From: Vladimir Zapolskiy <vz@mleia.com>
To: Frank Li <Frank.li@nxp.com>
Cc: Piotr Wojtaszczyk <piotr.wojtaszczyk@timesys.com>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
"moderated list:ARM/LPC32XX SOC SUPPORT"
<linux-arm-kernel@lists.infradead.org>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@vger.kernel.org>,
open list <linux-kernel@vger.kernel.org>,
imx@lists.linux.dev
Subject: Re: [PATCH v2 5/5] ARM: dts: lpc3250-phy3250: remove deprecated at25* property
Date: Mon, 17 Nov 2025 21:05:50 +0200 [thread overview]
Message-ID: <e0c3885d-6db6-404e-b31e-a7674d96e10a@mleia.com> (raw)
In-Reply-To: <aRtJdTMxFaXdVnvs@lizhi-Precision-Tower-5810>
On 11/17/25 18:12, Frank Li wrote:
> On Sat, Nov 15, 2025 at 02:23:50AM +0200, Vladimir Zapolskiy wrote:
>> On 11/14/25 19:47, Frank Li wrote:
>>> Remove duplicated deprecated at25* property because the same common
>>> property already were added.
>>>
>>> Signed-off-by: Frank Li <Frank.Li@nxp.com>
>>> ---
>>> changes in v2
>>> - new patch
>>> ---
>>> arch/arm/boot/dts/nxp/lpc/lpc3250-phy3250.dts | 4 ----
>>> 1 file changed, 4 deletions(-)
>>>
>>> diff --git a/arch/arm/boot/dts/nxp/lpc/lpc3250-phy3250.dts b/arch/arm/boot/dts/nxp/lpc/lpc3250-phy3250.dts
>>> index 15463a96938cc..0f96ea0337a1f 100644
>>> --- a/arch/arm/boot/dts/nxp/lpc/lpc3250-phy3250.dts
>>> +++ b/arch/arm/boot/dts/nxp/lpc/lpc3250-phy3250.dts
>>> @@ -213,10 +213,6 @@ eeprom: eeprom@0 {
>>> pl022,wait-state = <0>;
>>> pl022,duplex = <0>;
>>> - at25,byte-len = <0x8000>;
>>> - at25,addr-mode = <2>;
>>> - at25,page-size = <64>;
>>> -
>>> size = <0x8000>;
>>> address-width = <16>;
>>> pagesize = <64>;
>>
>> Just squash this change with the 3/5 from the series, or I can do it on
>> patch application.
>
> Yes, you can squash when apply.
>
Good, no need to resend these changes for you, but I would skip sending
a PR for v6.19, the patches will be targeted for v6.20.
>>
>> My ask about splitting the changes was about a separation of the 4/5 change,
>> and it was done as expected, thank you.
--
Best wishes,
Vladimir
next prev parent reply other threads:[~2025-11-17 19:06 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-11-14 17:47 [PATCH v2 1/5] ARM: dts: lpc32xx: remove usb bus and elevate all children nodes Frank Li
2025-11-14 17:47 ` [PATCH v2 2/5] ARM: dts: lpc3250-ea3250: add key- prefix for gpio-keys Frank Li
2025-11-14 17:47 ` [PATCH v2 3/5] ARM: dts: lpc3250-phy3250: add at25 required properties Frank Li
2025-11-15 0:16 ` Vladimir Zapolskiy
2025-11-14 17:47 ` [PATCH v2 4/5] ARM: dts: lpc3250-phy3250: rename nodename at@0 to eeprom@0 Frank Li
2025-11-15 0:16 ` Vladimir Zapolskiy
2025-11-14 17:47 ` [PATCH v2 5/5] ARM: dts: lpc3250-phy3250: remove deprecated at25* property Frank Li
2025-11-15 0:23 ` Vladimir Zapolskiy
2025-11-17 16:12 ` Frank Li
2025-11-17 19:05 ` Vladimir Zapolskiy [this message]
2025-11-15 0:20 ` [PATCH v2 1/5] ARM: dts: lpc32xx: remove usb bus and elevate all children nodes Vladimir Zapolskiy
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=e0c3885d-6db6-404e-b31e-a7674d96e10a@mleia.com \
--to=vz@mleia.com \
--cc=Frank.li@nxp.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=imx@lists.linux.dev \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=piotr.wojtaszczyk@timesys.com \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox