RE: [PATCH v5 3/8] dt-bindings: mfd: realtek,rtd1xxx: Add interrupt controller child node

["Yu-Chun Lin [林祐君]" <eleanor.lin@realtek.com>]

Hi Krzysztof,

Sorry for the late reply.

> On 22/10/2026 08:44, Yu-Chun Lin [林祐君] wrote:
> > Hi Krzysztof,
> >
> >>>>>  patternProperties:
> >>>>> +  "^interrupt-controller":
> >>>>> +    $ref: /schemas/interrupt-controller/realtek,rtd1319-intc-iso.yaml
> >>>>> +    unevaluatedProperties: false
> >>>>> +
> >>>>>    '@[0-9a-f]+$':
> >>>>>      type: object
> >>>>
> >>>> What is this for then? Should it be removed?
> >>>>
> >>>
> >>> The original syscon compatible has other child nodes that do have 'reg'
> >>> properties and unit addresses, so this pattern is still needed for them.
> >>>
> >>>>>
> >>>>> @@ -76,3 +80,27 @@ required:
> >>>>>    - reg
> >>>>>
> >>>>>  additionalProperties: false
> >>>>> +
> >>>>> +examples:
> >>>>> +  - |
> >>>>> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> >>>>> +    #include <dt-bindings/interrupt-controller/irq.h>
> >>>>> +
> >>>>> +    syscon@7000 {
> >>>>> +        compatible = "realtek,rtd1625-iso", "syscon", "simple-mfd";
> >>>>> +        reg = <0x7000 0x1000>;
> >>>>> +        ranges = <0x0 0x7000 0x1000>;
> >>>>> +        #address-cells = <1>;
> >>>>> +        #size-cells = <1>;
> >>>>
> >>>> Why do you have cells it your child has no addressing?
> >>>>
> >>>>> +
> >>>>> +        interrupt-controller {
> >>>>
> >>>> So the binding requires children with unit address, yes?
> >>>>
> >>>
> >>> The interrupt-controller does not need a unit address because it
> >>> accesses the registers via the parent's regmap.
> >>
> >> That's not really relevant. Child drivers still access via parent's
> >> regmap and have unit address. This binding has bus addressing for
> >> children, so use it. Do not add random or inconsistent code.
> >>
> >
> > The registers for interrupt controller are quite scattered within the
> > parent syscon block. Take rtd1625-intc-misc as an example, the offsets
> > are 0x4, 0xc, 0x80, and 0x88 After adding unit-address and reg.
> > It would be like:
> >
> > interrupt-controller@4 {
> >     compatible = "realtek,rtd1625-intc-misc";
> >     reg = <0x4 0x4>,
> >           <0xc 0x4>,
> >           <0x80 0x4>,
> >           <0x88 0x4>;
> >     interrupt-controller;
> 
> That would mean that this device is instead part of the parent. If you do not
> have separate address space, how is it a separate device?
> 

I will drop the separate interrupt-controller node and make the syscon
node itself the interrupt controller:

syscon node would look like this:

	iso: syscon@7000 {
		compatible = "realtek,rtd1625-iso-syscon", "syscon", "simple-mfd";
		reg = <0x7000 0x1000>;
		interrupts-extended = <&gic GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
                              <&gic GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
                              <&gic GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
		interrupt-controller;
		#interrupt-cells = <1>;
	};

In addition, I would like to confirm one thing.
The iso syscon region (0x7000-0x7fff) overlaps with the existing
uart0 node (serial@7800) in kent.dtsi [1]. Is this overlap
acceptable?

[1] https://elixir.bootlin.com/linux/v7.3-rc1/source/arch/arm64/boot/dts/realtek/kent.dtsi#L144

};
> >     ...
> > };
> >
> > Could you please confirm if this is the correct and preferred approach?
> >
> >>>
> >>> Will update the example to remove the unnecessary properties from
> >>> the parent as follows:
> >>>
> >>> syscon@7000 {
> >>>     compatible = "realtek,rtd1625-iso", "syscon", "simple-mfd";
> >>>     reg = <0x7000 0x1000>;
> >>>
> >>
> >> Still incomplete. Where are other devices?
> >>
> >
> > In the past, Andreas used a generic '@[0-9a-f]+$"' to match child nodes.
> > Because of this, in older SoCs (e.g., rtd129x.dtsi, rtd16xx.dtsi,
> > rtd139x.dtsi), devices like reset-controller, watchdog, and serial
> > were allowed and placed under the iso or misc syscon nodes.
> >
> > However, I have some doubts about continuing to use that exact structure:
> >
> > 1. We previously discussed and agreed [1] that devices like serial
> > should actually be placed under rbus, not syscon.
> > 2. For the SoCs introduced in this patch (rtd1319,rtd1319d, rtd1325,
> > rtd1625), the drivers for the other child devices (like watchdog) are
> > not upstreamed yet.
> >
> > To properly fix the "incomplete example" for the simple-mfd structure,
> > could you please advise:
> >
> > 1. Should I replace the generic '@[0-9a-f]+$' in the YAML binding with
> > explicit device definitions for these specific child nodes?
> > 2. For the example section, should I just populate it with
> > placeholders (e.g., watchdog) referencing Andreas's older DTs (like
> > rtd129x.dtsi) to illustrate the MFD structure?
> >
> > [1]
> > https://lore.kernel.org/lkml/15951264289d44f797ebd4e05238b380@realtek.
> > com/
> 
> If you know that existing pattern is not really correct, please do not grow it.

Understood. I will leave the old binding as it is.

Best Regards,
Yu-Chun