[PATCH 21/52] mtd: rawnand: jz4780: convert driver to nand_scan()

[harveyhuntnexus@gmail.com (Harvey Hunt)]

Hi Miquel,

Sorry it's taken me a little while to review your changes, a few
comments below:

On 03/02/2018 05:03 PM, Miquel Raynal wrote:
> Two helpers have been added to the core to make ECC-related
> configuration between the detection phase and the final NAND scan. Use
> these hooks and convert the driver to just use nand_scan() instead of
> both nand_scan_ident() and nand_scan_tail().
> 
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> ---
>  drivers/mtd/nand/raw/jz4780_nand.c | 30 ++++++++++++------------------
>  1 file changed, 12 insertions(+), 18 deletions(-)
> 
> diff --git a/drivers/mtd/nand/raw/jz4780_nand.c b/drivers/mtd/nand/raw/jz4780_nand.c
> index e69f6ae4c539..fd5dc9d9b0c6 100644
> --- a/drivers/mtd/nand/raw/jz4780_nand.c
> +++ b/drivers/mtd/nand/raw/jz4780_nand.c
> @@ -157,9 +157,8 @@ static int jz4780_nand_ecc_correct(struct mtd_info *mtd, u8 *dat,
>  	return jz4780_bch_correct(nfc->bch, &params, dat, read_ecc);
>  }
>  
> -static int jz4780_nand_init_ecc(struct jz4780_nand_chip *nand, struct device *dev)
> +static int jz4780_nand_attach_chip(struct nand_chip *chip)
>  {
> -	struct nand_chip *chip = &nand->chip;
>  	struct mtd_info *mtd = nand_to_mtd(chip);
>  	struct jz4780_nand_controller *nfc = to_jz4780_nand_controller(chip->controller);
>  	int eccbytes;
> @@ -170,7 +169,8 @@ static int jz4780_nand_init_ecc(struct jz4780_nand_chip *nand, struct device *de
>  	switch (chip->ecc.mode) {
>  	case NAND_ECC_HW:
>  		if (!nfc->bch) {
> -			dev_err(dev, "HW BCH selected, but BCH controller not found\n");
> +			dev_err(nfc->dev,
> +				"HW BCH selected, but BCH controller not found\n");
>  			return -ENODEV;
>  		}
>  
> @@ -179,15 +179,16 @@ static int jz4780_nand_init_ecc(struct jz4780_nand_chip *nand, struct device *de
>  		chip->ecc.correct = jz4780_nand_ecc_correct;
>  		/* fall through */
>  	case NAND_ECC_SOFT:
> -		dev_info(dev, "using %s (strength %d, size %d, bytes %d)\n",
> -			(nfc->bch) ? "hardware BCH" : "software ECC",
> -			chip->ecc.strength, chip->ecc.size, chip->ecc.bytes);
> +		dev_info(nfc->dev, "using %s (strength %d, size %d, bytes %d)\n",
> +			 (nfc->bch) ? "hardware BCH" : "software ECC",
> +			 chip->ecc.strength, chip->ecc.size, chip->ecc.bytes)>  		break;
>  	case NAND_ECC_NONE:
> -		dev_info(dev, "not using ECC\n");
> +		dev_info(nfc->dev, "not using ECC\n");
>  		break;
>  	default:
> -		dev_err(dev, "ECC mode %d not supported\n", chip->ecc.mode);
> +		dev_err(nfc->dev, "ECC mode %d not supported\n",
> +			chip->ecc.mode);
>  		return -EINVAL;
>  	}
These changes seem redundant as dev is passed into the function,
although you could remove it from the function defintion.

>  
> @@ -199,7 +200,7 @@ static int jz4780_nand_init_ecc(struct jz4780_nand_chip *nand, struct device *de
>  	eccbytes = mtd->writesize / chip->ecc.size * chip->ecc.bytes;
>  
>  	if (eccbytes > mtd->oobsize - 2) {
> -		dev_err(dev,
> +		dev_err(nfc->dev,
>  			"invalid ECC config: required %d ECC bytes, but only %d are available",
>  			eccbytes, mtd->oobsize - 2);
>  		return -EINVAL;
> @@ -279,15 +280,8 @@ static int jz4780_nand_init_chip(struct platform_device *pdev,
>  	chip->controller = &nfc->controller;
>  	nand_set_flash_node(chip, np);
>  
> -	ret = nand_scan_ident(mtd, 1, NULL);
> -	if (ret)
> -		return ret;
> -
> -	ret = jz4780_nand_init_ecc(nand, dev)

You've removed this call, but without it the ECC won't be initialised...

> -	if (ret)
> -		return ret;
> -
> -	ret = nand_scan_tail(mtd);
> +	chip->ecc.attach_chip = jz4780_nand_attach_chip;

This function doesn't exist.

> +	ret = nand_scan(mtd, 1);
>  	if (ret)
>  		return ret;
>  
> 

Thanks,

Harvey