[PATCH 00/11] Add CMU/RMU/DMA support for Actions Semi S500 SoCs

[PATCH 00/11] Add CMU/RMU/DMA support for Actions Semi S500 SoCs

[Cristian Ciocaltea]

This patch series improves the existing implementation of the Clock
Management Unit for the Actions Semi S500 SoC, by adding support for
some missing clocks, like DMAC and GPIO.

Additionally, it enables the UART nodes in the common owl-s500 DTS to
use the clock provided by the CMU. That means the S500 based SBCs can
now get rid of their (fake) UART fixed clock and, as a matter of fact,
this has been already done here for RoseapplePi, the new board which
is going to be supported (hopefully) via the following patchset:
https://lore.kernel.org/lkml/cover.1592123160.git.cristian.ciocaltea@gmail.com/

Eventually, the patchset adds support for the Actions Semi S500 SoC's
DMA controller and Reset Management Unit. Please note the already
existing Actions Semi Owl SoCs DMA driver seems to be fully compatible
with S500, even though this is not explicitly mentioned in the source
code. For the moment, I have just enabled the DMA controller node in
owl-s500 DTS using the "actions,s900-dma" compatible string.

In the upcoming patch series I will provide a pinctrl driver and enable
access to MMC and I2C.

Thanks,
Cristi

Cristian Ciocaltea (11):
  clk: actions: Fix h_clk for Actions S500 SoC
  arm: dts: owl-s500: Add Clock Management Unit
  arm: dts: owl-s500: Set UART clock refs from CMU
  arm: dts: owl-s500-roseapplepi: Use UART clock from CMU
  dt-bindings: clock: Add APB, DMAC, GPIO bindings for Actions S500 SoC
  clk: actions: Add APB, DMAC, GPIO clock support for Actions S500 SoC
  arm: dts: owl-s500: Add DMA controller
  dt-bindings: reset: Add binding constants for Actions S500 RMU
  clk: actions: Add Actions S500 SoC Reset Management Unit support
  arm: dts: owl-s500: Add Reset Controller support
  MAINTAINERS: Add reset binding entry for Actions Semi Owl SoCs

 MAINTAINERS                                   |  1 +
 arch/arm/boot/dts/owl-s500-roseapplepi.dts    |  7 --
 arch/arm/boot/dts/owl-s500.dtsi               | 37 ++++++++
 drivers/clk/actions/owl-s500.c                | 91 ++++++++++++++++++-
 include/dt-bindings/clock/actions,s500-cmu.h  | 77 ++++++++--------
 .../dt-bindings/reset/actions,s500-reset.h    | 67 ++++++++++++++
 6 files changed, 235 insertions(+), 45 deletions(-)
 create mode 100644 include/dt-bindings/reset/actions,s500-reset.h

-- 
2.27.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 01/11] clk: actions: Fix h_clk for Actions S500 SoC

[Cristian Ciocaltea]

The h_clk clock in the Actions Semi S500 SoC clock driver has an
invalid parent. Replace with the correct one.

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
---
 drivers/clk/actions/owl-s500.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/clk/actions/owl-s500.c b/drivers/clk/actions/owl-s500.c
index e2007ac4d235..0eb83a0b70bc 100644
--- a/drivers/clk/actions/owl-s500.c
+++ b/drivers/clk/actions/owl-s500.c
@@ -183,7 +183,7 @@ static OWL_GATE(timer_clk, "timer_clk", "hosc", CMU_DEVCLKEN1, 27, 0, 0);
 static OWL_GATE(hdmi_clk, "hdmi_clk", "hosc", CMU_DEVCLKEN1, 3, 0, 0);
 
 /* divider clocks */
-static OWL_DIVIDER(h_clk, "h_clk", "ahbprevdiv_clk", CMU_BUSCLK1, 12, 2, NULL, 0, 0);
+static OWL_DIVIDER(h_clk, "h_clk", "ahbprediv_clk", CMU_BUSCLK1, 12, 2, NULL, 0, 0);
 static OWL_DIVIDER(rmii_ref_clk, "rmii_ref_clk", "ethernet_pll_clk", CMU_ETHERNETPLL, 1, 1, rmii_ref_div_table, 0, 0);
 
 /* factor clocks */
-- 
2.27.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 02/11] arm: dts: owl-s500: Add Clock Management Unit

[Cristian Ciocaltea]

Add Clock Management Unit for Actions Semi S500 SoC.

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
---
 arch/arm/boot/dts/owl-s500.dtsi | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/arch/arm/boot/dts/owl-s500.dtsi b/arch/arm/boot/dts/owl-s500.dtsi
index 1dbe4e8b38ac..5d5ad9db549b 100644
--- a/arch/arm/boot/dts/owl-s500.dtsi
+++ b/arch/arm/boot/dts/owl-s500.dtsi
@@ -5,6 +5,7 @@
  * Copyright (c) 2016-2017 Andreas Färber
  */
 
+#include <dt-bindings/clock/actions,s500-cmu.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/power/owl-s500-powergate.h>
 
@@ -70,6 +71,12 @@ hosc: hosc {
 		#clock-cells = <0>;
 	};
 
+	losc: losc {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		#clock-cells = <0>;
+	};
+
 	soc {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -169,6 +176,13 @@ uart6: serial@b012c000 {
 			status = "disabled";
 		};
 
+		cmu: clock-controller@b0160000 {
+			compatible = "actions,s500-cmu";
+			reg = <0xb0160000 0x8000>;
+			clocks = <&hosc>, <&losc>;
+			#clock-cells = <1>;
+		};
+
 		timer: timer@b0168000 {
 			compatible = "actions,s500-timer";
 			reg = <0xb0168000 0x8000>;
-- 
2.27.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 03/11] arm: dts: owl-s500: Set UART clock refs from CMU

[Cristian Ciocaltea]

Enable using Clock Management Unit clocks for every UART node
of the Actions Semi S500 SoC.

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
---
 arch/arm/boot/dts/owl-s500.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/boot/dts/owl-s500.dtsi b/arch/arm/boot/dts/owl-s500.dtsi
index 5d5ad9db549b..ac3d04c75dd5 100644
--- a/arch/arm/boot/dts/owl-s500.dtsi
+++ b/arch/arm/boot/dts/owl-s500.dtsi
@@ -131,6 +131,7 @@ uart0: serial@b0120000 {
 			compatible = "actions,s500-uart", "actions,owl-uart";
 			reg = <0xb0120000 0x2000>;
 			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART0>;
 			status = "disabled";
 		};
 
@@ -138,6 +139,7 @@ uart1: serial@b0122000 {
 			compatible = "actions,s500-uart", "actions,owl-uart";
 			reg = <0xb0122000 0x2000>;
 			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART1>;
 			status = "disabled";
 		};
 
@@ -145,6 +147,7 @@ uart2: serial@b0124000 {
 			compatible = "actions,s500-uart", "actions,owl-uart";
 			reg = <0xb0124000 0x2000>;
 			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART2>;
 			status = "disabled";
 		};
 
@@ -152,6 +155,7 @@ uart3: serial@b0126000 {
 			compatible = "actions,s500-uart", "actions,owl-uart";
 			reg = <0xb0126000 0x2000>;
 			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART3>;
 			status = "disabled";
 		};
 
@@ -159,6 +163,7 @@ uart4: serial@b0128000 {
 			compatible = "actions,s500-uart", "actions,owl-uart";
 			reg = <0xb0128000 0x2000>;
 			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART4>;
 			status = "disabled";
 		};
 
@@ -166,6 +171,7 @@ uart5: serial@b012a000 {
 			compatible = "actions,s500-uart", "actions,owl-uart";
 			reg = <0xb012a000 0x2000>;
 			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART5>;
 			status = "disabled";
 		};
 
@@ -173,6 +179,7 @@ uart6: serial@b012c000 {
 			compatible = "actions,s500-uart", "actions,owl-uart";
 			reg = <0xb012c000 0x2000>;
 			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu CLK_UART6>;
 			status = "disabled";
 		};
 
-- 
2.27.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 04/11] arm: dts: owl-s500-roseapplepi: Use UART clock from CMU

[Cristian Ciocaltea]

Remove the UART fixed clock and enable using the one provided by CMU.

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
---
 arch/arm/boot/dts/owl-s500-roseapplepi.dts | 7 -------
 1 file changed, 7 deletions(-)

diff --git a/arch/arm/boot/dts/owl-s500-roseapplepi.dts b/arch/arm/boot/dts/owl-s500-roseapplepi.dts
index a2087e617cb2..800edf5d2d12 100644
--- a/arch/arm/boot/dts/owl-s500-roseapplepi.dts
+++ b/arch/arm/boot/dts/owl-s500-roseapplepi.dts
@@ -25,12 +25,6 @@ memory@0 {
 		device_type = "memory";
 		reg = <0x0 0x80000000>; /* 2GB */
 	};
-
-	uart2_clk: uart2-clk {
-		compatible = "fixed-clock";
-		clock-frequency = <921600>;
-		#clock-cells = <0>;
-	};
 };
 
 &twd_timer {
@@ -43,5 +37,4 @@ &timer {
 
 &uart2 {
 	status = "okay";
-	clocks = <&uart2_clk>;
 };
-- 
2.27.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 06/11] clk: actions: Add APB, DMAC, GPIO clock support for Actions S500 SoC

[Cristian Ciocaltea]

Add support for the missing APB, DMAC and GPIO clocks in the Actions
Semi S500 SoC clock driver.

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
---
 drivers/clk/actions/owl-s500.c | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/drivers/clk/actions/owl-s500.c b/drivers/clk/actions/owl-s500.c
index 0eb83a0b70bc..025a8f6d6482 100644
--- a/drivers/clk/actions/owl-s500.c
+++ b/drivers/clk/actions/owl-s500.c
@@ -175,6 +175,8 @@ static OWL_MUX(dev_clk, "dev_clk", dev_clk_mux_p, CMU_DEVPLL, 12, 1, CLK_SET_RAT
 static OWL_MUX(ahbprediv_clk, "ahbprediv_clk", ahbprediv_clk_mux_p, CMU_BUSCLK1, 8, 3, CLK_SET_RATE_PARENT);
 
 /* gate clocks */
+static OWL_GATE(gpio_clk, "gpio_clk", "apb_clk", CMU_DEVCLKEN0, 18, 0, 0);
+static OWL_GATE(dmac_clk, "dmac_clk", "h_clk", CMU_DEVCLKEN0, 1, 0, 0);
 static OWL_GATE(spi0_clk, "spi0_clk", "ahb_clk", CMU_DEVCLKEN1, 10, 0, CLK_IGNORE_UNUSED);
 static OWL_GATE(spi1_clk, "spi1_clk", "ahb_clk", CMU_DEVCLKEN1, 11, 0, CLK_IGNORE_UNUSED);
 static OWL_GATE(spi2_clk, "spi2_clk", "ahb_clk", CMU_DEVCLKEN1, 12, 0, CLK_IGNORE_UNUSED);
@@ -184,6 +186,7 @@ static OWL_GATE(hdmi_clk, "hdmi_clk", "hosc", CMU_DEVCLKEN1, 3, 0, 0);
 
 /* divider clocks */
 static OWL_DIVIDER(h_clk, "h_clk", "ahbprediv_clk", CMU_BUSCLK1, 12, 2, NULL, 0, 0);
+static OWL_DIVIDER(apb_clk, "apb_clk", "ahb_clk", CMU_BUSCLK1, 14, 2, NULL, 0, 0);
 static OWL_DIVIDER(rmii_ref_clk, "rmii_ref_clk", "ethernet_pll_clk", CMU_ETHERNETPLL, 1, 1, rmii_ref_div_table, 0, 0);
 
 /* factor clocks */
@@ -428,6 +431,9 @@ static struct owl_clk_common *s500_clks[] = {
 	&spdif_clk.common,
 	&nand_clk.common,
 	&ecc_clk.common,
+	&apb_clk.common,
+	&dmac_clk.common,
+	&gpio_clk.common,
 };
 
 static struct clk_hw_onecell_data s500_hw_clks = {
@@ -484,6 +490,9 @@ static struct clk_hw_onecell_data s500_hw_clks = {
 		[CLK_SPDIF]		= &spdif_clk.common.hw,
 		[CLK_NAND]		= &nand_clk.common.hw,
 		[CLK_ECC]		= &ecc_clk.common.hw,
+		[CLK_APB]		= &apb_clk.common.hw,
+		[CLK_DMAC]		= &dmac_clk.common.hw,
+		[CLK_GPIO]		= &gpio_clk.common.hw,
 	},
 	.num = CLK_NR_CLKS,
 };
-- 
2.27.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 07/11] arm: dts: owl-s500: Add DMA controller

[Cristian Ciocaltea]

Add DMA controller node for Actions Semi S500 SoC.

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
---
 arch/arm/boot/dts/owl-s500.dtsi | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/arch/arm/boot/dts/owl-s500.dtsi b/arch/arm/boot/dts/owl-s500.dtsi
index ac3d04c75dd5..0f4fc5487dad 100644
--- a/arch/arm/boot/dts/owl-s500.dtsi
+++ b/arch/arm/boot/dts/owl-s500.dtsi
@@ -205,5 +205,19 @@ sps: power-controller@b01b0100 {
 			reg = <0xb01b0100 0x100>;
 			#power-domain-cells = <1>;
 		};
+
+		dma: dma-controller@b0260000 {
+			compatible = "actions,s900-dma";
+			reg = <0xb0260000 0xd00>;
+			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			dma-channels = <12>;
+			dma-requests = <46>;
+			clocks = <&cmu CLK_DMAC>;
+			power-domains = <&sps S500_PD_DMA>;
+		};
 	};
 };
-- 
2.27.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 08/11] dt-bindings: reset: Add binding constants for Actions S500 RMU

[Cristian Ciocaltea]

Add device tree binding constants for Actions Semi S500 SoC Reset
Management Unit (RMU).

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
---
 .../dt-bindings/reset/actions,s500-reset.h    | 67 +++++++++++++++++++
 1 file changed, 67 insertions(+)
 create mode 100644 include/dt-bindings/reset/actions,s500-reset.h

diff --git a/include/dt-bindings/reset/actions,s500-reset.h b/include/dt-bindings/reset/actions,s500-reset.h
new file mode 100644
index 000000000000..f5d94176d10b
--- /dev/null
+++ b/include/dt-bindings/reset/actions,s500-reset.h
@@ -0,0 +1,67 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Device Tree binding constants for Actions Semi S500 Reset Management Unit
+ *
+ * Copyright (c) 2014 Actions Semi Inc.
+ * Copyright (c) 2020 Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
+ */
+
+#ifndef __DT_BINDINGS_ACTIONS_S500_RESET_H
+#define __DT_BINDINGS_ACTIONS_S500_RESET_H
+
+#define RESET_DMAC				0
+#define RESET_NORIF				1
+#define RESET_DDR				2
+#define RESET_NANDC				3
+#define RESET_SD0				4
+#define RESET_SD1				5
+#define RESET_PCM1				6
+#define RESET_DE				7
+#define RESET_LCD				8
+#define RESET_SD2				9
+#define RESET_DSI				10
+#define RESET_CSI				11
+#define RESET_BISP				12
+#define RESET_KEY				13
+#define RESET_GPIO				14
+#define RESET_AUDIO				15
+#define RESET_PCM0				16
+#define RESET_VDE				17
+#define RESET_VCE				18
+#define RESET_GPU3D				19
+#define RESET_NIC301				20
+#define RESET_LENS				21
+#define RESET_PERIPHRESET			22
+#define RESET_USB2_0				23
+#define RESET_TVOUT				24
+#define RESET_HDMI				25
+#define RESET_HDCP2TX				26
+#define RESET_UART6				27
+#define RESET_UART0				28
+#define RESET_UART1				29
+#define RESET_UART2				30
+#define RESET_SPI0				31
+#define RESET_SPI1				32
+#define RESET_SPI2				33
+#define RESET_SPI3				34
+#define RESET_I2C0				35
+#define RESET_I2C1				36
+#define RESET_USB3				37
+#define RESET_UART3				38
+#define RESET_UART4				39
+#define RESET_UART5				40
+#define RESET_I2C2				41
+#define RESET_I2C3				42
+#define RESET_ETHERNET				43
+#define RESET_CHIPID				44
+#define RESET_USB2_1				45
+#define RESET_WD0RESET				46
+#define RESET_WD1RESET				47
+#define RESET_WD2RESET				48
+#define RESET_WD3RESET				49
+#define RESET_DBG0RESET				50
+#define RESET_DBG1RESET				51
+#define RESET_DBG2RESET				52
+#define RESET_DBG3RESET				53
+
+#endif /* __DT_BINDINGS_ACTIONS_S500_RESET_H */
-- 
2.27.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 09/11] clk: actions: Add Actions S500 SoC Reset Management Unit support

[Cristian Ciocaltea]

Add Reset Management Unit (RMU) support for Actions Semi S500 SoC.

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
---
 drivers/clk/actions/owl-s500.c | 80 ++++++++++++++++++++++++++++++++++
 1 file changed, 80 insertions(+)

diff --git a/drivers/clk/actions/owl-s500.c b/drivers/clk/actions/owl-s500.c
index 025a8f6d6482..3bce72301c65 100644
--- a/drivers/clk/actions/owl-s500.c
+++ b/drivers/clk/actions/owl-s500.c
@@ -10,6 +10,8 @@
  *
  * Copyright (c) 2018 LSI-TEC - Caninos Loucos
  * Author: Edgar Bernardi Righi <edgar.righi@lsitec.org.br>
+ *
+ * Copyright (c) 2020 Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
  */
 
 #include <linux/clk-provider.h>
@@ -23,8 +25,10 @@
 #include "owl-gate.h"
 #include "owl-mux.h"
 #include "owl-pll.h"
+#include "owl-reset.h"
 
 #include <dt-bindings/clock/actions,s500-cmu.h>
+#include <dt-bindings/reset/actions,s500-reset.h>
 
 #define CMU_COREPLL			(0x0000)
 #define CMU_DEVPLL			(0x0004)
@@ -497,20 +501,96 @@ static struct clk_hw_onecell_data s500_hw_clks = {
 	.num = CLK_NR_CLKS,
 };
 
+static const struct owl_reset_map s500_resets[] = {
+	[RESET_DMAC]	= { CMU_DEVRST0, BIT(0) },
+	[RESET_NORIF]	= { CMU_DEVRST0, BIT(1) },
+	[RESET_DDR]	= { CMU_DEVRST0, BIT(2) },
+	[RESET_NANDC]	= { CMU_DEVRST0, BIT(3) },
+	[RESET_SD0]	= { CMU_DEVRST0, BIT(4) },
+	[RESET_SD1]	= { CMU_DEVRST0, BIT(5) },
+	[RESET_PCM1]	= { CMU_DEVRST0, BIT(6) },
+	[RESET_DE]	= { CMU_DEVRST0, BIT(7) },
+	[RESET_LCD]	= { CMU_DEVRST0, BIT(8) },
+	[RESET_SD2]	= { CMU_DEVRST0, BIT(9) },
+	[RESET_DSI]	= { CMU_DEVRST0, BIT(10) },
+	[RESET_CSI]	= { CMU_DEVRST0, BIT(11) },
+	[RESET_BISP]	= { CMU_DEVRST0, BIT(12) },
+	[RESET_KEY]	= { CMU_DEVRST0, BIT(14) },
+	[RESET_GPIO]	= { CMU_DEVRST0, BIT(15) },
+	[RESET_AUDIO]	= { CMU_DEVRST0, BIT(17) },
+	[RESET_PCM0]	= { CMU_DEVRST0, BIT(18) },
+	[RESET_VDE]	= { CMU_DEVRST0, BIT(19) },
+	[RESET_VCE]	= { CMU_DEVRST0, BIT(20) },
+	[RESET_GPU3D]	= { CMU_DEVRST0, BIT(22) },
+	[RESET_NIC301]	= { CMU_DEVRST0, BIT(23) },
+	[RESET_LENS]	= { CMU_DEVRST0, BIT(26) },
+	[RESET_PERIPHRESET] = { CMU_DEVRST0, BIT(27) },
+	[RESET_USB2_0]	= { CMU_DEVRST1, BIT(0) },
+	[RESET_TVOUT]	= { CMU_DEVRST1, BIT(1) },
+	[RESET_HDMI]	= { CMU_DEVRST1, BIT(2) },
+	[RESET_HDCP2TX]	= { CMU_DEVRST1, BIT(3) },
+	[RESET_UART6]	= { CMU_DEVRST1, BIT(4) },
+	[RESET_UART0]	= { CMU_DEVRST1, BIT(5) },
+	[RESET_UART1]	= { CMU_DEVRST1, BIT(6) },
+	[RESET_UART2]	= { CMU_DEVRST1, BIT(7) },
+	[RESET_SPI0]	= { CMU_DEVRST1, BIT(8) },
+	[RESET_SPI1]	= { CMU_DEVRST1, BIT(9) },
+	[RESET_SPI2]	= { CMU_DEVRST1, BIT(10) },
+	[RESET_SPI3]	= { CMU_DEVRST1, BIT(11) },
+	[RESET_I2C0]	= { CMU_DEVRST1, BIT(12) },
+	[RESET_I2C1]	= { CMU_DEVRST1, BIT(13) },
+	[RESET_USB3]	= { CMU_DEVRST1, BIT(14) },
+	[RESET_UART3]	= { CMU_DEVRST1, BIT(15) },
+	[RESET_UART4]	= { CMU_DEVRST1, BIT(16) },
+	[RESET_UART5]	= { CMU_DEVRST1, BIT(17) },
+	[RESET_I2C2]	= { CMU_DEVRST1, BIT(18) },
+	[RESET_I2C3]	= { CMU_DEVRST1, BIT(19) },
+	[RESET_ETHERNET] = { CMU_DEVRST1, BIT(20) },
+	[RESET_CHIPID]	= { CMU_DEVRST1, BIT(21) },
+	[RESET_USB2_1]	= { CMU_DEVRST1, BIT(22) },
+	[RESET_WD0RESET] = { CMU_DEVRST1, BIT(24) },
+	[RESET_WD1RESET] = { CMU_DEVRST1, BIT(25) },
+	[RESET_WD2RESET] = { CMU_DEVRST1, BIT(26) },
+	[RESET_WD3RESET] = { CMU_DEVRST1, BIT(27) },
+	[RESET_DBG0RESET] = { CMU_DEVRST1, BIT(28) },
+	[RESET_DBG1RESET] = { CMU_DEVRST1, BIT(29) },
+	[RESET_DBG2RESET] = { CMU_DEVRST1, BIT(30) },
+	[RESET_DBG3RESET] = { CMU_DEVRST1, BIT(31) },
+};
+
 static struct owl_clk_desc s500_clk_desc = {
 	.clks	    = s500_clks,
 	.num_clks   = ARRAY_SIZE(s500_clks),
 
 	.hw_clks    = &s500_hw_clks,
+
+	.resets     = s500_resets,
+	.num_resets = ARRAY_SIZE(s500_resets),
 };
 
 static int s500_clk_probe(struct platform_device *pdev)
 {
 	struct owl_clk_desc *desc;
+	struct owl_reset *reset;
+	int ret;
 
 	desc = &s500_clk_desc;
 	owl_clk_regmap_init(pdev, desc);
 
+	reset = devm_kzalloc(&pdev->dev, sizeof(*reset), GFP_KERNEL);
+	if (!reset)
+		return -ENOMEM;
+
+	reset->rcdev.of_node = pdev->dev.of_node;
+	reset->rcdev.ops = &owl_reset_ops;
+	reset->rcdev.nr_resets = desc->num_resets;
+	reset->reset_map = desc->resets;
+	reset->regmap = desc->regmap;
+
+	ret = devm_reset_controller_register(&pdev->dev, &reset->rcdev);
+	if (ret)
+		dev_err(&pdev->dev, "Failed to register reset controller\n");
+
 	return owl_clk_probe(&pdev->dev, desc->hw_clks);
 }
 
-- 
2.27.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 10/11] arm: dts: owl-s500: Add Reset Controller support

[Cristian Ciocaltea]

Add reset controller property and bindings header for the
Actions Semi S500 SoC DTS.

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
---
 arch/arm/boot/dts/owl-s500.dtsi | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm/boot/dts/owl-s500.dtsi b/arch/arm/boot/dts/owl-s500.dtsi
index 0f4fc5487dad..0b7ba2926f0e 100644
--- a/arch/arm/boot/dts/owl-s500.dtsi
+++ b/arch/arm/boot/dts/owl-s500.dtsi
@@ -8,6 +8,7 @@
 #include <dt-bindings/clock/actions,s500-cmu.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/power/owl-s500-powergate.h>
+#include <dt-bindings/reset/actions,s500-reset.h>
 
 / {
 	compatible = "actions,s500";
@@ -188,6 +189,7 @@ cmu: clock-controller@b0160000 {
 			reg = <0xb0160000 0x8000>;
 			clocks = <&hosc>, <&losc>;
 			#clock-cells = <1>;
+			#reset-cells = <1>;
 		};
 
 		timer: timer@b0168000 {
-- 
2.27.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel