volume Up
- */
+#define CPG_AUDIO_CLK_I		R8A7795_CLK_S0D4
 
 /dts-v1/;
 #include "r8a7795.dtsi"
-#include <dt-bindings/gpio/gpio.h>
+#include "salvator-x.dtsi"
 
 / {
 	model = "Renesas Salvator-X board based on r8a7795";
 	compatible = "renesas,salvator-x", "renesas,r8a7795";
 
-	aliases {
-		serial0 = &scif2;
-		serial1 = &scif1;
-		ethernet0 = &avb;
-	};
-
-	chosen {
-		bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory at 48000000 {
 		device_type = "memory";
 		/* first 128MB is reserved for secure area. */
@@ -70,531 +38,30 @@
 		device_type = "memory";
 		reg = <0x7 0x00000000 0x0 0x40000000>;
 	};
-
-	x12_clk: x12 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <24576000>;
-	};
-
-	reg_1p8v: regulator0 {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-1.8V";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	reg_3p3v: regulator1 {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-3.3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	vcc_sdhi0: regulator-vcc-sdhi0 {
-		compatible = "regulator-fixed";
-
-		regulator-name = "SDHI0 Vcc";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vccq_sdhi0: regulator-vccq-sdhi0 {
-		compatible = "regulator-gpio";
-
-		regulator-name = "SDHI0 VccQ";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
-		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
-	};
-
-	vcc_sdhi3: regulator-vcc-sdhi3 {
-		compatible = "regulator-fixed";
-
-		regulator-name = "SDHI3 Vcc";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vccq_sdhi3: regulator-vccq-sdhi3 {
-		compatible = "regulator-gpio";
-
-		regulator-name = "SDHI3 VccQ";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
-		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
-	};
-
-	vbus0_usb2: regulator-vbus0-usb2 {
-		compatible = "regulator-fixed";
-
-		regulator-name = "USB20_VBUS0";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-
-		gpio = <&gpio6 16 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	audio_clkout: audio_clkout {
-		/*
-		 * This is same as <&rcar_sound 0>
-		 * but needed to avoid cs2000/rcar_sound probe dead-lock
-		 */
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <11289600>;
-	};
-
-	rsnd_ak4613: sound {
-		compatible = "simple-audio-card";
-
-		simple-audio-card,format = "left_j";
-		simple-audio-card,bitclock-master = <&sndcpu>;
-		simple-audio-card,frame-master = <&sndcpu>;
-
-		sndcpu: simple-audio-card,cpu {
-			sound-dai = <&rcar_sound>;
-		};
-
-		sndcodec: simple-audio-card,codec {
-			sound-dai = <&ak4613>;
-		};
-	};
-
-	vga-encoder {
-		compatible = "adi,adv7123";
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port at 0 {
-				reg = <0>;
-				adv7123_in: endpoint {
-					remote-endpoint = <&du_out_rgb>;
-				};
-			};
-			port at 1 {
-				reg = <1>;
-				adv7123_out: endpoint {
-					remote-endpoint = <&vga_in>;
-				};
-			};
-		};
-	};
-
-	vga {
-		compatible = "vga-connector";
-
-		port {
-			vga_in: endpoint {
-				remote-endpoint = <&adv7123_out>;
-			};
-		};
-	};
 };
 
-&du {
-	pinctrl-0 = <&du_pins>;
-	pinctrl-names = "default";
+&ehci2 {
 	status = "okay";
-
-	ports {
-		port at 0 {
-			endpoint {
-				remote-endpoint = <&adv7123_in>;
-			};
-		};
-		port at 3 {
-			lvds_connector: endpoint {
-			};
-		};
-	};
-};
-
-&extal_clk {
-	clock-frequency = <16666666>;
 };
 
-&extalr_clk {
-	clock-frequency = <32768>;
+&ohci2 {
+	status = "okay";
 };
 
 &pfc {
-	pinctrl-0 = <&scif_clk_pins>;
-	pinctrl-names = "default";
-
-	scif1_pins: scif1 {
-		groups = "scif1_data_a", "scif1_ctrl";
-		function = "scif1";
-	};
-	scif2_pins: scif2 {
-		groups = "scif2_data_a";
-		function = "scif2";
-	};
-	scif_clk_pins: scif_clk {
-		groups = "scif_clk_a";
-		function = "scif_clk";
-	};
-
-	i2c2_pins: i2c2 {
-		groups = "i2c2_a";
-		function = "i2c2";
-	};
-
-	avb_pins: avb {
-		mux {
-			groups = "avb_link", "avb_phy_int", "avb_mdc",
-				 "avb_mii";
-			function = "avb";
-		};
-
-		pins_mdc {
-			groups = "avb_mdc";
-			drive-strength = <24>;
-		};
-
-		pins_mii_tx {
-			pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0",
-			       "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3";
-			drive-strength = <12>;
-		};
-	};
-
-	du_pins: du {
-		groups = "du_rgb888", "du_sync", "du_oddf", "du_clk_out_0";
-		function = "du";
-	};
-
-	sdhi0_pins: sd0 {
-		groups = "sdhi0_data4", "sdhi0_ctrl";
-		function = "sdhi0";
-		power-source = <3300>;
-	};
-
-	sdhi0_pins_uhs: sd0_uhs {
-		groups = "sdhi0_data4", "sdhi0_ctrl";
-		function = "sdhi0";
-		power-source = <1800>;
-	};
-
-	sdhi2_pins: sd2 {
-		groups = "sdhi2_data8", "sdhi2_ctrl";
-		function = "sdhi2";
-		power-source = <3300>;
-	};
-
-	sdhi2_pins_uhs: sd2_uhs {
-		groups = "sdhi2_data8", "sdhi2_ctrl";
-		function = "sdhi2";
-		power-source = <1800>;
-	};
-
-	sdhi3_pins: sd3 {
-		groups = "sdhi3_data4", "sdhi3_ctrl";
-		function = "sdhi3";
-		power-source = <3300>;
-	};
-
-	sdhi3_pins_uhs: sd3_uhs {
-		groups = "sdhi3_data4", "sdhi3_ctrl";
-		function = "sdhi3";
-		power-source = <1800>;
-	};
-
-	sound_pins: sound {
-		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
-		function = "ssi";
-	};
-
-	sound_clk_pins: sound_clk {
-		groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a",
-			 "audio_clkout_a", "audio_clkout3_a";
-		function = "audio_clk";
-	};
-
-	usb0_pins: usb0 {
-		groups = "usb0";
-		function = "usb0";
-	};
-
-	usb1_pins: usb1 {
-		mux {
-			groups = "usb1";
-			function = "usb1";
-		};
-
-		ovc {
-			pins = "GP_6_27";
-			bias-pull-up;
-		};
-
-		pwen {
-			pins = "GP_6_26";
-			bias-pull-down;
-		};
-	};
-
 	usb2_pins: usb2 {
 		groups = "usb2";
 		function = "usb2";
 	};
 };
 
-&scif1 {
-	pinctrl-0 = <&scif1_pins>;
-	pinctrl-names = "default";
-
-	uart-has-rtscts;
-	status = "okay";
-};
-
-&scif2 {
-	pinctrl-0 = <&scif2_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&scif_clk {
-	clock-frequency = <14745600>;
-};
-
-&i2c2 {
-	pinctrl-0 = <&i2c2_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-
-	clock-frequency = <100000>;
-
-	ak4613: codec at 10 {
-		compatible = "asahi-kasei,ak4613";
-		#sound-dai-cells = <0>;
-		reg = <0x10>;
-		clocks = <&rcar_sound 3>;
-
-		asahi-kasei,in1-single-end;
-		asahi-kasei,in2-single-end;
-		asahi-kasei,out1-single-end;
-		asahi-kasei,out2-single-end;
-		asahi-kasei,out3-single-end;
-		asahi-kasei,out4-single-end;
-		asahi-kasei,out5-single-end;
-		asahi-kasei,out6-single-end;
-	};
-
-	cs2000: clk_multiplier at 4f {
-		#clock-cells = <0>;
-		compatible = "cirrus,cs2000-cp";
-		reg = <0x4f>;
-		clocks = <&audio_clkout>, <&x12_clk>;
-		clock-names = "clk_in", "ref_clk";
-
-		assigned-clocks = <&cs2000>;
-		assigned-clock-rates = <24576000>; /* 1/1 divide */
-	};
-};
-
-&rcar_sound {
-	pinctrl-0 = <&sound_pins &sound_clk_pins>;
-	pinctrl-names = "default";
-
-	/* Single DAI */
-	#sound-dai-cells = <0>;
-
-	/* audio_clkout0/1/2/3 */
-	#clock-cells = <1>;
-	clock-frequency = <11289600>;
-
-	status = "okay";
-
-	/* update <audio_clk_b> to <cs2000> */
-	clocks = <&cpg CPG_MOD 1005>,
-		 <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
-		 <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
-		 <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
-		 <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
-		 <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
-		 <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
-		 <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
-		 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
-		 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
-		 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
-		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
-		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
-		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
-		 <&audio_clk_a>, <&cs2000>,
-		 <&audio_clk_c>,
-		 <&cpg CPG_CORE R8A7795_CLK_S0D4>;
-
-	rcar_sound,dai {
-		dai0 {
-			playback = <&ssi0 &src0 &dvc0>;
-			capture  = <&ssi1 &src1 &dvc1>;
-		};
-	};
-};
-
 &sata {
 	status = "okay";
 };
 
-&sdhi0 {
-	pinctrl-0 = <&sdhi0_pins>;
-	pinctrl-1 = <&sdhi0_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&vcc_sdhi0>;
-	vqmmc-supply = <&vccq_sdhi0>;
-	cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
-	bus-width = <4>;
-	sd-uhs-sdr50;
-	status = "okay";
-};
-
-&sdhi2 {
-	/* used for on-board 8bit eMMC */
-	pinctrl-0 = <&sdhi2_pins>;
-	pinctrl-1 = <&sdhi2_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&reg_3p3v>;
-	vqmmc-supply = <&reg_1p8v>;
-	bus-width = <8>;
-	mmc-hs200-1_8v;
-	non-removable;
-	status = "okay";
-};
-
-&sdhi3 {
-	pinctrl-0 = <&sdhi3_pins>;
-	pinctrl-1 = <&sdhi3_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&vcc_sdhi3>;
-	vqmmc-supply = <&vccq_sdhi3>;
-	cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
-	bus-width = <4>;
-	sd-uhs-sdr50;
-	status = "okay";
-};
-
-&ssi1 {
-	shared-pin;
-};
-
-&wdt0 {
-	timeout-sec = <60>;
-	status = "okay";
-};
-
-&audio_clk_a {
-	clock-frequency = <22579200>;
-};
-
-&i2c_dvfs {
-	status = "okay";
-};
-
-&avb {
-	pinctrl-0 = <&avb_pins>;
-	pinctrl-names = "default";
-	renesas,no-ether-link;
-	phy-handle = <&phy0>;
-	status = "okay";
-
-	phy0: ethernet-phy at 0 {
-		rxc-skew-ps = <1500>;
-		reg = <0>;
-		interrupt-parent = <&gpio2>;
-		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
-	};
-};
-
-&xhci0 {
-	status = "okay";
-};
-
-&usb2_phy0 {
-	pinctrl-0 = <&usb0_pins>;
-	pinctrl-names = "default";
-
-	vbus-supply = <&vbus0_usb2>;
-	status = "okay";
-};
-
-&usb2_phy1 {
-	pinctrl-0 = <&usb1_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
 &usb2_phy2 {
 	pinctrl-0 = <&usb2_pins>;
 	pinctrl-names = "default";
 
 	status = "okay";
 };
-
-&ehci0 {
-	status = "okay";
-};
-
-&ehci1 {
-	status = "okay";
-};
-
-&ehci2 {
-	status = "okay";
-};
-
-&ohci0 {
-	status = "okay";
-};
-
-&ohci1 {
-	status = "okay";
-};
-
-&ohci2 {
-	status = "okay";
-};
-
-&hsusb {
-	status = "okay";
-};
-
-&pcie_bus_clk {
-	clock-frequency = <100000000>;
-};
-
-&pciec0 {
-	status = "okay";
-};
-
-&pciec1 {
-	status = "okay";
-};
diff --git a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
index 31f02219ed2f..db4f162d6bdd 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
@@ -8,25 +8,16 @@
  * kind, whether express or implied.
  */
 
+#define CPG_AUDIO_CLK_I		R8A7796_CLK_S0D4
+
 /dts-v1/;
 #include "r8a7796.dtsi"
-#include <dt-bindings/gpio/gpio.h>
+#include "salvator-x.dtsi"
 
 / {
 	model = "Renesas Salvator-X board based on r8a7796";
 	compatible = "renesas,salvator-x", "renesas,r8a7796";
 
-	aliases {
-		serial0 = &scif2;
-		serial1 = &scif1;
-		ethernet0 = &avb;
-	};
-
-	chosen {
-		bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory at 48000000 {
 		device_type = "memory";
 		/* first 128MB is reserved for secure area. */
@@ -37,248 +28,4 @@
 		device_type = "memory";
 		reg = <0x6 0x00000000 0x0 0x80000000>;
 	};
-
-	reg_1p8v: regulator0 {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-1.8V";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	reg_3p3v: regulator1 {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-3.3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	vcc_sdhi0: regulator-vcc-sdhi0 {
-		compatible = "regulator-fixed";
-
-		regulator-name = "SDHI0 Vcc";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vccq_sdhi0: regulator-vccq-sdhi0 {
-		compatible = "regulator-gpio";
-
-		regulator-name = "SDHI0 VccQ";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
-		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
-	};
-
-	vcc_sdhi3: regulator-vcc-sdhi3 {
-		compatible = "regulator-fixed";
-
-		regulator-name = "SDHI3 Vcc";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vccq_sdhi3: regulator-vccq-sdhi3 {
-		compatible = "regulator-gpio";
-
-		regulator-name = "SDHI3 VccQ";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
-		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
-	};
-};
-
-&pfc {
-	pinctrl-0 = <&scif_clk_pins>;
-	pinctrl-names = "default";
-
-	avb_pins: avb {
-		mux {
-			groups = "avb_link", "avb_phy_int", "avb_mdc",
-				 "avb_mii";
-			function = "avb";
-		};
-
-		pins_mdc {
-			groups = "avb_mdc";
-			drive-strength = <24>;
-		};
-
-		pins_mii_tx {
-			pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0",
-			       "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3";
-			drive-strength = <12>;
-		};
-	};
-
-	scif1_pins: scif1 {
-		groups = "scif1_data_a", "scif1_ctrl";
-		function = "scif1";
-	};
-
-	scif2_pins: scif2 {
-		groups = "scif2_data_a";
-		function = "scif2";
-	};
-	scif_clk_pins: scif_clk {
-		groups = "scif_clk_a";
-		function = "scif_clk";
-	};
-
-	i2c2_pins: i2c2 {
-		groups = "i2c2_a";
-		function = "i2c2";
-	};
-
-	sdhi0_pins: sd0 {
-		groups = "sdhi0_data4", "sdhi0_ctrl";
-		function = "sdhi0";
-		power-source = <3300>;
-	};
-
-	sdhi0_pins_uhs: sd0_uhs {
-		groups = "sdhi0_data4", "sdhi0_ctrl";
-		function = "sdhi0";
-		power-source = <1800>;
-	};
-
-	sdhi2_pins: sd2 {
-		groups = "sdhi2_data8", "sdhi2_ctrl";
-		function = "sdhi2";
-		power-source = <3300>;
-	};
-
-	sdhi2_pins_uhs: sd2_uhs {
-		groups = "sdhi2_data8", "sdhi2_ctrl";
-		function = "sdhi2";
-		power-source = <1800>;
-	};
-
-	sdhi3_pins: sd3 {
-		groups = "sdhi3_data4", "sdhi3_ctrl";
-		function = "sdhi3";
-		power-source = <3300>;
-	};
-
-	sdhi3_pins_uhs: sd3_uhs {
-		groups = "sdhi3_data4", "sdhi3_ctrl";
-		function = "sdhi3";
-		power-source = <1800>;
-	};
-};
-
-&avb {
-	pinctrl-0 = <&avb_pins>;
-	pinctrl-names = "default";
-	renesas,no-ether-link;
-	phy-handle = <&phy0>;
-	status = "okay";
-
-	phy0: ethernet-phy at 0 {
-		rxc-skew-ps = <1500>;
-		reg = <0>;
-		interrupt-parent = <&gpio2>;
-		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
-	};
-};
-
-&extal_clk {
-	clock-frequency = <16666666>;
-};
-
-&extalr_clk {
-	clock-frequency = <32768>;
-};
-
-&sdhi0 {
-	pinctrl-0 = <&sdhi0_pins>;
-	pinctrl-1 = <&sdhi0_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&vcc_sdhi0>;
-	vqmmc-supply = <&vccq_sdhi0>;
-	cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
-	bus-width = <4>;
-	sd-uhs-sdr50;
-	status = "okay";
-};
-
-&sdhi2 {
-	/* used for on-board 8bit eMMC */
-	pinctrl-0 = <&sdhi2_pins>;
-	pinctrl-1 = <&sdhi2_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&reg_3p3v>;
-	vqmmc-supply = <&reg_1p8v>;
-	bus-width = <8>;
-	mmc-hs200-1_8v;
-	non-removable;
-	status = "okay";
-};
-
-&sdhi3 {
-	pinctrl-0 = <&sdhi3_pins>;
-	pinctrl-1 = <&sdhi3_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&vcc_sdhi3>;
-	vqmmc-supply = <&vccq_sdhi3>;
-	cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
-	bus-width = <4>;
-	sd-uhs-sdr50;
-	status = "okay";
-};
-
-&scif1 {
-	pinctrl-0 = <&scif1_pins>;
-	pinctrl-names = "default";
-
-	uart-has-rtscts;
-	status = "okay";
-};
-
-&scif2 {
-	pinctrl-0 = <&scif2_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&scif_clk {
-	clock-frequency = <14745600>;
-};
-
-&i2c2 {
-	pinctrl-0 = <&i2c2_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&wdt0 {
-	timeout-sec = <60>;
-	status = "okay";
-};
-
-&i2c_dvfs {
-	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/renesas/salvator-x.dtsi b/arch/arm64/boot/dts/renesas/salvator-x.dtsi
new file mode 100644
index 000000000000..47a482f20c9d
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/salvator-x.dtsi
@@ -0,0 +1,555 @@
+/*
+ * Device Tree Source for the Salvator-X board
+ *
+ * Copyright (C) 2015-2016 Renesas Electronics Corp.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/*
+ * SSI-AK4613
+ *
+ * This command is required when Playback/Capture
+ *
+ *	amixer set "DVC Out" 100%
+ *	amixer set "DVC In" 100%
+ *
+ * You can use Mute
+ *
+ *	amixer set "DVC Out Mute" on
+ *	amixer set "DVC In Mute" on
+ *
+ * You can use Volume Ramp
+ *
+ *	amixer set "DVC Out Ramp Up Rate"   "0.125 dB/64 steps"
+ *	amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
+ *	amixer set "DVC Out Ramp" on
+ *	aplay xxx.wav &
+ *	amixer set "DVC Out"  80%  // Volume Down
+ *	amixer set "DVC Out" 100%  // Volume Up
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Renesas Salvator-X board";
+	compatible = "renesas,salvator-x";
+
+	aliases {
+		serial0 = &scif2;
+		serial1 = &scif1;
+		ethernet0 = &avb;
+	};
+
+	chosen {
+		bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
+		stdout-path = "serial0:115200n8";
+	};
+
+	audio_clkout: audio_clkout {
+		/*
+		 * This is same as <&rcar_sound 0>
+		 * but needed to avoid cs2000/rcar_sound probe dead-lock
+		 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <11289600>;
+	};
+
+	reg_1p8v: regulator0 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator1 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	rsnd_ak4613: sound {
+		compatible = "simple-audio-card";
+
+		simple-audio-card,format = "left_j";
+		simple-audio-card,bitclock-master = <&sndcpu>;
+		simple-audio-card,frame-master = <&sndcpu>;
+
+		sndcpu: simple-audio-card,cpu {
+			sound-dai = <&rcar_sound>;
+		};
+
+		sndcodec: simple-audio-card,codec {
+			sound-dai = <&ak4613>;
+		};
+	};
+
+	vbus0_usb2: regulator-vbus0-usb2 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "USB20_VBUS0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&gpio6 16 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vcc_sdhi0: regulator-vcc-sdhi0 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "SDHI0 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vccq_sdhi0: regulator-vccq-sdhi0 {
+		compatible = "regulator-gpio";
+
+		regulator-name = "SDHI0 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1
+			  1800000 0>;
+	};
+
+	vcc_sdhi3: regulator-vcc-sdhi3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "SDHI3 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vccq_sdhi3: regulator-vccq-sdhi3 {
+		compatible = "regulator-gpio";
+
+		regulator-name = "SDHI3 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1
+			  1800000 0>;
+	};
+
+	vga {
+		compatible = "vga-connector";
+
+		port {
+			vga_in: endpoint {
+				remote-endpoint = <&adv7123_out>;
+			};
+		};
+	};
+
+	vga-encoder {
+		compatible = "adi,adv7123";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port at 0 {
+				reg = <0>;
+				adv7123_in: endpoint {
+					remote-endpoint = <&du_out_rgb>;
+				};
+			};
+			port at 1 {
+				reg = <1>;
+				adv7123_out: endpoint {
+					remote-endpoint = <&vga_in>;
+				};
+			};
+		};
+	};
+
+	x12_clk: x12 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24576000>;
+	};
+};
+
+&audio_clk_a {
+	clock-frequency = <22579200>;
+};
+
+&avb {
+	pinctrl-0 = <&avb_pins>;
+	pinctrl-names = "default";
+	renesas,no-ether-link;
+	phy-handle = <&phy0>;
+	status = "okay";
+
+	phy0: ethernet-phy at 0 {
+		rxc-skew-ps = <1500>;
+		reg = <0>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&du {
+	pinctrl-0 = <&du_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	ports {
+		port at 0 {
+			endpoint {
+				remote-endpoint = <&adv7123_in>;
+			};
+		};
+		port at 3 {
+			lvds_connector: endpoint {
+			};
+		};
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&extal_clk {
+	clock-frequency = <16666666>;
+};
+
+&extalr_clk {
+	clock-frequency = <32768>;
+};
+
+&hsusb {
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-0 = <&i2c2_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+
+	clock-frequency = <100000>;
+
+	ak4613: codec at 10 {
+		compatible = "asahi-kasei,ak4613";
+		#sound-dai-cells = <0>;
+		reg = <0x10>;
+		clocks = <&rcar_sound 3>;
+
+		asahi-kasei,in1-single-end;
+		asahi-kasei,in2-single-end;
+		asahi-kasei,out1-single-end;
+		asahi-kasei,out2-single-end;
+		asahi-kasei,out3-single-end;
+		asahi-kasei,out4-single-end;
+		asahi-kasei,out5-single-end;
+		asahi-kasei,out6-single-end;
+	};
+
+	cs2000: clk_multiplier at 4f {
+		#clock-cells = <0>;
+		compatible = "cirrus,cs2000-cp";
+		reg = <0x4f>;
+		clocks = <&audio_clkout>, <&x12_clk>;
+		clock-names = "clk_in", "ref_clk";
+
+		assigned-clocks = <&cs2000>;
+		assigned-clock-rates = <24576000>; /* 1/1 divide */
+	};
+};
+
+&i2c_dvfs {
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&pcie_bus_clk {
+	clock-frequency = <100000000>;
+};
+
+&pciec0 {
+	status = "okay";
+};
+
+&pciec1 {
+	status = "okay";
+};
+
+&pfc {
+	pinctrl-0 = <&scif_clk_pins>;
+	pinctrl-names = "default";
+
+	avb_pins: avb {
+		mux {
+			groups = "avb_link", "avb_phy_int", "avb_mdc",
+				 "avb_mii";
+			function = "avb";
+		};
+
+		pins_mdc {
+			groups = "avb_mdc";
+			drive-strength = <24>;
+		};
+
+		pins_mii_tx {
+			pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0",
+			       "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3";
+			drive-strength = <12>;
+		};
+	};
+
+	du_pins: du {
+		groups = "du_rgb888", "du_sync", "du_oddf", "du_clk_out_0";
+		function = "du";
+	};
+
+	i2c2_pins: i2c2 {
+		groups = "i2c2_a";
+		function = "i2c2";
+	};
+
+	scif1_pins: scif1 {
+		groups = "scif1_data_a", "scif1_ctrl";
+		function = "scif1";
+	};
+
+	scif2_pins: scif2 {
+		groups = "scif2_data_a";
+		function = "scif2";
+	};
+
+	scif_clk_pins: scif_clk {
+		groups = "scif_clk_a";
+		function = "scif_clk";
+	};
+
+	sdhi0_pins: sd0 {
+		groups = "sdhi0_data4", "sdhi0_ctrl";
+		function = "sdhi0";
+		power-source = <3300>;
+	};
+
+	sdhi0_pins_uhs: sd0_uhs {
+		groups = "sdhi0_data4", "sdhi0_ctrl";
+		function = "sdhi0";
+		power-source = <1800>;
+	};
+
+	sdhi2_pins: sd2 {
+		groups = "sdhi2_data8", "sdhi2_ctrl";
+		function = "sdhi2";
+		power-source = <3300>;
+	};
+
+	sdhi2_pins_uhs: sd2_uhs {
+		groups = "sdhi2_data8", "sdhi2_ctrl";
+		function = "sdhi2";
+		power-source = <1800>;
+	};
+
+	sdhi3_pins: sd3 {
+		groups = "sdhi3_data4", "sdhi3_ctrl";
+		function = "sdhi3";
+		power-source = <3300>;
+	};
+
+	sdhi3_pins_uhs: sd3_uhs {
+		groups = "sdhi3_data4", "sdhi3_ctrl";
+		function = "sdhi3";
+		power-source = <1800>;
+	};
+
+	sound_pins: sound {
+		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
+		function = "ssi";
+	};
+
+	sound_clk_pins: sound_clk {
+		groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a",
+			 "audio_clkout_a", "audio_clkout3_a";
+		function = "audio_clk";
+	};
+
+	usb0_pins: usb0 {
+		groups = "usb0";
+		function = "usb0";
+	};
+
+	usb1_pins: usb1 {
+		mux {
+			groups = "usb1";
+			function = "usb1";
+		};
+
+		ovc {
+			pins = "GP_6_27";
+			bias-pull-up;
+		};
+
+		pwen {
+			pins = "GP_6_26";
+			bias-pull-down;
+		};
+	};
+};
+
+&rcar_sound {
+	pinctrl-0 = <&sound_pins &sound_clk_pins>;
+	pinctrl-names = "default";
+
+	/* Single DAI */
+	#sound-dai-cells = <0>;
+
+	/* audio_clkout0/1/2/3 */
+	#clock-cells = <1>;
+	clock-frequency = <11289600>;
+
+	status = "okay";
+
+	/* update <audio_clk_b> to <cs2000> */
+	clocks = <&cpg CPG_MOD 1005>,
+		 <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
+		 <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
+		 <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
+		 <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
+		 <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
+		 <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
+		 <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
+		 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
+		 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
+		 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
+		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
+		 <&audio_clk_a>, <&cs2000>,
+		 <&audio_clk_c>,
+		 <&cpg CPG_CORE CPG_AUDIO_CLK_I>;
+
+	rcar_sound,dai {
+		dai0 {
+			playback = <&ssi0 &src0 &dvc0>;
+			capture  = <&ssi1 &src1 &dvc1>;
+		};
+	};
+};
+
+&scif1 {
+	pinctrl-0 = <&scif1_pins>;
+	pinctrl-names = "default";
+
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&scif2 {
+	pinctrl-0 = <&scif2_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&scif_clk {
+	clock-frequency = <14745600>;
+};
+
+&sdhi0 {
+	pinctrl-0 = <&sdhi0_pins>;
+	pinctrl-1 = <&sdhi0_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&vcc_sdhi0>;
+	vqmmc-supply = <&vccq_sdhi0>;
+	cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
+	bus-width = <4>;
+	sd-uhs-sdr50;
+	status = "okay";
+};
+
+&sdhi2 {
+	/* used for on-board 8bit eMMC */
+	pinctrl-0 = <&sdhi2_pins>;
+	pinctrl-1 = <&sdhi2_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	non-removable;
+	status = "okay";
+};
+
+&sdhi3 {
+	pinctrl-0 = <&sdhi3_pins>;
+	pinctrl-1 = <&sdhi3_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&vcc_sdhi3>;
+	vqmmc-supply = <&vccq_sdhi3>;
+	cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
+	bus-width = <4>;
+	sd-uhs-sdr50;
+	status = "okay";
+};
+
+&ssi1 {
+	shared-pin;
+};
+
+&usb2_phy0 {
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+
+	vbus-supply = <&vbus0_usb2>;
+	status = "okay";
+};
+
+&usb2_phy1 {
+	pinctrl-0 = <&usb1_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&wdt0 {
+	timeout-sec = <60>;
+	status = "okay";
+};
+
+&xhci0 {
+	status = "okay";
+};
-- 
2.1.4

[PATCH 17/35] arm64: dts: renesas: Extract common ULCB board support

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

The Renesas ULCB development board can be equipped with either an R-Car
H3 or M3-W SiP, which are pin-compatible.  Both boards use different
DTBs.

Reduce duplication by extracting common ULCB board support into its own
.dtsi file.  References to SoC-specific clocks are handled through cpp
definitions.  Sort device nodes while at it.

For H3ULCB, there are no functional changes.

For M3ULCB, the following new devices are now described in DT:
  - External audio, CAN, and PCIe clocks,
  - CS2000 clock generator,
  - AK4613 Audio Codec.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts | 341 +-----------------------
 arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts | 201 +-------------
 arch/arm64/boot/dts/renesas/ulcb.dtsi          | 353 +++++++++++++++++++++++++
 3 files changed, 359 insertions(+), 536 deletions(-)
 create mode 100644 arch/arm64/boot/dts/renesas/ulcb.dtsi

diff --git a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
index 3574965e0747..a1fbf0ab8ad8 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
@@ -9,24 +9,16 @@
  * kind, whether express or implied.
  */
 
+#define CPG_AUDIO_CLK_I		R8A7795_CLK_S0D4
+
 /dts-v1/;
 #include "r8a7795.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
+#include "ulcb.dtsi"
 
 / {
 	model = "Renesas H3ULCB board based on r8a7795";
 	compatible = "renesas,h3ulcb", "renesas,r8a7795";
 
-	aliases {
-		serial0 = &scif2;
-		ethernet0 = &avb;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory at 48000000 {
 		device_type = "memory";
 		/* first 128MB is reserved for secure area. */
@@ -47,331 +39,4 @@
 		device_type = "memory";
 		reg = <0x7 0x00000000 0x0 0x40000000>;
 	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		led5 {
-			gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
-		};
-		led6 {
-			gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>;
-		};
-	};
-
-	keyboard {
-		compatible = "gpio-keys";
-
-		key-1 {
-			linux,code = <KEY_1>;
-			label = "SW3";
-			wakeup-source;
-			debounce-interval = <20>;
-			gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	x12_clk: x12 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <24576000>;
-	};
-
-	reg_1p8v: regulator0 {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-1.8V";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	reg_3p3v: regulator1 {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-3.3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	vcc_sdhi0: regulator-vcc-sdhi0 {
-		compatible = "regulator-fixed";
-
-		regulator-name = "SDHI0 Vcc";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vccq_sdhi0: regulator-vccq-sdhi0 {
-		compatible = "regulator-gpio";
-
-		regulator-name = "SDHI0 VccQ";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
-		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
-	};
-
-	audio_clkout: audio-clkout {
-		/*
-		 * This is same as <&rcar_sound 0>
-		 * but needed to avoid cs2000/rcar_sound probe dead-lock
-		 */
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <11289600>;
-	};
-
-	rsnd_ak4613: sound {
-		compatible = "simple-audio-card";
-
-		simple-audio-card,format = "left_j";
-		simple-audio-card,bitclock-master = <&sndcpu>;
-		simple-audio-card,frame-master = <&sndcpu>;
-
-		sndcpu: simple-audio-card,cpu {
-			sound-dai = <&rcar_sound>;
-		};
-
-		sndcodec: simple-audio-card,codec {
-			sound-dai = <&ak4613>;
-		};
-	};
-};
-
-&extal_clk {
-	clock-frequency = <16666666>;
-};
-
-&extalr_clk {
-	clock-frequency = <32768>;
-};
-
-&pfc {
-	pinctrl-0 = <&scif_clk_pins>;
-	pinctrl-names = "default";
-
-	scif2_pins: scif2 {
-		groups = "scif2_data_a";
-		function = "scif2";
-	};
-
-	scif_clk_pins: scif_clk {
-		groups = "scif_clk_a";
-		function = "scif_clk";
-	};
-
-	i2c2_pins: i2c2 {
-		groups = "i2c2_a";
-		function = "i2c2";
-	};
-
-	avb_pins: avb {
-		groups = "avb_mdc";
-		function = "avb";
-	};
-
-	sdhi0_pins: sd0 {
-		groups = "sdhi0_data4", "sdhi0_ctrl";
-		function = "sdhi0";
-		power-source = <3300>;
-	};
-
-	sdhi0_pins_uhs: sd0_uhs {
-		groups = "sdhi0_data4", "sdhi0_ctrl";
-		function = "sdhi0";
-		power-source = <1800>;
-	};
-
-	sdhi2_pins: sd2 {
-		groups = "sdhi2_data8", "sdhi2_ctrl";
-		function = "sdhi2";
-		power-source = <3300>;
-	};
-
-	sdhi2_pins_uhs: sd2_uhs {
-		groups = "sdhi2_data8", "sdhi2_ctrl";
-		function = "sdhi2";
-		power-source = <1800>;
-	};
-
-	sound_pins: sound {
-		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
-		function = "ssi";
-	};
-
-	sound_clk_pins: sound-clk {
-		groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a",
-			 "audio_clkout_a", "audio_clkout3_a";
-		function = "audio_clk";
-	};
-
-	usb1_pins: usb1 {
-		groups = "usb1";
-		function = "usb1";
-	};
-};
-
-&scif2 {
-	pinctrl-0 = <&scif2_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&scif_clk {
-	clock-frequency = <14745600>;
-};
-
-&i2c2 {
-	pinctrl-0 = <&i2c2_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-
-	clock-frequency = <100000>;
-
-	ak4613: codec at 10 {
-		compatible = "asahi-kasei,ak4613";
-		#sound-dai-cells = <0>;
-		reg = <0x10>;
-		clocks = <&rcar_sound 3>;
-
-		asahi-kasei,in1-single-end;
-		asahi-kasei,in2-single-end;
-		asahi-kasei,out1-single-end;
-		asahi-kasei,out2-single-end;
-		asahi-kasei,out3-single-end;
-		asahi-kasei,out4-single-end;
-		asahi-kasei,out5-single-end;
-		asahi-kasei,out6-single-end;
-	};
-
-	cs2000: clk-multiplier at 4f {
-		#clock-cells = <0>;
-		compatible = "cirrus,cs2000-cp";
-		reg = <0x4f>;
-		clocks = <&audio_clkout>, <&x12_clk>;
-		clock-names = "clk_in", "ref_clk";
-
-		assigned-clocks = <&cs2000>;
-		assigned-clock-rates = <24576000>; /* 1/1 divide */
-	};
-};
-
-&rcar_sound {
-	pinctrl-0 = <&sound_pins &sound_clk_pins>;
-	pinctrl-names = "default";
-
-	/* Single DAI */
-	#sound-dai-cells = <0>;
-
-	/* audio_clkout0/1/2/3 */
-	#clock-cells = <1>;
-	clock-frequency = <11289600>;
-
-	status = "okay";
-
-	/* update <audio_clk_b> to <cs2000> */
-	clocks = <&cpg CPG_MOD 1005>,
-		 <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
-		 <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
-		 <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
-		 <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
-		 <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
-		 <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
-		 <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
-		 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
-		 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
-		 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
-		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
-		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
-		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
-		 <&audio_clk_a>, <&cs2000>,
-		 <&audio_clk_c>,
-		 <&cpg CPG_CORE R8A7795_CLK_S0D4>;
-
-	rcar_sound,dai {
-		dai0 {
-			playback = <&ssi0 &src0 &dvc0>;
-			capture  = <&ssi1 &src1 &dvc1>;
-		};
-	};
-};
-
-&sdhi0 {
-	pinctrl-0 = <&sdhi0_pins>;
-	pinctrl-1 = <&sdhi0_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&vcc_sdhi0>;
-	vqmmc-supply = <&vccq_sdhi0>;
-	cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
-	bus-width = <4>;
-	sd-uhs-sdr50;
-	status = "okay";
-};
-
-&sdhi2 {
-	/* used for on-board 8bit eMMC */
-	pinctrl-0 = <&sdhi2_pins>;
-	pinctrl-1 = <&sdhi2_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&reg_3p3v>;
-	vqmmc-supply = <&reg_1p8v>;
-	bus-width = <8>;
-	mmc-hs200-1_8v;
-	non-removable;
-	status = "okay";
-};
-
-&ssi1 {
-	shared-pin;
-};
-
-&wdt0 {
-	timeout-sec = <60>;
-	status = "okay";
-};
-
-&audio_clk_a {
-	clock-frequency = <22579200>;
-};
-
-&avb {
-	pinctrl-0 = <&avb_pins>;
-	pinctrl-names = "default";
-	renesas,no-ether-link;
-	phy-handle = <&phy0>;
-	status = "okay";
-
-	phy0: ethernet-phy at 0 {
-		rxc-skew-ps = <1500>;
-		reg = <0>;
-		interrupt-parent = <&gpio2>;
-		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
-	};
-};
-
-&usb2_phy1 {
-	pinctrl-0 = <&usb1_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&ehci1 {
-	status = "okay";
-};
-
-&ohci1 {
-	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
index 440d93e8388d..38b58b7fca4b 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
@@ -9,24 +9,16 @@
  * kind, whether express or implied.
  */
 
+#define CPG_AUDIO_CLK_I		R8A7796_CLK_S0D4
+
 /dts-v1/;
 #include "r8a7796.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
+#include "ulcb.dtsi"
 
 / {
 	model = "Renesas M3ULCB board based on r8a7796";
 	compatible = "renesas,m3ulcb", "renesas,r8a7796";
 
-	aliases {
-		serial0 = &scif2;
-		ethernet0 = &avb;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory at 48000000 {
 		device_type = "memory";
 		/* first 128MB is reserved for secure area. */
@@ -37,191 +29,4 @@
 		device_type = "memory";
 		reg = <0x6 0x00000000 0x0 0x40000000>;
 	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		led5 {
-			gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
-		};
-		led6 {
-			gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>;
-		};
-	};
-
-	keyboard {
-		compatible = "gpio-keys";
-
-		key-1 {
-			linux,code = <KEY_1>;
-			label = "SW3";
-			wakeup-source;
-			debounce-interval = <20>;
-			gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	reg_1p8v: regulator0 {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-1.8V";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	reg_3p3v: regulator1 {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-3.3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	vcc_sdhi0: regulator-vcc-sdhi0 {
-		compatible = "regulator-fixed";
-
-		regulator-name = "SDHI0 Vcc";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vccq_sdhi0: regulator-vccq-sdhi0 {
-		compatible = "regulator-gpio";
-
-		regulator-name = "SDHI0 VccQ";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
-		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
-	};
-};
-
-&extal_clk {
-	clock-frequency = <16666666>;
-};
-
-&extalr_clk {
-	clock-frequency = <32768>;
-};
-
-&pfc {
-	pinctrl-0 = <&scif_clk_pins>;
-	pinctrl-names = "default";
-
-	avb_pins: avb {
-		groups = "avb_mdc";
-		function = "avb";
-	};
-
-	scif2_pins: scif2 {
-		groups = "scif2_data_a";
-		function = "scif2";
-	};
-
-	scif_clk_pins: scif_clk {
-		groups = "scif_clk_a";
-		function = "scif_clk";
-	};
-
-	i2c2_pins: i2c2 {
-		groups = "i2c2_a";
-		function = "i2c2";
-	};
-
-	sdhi0_pins: sd0 {
-		groups = "sdhi0_data4", "sdhi0_ctrl";
-		function = "sdhi0";
-		power-source = <3300>;
-	};
-
-	sdhi0_pins_uhs: sd0_uhs {
-		groups = "sdhi0_data4", "sdhi0_ctrl";
-		function = "sdhi0";
-		power-source = <1800>;
-	};
-
-	sdhi2_pins: sd2 {
-		groups = "sdhi2_data8", "sdhi2_ctrl";
-		function = "sdhi2";
-		power-source = <3300>;
-	};
-
-	sdhi2_pins_uhs: sd2_uhs {
-		groups = "sdhi2_data8", "sdhi2_ctrl";
-		function = "sdhi2";
-		power-source = <1800>;
-	};
-};
-
-&avb {
-	pinctrl-0 = <&avb_pins>;
-	pinctrl-names = "default";
-	renesas,no-ether-link;
-	phy-handle = <&phy0>;
-	status = "okay";
-
-	phy0: ethernet-phy at 0 {
-		rxc-skew-ps = <1500>;
-		reg = <0>;
-		interrupt-parent = <&gpio2>;
-		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
-	};
-};
-
-&sdhi0 {
-	pinctrl-0 = <&sdhi0_pins>;
-	pinctrl-1 = <&sdhi0_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&vcc_sdhi0>;
-	vqmmc-supply = <&vccq_sdhi0>;
-	cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
-	bus-width = <4>;
-	sd-uhs-sdr50;
-	status = "okay";
-};
-
-&sdhi2 {
-	/* used for on-board 8bit eMMC */
-	pinctrl-0 = <&sdhi2_pins>;
-	pinctrl-1 = <&sdhi2_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&reg_3p3v>;
-	vqmmc-supply = <&reg_1p8v>;
-	bus-width = <8>;
-	mmc-hs200-1_8v;
-	non-removable;
-	status = "okay";
-};
-
-&scif2 {
-	pinctrl-0 = <&scif2_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&scif_clk {
-	clock-frequency = <14745600>;
-};
-
-&i2c2 {
-	pinctrl-0 = <&i2c2_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&wdt0 {
-	timeout-sec = <60>;
-	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/renesas/ulcb.dtsi b/arch/arm64/boot/dts/renesas/ulcb.dtsi
new file mode 100644
index 000000000000..2bc7ceb2efa4
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/ulcb.dtsi
@@ -0,0 +1,353 @@
+/*
+ * Device Tree Source for the R-Car Gen3 ULCB board
+ *
+ * Copyright (C) 2016 Renesas Electronics Corp.
+ * Copyright (C) 2016 Cogent Embedded, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Renesas R-Car Gen3 ULCB board";
+
+	aliases {
+		serial0 = &scif2;
+		ethernet0 = &avb;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	audio_clkout: audio-clkout {
+		/*
+		 * This is same as <&rcar_sound 0>
+		 * but needed to avoid cs2000/rcar_sound probe dead-lock
+		 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <11289600>;
+	};
+
+	keyboard {
+		compatible = "gpio-keys";
+
+		key-1 {
+			linux,code = <KEY_1>;
+			label = "SW3";
+			wakeup-source;
+			debounce-interval = <20>;
+			gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led5 {
+			gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
+		};
+		led6 {
+			gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	reg_1p8v: regulator0 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator1 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	rsnd_ak4613: sound {
+		compatible = "simple-audio-card";
+
+		simple-audio-card,format = "left_j";
+		simple-audio-card,bitclock-master = <&sndcpu>;
+		simple-audio-card,frame-master = <&sndcpu>;
+
+		sndcpu: simple-audio-card,cpu {
+			sound-dai = <&rcar_sound>;
+		};
+
+		sndcodec: simple-audio-card,codec {
+			sound-dai = <&ak4613>;
+		};
+	};
+
+	vcc_sdhi0: regulator-vcc-sdhi0 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "SDHI0 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vccq_sdhi0: regulator-vccq-sdhi0 {
+		compatible = "regulator-gpio";
+
+		regulator-name = "SDHI0 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1
+			  1800000 0>;
+	};
+
+	x12_clk: x12 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24576000>;
+	};
+};
+
+&audio_clk_a {
+	clock-frequency = <22579200>;
+};
+
+&avb {
+	pinctrl-0 = <&avb_pins>;
+	pinctrl-names = "default";
+	renesas,no-ether-link;
+	phy-handle = <&phy0>;
+	status = "okay";
+
+	phy0: ethernet-phy at 0 {
+		rxc-skew-ps = <1500>;
+		reg = <0>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&extal_clk {
+	clock-frequency = <16666666>;
+};
+
+&extalr_clk {
+	clock-frequency = <32768>;
+};
+
+&i2c2 {
+	pinctrl-0 = <&i2c2_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+
+	clock-frequency = <100000>;
+
+	ak4613: codec at 10 {
+		compatible = "asahi-kasei,ak4613";
+		#sound-dai-cells = <0>;
+		reg = <0x10>;
+		clocks = <&rcar_sound 3>;
+
+		asahi-kasei,in1-single-end;
+		asahi-kasei,in2-single-end;
+		asahi-kasei,out1-single-end;
+		asahi-kasei,out2-single-end;
+		asahi-kasei,out3-single-end;
+		asahi-kasei,out4-single-end;
+		asahi-kasei,out5-single-end;
+		asahi-kasei,out6-single-end;
+	};
+
+	cs2000: clk-multiplier at 4f {
+		#clock-cells = <0>;
+		compatible = "cirrus,cs2000-cp";
+		reg = <0x4f>;
+		clocks = <&audio_clkout>, <&x12_clk>;
+		clock-names = "clk_in", "ref_clk";
+
+		assigned-clocks = <&cs2000>;
+		assigned-clock-rates = <24576000>; /* 1/1 divide */
+	};
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&pfc {
+	pinctrl-0 = <&scif_clk_pins>;
+	pinctrl-names = "default";
+
+	avb_pins: avb {
+		groups = "avb_mdc";
+		function = "avb";
+	};
+
+	i2c2_pins: i2c2 {
+		groups = "i2c2_a";
+		function = "i2c2";
+	};
+
+	scif2_pins: scif2 {
+		groups = "scif2_data_a";
+		function = "scif2";
+	};
+
+	scif_clk_pins: scif_clk {
+		groups = "scif_clk_a";
+		function = "scif_clk";
+	};
+
+	sdhi0_pins: sd0 {
+		groups = "sdhi0_data4", "sdhi0_ctrl";
+		function = "sdhi0";
+		power-source = <3300>;
+	};
+
+	sdhi0_pins_uhs: sd0_uhs {
+		groups = "sdhi0_data4", "sdhi0_ctrl";
+		function = "sdhi0";
+		power-source = <1800>;
+	};
+
+	sdhi2_pins: sd2 {
+		groups = "sdhi2_data8", "sdhi2_ctrl";
+		function = "sdhi2";
+		power-source = <3300>;
+	};
+
+	sdhi2_pins_uhs: sd2_uhs {
+		groups = "sdhi2_data8", "sdhi2_ctrl";
+		function = "sdhi2";
+		power-source = <1800>;
+	};
+
+	sound_pins: sound {
+		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
+		function = "ssi";
+	};
+
+	sound_clk_pins: sound-clk {
+		groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a",
+			 "audio_clkout_a", "audio_clkout3_a";
+		function = "audio_clk";
+	};
+
+	usb1_pins: usb1 {
+		groups = "usb1";
+		function = "usb1";
+	};
+};
+
+&rcar_sound {
+	pinctrl-0 = <&sound_pins &sound_clk_pins>;
+	pinctrl-names = "default";
+
+	/* Single DAI */
+	#sound-dai-cells = <0>;
+
+	/* audio_clkout0/1/2/3 */
+	#clock-cells = <1>;
+	clock-frequency = <11289600>;
+
+	status = "okay";
+
+	/* update <audio_clk_b> to <cs2000> */
+	clocks = <&cpg CPG_MOD 1005>,
+		 <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
+		 <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
+		 <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
+		 <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
+		 <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
+		 <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
+		 <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
+		 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
+		 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
+		 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
+		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
+		 <&audio_clk_a>, <&cs2000>,
+		 <&audio_clk_c>,
+		 <&cpg CPG_CORE CPG_AUDIO_CLK_I>;
+
+	rcar_sound,dai {
+		dai0 {
+			playback = <&ssi0 &src0 &dvc0>;
+			capture  = <&ssi1 &src1 &dvc1>;
+		};
+	};
+};
+
+&scif2 {
+	pinctrl-0 = <&scif2_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&scif_clk {
+	clock-frequency = <14745600>;
+};
+
+&sdhi0 {
+	pinctrl-0 = <&sdhi0_pins>;
+	pinctrl-1 = <&sdhi0_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&vcc_sdhi0>;
+	vqmmc-supply = <&vccq_sdhi0>;
+	cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	sd-uhs-sdr50;
+	status = "okay";
+};
+
+&sdhi2 {
+	/* used for on-board 8bit eMMC */
+	pinctrl-0 = <&sdhi2_pins>;
+	pinctrl-1 = <&sdhi2_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	non-removable;
+	status = "okay";
+};
+
+&ssi1 {
+	shared-pin;
+};
+
+&usb2_phy1 {
+	pinctrl-0 = <&usb1_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&wdt0 {
+	timeout-sec = <60>;
+	status = "okay";
+};
-- 
2.1.4

[PATCH 18/35] arm64: dts: salvator-x: Add current sense amplifiers

[Simon Horman]

From: Jacopo Mondi <jacopo+renesas@jmondi.org>

Add device nodes for two Maxim max961x current sense amplifiers
sensing VDD_08 and DVFS_08 lines.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
[geert: r8a7796-salvator-x.dts => salvator-x.dtsi]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/salvator-x.dtsi | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/salvator-x.dtsi b/arch/arm64/boot/dts/renesas/salvator-x.dtsi
index 47a482f20c9d..d5eb022d247c 100644
--- a/arch/arm64/boot/dts/renesas/salvator-x.dtsi
+++ b/arch/arm64/boot/dts/renesas/salvator-x.dtsi
@@ -283,6 +283,24 @@
 	};
 };
 
+&i2c4 {
+	status = "okay";
+
+	csa_vdd: adc at 7c {
+		compatible = "maxim,max9611";
+		reg = <0x7c>;
+
+		shunt-resistor-micro-ohms = <5000>;
+	};
+
+	csa_dvfs: adc at 7f {
+		compatible = "maxim,max9611";
+		reg = <0x7f>;
+
+		shunt-resistor-micro-ohms = <5000>;
+	};
+};
+
 &i2c_dvfs {
 	status = "okay";
 };
-- 
2.1.4

[PATCH 19/35] arm64: dts: r8a7796: add AUDIO_DMAC support

[Simon Horman]

From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7796.dtsi | 68 ++++++++++++++++++++++++++++++++
 1 file changed, 68 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index 60a4289d0b14..0a76a1c53082 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -961,6 +961,74 @@
 			dma-channels = <16>;
 		};
 
+		audma0: dma-controller at ec700000 {
+			compatible = "renesas,dmac-r8a7796",
+				     "renesas,rcar-dmac";
+			reg = <0 0xec700000 0 0x10000>;
+			interrupts = <GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					"ch0", "ch1", "ch2", "ch3",
+					"ch4", "ch5", "ch6", "ch7",
+					"ch8", "ch9", "ch10", "ch11",
+					"ch12", "ch13", "ch14", "ch15";
+			clocks = <&cpg CPG_MOD 502>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			resets = <&cpg 502>;
+			#dma-cells = <1>;
+			dma-channels = <16>;
+		};
+
+		audma1: dma-controller at ec720000 {
+			compatible = "renesas,dmac-r8a7796",
+				     "renesas,rcar-dmac";
+			reg = <0 0xec720000 0 0x10000>;
+			interrupts = <GIC_SPI 351 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 348 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 349 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 382 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 383 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					"ch0", "ch1", "ch2", "ch3",
+					"ch4", "ch5", "ch6", "ch7",
+					"ch8", "ch9", "ch10", "ch11",
+					"ch12", "ch13", "ch14", "ch15";
+			clocks = <&cpg CPG_MOD 501>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			resets = <&cpg 501>;
+			#dma-cells = <1>;
+			dma-channels = <16>;
+		};
+
 		hsusb: usb at e6590000 {
 			/* placeholder */
 		};
-- 
2.1.4

[PATCH 20/35] arm64: dts: r8a7796: add Sound SSI PIO support

[Simon Horman]

From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7796.dtsi | 64 +++++++++++++++++++++++++++++++-
 1 file changed, 62 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index 0a76a1c53082..5c6e54a1e27a 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -1165,7 +1165,42 @@
 		};
 
 		rcar_sound: sound at ec500000 {
-			/* placeholder */
+			/*
+			 * #sound-dai-cells is required
+			 *
+			 * Single DAI : #sound-dai-cells = <0>;	<&rcar_sound>;
+			 * Multi  DAI : #sound-dai-cells = <1>;	<&rcar_sound N>;
+			 */
+			/*
+			 * #clock-cells is required for audio_clkout0/1/2/3
+			 *
+			 * clkout	: #clock-cells = <0>;	<&rcar_sound>;
+			 * clkout0/1/2/3: #clock-cells = <1>;	<&rcar_sound N>;
+			 */
+			compatible =  "renesas,rcar_sound-r8a7796", "renesas,rcar_sound-gen3";
+			reg =	<0 0xec500000 0 0x1000>, /* SCU */
+				<0 0xec5a0000 0 0x100>,  /* ADG */
+				<0 0xec540000 0 0x1000>, /* SSIU */
+				<0 0xec541000 0 0x280>,  /* SSI */
+				<0 0xec740000 0 0x200>;  /* Audio DMAC peri peri*/
+			reg-names = "scu", "adg", "ssiu", "ssi", "audmapp";
+
+			clocks = <&cpg CPG_MOD 1005>,
+				 <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
+				 <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
+				 <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
+				 <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
+				 <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
+				 <&audio_clk_a>, <&audio_clk_b>,
+				 <&audio_clk_c>,
+				 <&cpg CPG_CORE R8A7796_CLK_S0D4>;
+			clock-names = "ssi-all",
+				      "ssi.9", "ssi.8", "ssi.7", "ssi.6",
+				      "ssi.5", "ssi.4", "ssi.3", "ssi.2",
+				      "ssi.1", "ssi.0",
+				      "clk_a", "clk_b", "clk_c", "clk_i";
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			status = "disabled";
 
 			rcar_sound,dvc {
 				dvc0: dvc-0 {
@@ -1184,9 +1219,34 @@
 
 			rcar_sound,ssi {
 				ssi0: ssi-0 {
+					interrupts = <GIC_SPI 370 IRQ_TYPE_LEVEL_HIGH>;
 				};
-
 				ssi1: ssi-1 {
+					interrupts = <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>;
+				};
+				ssi2: ssi-2 {
+					interrupts = <GIC_SPI 372 IRQ_TYPE_LEVEL_HIGH>;
+				};
+				ssi3: ssi-3 {
+					interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
+				};
+				ssi4: ssi-4 {
+					interrupts = <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>;
+				};
+				ssi5: ssi-5 {
+					interrupts = <GIC_SPI 375 IRQ_TYPE_LEVEL_HIGH>;
+				};
+				ssi6: ssi-6 {
+					interrupts = <GIC_SPI 376 IRQ_TYPE_LEVEL_HIGH>;
+				};
+				ssi7: ssi-7 {
+					interrupts = <GIC_SPI 377 IRQ_TYPE_LEVEL_HIGH>;
+				};
+				ssi8: ssi-8 {
+					interrupts = <GIC_SPI 378 IRQ_TYPE_LEVEL_HIGH>;
+				};
+				ssi9: ssi-9 {
+					interrupts = <GIC_SPI 379 IRQ_TYPE_LEVEL_HIGH>;
 				};
 			};
 		};
-- 
2.1.4

[PATCH 21/35] arm64: dts: r8a7796: add Sound SSI DMA support

[Simon Horman]

From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7796.dtsi | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index 5c6e54a1e27a..a1d08c89ceed 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -1220,33 +1220,53 @@
 			rcar_sound,ssi {
 				ssi0: ssi-0 {
 					interrupts = <GIC_SPI 370 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x01>, <&audma1 0x02>, <&audma0 0x15>, <&audma1 0x16>;
+					dma-names = "rx", "tx", "rxu", "txu";
 				};
 				ssi1: ssi-1 {
 					interrupts = <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x03>, <&audma1 0x04>, <&audma0 0x49>, <&audma1 0x4a>;
+					dma-names = "rx", "tx", "rxu", "txu";
 				};
 				ssi2: ssi-2 {
 					interrupts = <GIC_SPI 372 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x05>, <&audma1 0x06>, <&audma0 0x63>, <&audma1 0x64>;
+					dma-names = "rx", "tx", "rxu", "txu";
 				};
 				ssi3: ssi-3 {
 					interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x07>, <&audma1 0x08>, <&audma0 0x6f>, <&audma1 0x70>;
+					dma-names = "rx", "tx", "rxu", "txu";
 				};
 				ssi4: ssi-4 {
 					interrupts = <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x09>, <&audma1 0x0a>, <&audma0 0x71>, <&audma1 0x72>;
+					dma-names = "rx", "tx", "rxu", "txu";
 				};
 				ssi5: ssi-5 {
 					interrupts = <GIC_SPI 375 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x0b>, <&audma1 0x0c>, <&audma0 0x73>, <&audma1 0x74>;
+					dma-names = "rx", "tx", "rxu", "txu";
 				};
 				ssi6: ssi-6 {
 					interrupts = <GIC_SPI 376 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x0d>, <&audma1 0x0e>, <&audma0 0x75>, <&audma1 0x76>;
+					dma-names = "rx", "tx", "rxu", "txu";
 				};
 				ssi7: ssi-7 {
 					interrupts = <GIC_SPI 377 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x0f>, <&audma1 0x10>, <&audma0 0x79>, <&audma1 0x7a>;
+					dma-names = "rx", "tx", "rxu", "txu";
 				};
 				ssi8: ssi-8 {
 					interrupts = <GIC_SPI 378 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x11>, <&audma1 0x12>, <&audma0 0x7b>, <&audma1 0x7c>;
+					dma-names = "rx", "tx", "rxu", "txu";
 				};
 				ssi9: ssi-9 {
 					interrupts = <GIC_SPI 379 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x13>, <&audma1 0x14>, <&audma0 0x7d>, <&audma1 0x7e>;
+					dma-names = "rx", "tx", "rxu", "txu";
 				};
 			};
 		};
-- 
2.1.4

[PATCH 22/35] arm64: dts: r8a7796: add Sound SRC support

[Simon Horman]

From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7796.dtsi | 54 ++++++++++++++++++++++++++++++++
 1 file changed, 54 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index a1d08c89ceed..778275a980d3 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -1191,6 +1191,11 @@
 				 <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
 				 <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
 				 <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
+				 <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
+				 <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
+				 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
+				 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
+				 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
 				 <&audio_clk_a>, <&audio_clk_b>,
 				 <&audio_clk_c>,
 				 <&cpg CPG_CORE R8A7796_CLK_S0D4>;
@@ -1198,6 +1203,9 @@
 				      "ssi.9", "ssi.8", "ssi.7", "ssi.6",
 				      "ssi.5", "ssi.4", "ssi.3", "ssi.2",
 				      "ssi.1", "ssi.0",
+				      "src.9", "src.8", "src.7", "src.6",
+				      "src.5", "src.4", "src.3", "src.2",
+				      "src.1", "src.0",
 				      "clk_a", "clk_b", "clk_c", "clk_i";
 			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
 			status = "disabled";
@@ -1212,8 +1220,54 @@
 
 			rcar_sound,src {
 				src0: src-0 {
+					interrupts = <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x85>, <&audma1 0x9a>;
+					dma-names = "rx", "tx";
 				};
 				src1: src-1 {
+					interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x87>, <&audma1 0x9c>;
+					dma-names = "rx", "tx";
+				};
+				src2: src-2 {
+					interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x89>, <&audma1 0x9e>;
+					dma-names = "rx", "tx";
+				};
+				src3: src-3 {
+					interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x8b>, <&audma1 0xa0>;
+					dma-names = "rx", "tx";
+				};
+				src4: src-4 {
+					interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x8d>, <&audma1 0xb0>;
+					dma-names = "rx", "tx";
+				};
+				src5: src-5 {
+					interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x8f>, <&audma1 0xb2>;
+					dma-names = "rx", "tx";
+				};
+				src6: src-6 {
+					interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x91>, <&audma1 0xb4>;
+					dma-names = "rx", "tx";
+				};
+				src7: src-7 {
+					interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x93>, <&audma1 0xb6>;
+					dma-names = "rx", "tx";
+				};
+				src8: src-8 {
+					interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x95>, <&audma1 0xb8>;
+					dma-names = "rx", "tx";
+				};
+				src9: src-9 {
+					interrupts = <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&audma0 0x97>, <&audma1 0xba>;
+					dma-names = "rx", "tx";
 				};
 			};
 
-- 
2.1.4

[PATCH 23/35] arm64: dts: r8a7796: add Sound DVC support

[Simon Horman]

From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7796.dtsi | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index 778275a980d3..156c0f8a81ba 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -1196,6 +1196,7 @@
 				 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
 				 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
 				 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
+				 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
 				 <&audio_clk_a>, <&audio_clk_b>,
 				 <&audio_clk_c>,
 				 <&cpg CPG_CORE R8A7796_CLK_S0D4>;
@@ -1206,15 +1207,19 @@
 				      "src.9", "src.8", "src.7", "src.6",
 				      "src.5", "src.4", "src.3", "src.2",
 				      "src.1", "src.0",
+				      "dvc.0", "dvc.1",
 				      "clk_a", "clk_b", "clk_c", "clk_i";
 			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
 			status = "disabled";
 
 			rcar_sound,dvc {
 				dvc0: dvc-0 {
+					dmas = <&audma1 0xbc>;
+					dma-names = "tx";
 				};
-
 				dvc1: dvc-1 {
+					dmas = <&audma1 0xbe>;
+					dma-names = "tx";
 				};
 			};
 
-- 
2.1.4

[PATCH 24/35] arm64: dts: r8a7796: add Sound CTU support

[Simon Horman]

From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7796.dtsi | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index 156c0f8a81ba..7b74da1d1568 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -1196,6 +1196,7 @@
 				 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
 				 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
 				 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
+				 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
 				 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
 				 <&audio_clk_a>, <&audio_clk_b>,
 				 <&audio_clk_c>,
@@ -1207,6 +1208,7 @@
 				      "src.9", "src.8", "src.7", "src.6",
 				      "src.5", "src.4", "src.3", "src.2",
 				      "src.1", "src.0",
+				      "ctu.1", "ctu.0",
 				      "dvc.0", "dvc.1",
 				      "clk_a", "clk_b", "clk_c", "clk_i";
 			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
@@ -1223,6 +1225,17 @@
 				};
 			};
 
+			rcar_sound,ctu {
+				ctu00: ctu-0 { };
+				ctu01: ctu-1 { };
+				ctu02: ctu-2 { };
+				ctu03: ctu-3 { };
+				ctu10: ctu-4 { };
+				ctu11: ctu-5 { };
+				ctu12: ctu-6 { };
+				ctu13: ctu-7 { };
+			};
+
 			rcar_sound,src {
 				src0: src-0 {
 					interrupts = <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>;
-- 
2.1.4

[PATCH 25/35] arm64: dts: r8a7796: add Sound MIX support

[Simon Horman]

From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7796.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index 7b74da1d1568..8651fc93304d 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -1197,6 +1197,7 @@
 				 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
 				 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
 				 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+				 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
 				 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
 				 <&audio_clk_a>, <&audio_clk_b>,
 				 <&audio_clk_c>,
@@ -1208,6 +1209,7 @@
 				      "src.9", "src.8", "src.7", "src.6",
 				      "src.5", "src.4", "src.3", "src.2",
 				      "src.1", "src.0",
+				      "mix.1", "mix.0",
 				      "ctu.1", "ctu.0",
 				      "dvc.0", "dvc.1",
 				      "clk_a", "clk_b", "clk_c", "clk_i";
@@ -1225,6 +1227,11 @@
 				};
 			};
 
+			rcar_sound,mix {
+				mix0: mix-0 { };
+				mix1: mix-1 { };
+			};
+
 			rcar_sound,ctu {
 				ctu00: ctu-0 { };
 				ctu01: ctu-1 { };
-- 
2.1.4

[PATCH 26/35] arm64: dts: r8a7796: Add PWM device nodes

[Simon Horman]

From: Takeshi Kihara <takeshi.kihara.df@renesas.com>

This patch adds PWM{0,1,2,3,4,5,6} device nodes for R8A7796 SoC.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[uli: added resets, shortened reg lengths to 8]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7796.dtsi | 70 ++++++++++++++++++++++++++++++++
 1 file changed, 70 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index 8651fc93304d..b418a66f4cec 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -395,6 +395,76 @@
 			status = "disabled";
 		};
 
+		pwm0: pwm at e6e30000 {
+			compatible = "renesas,pwm-r8a7796", "renesas,pwm-rcar";
+			reg = <0 0xe6e30000 0 8>;
+			#pwm-cells = <2>;
+			clocks = <&cpg CPG_MOD 523>;
+			resets = <&cpg 523>;
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			status = "disabled";
+		};
+
+		pwm1: pwm at e6e31000 {
+			compatible = "renesas,pwm-r8a7796", "renesas,pwm-rcar";
+			reg = <0 0xe6e31000 0 8>;
+			#pwm-cells = <2>;
+			clocks = <&cpg CPG_MOD 523>;
+			resets = <&cpg 523>;
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			status = "disabled";
+		};
+
+		pwm2: pwm at e6e32000 {
+			compatible = "renesas,pwm-r8a7796", "renesas,pwm-rcar";
+			reg = <0 0xe6e32000 0 8>;
+			#pwm-cells = <2>;
+			clocks = <&cpg CPG_MOD 523>;
+			resets = <&cpg 523>;
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			status = "disabled";
+		};
+
+		pwm3: pwm at e6e33000 {
+			compatible = "renesas,pwm-r8a7796", "renesas,pwm-rcar";
+			reg = <0 0xe6e33000 0 8>;
+			#pwm-cells = <2>;
+			clocks = <&cpg CPG_MOD 523>;
+			resets = <&cpg 523>;
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			status = "disabled";
+		};
+
+		pwm4: pwm at e6e34000 {
+			compatible = "renesas,pwm-r8a7796", "renesas,pwm-rcar";
+			reg = <0 0xe6e34000 0 8>;
+			#pwm-cells = <2>;
+			clocks = <&cpg CPG_MOD 523>;
+			resets = <&cpg 523>;
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			status = "disabled";
+		};
+
+		pwm5: pwm at e6e35000 {
+			compatible = "renesas,pwm-r8a7796", "renesas,pwm-rcar";
+			reg = <0 0xe6e35000 0 8>;
+			#pwm-cells = <2>;
+			clocks = <&cpg CPG_MOD 523>;
+			resets = <&cpg 523>;
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			status = "disabled";
+		};
+
+		pwm6: pwm at e6e36000 {
+			compatible = "renesas,pwm-r8a7796", "renesas,pwm-rcar";
+			reg = <0 0xe6e36000 0 8>;
+			#pwm-cells = <2>;
+			clocks = <&cpg CPG_MOD 523>;
+			resets = <&cpg 523>;
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			status = "disabled";
+		};
+
 		i2c0: i2c at e6500000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-- 
2.1.4

[PATCH 27/35] arm64: dts: salvator-x: Add panel backlight support

[Simon Horman]

From: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

The panel backlight is controlled through a GPIO and a PWM channel.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[simon: apply to salvator-x.dtsi instead of r8a7795-salvator-x.dts]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/salvator-x.dtsi | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/salvator-x.dtsi b/arch/arm64/boot/dts/renesas/salvator-x.dtsi
index d5eb022d247c..7240bcd75918 100644
--- a/arch/arm64/boot/dts/renesas/salvator-x.dtsi
+++ b/arch/arm64/boot/dts/renesas/salvator-x.dtsi
@@ -58,6 +58,16 @@
 		clock-frequency = <11289600>;
 	};
 
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 50000>;
+
+		brightness-levels = <256 128 64 16 8 4 0>;
+		default-brightness-level = <6>;
+
+		enable-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+	};
+
 	reg_1p8v: regulator0 {
 		compatible = "regulator-fixed";
 		regulator-name = "fixed-1.8V";
@@ -358,6 +368,11 @@
 		function = "i2c2";
 	};
 
+	pwm1_pins: pwm {
+		groups = "pwm1_a";
+		function = "pwm1";
+	};
+
 	scif1_pins: scif1 {
 		groups = "scif1_data_a", "scif1_ctrl";
 		function = "scif1";
@@ -443,6 +458,13 @@
 	};
 };
 
+&pwm1 {
+	pinctrl-0 = <&pwm1_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
 &rcar_sound {
 	pinctrl-0 = <&sound_pins &sound_clk_pins>;
 	pinctrl-names = "default";
-- 
2.1.4

[PATCH 28/35] arm64: dts: renesas: r8a7795: Add HDMI encoder support

[Simon Horman]

From: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>

Add DT nodes for the two HDMI encoders in disabled state.

Based on work by Koji Matsuoka.

Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7795.dtsi | 52 ++++++++++++++++++++++++++++++++
 1 file changed, 52 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/r8a7795.dtsi b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
index 7d87dff70ac8..ee0129634cdf 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
@@ -1758,6 +1758,56 @@
 			renesas,fcp = <&fcpf2>;
 		};
 
+		hdmi0: hdmi0 at fead0000 {
+			compatible = "renesas,r8a7795-hdmi", "renesas,rcar-gen3-hdmi";
+			reg = <0 0xfead0000 0 0x10000>;
+			interrupts = <GIC_SPI 389 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 729>, <&cpg CPG_CORE R8A7795_CLK_HDMI>;
+			clock-names = "iahb", "isfr";
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			resets = <&cpg 729>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port at 0 {
+					reg = <0>;
+					dw_hdmi0_in: endpoint {
+						remote-endpoint = <&du_out_hdmi0>;
+					};
+				};
+				port at 1 {
+					reg = <1>;
+				};
+			};
+		};
+
+		hdmi1: hdmi1 at feae0000 {
+			compatible = "renesas,r8a7795-hdmi", "renesas,rcar-gen3-hdmi";
+			reg = <0 0xfeae0000 0 0x10000>;
+			interrupts = <GIC_SPI 436 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 728>, <&cpg CPG_CORE R8A7795_CLK_HDMI>;
+			clock-names = "iahb", "isfr";
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			resets = <&cpg 728>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port at 0 {
+					reg = <0>;
+					dw_hdmi1_in: endpoint {
+						remote-endpoint = <&du_out_hdmi1>;
+					};
+				};
+				port at 1 {
+					reg = <1>;
+				};
+			};
+		};
+
 		du: display at feb00000 {
 			compatible = "renesas,du-r8a7795";
 			reg = <0 0xfeb00000 0 0x80000>,
@@ -1789,11 +1839,13 @@
 				port at 1 {
 					reg = <1>;
 					du_out_hdmi0: endpoint {
+						remote-endpoint = <&dw_hdmi0_in>;
 					};
 				};
 				port at 2 {
 					reg = <2>;
 					du_out_hdmi1: endpoint {
+						remote-endpoint = <&dw_hdmi1_in>;
 					};
 				};
 				port at 3 {
-- 
2.1.4

[PATCH 29/35] arm64: dts: renesas: salvator-x: Add DU external dot clock sources

[Simon Horman]

From: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

The DU1 and DU2 external dot clocks are fixed frequency clock generators
running at 33MHz, while the DU0 and DU3 external dot clocks are
generated by an I2C-controlled programmable clock generator.

All those clock generators are available on both the H3 and M3-W
Salvator-X boards. Add them to the salvator-x.dtsi file.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/salvator-x.dtsi | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/salvator-x.dtsi b/arch/arm64/boot/dts/renesas/salvator-x.dtsi
index 7240bcd75918..35cd7e367234 100644
--- a/arch/arm64/boot/dts/renesas/salvator-x.dtsi
+++ b/arch/arm64/boot/dts/renesas/salvator-x.dtsi
@@ -198,6 +198,25 @@
 		#clock-cells = <0>;
 		clock-frequency = <24576000>;
 	};
+
+	/* External DU dot clocks */
+	x21_clk: x21-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <33000000>;
+	};
+
+	x22_clk: x22-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <33000000>;
+	};
+
+	x23_clk: x23-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
 };
 
 &audio_clk_a {
@@ -296,6 +315,14 @@
 &i2c4 {
 	status = "okay";
 
+	versaclock5: clock-generator at 6a {
+		compatible = "idt,5p49v5923";
+		reg = <0x6a>;
+		#clock-cells = <1>;
+		clocks = <&x23_clk>;
+		clock-names = "xin";
+	};
+
 	csa_vdd: adc at 7c {
 		compatible = "maxim,max9611";
 		reg = <0x7c>;
-- 
2.1.4

[PATCH 30/35] arm64: dts: renesas: salvator-x: Add HDMI output connectors

[Simon Horman]

From: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

The Salvator-X board has two HDMI output connectors. Add them to the
common salvator-x.dtsi.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/salvator-x.dtsi | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/salvator-x.dtsi b/arch/arm64/boot/dts/renesas/salvator-x.dtsi
index 35cd7e367234..5f0d4bdcd3b4 100644
--- a/arch/arm64/boot/dts/renesas/salvator-x.dtsi
+++ b/arch/arm64/boot/dts/renesas/salvator-x.dtsi
@@ -161,6 +161,28 @@
 			  1800000 0>;
 	};
 
+	hdmi0-out {
+		compatible = "hdmi-connector";
+		label = "HDMI0 OUT";
+		type = "a";
+
+		port {
+			hdmi0_con: endpoint {
+			};
+		};
+	};
+
+	hdmi1-out {
+		compatible = "hdmi-connector";
+		label = "HDMI1 OUT";
+		type = "a";
+
+		port {
+			hdmi1_con: endpoint {
+			};
+		};
+	};
+
 	vga {
 		compatible = "vga-connector";
 
-- 
2.1.4

[PATCH 31/35] arm64: dts: renesas: r8a7795-salvator-x: Add DU external dot clocks

[Simon Horman]

From: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

The DU1 and DU2 external dot clocks are provided by the fixed frequency
clock generators X21 and X22, while the DU0 and DU3 clocks are provided
by the programmable Versaclock5 clock generator.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
index 52fce67df341..2a5358b8f229 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
@@ -40,6 +40,20 @@
 	};
 };
 
+&du {
+	clocks = <&cpg CPG_MOD 724>,
+		 <&cpg CPG_MOD 723>,
+		 <&cpg CPG_MOD 722>,
+		 <&cpg CPG_MOD 721>,
+		 <&cpg CPG_MOD 727>,
+		 <&versaclock5 1>,
+		 <&x21_clk>,
+		 <&x22_clk>,
+		 <&versaclock5 2>;
+	clock-names = "du.0", "du.1", "du.2", "du.3", "lvds.0",
+		      "dclkin.0", "dclkin.1", "dclkin.2", "dclkin.3";
+};
+
 &ehci2 {
 	status = "okay";
 };
-- 
2.1.4

[PATCH 32/35] arm64: dts: renesas: r8a7795-salvator-x: Enable HDMI outputs

[Simon Horman]

From: Koji Matsuoka <koji.matsuoka.xm@renesas.com>

Enable the HDMI encoders for the H3 Salvator-X board. The number of
encoders varies between the H3 and M3-W SoCs, so they can't be enabled
in the common salvator-x.dtsi file.

Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts | 34 ++++++++++++++++++++++
 1 file changed, 34 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
index 2a5358b8f229..fcd9ca73f2c7 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
@@ -58,6 +58,40 @@
 	status = "okay";
 };
 
+&hdmi0 {
+	status = "okay";
+
+	ports {
+		port at 1 {
+			reg = <1>;
+			rcar_dw_hdmi0_out: endpoint {
+				remote-endpoint = <&hdmi0_con>;
+			};
+		};
+	};
+};
+
+&hdmi0_con {
+	remote-endpoint = <&rcar_dw_hdmi0_out>;
+};
+
+&hdmi1 {
+	status = "okay";
+
+	ports {
+		port at 1 {
+			reg = <1>;
+			rcar_dw_hdmi1_out: endpoint {
+				remote-endpoint = <&hdmi1_con>;
+			};
+		};
+	};
+};
+
+&hdmi1_con {
+	remote-endpoint = <&rcar_dw_hdmi1_out>;
+};
+
 &ohci2 {
 	status = "okay";
 };
-- 
2.1.4

[PATCH 33/35] arm64: dts: ulcb: Set drive-strength for ravb pins

[Simon Horman]

The EthernetAVB should not depend on the bootloader to setup correct
drive-strength values.  Values for drive-strength where found by
examining the registers after the bootloader has configured the
registers and successfully used the EthernetAVB.

Based on:
* commit 7d73a4da2681 ("arm64: dts: r8a7795: salvator-x: Set drive-strength
  for ravb pins")
* commit 4903987033be ("arm64: dts: r8a7796: salvator-x: Set drive-strength
  for ravb pins")

Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Niklas S?derlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
 arch/arm64/boot/dts/renesas/ulcb.dtsi | 18 ++++++++++++++++--
 1 file changed, 16 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/renesas/ulcb.dtsi b/arch/arm64/boot/dts/renesas/ulcb.dtsi
index 2bc7ceb2efa4..41e83c8530f7 100644
--- a/arch/arm64/boot/dts/renesas/ulcb.dtsi
+++ b/arch/arm64/boot/dts/renesas/ulcb.dtsi
@@ -198,8 +198,22 @@
 	pinctrl-names = "default";
 
 	avb_pins: avb {
-		groups = "avb_mdc";
-		function = "avb";
+		mux {
+			groups = "avb_link", "avb_phy_int", "avb_mdc",
+				 "avb_mii";
+			function = "avb";
+		};
+
+		pins_mdc {
+			groups = "avb_mdc";
+			drive-strength = <24>;
+		};
+
+		pins_mii_tx {
+			pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0",
+			       "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3";
+			drive-strength = <12>;
+		};
 	};
 
 	i2c2_pins: i2c2 {
-- 
2.1.4

[PATCH 34/35] arm64: dts: r8a7795: Add support for R-Car H3 ES2.0

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Update r8a7795.dtsi so it corresponds to R-Car H3 ES2.0 or later:
  - The following devices no longer exist on ES2.0, and are thus removed:
    fcpf2, fcpvd3, fcpvi2, fdp1-2, usb3-if1, vspd3, vspi2.
  - The DU <-> VSPD topology is different on ES2.0, hence remove the
    "compatible" and "vsps" properties from the DU node until the driver
    can handle this.

Move support for the ES1.x revision of the R-Car H3 SoC into a
separate file.  To avoid duplication, r8a7795-es1.dtsi includes
r8a7795.dtsi, and adds device nodes and properties where needed.
Note that while currently r8a7795-es1.dtsi only adds device nodes,
removal of devices nodes and properties can be implemented using the
/delete-node/ and /delete-property/ keywords, as shown below:

	&soc {
		/delete-node/ <name>@<addr>;
	};

	&<label> {
		/delete-property/ <prop>;
	};

Switch r8a7795-salvator-x.dts and r8a7795-h3ulcb.dts from r8a7795.dtsi
to r8a7795-es1.dtsi to preserve compatibility.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7795-es1.dtsi       | 84 ++++++++++++++++++++++
 arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts     |  4 +-
 arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts |  4 +-
 arch/arm64/boot/dts/renesas/r8a7795.dtsi           | 71 +-----------------
 4 files changed, 89 insertions(+), 74 deletions(-)
 create mode 100644 arch/arm64/boot/dts/renesas/r8a7795-es1.dtsi

diff --git a/arch/arm64/boot/dts/renesas/r8a7795-es1.dtsi b/arch/arm64/boot/dts/renesas/r8a7795-es1.dtsi
new file mode 100644
index 000000000000..a0ba7bd21ea3
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a7795-es1.dtsi
@@ -0,0 +1,84 @@
+/*
+ * Device Tree Source for the r8a7795 ES1.x SoC
+ *
+ * Copyright (C) 2015 Renesas Electronics Corp.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include "r8a7795.dtsi"
+
+&soc {
+	xhci1: usb at ee0400000 {
+		compatible = "renesas,xhci-r8a7795", "renesas,rcar-gen3-xhci";
+		reg = <0 0xee040000 0 0xc00>;
+		interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cpg CPG_MOD 327>;
+		power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+		resets = <&cpg 327>;
+		status = "disabled";
+	};
+
+	fcpf2: fcp at fe952000 {
+		compatible = "renesas,fcpf";
+		reg = <0 0xfe952000 0 0x200>;
+		clocks = <&cpg CPG_MOD 613>;
+		power-domains = <&sysc R8A7795_PD_A3VP>;
+		resets = <&cpg 613>;
+	};
+
+	vspi2: vsp at fe9c0000 {
+		compatible = "renesas,vsp2";
+		reg = <0 0xfe9c0000 0 0x8000>;
+		interrupts = <GIC_SPI 446 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cpg CPG_MOD 629>;
+		power-domains = <&sysc R8A7795_PD_A3VP>;
+		resets = <&cpg 629>;
+
+		renesas,fcp = <&fcpvi2>;
+	};
+
+	fcpvi2: fcp at fe9cf000 {
+		compatible = "renesas,fcpv";
+		reg = <0 0xfe9cf000 0 0x200>;
+		clocks = <&cpg CPG_MOD 609>;
+		power-domains = <&sysc R8A7795_PD_A3VP>;
+		resets = <&cpg 609>;
+	};
+
+	vspd3: vsp at fea38000 {
+		compatible = "renesas,vsp2";
+		reg = <0 0xfea38000 0 0x4000>;
+		interrupts = <GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cpg CPG_MOD 620>;
+		power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+		resets = <&cpg 620>;
+
+		renesas,fcp = <&fcpvd3>;
+	};
+
+	fcpvd3: fcp at fea3f000 {
+		compatible = "renesas,fcpv";
+		reg = <0 0xfea3f000 0 0x200>;
+		clocks = <&cpg CPG_MOD 600>;
+		power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+		resets = <&cpg 600>;
+	};
+
+	fdp1 at fe948000 {
+		compatible = "renesas,fdp1";
+		reg = <0 0xfe948000 0 0x2400>;
+		interrupts = <GIC_SPI 264 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cpg CPG_MOD 117>;
+		power-domains = <&sysc R8A7795_PD_A3VP>;
+		resets = <&cpg 117>;
+		renesas,fcp = <&fcpf2>;
+	};
+};
+
+&du {
+	compatible = "renesas,du-r8a7795";
+	vsps = <&vspd0 &vspd1 &vspd2 &vspd3>;
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
index a1fbf0ab8ad8..95fe207cb6a3 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
@@ -12,11 +12,11 @@
 #define CPG_AUDIO_CLK_I		R8A7795_CLK_S0D4
 
 /dts-v1/;
-#include "r8a7795.dtsi"
+#include "r8a7795-es1.dtsi"
 #include "ulcb.dtsi"
 
 / {
-	model = "Renesas H3ULCB board based on r8a7795";
+	model = "Renesas H3ULCB board based on r8a7795 ES1.x";
 	compatible = "renesas,h3ulcb", "renesas,r8a7795";
 
 	memory at 48000000 {
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
index fcd9ca73f2c7..b84c156ed696 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
@@ -11,11 +11,11 @@
 #define CPG_AUDIO_CLK_I		R8A7795_CLK_S0D4
 
 /dts-v1/;
-#include "r8a7795.dtsi"
+#include "r8a7795-es1.dtsi"
 #include "salvator-x.dtsi"
 
 / {
-	model = "Renesas Salvator-X board based on r8a7795";
+	model = "Renesas Salvator-X board based on r8a7795 ES1.x";
 	compatible = "renesas,salvator-x", "renesas,r8a7795";
 
 	memory at 48000000 {
diff --git a/arch/arm64/boot/dts/renesas/r8a7795.dtsi b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
index ee0129634cdf..24c607e30009 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
@@ -182,7 +182,7 @@
 		clock-frequency = <0>;
 	};
 
-	soc {
+	soc: soc {
 		compatible = "simple-bus";
 		interrupt-parent = <&gic>;
 
@@ -1274,16 +1274,6 @@
 			status = "disabled";
 		};
 
-		xhci1: usb at ee0400000 {
-			compatible = "renesas,xhci-r8a7795", "renesas,rcar-gen3-xhci";
-			reg = <0 0xee040000 0 0xc00>;
-			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 327>;
-			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
-			resets = <&cpg 327>;
-			status = "disabled";
-		};
-
 		usb_dmac0: dma-controller at e65a0000 {
 			compatible = "renesas,r8a7795-usb-dmac",
 				     "renesas,usb-dmac";
@@ -1568,14 +1558,6 @@
 			resets = <&cpg 614>;
 		};
 
-		fcpf2: fcp at fe952000 {
-			compatible = "renesas,fcpf";
-			reg = <0 0xfe952000 0 0x200>;
-			clocks = <&cpg CPG_MOD 613>;
-			power-domains = <&sysc R8A7795_PD_A3VP>;
-			resets = <&cpg 613>;
-		};
-
 		vspbd: vsp at fe960000 {
 			compatible = "renesas,vsp2";
 			reg = <0 0xfe960000 0 0x8000>;
@@ -1633,25 +1615,6 @@
 			resets = <&cpg 610>;
 		};
 
-		vspi2: vsp at fe9c0000 {
-			compatible = "renesas,vsp2";
-			reg = <0 0xfe9c0000 0 0x8000>;
-			interrupts = <GIC_SPI 446 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 629>;
-			power-domains = <&sysc R8A7795_PD_A3VP>;
-			resets = <&cpg 629>;
-
-			renesas,fcp = <&fcpvi2>;
-		};
-
-		fcpvi2: fcp at fe9cf000 {
-			compatible = "renesas,fcpv";
-			reg = <0 0xfe9cf000 0 0x200>;
-			clocks = <&cpg CPG_MOD 609>;
-			power-domains = <&sysc R8A7795_PD_A3VP>;
-			resets = <&cpg 609>;
-		};
-
 		vspd0: vsp at fea20000 {
 			compatible = "renesas,vsp2";
 			reg = <0 0xfea20000 0 0x4000>;
@@ -1709,25 +1672,6 @@
 			resets = <&cpg 601>;
 		};
 
-		vspd3: vsp at fea38000 {
-			compatible = "renesas,vsp2";
-			reg = <0 0xfea38000 0 0x4000>;
-			interrupts = <GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 620>;
-			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
-			resets = <&cpg 620>;
-
-			renesas,fcp = <&fcpvd3>;
-		};
-
-		fcpvd3: fcp at fea3f000 {
-			compatible = "renesas,fcpv";
-			reg = <0 0xfea3f000 0 0x200>;
-			clocks = <&cpg CPG_MOD 600>;
-			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
-			resets = <&cpg 600>;
-		};
-
 		fdp1 at fe940000 {
 			compatible = "renesas,fdp1";
 			reg = <0 0xfe940000 0 0x2400>;
@@ -1748,16 +1692,6 @@
 			renesas,fcp = <&fcpf1>;
 		};
 
-		fdp1 at fe948000 {
-			compatible = "renesas,fdp1";
-			reg = <0 0xfe948000 0 0x2400>;
-			interrupts = <GIC_SPI 264 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 117>;
-			power-domains = <&sysc R8A7795_PD_A3VP>;
-			resets = <&cpg 117>;
-			renesas,fcp = <&fcpf2>;
-		};
-
 		hdmi0: hdmi0 at fead0000 {
 			compatible = "renesas,r8a7795-hdmi", "renesas,rcar-gen3-hdmi";
 			reg = <0 0xfead0000 0 0x10000>;
@@ -1809,7 +1743,6 @@
 		};
 
 		du: display at feb00000 {
-			compatible = "renesas,du-r8a7795";
 			reg = <0 0xfeb00000 0 0x80000>,
 			      <0 0xfeb90000 0 0x14>;
 			reg-names = "du", "lvds.0";
@@ -1825,8 +1758,6 @@
 			clock-names = "du.0", "du.1", "du.2", "du.3", "lvds.0";
 			status = "disabled";
 
-			vsps = <&vspd0 &vspd1 &vspd2 &vspd3>;
-
 			ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
-- 
2.1.4

[PATCH 35/35] arm64: dts: r8a7795: salvator-x: Add support for R-Car H3 ES2.0

[Simon Horman]

From: Geert Uytterhoeven <geert+renesas@glider.be>

Split off support for Salvator-X boards with the ES1.x revision of the
R-Car H3 SoC into a separate file.  The main r8a7795-salvator-x.dts file
now corresponds to Salvator-X with R-Car H3 ES2.0 or later.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/Makefile               |   1 +
 .../boot/dts/renesas/r8a7795-es1-salvator-x.dts    | 115 +++++++++++++++++++++
 arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts |   4 +-
 3 files changed, 118 insertions(+), 2 deletions(-)
 create mode 100644 arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dts

diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile
index 1618e0a3c81d..b6c723d8f687 100644
--- a/arch/arm64/boot/dts/renesas/Makefile
+++ b/arch/arm64/boot/dts/renesas/Makefile
@@ -1,4 +1,5 @@
 dtb-$(CONFIG_ARCH_R8A7795) += r8a7795-salvator-x.dtb r8a7795-h3ulcb.dtb
+dtb-$(CONFIG_ARCH_R8A7795) += r8a7795-es1-salvator-x.dtb
 dtb-$(CONFIG_ARCH_R8A7796) += r8a7796-salvator-x.dtb r8a7796-m3ulcb.dtb
 
 always		:= $(dtb-y)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dts
new file mode 100644
index 000000000000..b84c156ed696
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dts
@@ -0,0 +1,115 @@
+/*
+ * Device Tree Source for the Salvator-X board
+ *
+ * Copyright (C) 2015 Renesas Electronics Corp.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#define CPG_AUDIO_CLK_I		R8A7795_CLK_S0D4
+
+/dts-v1/;
+#include "r8a7795-es1.dtsi"
+#include "salvator-x.dtsi"
+
+/ {
+	model = "Renesas Salvator-X board based on r8a7795 ES1.x";
+	compatible = "renesas,salvator-x", "renesas,r8a7795";
+
+	memory at 48000000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x38000000>;
+	};
+
+	memory at 500000000 {
+		device_type = "memory";
+		reg = <0x5 0x00000000 0x0 0x40000000>;
+	};
+
+	memory at 600000000 {
+		device_type = "memory";
+		reg = <0x6 0x00000000 0x0 0x40000000>;
+	};
+
+	memory at 700000000 {
+		device_type = "memory";
+		reg = <0x7 0x00000000 0x0 0x40000000>;
+	};
+};
+
+&du {
+	clocks = <&cpg CPG_MOD 724>,
+		 <&cpg CPG_MOD 723>,
+		 <&cpg CPG_MOD 722>,
+		 <&cpg CPG_MOD 721>,
+		 <&cpg CPG_MOD 727>,
+		 <&versaclock5 1>,
+		 <&x21_clk>,
+		 <&x22_clk>,
+		 <&versaclock5 2>;
+	clock-names = "du.0", "du.1", "du.2", "du.3", "lvds.0",
+		      "dclkin.0", "dclkin.1", "dclkin.2", "dclkin.3";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&hdmi0 {
+	status = "okay";
+
+	ports {
+		port at 1 {
+			reg = <1>;
+			rcar_dw_hdmi0_out: endpoint {
+				remote-endpoint = <&hdmi0_con>;
+			};
+		};
+	};
+};
+
+&hdmi0_con {
+	remote-endpoint = <&rcar_dw_hdmi0_out>;
+};
+
+&hdmi1 {
+	status = "okay";
+
+	ports {
+		port at 1 {
+			reg = <1>;
+			rcar_dw_hdmi1_out: endpoint {
+				remote-endpoint = <&hdmi1_con>;
+			};
+		};
+	};
+};
+
+&hdmi1_con {
+	remote-endpoint = <&rcar_dw_hdmi1_out>;
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&pfc {
+	usb2_pins: usb2 {
+		groups = "usb2";
+		function = "usb2";
+	};
+};
+
+&sata {
+	status = "okay";
+};
+
+&usb2_phy2 {
+	pinctrl-0 = <&usb2_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
index b84c156ed696..684fb3b9d154 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
@@ -11,11 +11,11 @@
 #define CPG_AUDIO_CLK_I		R8A7795_CLK_S0D4
 
 /dts-v1/;
-#include "r8a7795-es1.dtsi"
+#include "r8a7795.dtsi"
 #include "salvator-x.dtsi"
 
 / {
-	model = "Renesas Salvator-X board based on r8a7795 ES1.x";
+	model = "Renesas Salvator-X board based on r8a7795 ES2.0+";
 	compatible = "renesas,salvator-x", "renesas,r8a7795";
 
 	memory at 48000000 {
-- 
2.1.4

[GIT PULL] Renesas ARM64 Based SoC DT Updates for v4.13

[Olof Johansson]

On Mon, May 22, 2017 at 03:58:46PM +0200, Simon Horman wrote:
> Hi Olof, Hi Kevin, Hi Arnd,
> 
> Please consider these Renesas ARM64 based SoC DT updates for v4.13.
> 
> 
> The following changes since commit 2ea659a9ef488125eb46da6eb571de5eae5c43f6:
> 
>   Linux 4.12-rc1 (2017-05-13 13:19:49 -0700)
> 
> are available in the git repository at:
> 
>   https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-arm64-dt-for-v4.13
> 
> for you to fetch changes up to 0b03c32db03d63de695c1e0ab1950eb12b135fa7:
> 
>   arm64: dts: r8a7795: salvator-x: Add support for R-Car H3 ES2.0 (2017-05-22 14:54:57 +0200)

Merged, thanks.


-Olof