* [PATCH V11 0/4] Add minimal boot support for IPQ9574
@ 2023-04-04 10:16 Devi Priya
2023-04-04 10:16 ` [PATCH V11 1/4] dt-bindings: clock: Add ipq9574 clock and reset definitions Devi Priya
` (3 more replies)
0 siblings, 4 replies; 10+ messages in thread
From: Devi Priya @ 2023-04-04 10:16 UTC (permalink / raw)
To: agross, andersson, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt,
mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel,
shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, geert+renesas,
rafal, nfraprado, broonie, linux-arm-msm, devicetree,
linux-kernel, linux-clk, linux-gpio, linux-arm-kernel
Cc: quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav,
quic_arajkuma, quic_anusha, quic_poovendh
The IPQ9574 is Qualcomm's 802.11ax SoC for Routers,
Gateways and Access Points
This series adds minimal board boot support for ipq9574-rdp433 variant
V10 can be found at:
https://lore.kernel.org/linux-arm-kernel/20230327132718.573-1-quic_devipriy@quicinc.com/
Changes in V11:
- Detailed change log is added to the respective patches
Devi Priya (4):
dt-bindings: clock: Add ipq9574 clock and reset definitions
clk: qcom: Add Global Clock Controller driver for IPQ9574
arm64: dts: qcom: Add support for ipq9574 SoC and RDP433 variant
arm64: defconfig: Enable IPQ9574 SoC base configs
.../bindings/clock/qcom,ipq9574-gcc.yaml | 60 +
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts | 84 +
arch/arm64/boot/dts/qcom/ipq9574.dtsi | 263 +
arch/arm64/configs/defconfig | 2 +
drivers/clk/qcom/Kconfig | 8 +
drivers/clk/qcom/Makefile | 1 +
drivers/clk/qcom/gcc-ipq9574.c | 4225 +++++++++++++++++
include/dt-bindings/clock/qcom,ipq9574-gcc.h | 213 +
include/dt-bindings/reset/qcom,ipq9574-gcc.h | 164 +
10 files changed, 5021 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml
create mode 100644 arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
create mode 100644 arch/arm64/boot/dts/qcom/ipq9574.dtsi
create mode 100644 drivers/clk/qcom/gcc-ipq9574.c
create mode 100644 include/dt-bindings/clock/qcom,ipq9574-gcc.h
create mode 100644 include/dt-bindings/reset/qcom,ipq9574-gcc.h
base-commit: 31bd35b66249699343d2416658f57e97314a433a
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH V11 1/4] dt-bindings: clock: Add ipq9574 clock and reset definitions
2023-04-04 10:16 [PATCH V11 0/4] Add minimal boot support for IPQ9574 Devi Priya
@ 2023-04-04 10:16 ` Devi Priya
2023-04-04 20:14 ` Stephen Boyd
2023-04-04 10:16 ` [PATCH V11 3/4] arm64: dts: qcom: Add support for ipq9574 SoC and RDP433 variant Devi Priya
` (2 subsequent siblings)
3 siblings, 1 reply; 10+ messages in thread
From: Devi Priya @ 2023-04-04 10:16 UTC (permalink / raw)
To: agross, andersson, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt,
mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel,
shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, geert+renesas,
rafal, nfraprado, broonie, linux-arm-msm, devicetree,
linux-kernel, linux-clk, linux-gpio, linux-arm-kernel
Cc: quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav,
quic_arajkuma, quic_anusha, quic_poovendh
Add clock and reset ID definitions for ipq9574
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
---
Changes in V11:
- Dropped the clock description for Bias PLL ubi clock source
to reflect the gcc node in the DT
.../bindings/clock/qcom,ipq9574-gcc.yaml | 60 +++++
include/dt-bindings/clock/qcom,ipq9574-gcc.h | 213 ++++++++++++++++++
include/dt-bindings/reset/qcom,ipq9574-gcc.h | 164 ++++++++++++++
3 files changed, 437 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml
create mode 100644 include/dt-bindings/clock/qcom,ipq9574-gcc.h
create mode 100644 include/dt-bindings/reset/qcom,ipq9574-gcc.h
diff --git a/Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml b/Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml
new file mode 100644
index 000000000000..8581de266750
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml
@@ -0,0 +1,60 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/qcom,ipq9574-gcc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Global Clock & Reset Controller on IPQ9574
+
+maintainers:
+ - Bjorn Andersson <andersson@kernel.org>
+ - Anusha Rao <quic_anusha@quicinc.com>
+
+description: |
+ Qualcomm global clock control module provides the clocks, resets and power
+ domains on IPQ9574
+
+ See also::
+ include/dt-bindings/clock/qcom,ipq9574-gcc.h
+ include/dt-bindings/reset/qcom,ipq9574-gcc.h
+
+properties:
+ compatible:
+ const: qcom,ipq9574-gcc
+
+ clocks:
+ items:
+ - description: Board XO source
+ - description: Sleep clock source
+ - description: PCIE30 PHY0 pipe clock source
+ - description: PCIE30 PHY1 pipe clock source
+ - description: PCIE30 PHY2 pipe clock source
+ - description: PCIE30 PHY3 pipe clock source
+ - description: USB3 PHY pipe clock source
+
+required:
+ - compatible
+ - clocks
+
+allOf:
+ - $ref: qcom,gcc.yaml#
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ clock-controller@1800000 {
+ compatible = "qcom,ipq9574-gcc";
+ reg = <0x01800000 0x80000>;
+ clocks = <&xo_board_clk>,
+ <&sleep_clk>,
+ <&pcie30_phy0_pipe_clk>,
+ <&pcie30_phy1_pipe_clk>,
+ <&pcie30_phy2_pipe_clk>,
+ <&pcie30_phy3_pipe_clk>,
+ <&usb3phy_0_cc_pipe_clk>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+ };
+...
diff --git a/include/dt-bindings/clock/qcom,ipq9574-gcc.h b/include/dt-bindings/clock/qcom,ipq9574-gcc.h
new file mode 100644
index 000000000000..5a2961bfe893
--- /dev/null
+++ b/include/dt-bindings/clock/qcom,ipq9574-gcc.h
@@ -0,0 +1,213 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+/*
+ * Copyright (c) 2018-2023 The Linux Foundation. All rights reserved.
+ */
+
+#ifndef _DT_BINDINGS_CLOCK_IPQ_GCC_9574_H
+#define _DT_BINDINGS_CLOCK_IPQ_GCC_9574_H
+
+#define GPLL0_MAIN 0
+#define GPLL0 1
+#define GPLL2_MAIN 2
+#define GPLL2 3
+#define GPLL4_MAIN 4
+#define GPLL4 5
+#define GCC_SLEEP_CLK_SRC 6
+#define APSS_AHB_CLK_SRC 7
+#define APSS_AXI_CLK_SRC 8
+#define BLSP1_QUP1_I2C_APPS_CLK_SRC 9
+#define BLSP1_QUP1_SPI_APPS_CLK_SRC 10
+#define BLSP1_QUP2_I2C_APPS_CLK_SRC 11
+#define BLSP1_QUP2_SPI_APPS_CLK_SRC 12
+#define BLSP1_QUP3_I2C_APPS_CLK_SRC 13
+#define BLSP1_QUP3_SPI_APPS_CLK_SRC 14
+#define BLSP1_QUP4_I2C_APPS_CLK_SRC 15
+#define BLSP1_QUP4_SPI_APPS_CLK_SRC 16
+#define BLSP1_QUP5_I2C_APPS_CLK_SRC 17
+#define BLSP1_QUP5_SPI_APPS_CLK_SRC 18
+#define BLSP1_QUP6_I2C_APPS_CLK_SRC 19
+#define BLSP1_QUP6_SPI_APPS_CLK_SRC 20
+#define BLSP1_UART1_APPS_CLK_SRC 21
+#define BLSP1_UART2_APPS_CLK_SRC 22
+#define BLSP1_UART3_APPS_CLK_SRC 23
+#define BLSP1_UART4_APPS_CLK_SRC 24
+#define BLSP1_UART5_APPS_CLK_SRC 25
+#define BLSP1_UART6_APPS_CLK_SRC 26
+#define GCC_APSS_AHB_CLK 27
+#define GCC_APSS_AXI_CLK 28
+#define GCC_BLSP1_QUP1_I2C_APPS_CLK 29
+#define GCC_BLSP1_QUP1_SPI_APPS_CLK 30
+#define GCC_BLSP1_QUP2_I2C_APPS_CLK 31
+#define GCC_BLSP1_QUP2_SPI_APPS_CLK 32
+#define GCC_BLSP1_QUP3_I2C_APPS_CLK 33
+#define GCC_BLSP1_QUP3_SPI_APPS_CLK 34
+#define GCC_BLSP1_QUP4_I2C_APPS_CLK 35
+#define GCC_BLSP1_QUP4_SPI_APPS_CLK 36
+#define GCC_BLSP1_QUP5_I2C_APPS_CLK 37
+#define GCC_BLSP1_QUP5_SPI_APPS_CLK 38
+#define GCC_BLSP1_QUP6_I2C_APPS_CLK 39
+#define GCC_BLSP1_QUP6_SPI_APPS_CLK 40
+#define GCC_BLSP1_UART1_APPS_CLK 41
+#define GCC_BLSP1_UART2_APPS_CLK 42
+#define GCC_BLSP1_UART3_APPS_CLK 43
+#define GCC_BLSP1_UART4_APPS_CLK 44
+#define GCC_BLSP1_UART5_APPS_CLK 45
+#define GCC_BLSP1_UART6_APPS_CLK 46
+#define PCIE0_AXI_M_CLK_SRC 47
+#define GCC_PCIE0_AXI_M_CLK 48
+#define PCIE1_AXI_M_CLK_SRC 49
+#define GCC_PCIE1_AXI_M_CLK 50
+#define PCIE2_AXI_M_CLK_SRC 51
+#define GCC_PCIE2_AXI_M_CLK 52
+#define PCIE3_AXI_M_CLK_SRC 53
+#define GCC_PCIE3_AXI_M_CLK 54
+#define PCIE0_AXI_S_CLK_SRC 55
+#define GCC_PCIE0_AXI_S_BRIDGE_CLK 56
+#define GCC_PCIE0_AXI_S_CLK 57
+#define PCIE1_AXI_S_CLK_SRC 58
+#define GCC_PCIE1_AXI_S_BRIDGE_CLK 59
+#define GCC_PCIE1_AXI_S_CLK 60
+#define PCIE2_AXI_S_CLK_SRC 61
+#define GCC_PCIE2_AXI_S_BRIDGE_CLK 62
+#define GCC_PCIE2_AXI_S_CLK 63
+#define PCIE3_AXI_S_CLK_SRC 64
+#define GCC_PCIE3_AXI_S_BRIDGE_CLK 65
+#define GCC_PCIE3_AXI_S_CLK 66
+#define PCIE0_PIPE_CLK_SRC 67
+#define PCIE1_PIPE_CLK_SRC 68
+#define PCIE2_PIPE_CLK_SRC 69
+#define PCIE3_PIPE_CLK_SRC 70
+#define PCIE_AUX_CLK_SRC 71
+#define GCC_PCIE0_AUX_CLK 72
+#define GCC_PCIE1_AUX_CLK 73
+#define GCC_PCIE2_AUX_CLK 74
+#define GCC_PCIE3_AUX_CLK 75
+#define PCIE0_RCHNG_CLK_SRC 76
+#define GCC_PCIE0_RCHNG_CLK 77
+#define PCIE1_RCHNG_CLK_SRC 78
+#define GCC_PCIE1_RCHNG_CLK 79
+#define PCIE2_RCHNG_CLK_SRC 80
+#define GCC_PCIE2_RCHNG_CLK 81
+#define PCIE3_RCHNG_CLK_SRC 82
+#define GCC_PCIE3_RCHNG_CLK 83
+#define GCC_PCIE0_AHB_CLK 84
+#define GCC_PCIE1_AHB_CLK 85
+#define GCC_PCIE2_AHB_CLK 86
+#define GCC_PCIE3_AHB_CLK 87
+#define USB0_AUX_CLK_SRC 88
+#define GCC_USB0_AUX_CLK 89
+#define USB0_MASTER_CLK_SRC 90
+#define GCC_USB0_MASTER_CLK 91
+#define GCC_SNOC_USB_CLK 92
+#define GCC_ANOC_USB_AXI_CLK 93
+#define USB0_MOCK_UTMI_CLK_SRC 94
+#define USB0_MOCK_UTMI_DIV_CLK_SRC 95
+#define GCC_USB0_MOCK_UTMI_CLK 96
+#define USB0_PIPE_CLK_SRC 97
+#define GCC_USB0_PHY_CFG_AHB_CLK 98
+#define SDCC1_APPS_CLK_SRC 99
+#define GCC_SDCC1_APPS_CLK 100
+#define SDCC1_ICE_CORE_CLK_SRC 101
+#define GCC_SDCC1_ICE_CORE_CLK 102
+#define GCC_SDCC1_AHB_CLK 103
+#define PCNOC_BFDCD_CLK_SRC 104
+#define GCC_NSSCFG_CLK 105
+#define GCC_NSSNOC_NSSCC_CLK 106
+#define GCC_NSSCC_CLK 107
+#define GCC_NSSNOC_PCNOC_1_CLK 108
+#define GCC_QDSS_DAP_AHB_CLK 109
+#define GCC_QDSS_CFG_AHB_CLK 110
+#define GCC_QPIC_AHB_CLK 111
+#define GCC_QPIC_CLK 112
+#define GCC_BLSP1_AHB_CLK 113
+#define GCC_MDIO_AHB_CLK 114
+#define GCC_PRNG_AHB_CLK 115
+#define GCC_UNIPHY0_AHB_CLK 116
+#define GCC_UNIPHY1_AHB_CLK 117
+#define GCC_UNIPHY2_AHB_CLK 118
+#define GCC_CMN_12GPLL_AHB_CLK 119
+#define GCC_CMN_12GPLL_APU_CLK 120
+#define SYSTEM_NOC_BFDCD_CLK_SRC 121
+#define GCC_NSSNOC_SNOC_CLK 122
+#define GCC_NSSNOC_SNOC_1_CLK 123
+#define GCC_QDSS_ETR_USB_CLK 124
+#define WCSS_AHB_CLK_SRC 125
+#define GCC_Q6_AHB_CLK 126
+#define GCC_Q6_AHB_S_CLK 127
+#define GCC_WCSS_ECAHB_CLK 128
+#define GCC_WCSS_ACMT_CLK 129
+#define GCC_SYS_NOC_WCSS_AHB_CLK 130
+#define WCSS_AXI_M_CLK_SRC 131
+#define GCC_ANOC_WCSS_AXI_M_CLK 132
+#define QDSS_AT_CLK_SRC 133
+#define GCC_Q6SS_ATBM_CLK 134
+#define GCC_WCSS_DBG_IFC_ATB_CLK 135
+#define GCC_NSSNOC_ATB_CLK 136
+#define GCC_QDSS_AT_CLK 137
+#define GCC_SYS_NOC_AT_CLK 138
+#define GCC_PCNOC_AT_CLK 139
+#define GCC_USB0_EUD_AT_CLK 140
+#define GCC_QDSS_EUD_AT_CLK 141
+#define QDSS_STM_CLK_SRC 142
+#define GCC_QDSS_STM_CLK 143
+#define GCC_SYS_NOC_QDSS_STM_AXI_CLK 144
+#define QDSS_TRACECLKIN_CLK_SRC 145
+#define GCC_QDSS_TRACECLKIN_CLK 146
+#define QDSS_TSCTR_CLK_SRC 147
+#define GCC_Q6_TSCTR_1TO2_CLK 148
+#define GCC_WCSS_DBG_IFC_NTS_CLK 149
+#define GCC_QDSS_TSCTR_DIV2_CLK 150
+#define GCC_QDSS_TS_CLK 151
+#define GCC_QDSS_TSCTR_DIV4_CLK 152
+#define GCC_NSS_TS_CLK 153
+#define GCC_QDSS_TSCTR_DIV8_CLK 154
+#define GCC_QDSS_TSCTR_DIV16_CLK 155
+#define GCC_Q6SS_PCLKDBG_CLK 156
+#define GCC_Q6SS_TRIG_CLK 157
+#define GCC_WCSS_DBG_IFC_APB_CLK 158
+#define GCC_WCSS_DBG_IFC_DAPBUS_CLK 159
+#define GCC_QDSS_DAP_CLK 160
+#define GCC_QDSS_APB2JTAG_CLK 161
+#define GCC_QDSS_TSCTR_DIV3_CLK 162
+#define QPIC_IO_MACRO_CLK_SRC 163
+#define GCC_QPIC_IO_MACRO_CLK 164
+#define Q6_AXI_CLK_SRC 165
+#define GCC_Q6_AXIM_CLK 166
+#define GCC_WCSS_Q6_TBU_CLK 167
+#define GCC_MEM_NOC_Q6_AXI_CLK 168
+#define Q6_AXIM2_CLK_SRC 169
+#define NSSNOC_MEMNOC_BFDCD_CLK_SRC 170
+#define GCC_NSSNOC_MEMNOC_CLK 171
+#define GCC_NSSNOC_MEM_NOC_1_CLK 172
+#define GCC_NSS_TBU_CLK 173
+#define GCC_MEM_NOC_NSSNOC_CLK 174
+#define LPASS_AXIM_CLK_SRC 175
+#define LPASS_SWAY_CLK_SRC 176
+#define ADSS_PWM_CLK_SRC 177
+#define GCC_ADSS_PWM_CLK 178
+#define GP1_CLK_SRC 179
+#define GP2_CLK_SRC 180
+#define GP3_CLK_SRC 181
+#define DDRSS_SMS_SLOW_CLK_SRC 182
+#define GCC_XO_CLK_SRC 183
+#define GCC_XO_CLK 184
+#define GCC_NSSNOC_QOSGEN_REF_CLK 185
+#define GCC_NSSNOC_TIMEOUT_REF_CLK 186
+#define GCC_XO_DIV4_CLK 187
+#define GCC_UNIPHY0_SYS_CLK 188
+#define GCC_UNIPHY1_SYS_CLK 189
+#define GCC_UNIPHY2_SYS_CLK 190
+#define GCC_CMN_12GPLL_SYS_CLK 191
+#define GCC_NSSNOC_XO_DCD_CLK 192
+#define GCC_Q6SS_BOOT_CLK 193
+#define UNIPHY_SYS_CLK_SRC 194
+#define NSS_TS_CLK_SRC 195
+#define GCC_ANOC_PCIE0_1LANE_M_CLK 196
+#define GCC_ANOC_PCIE1_1LANE_M_CLK 197
+#define GCC_ANOC_PCIE2_2LANE_M_CLK 198
+#define GCC_ANOC_PCIE3_2LANE_M_CLK 199
+#define GCC_SNOC_PCIE0_1LANE_S_CLK 200
+#define GCC_SNOC_PCIE1_1LANE_S_CLK 201
+#define GCC_SNOC_PCIE2_2LANE_S_CLK 202
+#define GCC_SNOC_PCIE3_2LANE_S_CLK 203
+#endif
diff --git a/include/dt-bindings/reset/qcom,ipq9574-gcc.h b/include/dt-bindings/reset/qcom,ipq9574-gcc.h
new file mode 100644
index 000000000000..d01dc6a24cf1
--- /dev/null
+++ b/include/dt-bindings/reset/qcom,ipq9574-gcc.h
@@ -0,0 +1,164 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+/*
+ * Copyright (c) 2018-2023, The Linux Foundation. All rights reserved.
+ */
+
+#ifndef _DT_BINDINGS_RESET_IPQ_GCC_9574_H
+#define _DT_BINDINGS_RESET_IPQ_GCC_9574_H
+
+#define GCC_ADSS_BCR 0
+#define GCC_APC0_VOLTAGE_DROOP_DETECTOR_BCR 1
+#define GCC_BLSP1_BCR 2
+#define GCC_BLSP1_QUP1_BCR 3
+#define GCC_BLSP1_QUP2_BCR 4
+#define GCC_BLSP1_QUP3_BCR 5
+#define GCC_BLSP1_QUP4_BCR 6
+#define GCC_BLSP1_QUP5_BCR 7
+#define GCC_BLSP1_QUP6_BCR 8
+#define GCC_BLSP1_UART1_BCR 9
+#define GCC_BLSP1_UART2_BCR 10
+#define GCC_BLSP1_UART3_BCR 11
+#define GCC_BLSP1_UART4_BCR 12
+#define GCC_BLSP1_UART5_BCR 13
+#define GCC_BLSP1_UART6_BCR 14
+#define GCC_BOOT_ROM_BCR 15
+#define GCC_MDIO_BCR 16
+#define GCC_NSS_BCR 17
+#define GCC_NSS_TBU_BCR 18
+#define GCC_PCIE0_BCR 19
+#define GCC_PCIE0_LINK_DOWN_BCR 20
+#define GCC_PCIE0_PHY_BCR 21
+#define GCC_PCIE0PHY_PHY_BCR 22
+#define GCC_PCIE1_BCR 23
+#define GCC_PCIE1_LINK_DOWN_BCR 24
+#define GCC_PCIE1_PHY_BCR 25
+#define GCC_PCIE1PHY_PHY_BCR 26
+#define GCC_PCIE2_BCR 27
+#define GCC_PCIE2_LINK_DOWN_BCR 28
+#define GCC_PCIE2_PHY_BCR 29
+#define GCC_PCIE2PHY_PHY_BCR 30
+#define GCC_PCIE3_BCR 31
+#define GCC_PCIE3_LINK_DOWN_BCR 32
+#define GCC_PCIE3_PHY_BCR 33
+#define GCC_PCIE3PHY_PHY_BCR 34
+#define GCC_PRNG_BCR 35
+#define GCC_QUSB2_0_PHY_BCR 36
+#define GCC_SDCC_BCR 37
+#define GCC_TLMM_BCR 38
+#define GCC_UNIPHY0_BCR 39
+#define GCC_UNIPHY1_BCR 40
+#define GCC_UNIPHY2_BCR 41
+#define GCC_USB0_PHY_BCR 42
+#define GCC_USB3PHY_0_PHY_BCR 43
+#define GCC_USB_BCR 44
+#define GCC_ANOC0_TBU_BCR 45
+#define GCC_ANOC1_TBU_BCR 46
+#define GCC_ANOC_BCR 47
+#define GCC_APSS_TCU_BCR 48
+#define GCC_CMN_BLK_BCR 49
+#define GCC_CMN_BLK_AHB_ARES 50
+#define GCC_CMN_BLK_SYS_ARES 51
+#define GCC_CMN_BLK_APU_ARES 52
+#define GCC_DCC_BCR 53
+#define GCC_DDRSS_BCR 54
+#define GCC_IMEM_BCR 55
+#define GCC_LPASS_BCR 56
+#define GCC_MPM_BCR 57
+#define GCC_MSG_RAM_BCR 58
+#define GCC_NSSNOC_MEMNOC_1_ARES 59
+#define GCC_NSSNOC_PCNOC_1_ARES 60
+#define GCC_NSSNOC_SNOC_1_ARES 61
+#define GCC_NSSNOC_XO_DCD_ARES 62
+#define GCC_NSSNOC_TS_ARES 63
+#define GCC_NSSCC_ARES 64
+#define GCC_NSSNOC_NSSCC_ARES 65
+#define GCC_NSSNOC_ATB_ARES 66
+#define GCC_NSSNOC_MEMNOC_ARES 67
+#define GCC_NSSNOC_QOSGEN_REF_ARES 68
+#define GCC_NSSNOC_SNOC_ARES 69
+#define GCC_NSSNOC_TIMEOUT_REF_ARES 70
+#define GCC_NSS_CFG_ARES 71
+#define GCC_UBI0_DBG_ARES 72
+#define GCC_PCIE0_AHB_ARES 73
+#define GCC_PCIE0_AUX_ARES 74
+#define GCC_PCIE0_AXI_M_ARES 75
+#define GCC_PCIE0_AXI_M_STICKY_ARES 76
+#define GCC_PCIE0_AXI_S_ARES 77
+#define GCC_PCIE0_AXI_S_STICKY_ARES 78
+#define GCC_PCIE0_CORE_STICKY_ARES 79
+#define GCC_PCIE0_PIPE_ARES 80
+#define GCC_PCIE1_AHB_ARES 81
+#define GCC_PCIE1_AUX_ARES 82
+#define GCC_PCIE1_AXI_M_ARES 83
+#define GCC_PCIE1_AXI_M_STICKY_ARES 84
+#define GCC_PCIE1_AXI_S_ARES 85
+#define GCC_PCIE1_AXI_S_STICKY_ARES 86
+#define GCC_PCIE1_CORE_STICKY_ARES 87
+#define GCC_PCIE1_PIPE_ARES 88
+#define GCC_PCIE2_AHB_ARES 89
+#define GCC_PCIE2_AUX_ARES 90
+#define GCC_PCIE2_AXI_M_ARES 91
+#define GCC_PCIE2_AXI_M_STICKY_ARES 92
+#define GCC_PCIE2_AXI_S_ARES 93
+#define GCC_PCIE2_AXI_S_STICKY_ARES 94
+#define GCC_PCIE2_CORE_STICKY_ARES 95
+#define GCC_PCIE2_PIPE_ARES 96
+#define GCC_PCIE3_AHB_ARES 97
+#define GCC_PCIE3_AUX_ARES 98
+#define GCC_PCIE3_AXI_M_ARES 99
+#define GCC_PCIE3_AXI_M_STICKY_ARES 100
+#define GCC_PCIE3_AXI_S_ARES 101
+#define GCC_PCIE3_AXI_S_STICKY_ARES 102
+#define GCC_PCIE3_CORE_STICKY_ARES 103
+#define GCC_PCIE3_PIPE_ARES 104
+#define GCC_PCNOC_BCR 105
+#define GCC_PCNOC_BUS_TIMEOUT0_BCR 106
+#define GCC_PCNOC_BUS_TIMEOUT1_BCR 107
+#define GCC_PCNOC_BUS_TIMEOUT2_BCR 108
+#define GCC_PCNOC_BUS_TIMEOUT3_BCR 109
+#define GCC_PCNOC_BUS_TIMEOUT4_BCR 110
+#define GCC_PCNOC_BUS_TIMEOUT5_BCR 111
+#define GCC_PCNOC_BUS_TIMEOUT6_BCR 112
+#define GCC_PCNOC_BUS_TIMEOUT7_BCR 113
+#define GCC_PCNOC_BUS_TIMEOUT8_BCR 114
+#define GCC_PCNOC_BUS_TIMEOUT9_BCR 115
+#define GCC_PCNOC_TBU_BCR 116
+#define GCC_Q6SS_DBG_ARES 117
+#define GCC_Q6_AHB_ARES 118
+#define GCC_Q6_AHB_S_ARES 119
+#define GCC_Q6_AXIM2_ARES 120
+#define GCC_Q6_AXIM_ARES 121
+#define GCC_QDSS_BCR 122
+#define GCC_QPIC_BCR 123
+#define GCC_QPIC_AHB_ARES 124
+#define GCC_QPIC_ARES 125
+#define GCC_RBCPR_BCR 126
+#define GCC_RBCPR_MX_BCR 127
+#define GCC_SEC_CTRL_BCR 128
+#define GCC_SMMU_CFG_BCR 129
+#define GCC_SNOC_BCR 130
+#define GCC_SPDM_BCR 131
+#define GCC_TME_BCR 132
+#define GCC_UNIPHY0_SYS_RESET 133
+#define GCC_UNIPHY0_AHB_RESET 134
+#define GCC_UNIPHY0_XPCS_RESET 135
+#define GCC_UNIPHY1_SYS_RESET 136
+#define GCC_UNIPHY1_AHB_RESET 137
+#define GCC_UNIPHY1_XPCS_RESET 138
+#define GCC_UNIPHY2_SYS_RESET 139
+#define GCC_UNIPHY2_AHB_RESET 140
+#define GCC_UNIPHY2_XPCS_RESET 141
+#define GCC_USB_MISC_RESET 142
+#define GCC_WCSSAON_RESET 143
+#define GCC_WCSS_ACMT_ARES 144
+#define GCC_WCSS_AHB_S_ARES 145
+#define GCC_WCSS_AXI_M_ARES 146
+#define GCC_WCSS_BCR 147
+#define GCC_WCSS_DBG_ARES 148
+#define GCC_WCSS_DBG_BDG_ARES 149
+#define GCC_WCSS_ECAHB_ARES 150
+#define GCC_WCSS_Q6_BCR 151
+#define GCC_WCSS_Q6_TBU_BCR 152
+#define GCC_TCSR_BCR 153
+
+#endif
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH V11 3/4] arm64: dts: qcom: Add support for ipq9574 SoC and RDP433 variant
2023-04-04 10:16 [PATCH V11 0/4] Add minimal boot support for IPQ9574 Devi Priya
2023-04-04 10:16 ` [PATCH V11 1/4] dt-bindings: clock: Add ipq9574 clock and reset definitions Devi Priya
@ 2023-04-04 10:16 ` Devi Priya
2023-04-04 11:03 ` Marc Zyngier
2023-04-04 10:16 ` [PATCH V11 4/4] arm64: defconfig: Enable IPQ9574 SoC base configs Devi Priya
[not found] ` <20230404101622.5394-3-quic_devipriy@quicinc.com>
3 siblings, 1 reply; 10+ messages in thread
From: Devi Priya @ 2023-04-04 10:16 UTC (permalink / raw)
To: agross, andersson, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt,
mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel,
shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, geert+renesas,
rafal, nfraprado, broonie, linux-arm-msm, devicetree,
linux-kernel, linux-clk, linux-gpio, linux-arm-kernel
Cc: quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav,
quic_arajkuma, quic_anusha, quic_poovendh
Add initial device tree support for Qualcomm IPQ9574 SoC and
Reference Design Platform(RDP) 433 which is based on IPQ9574
family of SoCs
Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
Co-developed-by: Poovendhan Selvaraj <quic_poovendh@quicinc.com>
Signed-off-by: Poovendhan Selvaraj <quic_poovendh@quicinc.com>
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
---
Changes in V11:
- Dropped the unused backup clock source bias_pll_ubi_nc_clk
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts | 84 +++++++
arch/arm64/boot/dts/qcom/ipq9574.dtsi | 263 ++++++++++++++++++++
3 files changed, 348 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
create mode 100644 arch/arm64/boot/dts/qcom/ipq9574.dtsi
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 1a29403400b7..52f1f92c5195 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -8,6 +8,7 @@ dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb
dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb
dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c1.dtb
dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c2.dtb
+dtb-$(CONFIG_ARCH_QCOM) += ipq9574-rdp433.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-acer-a1-724.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-alcatel-idol347.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-asus-z00l.dtb
diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
new file mode 100644
index 000000000000..2ce8e09e7565
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
@@ -0,0 +1,84 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * IPQ9574 RDP433 board device tree source
+ *
+ * Copyright (c) 2020-2021 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "ipq9574.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C7";
+ compatible = "qcom,ipq9574-ap-al02-c7", "qcom,ipq9574";
+
+ aliases {
+ serial0 = &blsp1_uart2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&blsp1_uart2 {
+ pinctrl-0 = <&uart2_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&sdhc_1 {
+ pinctrl-0 = <&sdc_default_state>;
+ pinctrl-names = "default";
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+ max-frequency = <384000000>;
+ bus-width = <8>;
+ status = "okay";
+};
+
+&sleep_clk {
+ clock-frequency = <32000>;
+};
+
+&tlmm {
+ sdc_default_state: sdc-default-state {
+ clk-pins {
+ pins = "gpio5";
+ function = "sdc_clk";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ cmd-pins {
+ pins = "gpio4";
+ function = "sdc_cmd";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ data-pins {
+ pins = "gpio0", "gpio1", "gpio2",
+ "gpio3", "gpio6", "gpio7",
+ "gpio8", "gpio9";
+ function = "sdc_data";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ rclk-pins {
+ pins = "gpio10";
+ function = "sdc_rclk";
+ drive-strength = <8>;
+ bias-pull-down;
+ };
+ };
+};
+
+&xo_board_clk {
+ clock-frequency = <24000000>;
+};
diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
new file mode 100644
index 000000000000..c0e35308d8e0
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
@@ -0,0 +1,263 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * IPQ9574 SoC device tree source
+ *
+ * Copyright (c) 2020-2021 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,ipq9574-gcc.h>
+#include <dt-bindings/reset/qcom,ipq9574-gcc.h>
+
+/ {
+ interrupt-parent = <&intc>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ clocks {
+ sleep_clk: sleep-clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ };
+
+ xo_board_clk: xo-board-clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ };
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ CPU0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73";
+ reg = <0x0>;
+ enable-method = "psci";
+ next-level-cache = <&L2_0>;
+ };
+
+ CPU1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73";
+ reg = <0x1>;
+ enable-method = "psci";
+ next-level-cache = <&L2_0>;
+ };
+
+ CPU2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73";
+ reg = <0x2>;
+ enable-method = "psci";
+ next-level-cache = <&L2_0>;
+ };
+
+ CPU3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73";
+ reg = <0x3>;
+ enable-method = "psci";
+ next-level-cache = <&L2_0>;
+ };
+
+ L2_0: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
+ };
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ /* We expect the bootloader to fill in the size */
+ reg = <0x0 0x40000000 0x0 0x0>;
+ };
+
+ pmu {
+ compatible = "arm,cortex-a73-pmu";
+ interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ tz_region: tz@4a600000 {
+ reg = <0x0 0x4a600000 0x0 0x400000>;
+ no-map;
+ };
+ };
+
+ soc: soc@0 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0 0xffffffff>;
+
+ tlmm: pinctrl@1000000 {
+ compatible = "qcom,ipq9574-tlmm";
+ reg = <0x01000000 0x300000>;
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&tlmm 0 0 65>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ uart2_pins: uart2-state {
+ pins = "gpio34", "gpio35";
+ function = "blsp2_uart";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ gcc: clock-controller@1800000 {
+ compatible = "qcom,ipq9574-gcc";
+ reg = <0x01800000 0x80000>;
+ clocks = <&xo_board_clk>,
+ <&sleep_clk>,
+ <0>,
+ <0>,
+ <0>,
+ <0>,
+ <0>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+ };
+
+ sdhc_1: mmc@7804000 {
+ compatible = "qcom,ipq9574-sdhci", "qcom,sdhci-msm-v5";
+ reg = <0x07804000 0x1000>, <0x07805000 0x1000>;
+ reg-names = "hc", "cqhci";
+
+ interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hc_irq", "pwr_irq";
+
+ clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+ <&gcc GCC_SDCC1_APPS_CLK>,
+ <&xo_board_clk>;
+ clock-names = "iface", "core", "xo";
+ non-removable;
+ status = "disabled";
+ };
+
+ blsp1_uart2: serial@78b1000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x078b1000 0x200>;
+ interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+ };
+
+ intc: interrupt-controller@b000000 {
+ compatible = "qcom,msm-qgic2";
+ reg = <0x0b000000 0x1000>, /* GICD */
+ <0x0b002000 0x1000>, /* GICC */
+ <0x0b001000 0x1000>, /* GICH */
+ <0x0b004000 0x1000>; /* GICV */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ ranges = <0 0x0b00c000 0x3000>;
+
+ v2m0: v2m@0 {
+ compatible = "arm,gic-v2m-frame";
+ reg = <0x00000000 0xffd>;
+ msi-controller;
+ };
+
+ v2m1: v2m@1000 {
+ compatible = "arm,gic-v2m-frame";
+ reg = <0x00001000 0xffd>;
+ msi-controller;
+ };
+
+ v2m2: v2m@2000 {
+ compatible = "arm,gic-v2m-frame";
+ reg = <0x00002000 0xffd>;
+ msi-controller;
+ };
+ };
+
+ timer@b120000 {
+ compatible = "arm,armv7-timer-mem";
+ reg = <0x0b120000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ frame@b120000 {
+ reg = <0x0b121000 0x1000>,
+ <0x0b122000 0x1000>;
+ frame-number = <0>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ frame@b123000 {
+ reg = <0x0b123000 0x1000>;
+ frame-number = <1>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ frame@b124000 {
+ reg = <0x0b124000 0x1000>;
+ frame-number = <2>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ frame@b125000 {
+ reg = <0x0b125000 0x1000>;
+ frame-number = <3>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ frame@b126000 {
+ reg = <0x0b126000 0x1000>;
+ frame-number = <4>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ frame@b127000 {
+ reg = <0x0b127000 0x1000>;
+ frame-number = <5>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ frame@b128000 {
+ reg = <0x0b128000 0x1000>;
+ frame-number = <6>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+};
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH V11 4/4] arm64: defconfig: Enable IPQ9574 SoC base configs
2023-04-04 10:16 [PATCH V11 0/4] Add minimal boot support for IPQ9574 Devi Priya
2023-04-04 10:16 ` [PATCH V11 1/4] dt-bindings: clock: Add ipq9574 clock and reset definitions Devi Priya
2023-04-04 10:16 ` [PATCH V11 3/4] arm64: dts: qcom: Add support for ipq9574 SoC and RDP433 variant Devi Priya
@ 2023-04-04 10:16 ` Devi Priya
[not found] ` <20230404101622.5394-3-quic_devipriy@quicinc.com>
3 siblings, 0 replies; 10+ messages in thread
From: Devi Priya @ 2023-04-04 10:16 UTC (permalink / raw)
To: agross, andersson, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt,
mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel,
shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, geert+renesas,
rafal, nfraprado, broonie, linux-arm-msm, devicetree,
linux-kernel, linux-clk, linux-gpio, linux-arm-kernel
Cc: quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav,
quic_arajkuma, quic_anusha, quic_poovendh
Enables clk & pinctrl related configs for Qualcomm IPQ9574 SoC
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
---
arch/arm64/configs/defconfig | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 29c79a6a85eb..8f24c280dec2 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -557,6 +557,7 @@ CONFIG_PINCTRL_MSM=y
CONFIG_PINCTRL_IPQ8074=y
CONFIG_PINCTRL_IPQ5332=y
CONFIG_PINCTRL_IPQ6018=y
+CONFIG_PINCTRL_IPQ9574=y
CONFIG_PINCTRL_MSM8916=y
CONFIG_PINCTRL_MSM8953=y
CONFIG_PINCTRL_MSM8976=y
@@ -1155,6 +1156,7 @@ CONFIG_QCOM_CLK_RPMH=y
CONFIG_IPQ_GCC_5332=y
CONFIG_IPQ_GCC_6018=y
CONFIG_IPQ_GCC_8074=y
+CONFIG_IPQ_GCC_9574=y
CONFIG_MSM_GCC_8916=y
CONFIG_MSM_GCC_8994=y
CONFIG_MSM_MMCC_8994=m
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: [PATCH V11 3/4] arm64: dts: qcom: Add support for ipq9574 SoC and RDP433 variant
2023-04-04 10:16 ` [PATCH V11 3/4] arm64: dts: qcom: Add support for ipq9574 SoC and RDP433 variant Devi Priya
@ 2023-04-04 11:03 ` Marc Zyngier
2023-04-07 10:21 ` Devi Priya
0 siblings, 1 reply; 10+ messages in thread
From: Marc Zyngier @ 2023-04-04 11:03 UTC (permalink / raw)
To: Devi Priya
Cc: agross, andersson, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt,
mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel,
shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, geert+renesas,
rafal, nfraprado, broonie, linux-arm-msm, devicetree,
linux-kernel, linux-clk, linux-gpio, linux-arm-kernel,
quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav,
quic_arajkuma, quic_anusha, quic_poovendh
On 2023-04-04 11:16, Devi Priya wrote:
> Add initial device tree support for Qualcomm IPQ9574 SoC and
> Reference Design Platform(RDP) 433 which is based on IPQ9574
> family of SoCs
>
> Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
> Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
> Co-developed-by: Poovendhan Selvaraj <quic_poovendh@quicinc.com>
> Signed-off-by: Poovendhan Selvaraj <quic_poovendh@quicinc.com>
> Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
> ---
> Changes in V11:
> - Dropped the unused backup clock source bias_pll_ubi_nc_clk
>
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts | 84 +++++++
> arch/arm64/boot/dts/qcom/ipq9574.dtsi | 263 ++++++++++++++++++++
> 3 files changed, 348 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
> create mode 100644 arch/arm64/boot/dts/qcom/ipq9574.dtsi
>
[...]
> + intc: interrupt-controller@b000000 {
> + compatible = "qcom,msm-qgic2";
> + reg = <0x0b000000 0x1000>, /* GICD */
> + <0x0b002000 0x1000>, /* GICC */
This is definitely wrong. The GICC region cannot be less than
8kB, as the GICC_DIR register is in the second 4kB region.
I'm pretty sure the kernel shouts at you when booting at EL2.
> + <0x0b001000 0x1000>, /* GICH */
> + <0x0b004000 0x1000>; /* GICV */
Same thing here.
> + #address-cells = <1>;
> + #size-cells = <1>;
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
Missing target CPU encoding.
M.
--
Jazz is not dead. It just smells funny...
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH V11 1/4] dt-bindings: clock: Add ipq9574 clock and reset definitions
2023-04-04 10:16 ` [PATCH V11 1/4] dt-bindings: clock: Add ipq9574 clock and reset definitions Devi Priya
@ 2023-04-04 20:14 ` Stephen Boyd
0 siblings, 0 replies; 10+ messages in thread
From: Stephen Boyd @ 2023-04-04 20:14 UTC (permalink / raw)
To: Devi Priya, agross, andersson, arnd, broonie, catalin.marinas,
devicetree, dmitry.baryshkov, geert+renesas, konrad.dybcio,
krzysztof.kozlowski+dt, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-clk, linux-gpio, linux-kernel,
marcel.ziswiler, mturquette, nfraprado, p.zabel, rafal, robh+dt,
shawnguo, will
Cc: quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav,
quic_arajkuma, quic_anusha, quic_poovendh
Quoting Devi Priya (2023-04-04 03:16:19)
> Add clock and reset ID definitions for ipq9574
>
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
> Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
> Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
> ---
Acked-by: Stephen Boyd <sboyd@kernel.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH V11 2/4] clk: qcom: Add Global Clock Controller driver for IPQ9574
[not found] ` <20230404101622.5394-3-quic_devipriy@quicinc.com>
@ 2023-04-04 20:14 ` Stephen Boyd
0 siblings, 0 replies; 10+ messages in thread
From: Stephen Boyd @ 2023-04-04 20:14 UTC (permalink / raw)
To: Devi Priya, agross, andersson, arnd, broonie, catalin.marinas,
devicetree, dmitry.baryshkov, geert+renesas, konrad.dybcio,
krzysztof.kozlowski+dt, linus.walleij, linux-arm-kernel,
linux-arm-msm, linux-clk, linux-gpio, linux-kernel,
marcel.ziswiler, mturquette, nfraprado, p.zabel, rafal, robh+dt,
shawnguo, will
Cc: quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav,
quic_arajkuma, quic_anusha, quic_poovendh
Quoting Devi Priya (2023-04-04 03:16:20)
> Add Global Clock Controller (GCC) driver for ipq9574 based devices
>
> Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
> Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
> Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
> ---
Acked-by: Stephen Boyd <sboyd@kernel.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH V11 3/4] arm64: dts: qcom: Add support for ipq9574 SoC and RDP433 variant
2023-04-04 11:03 ` Marc Zyngier
@ 2023-04-07 10:21 ` Devi Priya
2023-04-07 14:06 ` Marc Zyngier
0 siblings, 1 reply; 10+ messages in thread
From: Devi Priya @ 2023-04-07 10:21 UTC (permalink / raw)
To: Marc Zyngier
Cc: agross, andersson, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt,
mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel,
shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, geert+renesas,
rafal, nfraprado, broonie, linux-arm-msm, devicetree,
linux-kernel, linux-clk, linux-gpio, linux-arm-kernel,
quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav,
quic_arajkuma, quic_anusha, quic_poovendh
On 4/4/2023 4:33 PM, Marc Zyngier wrote:
> On 2023-04-04 11:16, Devi Priya wrote:
>> Add initial device tree support for Qualcomm IPQ9574 SoC and
>> Reference Design Platform(RDP) 433 which is based on IPQ9574
>> family of SoCs
>>
>> Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
>> Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
>> Co-developed-by: Poovendhan Selvaraj <quic_poovendh@quicinc.com>
>> Signed-off-by: Poovendhan Selvaraj <quic_poovendh@quicinc.com>
>> Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
>> ---
>> Changes in V11:
>> - Dropped the unused backup clock source bias_pll_ubi_nc_clk
>>
>> arch/arm64/boot/dts/qcom/Makefile | 1 +
>> arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts | 84 +++++++
>> arch/arm64/boot/dts/qcom/ipq9574.dtsi | 263 ++++++++++++++++++++
>> 3 files changed, 348 insertions(+)
>> create mode 100644 arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
>> create mode 100644 arch/arm64/boot/dts/qcom/ipq9574.dtsi
>>
>
> [...]
>
>> + intc: interrupt-controller@b000000 {
>> + compatible = "qcom,msm-qgic2";
>> + reg = <0x0b000000 0x1000>, /* GICD */
>> + <0x0b002000 0x1000>, /* GICC */
>
> This is definitely wrong. The GICC region cannot be less than
> 8kB, as the GICC_DIR register is in the second 4kB region.
>
> I'm pretty sure the kernel shouts at you when booting at EL2.
Got it, will update the size to 8kB
>
>> + <0x0b001000 0x1000>, /* GICH */
>> + <0x0b004000 0x1000>; /* GICV */
>
> Same thing here.
okay
>
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + interrupt-controller;
>> + #interrupt-cells = <3>;
>> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
>
> Missing target CPU encoding.
Okay, will update the interrupts as below. Hope this is the expectation?
Please let us know if we are missing something
interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
>
> M.
Best Regards,
Devi Priya
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH V11 3/4] arm64: dts: qcom: Add support for ipq9574 SoC and RDP433 variant
2023-04-07 10:21 ` Devi Priya
@ 2023-04-07 14:06 ` Marc Zyngier
2023-04-07 14:09 ` Devi Priya
0 siblings, 1 reply; 10+ messages in thread
From: Marc Zyngier @ 2023-04-07 14:06 UTC (permalink / raw)
To: Devi Priya
Cc: agross, andersson, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt,
mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel,
shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, geert+renesas,
rafal, nfraprado, broonie, linux-arm-msm, devicetree,
linux-kernel, linux-clk, linux-gpio, linux-arm-kernel,
quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav,
quic_arajkuma, quic_anusha, quic_poovendh
On 2023-04-07 11:21, Devi Priya wrote:
> On 4/4/2023 4:33 PM, Marc Zyngier wrote:
>> On 2023-04-04 11:16, Devi Priya wrote:
>>> + #address-cells = <1>;
>>> + #size-cells = <1>;
>>> + interrupt-controller;
>>> + #interrupt-cells = <3>;
>>> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
>>
>> Missing target CPU encoding.
> Okay, will update the interrupts as below. Hope this is the
> expectation?
> Please let us know if we are missing something
> interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) |
> IRQ_TYPE_LEVEL_HIGH)>;
Yup.
M.
--
Jazz is not dead. It just smells funny...
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH V11 3/4] arm64: dts: qcom: Add support for ipq9574 SoC and RDP433 variant
2023-04-07 14:06 ` Marc Zyngier
@ 2023-04-07 14:09 ` Devi Priya
0 siblings, 0 replies; 10+ messages in thread
From: Devi Priya @ 2023-04-07 14:09 UTC (permalink / raw)
To: Marc Zyngier
Cc: agross, andersson, konrad.dybcio, robh+dt, krzysztof.kozlowski+dt,
mturquette, sboyd, linus.walleij, catalin.marinas, will, p.zabel,
shawnguo, arnd, marcel.ziswiler, dmitry.baryshkov, geert+renesas,
rafal, nfraprado, broonie, linux-arm-msm, devicetree,
linux-kernel, linux-clk, linux-gpio, linux-arm-kernel,
quic_srichara, quic_gokulsri, quic_sjaganat, quic_kathirav,
quic_arajkuma, quic_anusha, quic_poovendh
On 4/7/2023 7:36 PM, Marc Zyngier wrote:
> On 2023-04-07 11:21, Devi Priya wrote:
>> On 4/4/2023 4:33 PM, Marc Zyngier wrote:
>>> On 2023-04-04 11:16, Devi Priya wrote:
>>>> + #address-cells = <1>;
>>>> + #size-cells = <1>;
>>>> + interrupt-controller;
>>>> + #interrupt-cells = <3>;
>>>> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
>>>
>>> Missing target CPU encoding.
>> Okay, will update the interrupts as below. Hope this is the expectation?
>> Please let us know if we are missing something
>> interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
>
> Yup.
Thanks!
>
> M.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2023-04-07 14:10 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2023-04-04 10:16 [PATCH V11 0/4] Add minimal boot support for IPQ9574 Devi Priya
2023-04-04 10:16 ` [PATCH V11 1/4] dt-bindings: clock: Add ipq9574 clock and reset definitions Devi Priya
2023-04-04 20:14 ` Stephen Boyd
2023-04-04 10:16 ` [PATCH V11 3/4] arm64: dts: qcom: Add support for ipq9574 SoC and RDP433 variant Devi Priya
2023-04-04 11:03 ` Marc Zyngier
2023-04-07 10:21 ` Devi Priya
2023-04-07 14:06 ` Marc Zyngier
2023-04-07 14:09 ` Devi Priya
2023-04-04 10:16 ` [PATCH V11 4/4] arm64: defconfig: Enable IPQ9574 SoC base configs Devi Priya
[not found] ` <20230404101622.5394-3-quic_devipriy@quicinc.com>
2023-04-04 20:14 ` [PATCH V11 2/4] clk: qcom: Add Global Clock Controller driver for IPQ9574 Stephen Boyd
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).