[PATCH 0/5] GPIO descriptor cleanup for some Wolfson codecs

[PATCH 0/5] GPIO descriptor cleanup for some Wolfson codecs

[Linus Walleij]

This converts the remaining Wolfson ASoC codecs to
use GPIO descriptors.

These Wolfson codecs are mostly used with different
Samsung S3C (especially Cragganmore 6410) board files,
so the in-tree users are fixed up in the process.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
Linus Walleij (5):
      ASoC: wm0010: Convert to GPIO descriptors
      ASoC: wm1250-ev1: Convert to GPIO descriptors
      ASoC: wm2200: Convert to GPIO descriptors
      ASoC: wm5100: Convert to GPIO descriptors
      ASoC: wm8996: Convert to GPIO descriptors

 arch/arm/mach-s3c/mach-crag6410-module.c |  60 ++++++++++++----
 arch/arm/mach-s3c/mach-crag6410.c        |  24 +++----
 include/sound/wm0010.h                   |   6 --
 include/sound/wm1250-ev1.h               |  24 -------
 include/sound/wm2200.h                   |   2 -
 include/sound/wm5100.h                   |   4 --
 include/sound/wm8996.h                   |   3 -
 sound/soc/codecs/wm0010.c                |  44 +++---------
 sound/soc/codecs/wm1250-ev1.c            | 118 ++++++++++++-------------------
 sound/soc/codecs/wm2200.c                |  67 +++++++++---------
 sound/soc/codecs/wm5100.c                | 107 ++++++++++------------------
 sound/soc/codecs/wm8996.c                |  58 +++++++--------
 12 files changed, 211 insertions(+), 306 deletions(-)
---
base-commit: cbf5552fa580b78c690ca5829264f2fd2e2bafc1
change-id: 20231205-descriptors-sound-wlf-e6caec3cc642

Best regards,
-- 
Linus Walleij <linus.walleij@linaro.org>


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 1/5] ASoC: wm0010: Convert to GPIO descriptors

[Linus Walleij]

This converts the WM0010 codec to use GPIO descriptors.
It's a pretty straight-forward conversion also switching over
the single in-tree user in the S3C Cragganmore module
for S3C 6410.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 arch/arm/mach-s3c/mach-crag6410-module.c | 16 +++++++++---
 include/sound/wm0010.h                   |  6 -----
 sound/soc/codecs/wm0010.c                | 44 ++++++++------------------------
 3 files changed, 23 insertions(+), 43 deletions(-)

diff --git a/arch/arm/mach-s3c/mach-crag6410-module.c b/arch/arm/mach-s3c/mach-crag6410-module.c
index 8fce1e815ee8..a9a713641047 100644
--- a/arch/arm/mach-s3c/mach-crag6410-module.c
+++ b/arch/arm/mach-s3c/mach-crag6410-module.c
@@ -32,9 +32,18 @@
 
 #include "crag6410.h"
 
+static struct gpiod_lookup_table wm0010_gpiod_table = {
+	.dev_id = "spi0.0", /* SPI device name */
+	.table = {
+		/* Active high for Glenfarclas Rev 2 */
+		GPIO_LOOKUP("GPION", 6,
+			    "reset", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 static struct wm0010_pdata wm0010_pdata = {
-	.gpio_reset = S3C64XX_GPN(6),
-	.reset_active_high = 1, /* Active high for Glenfarclas Rev 2 */
+	/* Intentionally left blank */
 };
 
 static struct spi_board_info wm1253_devs[] = {
@@ -337,7 +346,8 @@ static const struct {
 	{ .id = 0x21, .rev = 0xff, .name = "1275-EV1 Mortlach" },
 	{ .id = 0x25, .rev = 0xff, .name = "1274-EV1 Glencadam" },
 	{ .id = 0x31, .rev = 0xff, .name = "1253-EV1 Tomatin",
-	  .spi_devs = wm1253_devs, .num_spi_devs = ARRAY_SIZE(wm1253_devs) },
+	  .spi_devs = wm1253_devs, .num_spi_devs = ARRAY_SIZE(wm1253_devs),
+	  .gpiod_table = &wm0010_gpiod_table },
 	{ .id = 0x32, .rev = 0xff, .name = "XXXX-EV1 Caol Illa" },
 	{ .id = 0x33, .rev = 0xff, .name = "XXXX-EV1 Oban" },
 	{ .id = 0x34, .rev = 0xff, .name = "WM0010-6320-CS42 Balblair",
diff --git a/include/sound/wm0010.h b/include/sound/wm0010.h
index 13b473935ca1..14ff9056c5d0 100644
--- a/include/sound/wm0010.h
+++ b/include/sound/wm0010.h
@@ -11,12 +11,6 @@
 #define WM0010_PDATA_H
 
 struct wm0010_pdata {
-	int gpio_reset;
-
-	/* Set if there is an inverter between the GPIO controlling
-	 * the reset signal and the device.
-	 */
-	int reset_active_high;
 	int irq_flags;
 };
 
diff --git a/sound/soc/codecs/wm0010.c b/sound/soc/codecs/wm0010.c
index 1d4259433f47..8f862729a2ca 100644
--- a/sound/soc/codecs/wm0010.c
+++ b/sound/soc/codecs/wm0010.c
@@ -18,7 +18,7 @@
 #include <linux/firmware.h>
 #include <linux/delay.h>
 #include <linux/fs.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/regulator/consumer.h>
 #include <linux/mutex.h>
 #include <linux/workqueue.h>
@@ -94,8 +94,7 @@ struct wm0010_priv {
 
 	struct wm0010_pdata pdata;
 
-	int gpio_reset;
-	int gpio_reset_value;
+	struct gpio_desc *reset;
 
 	struct regulator_bulk_data core_supplies[2];
 	struct regulator *dbvdd;
@@ -174,8 +173,7 @@ static void wm0010_halt(struct snd_soc_component *component)
 	case WM0010_STAGE2:
 	case WM0010_FIRMWARE:
 		/* Remember to put chip back into reset */
-		gpio_set_value_cansleep(wm0010->gpio_reset,
-					wm0010->gpio_reset_value);
+		gpiod_set_value_cansleep(wm0010->reset, 1);
 		/* Disable the regulators */
 		regulator_disable(wm0010->dbvdd);
 		regulator_bulk_disable(ARRAY_SIZE(wm0010->core_supplies),
@@ -610,7 +608,7 @@ static int wm0010_boot(struct snd_soc_component *component)
 	}
 
 	/* Release reset */
-	gpio_set_value_cansleep(wm0010->gpio_reset, !wm0010->gpio_reset_value);
+	gpiod_set_value_cansleep(wm0010->reset, 0);
 	spin_lock_irqsave(&wm0010->irq_lock, flags);
 	wm0010->state = WM0010_OUT_OF_RESET;
 	spin_unlock_irqrestore(&wm0010->irq_lock, flags);
@@ -863,7 +861,6 @@ static int wm0010_probe(struct snd_soc_component *component)
 
 static int wm0010_spi_probe(struct spi_device *spi)
 {
-	unsigned long gpio_flags;
 	int ret;
 	int trigger;
 	int irq;
@@ -903,31 +900,11 @@ static int wm0010_spi_probe(struct spi_device *spi)
 		return ret;
 	}
 
-	if (wm0010->pdata.gpio_reset) {
-		wm0010->gpio_reset = wm0010->pdata.gpio_reset;
-
-		if (wm0010->pdata.reset_active_high)
-			wm0010->gpio_reset_value = 1;
-		else
-			wm0010->gpio_reset_value = 0;
-
-		if (wm0010->gpio_reset_value)
-			gpio_flags = GPIOF_OUT_INIT_HIGH;
-		else
-			gpio_flags = GPIOF_OUT_INIT_LOW;
-
-		ret = devm_gpio_request_one(wm0010->dev, wm0010->gpio_reset,
-					    gpio_flags, "wm0010 reset");
-		if (ret < 0) {
-			dev_err(wm0010->dev,
-				"Failed to request GPIO for DSP reset: %d\n",
-				ret);
-			return ret;
-		}
-	} else {
-		dev_err(wm0010->dev, "No reset GPIO configured\n");
-		return -EINVAL;
-	}
+	wm0010->reset = devm_gpiod_get(wm0010->dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(wm0010->reset))
+		return dev_err_probe(wm0010->dev, PTR_ERR(wm0010->reset),
+				     "could not get RESET GPIO\n");
+	gpiod_set_consumer_name(wm0010->reset, "wm0010 reset");
 
 	wm0010->state = WM0010_POWER_OFF;
 
@@ -972,8 +949,7 @@ static void wm0010_spi_remove(struct spi_device *spi)
 {
 	struct wm0010_priv *wm0010 = spi_get_drvdata(spi);
 
-	gpio_set_value_cansleep(wm0010->gpio_reset,
-				wm0010->gpio_reset_value);
+	gpiod_set_value_cansleep(wm0010->reset, 1);
 
 	irq_set_irq_wake(wm0010->irq, 0);
 

-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 2/5] ASoC: wm1250-ev1: Convert to GPIO descriptors

[Linus Walleij]

This converts the WM1250-EV1 codec to use GPIO descriptors.
It turns out that the platform data was only used to pass some
global GPIO numbers from a board file, so we get rid of this
and also switch over the single in-tree user in the S3C
Cragganmore module for S3C 6410.

The driver obtains two GPIO lines named OSR and master and just
pull them low, we leave this behaviour as it was.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 arch/arm/mach-s3c/mach-crag6410.c |  24 ++++----
 include/sound/wm1250-ev1.h        |  24 --------
 sound/soc/codecs/wm1250-ev1.c     | 118 ++++++++++++++------------------------
 3 files changed, 56 insertions(+), 110 deletions(-)

diff --git a/arch/arm/mach-s3c/mach-crag6410.c b/arch/arm/mach-s3c/mach-crag6410.c
index 7c4bed4370a1..e5df2cb51ab2 100644
--- a/arch/arm/mach-s3c/mach-crag6410.c
+++ b/arch/arm/mach-s3c/mach-crag6410.c
@@ -39,8 +39,6 @@
 #include <linux/mfd/wm831x/irq.h>
 #include <linux/mfd/wm831x/gpio.h>
 
-#include <sound/wm1250-ev1.h>
-
 #include <asm/mach/arch.h>
 #include <asm/mach-types.h>
 
@@ -713,13 +711,16 @@ static struct wm831x_pdata glenfarclas_pmic_pdata = {
 	.disable_touch = true,
 };
 
-static struct wm1250_ev1_pdata wm1250_ev1_pdata = {
-	.gpios = {
-		[WM1250_EV1_GPIO_CLK_ENA] = S3C64XX_GPN(12),
-		[WM1250_EV1_GPIO_CLK_SEL0] = S3C64XX_GPL(12),
-		[WM1250_EV1_GPIO_CLK_SEL1] = S3C64XX_GPL(13),
-		[WM1250_EV1_GPIO_OSR] = S3C64XX_GPL(14),
-		[WM1250_EV1_GPIO_MASTER] = S3C64XX_GPL(8),
+static struct gpiod_lookup_table crag_wm1250_ev1_gpiod_table = {
+	/* The WM1250-EV1 is device 0027 on I2C bus 1 */
+	.dev_id = "1-0027",
+	.table = {
+		GPIO_LOOKUP("GPION", 12, "clk-ena", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("GPIOL", 12, "clk-sel0", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("GPIOL", 13, "clk-sel1", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("GPIOL", 14, "osr", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("GPIOL", 8, "master", GPIO_ACTIVE_HIGH),
+		{ },
 	},
 };
 
@@ -733,9 +734,7 @@ static struct i2c_board_info i2c_devs1[] = {
 	{ I2C_BOARD_INFO("wlf-gf-module", 0x24) },
 	{ I2C_BOARD_INFO("wlf-gf-module", 0x25) },
 	{ I2C_BOARD_INFO("wlf-gf-module", 0x26) },
-
-	{ I2C_BOARD_INFO("wm1250-ev1", 0x27),
-	  .platform_data = &wm1250_ev1_pdata },
+	{ I2C_BOARD_INFO("wm1250-ev1", 0x27), },
 };
 
 static struct s3c2410_platform_i2c i2c1_pdata = {
@@ -862,6 +861,7 @@ static void __init crag6410_machine_init(void)
 
 	gpiod_add_lookup_table(&crag_pmic_gpiod_table);
 	i2c_register_board_info(0, i2c_devs0, ARRAY_SIZE(i2c_devs0));
+	gpiod_add_lookup_table(&crag_wm1250_ev1_gpiod_table);
 	i2c_register_board_info(1, i2c_devs1, ARRAY_SIZE(i2c_devs1));
 
 	samsung_keypad_set_platdata(&crag6410_keypad_data);
diff --git a/include/sound/wm1250-ev1.h b/include/sound/wm1250-ev1.h
deleted file mode 100644
index d16614ebecb4..000000000000
--- a/include/sound/wm1250-ev1.h
+++ /dev/null
@@ -1,24 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * linux/sound/wm1250-ev1.h - Platform data for WM1250-EV1
- *
- * Copyright 2011 Wolfson Microelectronics. PLC.
- */
-
-#ifndef __LINUX_SND_WM1250_EV1_H
-#define __LINUX_SND_WM1250_EV1_H
-
-#define WM1250_EV1_NUM_GPIOS 5
-
-#define WM1250_EV1_GPIO_CLK_ENA  0
-#define WM1250_EV1_GPIO_CLK_SEL0 1
-#define WM1250_EV1_GPIO_CLK_SEL1 2
-#define WM1250_EV1_GPIO_OSR      3
-#define WM1250_EV1_GPIO_MASTER   4
-
-
-struct wm1250_ev1_pdata {
-	int gpios[WM1250_EV1_NUM_GPIOS];
-};
-
-#endif
diff --git a/sound/soc/codecs/wm1250-ev1.c b/sound/soc/codecs/wm1250-ev1.c
index d7eeb41ba60f..a2a8b2a4b19b 100644
--- a/sound/soc/codecs/wm1250-ev1.c
+++ b/sound/soc/codecs/wm1250-ev1.c
@@ -9,34 +9,23 @@
 #include <linux/module.h>
 #include <linux/slab.h>
 #include <linux/i2c.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 
 #include <sound/soc.h>
 #include <sound/soc-dapm.h>
-#include <sound/wm1250-ev1.h>
-
-static const char *wm1250_gpio_names[WM1250_EV1_NUM_GPIOS] = {
-	"WM1250 CLK_ENA",
-	"WM1250 CLK_SEL0",
-	"WM1250 CLK_SEL1",
-	"WM1250 OSR",
-	"WM1250 MASTER",
-};
 
 struct wm1250_priv {
-	struct gpio gpios[WM1250_EV1_NUM_GPIOS];
+	struct gpio_desc *clk_ena;
+	struct gpio_desc *clk_sel0;
+	struct gpio_desc *clk_sel1;
+	struct gpio_desc *osr;
+	struct gpio_desc *master;
 };
 
 static int wm1250_ev1_set_bias_level(struct snd_soc_component *component,
 				     enum snd_soc_bias_level level)
 {
 	struct wm1250_priv *wm1250 = dev_get_drvdata(component->dev);
-	int ena;
-
-	if (wm1250)
-		ena = wm1250->gpios[WM1250_EV1_GPIO_CLK_ENA].gpio;
-	else
-		ena = -1;
 
 	switch (level) {
 	case SND_SOC_BIAS_ON:
@@ -46,13 +35,11 @@ static int wm1250_ev1_set_bias_level(struct snd_soc_component *component,
 		break;
 
 	case SND_SOC_BIAS_STANDBY:
-		if (ena >= 0)
-			gpio_set_value_cansleep(ena, 1);
+		gpiod_set_value_cansleep(wm1250->clk_ena, 1);
 		break;
 
 	case SND_SOC_BIAS_OFF:
-		if (ena >= 0)
-			gpio_set_value_cansleep(ena, 0);
+		gpiod_set_value_cansleep(wm1250->clk_ena, 0);
 		break;
 	}
 
@@ -80,28 +67,20 @@ static int wm1250_ev1_hw_params(struct snd_pcm_substream *substream,
 
 	switch (params_rate(params)) {
 	case 8000:
-		gpio_set_value(wm1250->gpios[WM1250_EV1_GPIO_CLK_SEL0].gpio,
-			       1);
-		gpio_set_value(wm1250->gpios[WM1250_EV1_GPIO_CLK_SEL1].gpio,
-			       1);
+		gpiod_set_value(wm1250->clk_sel0, 1);
+		gpiod_set_value(wm1250->clk_sel1, 1);
 		break;
 	case 16000:
-		gpio_set_value(wm1250->gpios[WM1250_EV1_GPIO_CLK_SEL0].gpio,
-			       0);
-		gpio_set_value(wm1250->gpios[WM1250_EV1_GPIO_CLK_SEL1].gpio,
-			       1);
+		gpiod_set_value(wm1250->clk_sel0, 0);
+		gpiod_set_value(wm1250->clk_sel1, 1);
 		break;
 	case 32000:
-		gpio_set_value(wm1250->gpios[WM1250_EV1_GPIO_CLK_SEL0].gpio,
-			       1);
-		gpio_set_value(wm1250->gpios[WM1250_EV1_GPIO_CLK_SEL1].gpio,
-			       0);
+		gpiod_set_value(wm1250->clk_sel0, 1);
+		gpiod_set_value(wm1250->clk_sel1, 0);
 		break;
 	case 64000:
-		gpio_set_value(wm1250->gpios[WM1250_EV1_GPIO_CLK_SEL0].gpio,
-			       0);
-		gpio_set_value(wm1250->gpios[WM1250_EV1_GPIO_CLK_SEL1].gpio,
-			       0);
+		gpiod_set_value(wm1250->clk_sel0, 0);
+		gpiod_set_value(wm1250->clk_sel1, 0);
 		break;
 	default:
 		return -EINVAL;
@@ -150,45 +129,43 @@ static int wm1250_ev1_pdata(struct i2c_client *i2c)
 {
 	struct wm1250_ev1_pdata *pdata = dev_get_platdata(&i2c->dev);
 	struct wm1250_priv *wm1250;
-	int i, ret;
+	int ret;
 
 	if (!pdata)
 		return 0;
 
 	wm1250 = devm_kzalloc(&i2c->dev, sizeof(*wm1250), GFP_KERNEL);
-	if (!wm1250) {
-		ret = -ENOMEM;
-		goto err;
-	}
-
-	for (i = 0; i < ARRAY_SIZE(wm1250->gpios); i++) {
-		wm1250->gpios[i].gpio = pdata->gpios[i];
-		wm1250->gpios[i].label = wm1250_gpio_names[i];
-		wm1250->gpios[i].flags = GPIOF_OUT_INIT_LOW;
-	}
-	wm1250->gpios[WM1250_EV1_GPIO_CLK_SEL0].flags = GPIOF_OUT_INIT_HIGH;
-	wm1250->gpios[WM1250_EV1_GPIO_CLK_SEL1].flags = GPIOF_OUT_INIT_HIGH;
-
-	ret = gpio_request_array(wm1250->gpios, ARRAY_SIZE(wm1250->gpios));
-	if (ret != 0) {
-		dev_err(&i2c->dev, "Failed to get GPIOs: %d\n", ret);
-		goto err;
-	}
+	if (!wm1250)
+		return -ENOMEM;
+
+	wm1250->clk_ena = devm_gpiod_get(&i2c->dev, "clk-ena", GPIOD_OUT_LOW);
+	if (IS_ERR(wm1250->clk_ena))
+		return dev_err_probe(&i2c->dev, PTR_ERR(wm1250->clk_ena),
+				     "failed to get clock enable GPIO\n");
+
+	wm1250->clk_sel0 = devm_gpiod_get(&i2c->dev, "clk-sel0", GPIOD_OUT_HIGH);
+	if (IS_ERR(wm1250->clk_sel0))
+		return dev_err_probe(&i2c->dev, PTR_ERR(wm1250->clk_sel0),
+				     "failed to get clock sel0 GPIO\n");
+
+	wm1250->clk_sel1 = devm_gpiod_get(&i2c->dev, "clk-sel1", GPIOD_OUT_HIGH);
+	if (IS_ERR(wm1250->clk_sel1))
+		return dev_err_probe(&i2c->dev, PTR_ERR(wm1250->clk_sel1),
+				     "failed to get clock sel1 GPIO\n");
+
+	wm1250->osr = devm_gpiod_get(&i2c->dev, "osr", GPIOD_OUT_LOW);
+	if (IS_ERR(wm1250->osr))
+		return dev_err_probe(&i2c->dev, PTR_ERR(wm1250->osr),
+				     "failed to get OSR GPIO\n");
+
+	wm1250->master = devm_gpiod_get(&i2c->dev, "master", GPIOD_OUT_LOW);
+	if (IS_ERR(wm1250->master))
+		return dev_err_probe(&i2c->dev, PTR_ERR(wm1250->master),
+				     "failed to get MASTER GPIO\n");
 
 	dev_set_drvdata(&i2c->dev, wm1250);
 
 	return ret;
-
-err:
-	return ret;
-}
-
-static void wm1250_ev1_free(struct i2c_client *i2c)
-{
-	struct wm1250_priv *wm1250 = dev_get_drvdata(&i2c->dev);
-
-	if (wm1250)
-		gpio_free_array(wm1250->gpios, ARRAY_SIZE(wm1250->gpios));
 }
 
 static int wm1250_ev1_probe(struct i2c_client *i2c)
@@ -221,18 +198,12 @@ static int wm1250_ev1_probe(struct i2c_client *i2c)
 				     &wm1250_ev1_dai, 1);
 	if (ret != 0) {
 		dev_err(&i2c->dev, "Failed to register CODEC: %d\n", ret);
-		wm1250_ev1_free(i2c);
 		return ret;
 	}
 
 	return 0;
 }
 
-static void wm1250_ev1_remove(struct i2c_client *i2c)
-{
-	wm1250_ev1_free(i2c);
-}
-
 static const struct i2c_device_id wm1250_ev1_i2c_id[] = {
 	{ "wm1250-ev1", 0 },
 	{ }
@@ -244,7 +215,6 @@ static struct i2c_driver wm1250_ev1_i2c_driver = {
 		.name = "wm1250-ev1",
 	},
 	.probe =    wm1250_ev1_probe,
-	.remove =   wm1250_ev1_remove,
 	.id_table = wm1250_ev1_i2c_id,
 };
 

-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 3/5] ASoC: wm2200: Convert to GPIO descriptors

[Linus Walleij]

This converts the WM2200 codec to use GPIO descriptors.
This is a pretty straight-forward conversion, and it also
switches over the single in-tree user in the S3C
Cragganmore module for S3C 6410.

This coded does not seem to get selected or be selectable
through Kconfig, I had to hack another soundcard Kconfig
entry to select it for compile tests.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 arch/arm/mach-s3c/mach-crag6410-module.c | 13 ++++++-
 include/sound/wm2200.h                   |  2 -
 sound/soc/codecs/wm2200.c                | 67 ++++++++++++++++----------------
 3 files changed, 44 insertions(+), 38 deletions(-)

diff --git a/arch/arm/mach-s3c/mach-crag6410-module.c b/arch/arm/mach-s3c/mach-crag6410-module.c
index a9a713641047..1df6b7e52c9d 100644
--- a/arch/arm/mach-s3c/mach-crag6410-module.c
+++ b/arch/arm/mach-s3c/mach-crag6410-module.c
@@ -305,12 +305,20 @@ static const struct i2c_board_info wm6230_i2c_devs[] = {
 };
 
 static struct wm2200_pdata wm2200_pdata = {
-	.ldo_ena = S3C64XX_GPN(7),
 	.gpio_defaults = {
 		[2] = 0x0005,  /* GPIO3 24.576MHz output clock */
 	},
 };
 
+static struct gpiod_lookup_table wm2200_gpiod_table = {
+	.dev_id = "1-003a", /* Device 003a on I2C bus 1 */
+	.table = {
+		GPIO_LOOKUP("GPION", 7,
+			    "wlf,ldo1ena", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 static const struct i2c_board_info wm2200_i2c[] = {
 	{ I2C_BOARD_INFO("wm2200", 0x3a),
 	  .platform_data = &wm2200_pdata, },
@@ -372,7 +380,8 @@ static const struct {
 	  .num_spi_devs = ARRAY_SIZE(wm5102_spi_devs),
 	  .gpiod_table = &wm5102_gpiod_table },
 	{ .id = 0x3f, .rev = -1, .name = "WM2200-6271-CS90-M-REV1",
-	  .i2c_devs = wm2200_i2c, .num_i2c_devs = ARRAY_SIZE(wm2200_i2c) },
+	  .i2c_devs = wm2200_i2c, .num_i2c_devs = ARRAY_SIZE(wm2200_i2c),
+	  .gpiod_table = &wm2200_gpiod_table },
 };
 
 static int wlf_gf_module_probe(struct i2c_client *i2c)
diff --git a/include/sound/wm2200.h b/include/sound/wm2200.h
index 9987e6c09bdc..2e4913ee2505 100644
--- a/include/sound/wm2200.h
+++ b/include/sound/wm2200.h
@@ -42,8 +42,6 @@ struct wm2200_micbias {
 };
 
 struct wm2200_pdata {
-	int reset;      /** GPIO controlling /RESET, if any */
-	int ldo_ena;    /** GPIO controlling LODENA, if any */
 	int irq_flags;
 
 	int gpio_defaults[4];
diff --git a/sound/soc/codecs/wm2200.c b/sound/soc/codecs/wm2200.c
index 9679906c6bd5..69c9c2bd7e7b 100644
--- a/sound/soc/codecs/wm2200.c
+++ b/sound/soc/codecs/wm2200.c
@@ -14,7 +14,7 @@
 #include <linux/pm.h>
 #include <linux/firmware.h>
 #include <linux/gcd.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/i2c.h>
 #include <linux/pm_runtime.h>
 #include <linux/regulator/consumer.h>
@@ -79,6 +79,8 @@ struct wm2200_priv {
 	struct snd_soc_component *component;
 	struct wm2200_pdata pdata;
 	struct regulator_bulk_data core_supplies[WM2200_NUM_CORE_SUPPLIES];
+	struct gpio_desc *ldo_ena;
+	struct gpio_desc *reset;
 
 	struct completion fll_lock;
 	int fll_fout;
@@ -975,9 +977,10 @@ static const struct reg_sequence wm2200_reva_patch[] = {
 
 static int wm2200_reset(struct wm2200_priv *wm2200)
 {
-	if (wm2200->pdata.reset) {
-		gpio_set_value_cansleep(wm2200->pdata.reset, 0);
-		gpio_set_value_cansleep(wm2200->pdata.reset, 1);
+	if (wm2200->reset) {
+		/* Descriptor flagged active low, so this will be inverted */
+		gpiod_set_value_cansleep(wm2200->reset, 1);
+		gpiod_set_value_cansleep(wm2200->reset, 0);
 
 		return 0;
 	} else {
@@ -2246,28 +2249,28 @@ static int wm2200_i2c_probe(struct i2c_client *i2c)
 		return ret;
 	}
 
-	if (wm2200->pdata.ldo_ena) {
-		ret = devm_gpio_request_one(&i2c->dev, wm2200->pdata.ldo_ena,
-					    GPIOF_OUT_INIT_HIGH,
-					    "WM2200 LDOENA");
-		if (ret < 0) {
-			dev_err(&i2c->dev, "Failed to request LDOENA %d: %d\n",
-				wm2200->pdata.ldo_ena, ret);
-			goto err_enable;
-		}
+	wm2200->ldo_ena = devm_gpiod_get_optional(&i2c->dev, "wlf,ldo1ena",
+						  GPIOD_OUT_HIGH);
+	if (IS_ERR(wm2200->ldo_ena)) {
+		ret = PTR_ERR(wm2200->ldo_ena);
+		dev_err(&i2c->dev, "Failed to request LDOENA GPIO %d\n",
+			ret);
+		goto err_enable;
+	}
+	if (wm2200->ldo_ena) {
+		gpiod_set_consumer_name(wm2200->ldo_ena, "WM2200 LDOENA");
 		msleep(2);
 	}
 
-	if (wm2200->pdata.reset) {
-		ret = devm_gpio_request_one(&i2c->dev, wm2200->pdata.reset,
-					    GPIOF_OUT_INIT_HIGH,
-					    "WM2200 /RESET");
-		if (ret < 0) {
-			dev_err(&i2c->dev, "Failed to request /RESET %d: %d\n",
-				wm2200->pdata.reset, ret);
-			goto err_ldo;
-		}
+	wm2200->reset = devm_gpiod_get_optional(&i2c->dev, "reset",
+						GPIOD_OUT_LOW);
+	if (IS_ERR(wm2200->reset)) {
+		ret = PTR_ERR(wm2200->reset);
+		dev_err(&i2c->dev, "Failed to request RESET GPIO %d\n",
+			ret);
+		goto err_ldo;
 	}
+	gpiod_set_consumer_name(wm2200->reset, "WM2200 /RESET");
 
 	ret = regmap_read(wm2200->regmap, WM2200_SOFTWARE_RESET, &reg);
 	if (ret < 0) {
@@ -2403,11 +2406,9 @@ static int wm2200_i2c_probe(struct i2c_client *i2c)
 	if (i2c->irq)
 		free_irq(i2c->irq, wm2200);
 err_reset:
-	if (wm2200->pdata.reset)
-		gpio_set_value_cansleep(wm2200->pdata.reset, 0);
+	gpiod_set_value_cansleep(wm2200->reset, 1);
 err_ldo:
-	if (wm2200->pdata.ldo_ena)
-		gpio_set_value_cansleep(wm2200->pdata.ldo_ena, 0);
+	gpiod_set_value_cansleep(wm2200->ldo_ena, 0);
 err_enable:
 	regulator_bulk_disable(ARRAY_SIZE(wm2200->core_supplies),
 			       wm2200->core_supplies);
@@ -2421,10 +2422,9 @@ static void wm2200_i2c_remove(struct i2c_client *i2c)
 	pm_runtime_disable(&i2c->dev);
 	if (i2c->irq)
 		free_irq(i2c->irq, wm2200);
-	if (wm2200->pdata.reset)
-		gpio_set_value_cansleep(wm2200->pdata.reset, 0);
-	if (wm2200->pdata.ldo_ena)
-		gpio_set_value_cansleep(wm2200->pdata.ldo_ena, 0);
+	/* Assert RESET, disable LDO */
+	gpiod_set_value_cansleep(wm2200->reset, 1);
+	gpiod_set_value_cansleep(wm2200->ldo_ena, 0);
 	regulator_bulk_disable(ARRAY_SIZE(wm2200->core_supplies),
 			       wm2200->core_supplies);
 }
@@ -2436,8 +2436,7 @@ static int wm2200_runtime_suspend(struct device *dev)
 
 	regcache_cache_only(wm2200->regmap, true);
 	regcache_mark_dirty(wm2200->regmap);
-	if (wm2200->pdata.ldo_ena)
-		gpio_set_value_cansleep(wm2200->pdata.ldo_ena, 0);
+	gpiod_set_value_cansleep(wm2200->ldo_ena, 0);
 	regulator_bulk_disable(ARRAY_SIZE(wm2200->core_supplies),
 			       wm2200->core_supplies);
 
@@ -2457,8 +2456,8 @@ static int wm2200_runtime_resume(struct device *dev)
 		return ret;
 	}
 
-	if (wm2200->pdata.ldo_ena) {
-		gpio_set_value_cansleep(wm2200->pdata.ldo_ena, 1);
+	if (wm2200->ldo_ena) {
+		gpiod_set_value_cansleep(wm2200->ldo_ena, 1);
 		msleep(2);
 	}
 

-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 4/5] ASoC: wm5100: Convert to GPIO descriptors

[Linus Walleij]

This converts the WM5100 codec to use GPIO descriptors, a pretty
straight-forward conversion with the following peculiarities:

- The driver is instantiating a GPIO chip named wm5100, and the
  headphone polarity detection GPIO is lifted from there. We add
  this to the GPIO descriptor table as well, and we can then get
  rid of also the base address for the GPIO chip from the
  platform data and just use dynamic numbering.

- Fix up the only in-tree user which is the Cragganmore 6410
  module.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 arch/arm/mach-s3c/mach-crag6410-module.c |  17 +++--
 include/sound/wm5100.h                   |   4 --
 sound/soc/codecs/wm5100.c                | 107 +++++++++++--------------------
 3 files changed, 52 insertions(+), 76 deletions(-)

diff --git a/arch/arm/mach-s3c/mach-crag6410-module.c b/arch/arm/mach-s3c/mach-crag6410-module.c
index 1df6b7e52c9d..59456fbebf1b 100644
--- a/arch/arm/mach-s3c/mach-crag6410-module.c
+++ b/arch/arm/mach-s3c/mach-crag6410-module.c
@@ -70,10 +70,19 @@ static struct spi_board_info balblair_devs[] = {
 	},
 };
 
+static struct gpiod_lookup_table wm5100_gpiod_table = {
+	.dev_id = "1-001a", /* Device 001a on I2C bus 1 */
+	.table = {
+		GPIO_LOOKUP("GPION", 7,
+			    "wlf,ldo1ena", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("wm5100", 3,
+			    "hp-pol", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 static struct wm5100_pdata wm5100_pdata = {
-	.ldo_ena = S3C64XX_GPN(7),
 	.irq_flags = IRQF_TRIGGER_HIGH,
-	.gpio_base = CODEC_GPIO_BASE,
 
 	.in_mode = {
 		WM5100_IN_DIFF,
@@ -82,7 +91,6 @@ static struct wm5100_pdata wm5100_pdata = {
 		WM5100_IN_SE,
 	},
 
-	.hp_pol = CODEC_GPIO_BASE + 3,
 	.jack_modes = {
 		{ WM5100_MICDET_MICBIAS3, 0, 0 },
 		{ WM5100_MICDET_MICBIAS2, 1, 1 },
@@ -366,7 +374,8 @@ static const struct {
 	{ .id = 0x3a, .rev = 0xff, .name = "1259-EV1 Tobermory",
 	  .i2c_devs = wm1259_devs, .num_i2c_devs = ARRAY_SIZE(wm1259_devs) },
 	{ .id = 0x3b, .rev = 0xff, .name = "1255-EV1 Kilchoman",
-	  .i2c_devs = wm1255_devs, .num_i2c_devs = ARRAY_SIZE(wm1255_devs) },
+	  .i2c_devs = wm1255_devs, .num_i2c_devs = ARRAY_SIZE(wm1255_devs),
+	  .gpiod_table = &wm5100_gpiod_table },
 	{ .id = 0x3c, .rev = 0xff, .name = "1273-EV1 Longmorn" },
 	{ .id = 0x3d, .rev = 0xff, .name = "1277-EV1 Littlemill",
 	  .i2c_devs = wm1277_devs, .num_i2c_devs = ARRAY_SIZE(wm1277_devs),
diff --git a/include/sound/wm5100.h b/include/sound/wm5100.h
index b94badf72947..1c48090fdb2c 100644
--- a/include/sound/wm5100.h
+++ b/include/sound/wm5100.h
@@ -36,11 +36,7 @@ struct wm5100_jack_mode {
 #define WM5100_GPIO_SET 0x10000
 
 struct wm5100_pdata {
-	int reset;      /** GPIO controlling /RESET, if any */
-	int ldo_ena;    /** GPIO controlling LODENA, if any */
-	int hp_pol;     /** GPIO controlling headset polarity, if any */
 	int irq_flags;
-	int gpio_base;
 
 	struct wm5100_jack_mode jack_modes[2];
 
diff --git a/sound/soc/codecs/wm5100.c b/sound/soc/codecs/wm5100.c
index ff63723928a1..7ee4b45c0834 100644
--- a/sound/soc/codecs/wm5100.c
+++ b/sound/soc/codecs/wm5100.c
@@ -15,7 +15,7 @@
 #include <linux/pm.h>
 #include <linux/gcd.h>
 #include <linux/gpio/driver.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/i2c.h>
 #include <linux/pm_runtime.h>
 #include <linux/regulator/consumer.h>
@@ -55,6 +55,9 @@ struct wm5100_priv {
 	struct snd_soc_component *component;
 
 	struct regulator_bulk_data core_supplies[WM5100_NUM_CORE_SUPPLIES];
+	struct gpio_desc *reset;
+	struct gpio_desc *ldo_ena;
+	struct gpio_desc *hp_pol;
 
 	int rev;
 
@@ -205,9 +208,9 @@ static void wm5100_free_sr(struct snd_soc_component *component, int rate)
 
 static int wm5100_reset(struct wm5100_priv *wm5100)
 {
-	if (wm5100->pdata.reset) {
-		gpio_set_value_cansleep(wm5100->pdata.reset, 0);
-		gpio_set_value_cansleep(wm5100->pdata.reset, 1);
+	if (wm5100->reset) {
+		gpiod_set_value_cansleep(wm5100->reset, 1);
+		gpiod_set_value_cansleep(wm5100->reset, 0);
 
 		return 0;
 	} else {
@@ -1974,7 +1977,7 @@ static void wm5100_set_detect_mode(struct wm5100_priv *wm5100, int the_mode)
 	if (WARN_ON(the_mode >= ARRAY_SIZE(wm5100->pdata.jack_modes)))
 		return;
 
-	gpio_set_value_cansleep(wm5100->pdata.hp_pol, mode->hp_pol);
+	gpiod_set_value_cansleep(wm5100->hp_pol, mode->hp_pol);
 	regmap_update_bits(wm5100->regmap, WM5100_ACCESSORY_DETECT_MODE_1,
 			   WM5100_ACCDET_BIAS_SRC_MASK |
 			   WM5100_ACCDET_SRC,
@@ -2299,11 +2302,7 @@ static void wm5100_init_gpio(struct i2c_client *i2c)
 	wm5100->gpio_chip = wm5100_template_chip;
 	wm5100->gpio_chip.ngpio = 6;
 	wm5100->gpio_chip.parent = &i2c->dev;
-
-	if (wm5100->pdata.gpio_base)
-		wm5100->gpio_chip.base = wm5100->pdata.gpio_base;
-	else
-		wm5100->gpio_chip.base = -1;
+	wm5100->gpio_chip.base = -1;
 
 	ret = gpiochip_add_data(&wm5100->gpio_chip, wm5100);
 	if (ret != 0)
@@ -2349,35 +2348,20 @@ static int wm5100_probe(struct snd_soc_component *component)
 		snd_soc_dapm_new_controls(dapm, wm5100_dapm_widgets_noirq,
 					  ARRAY_SIZE(wm5100_dapm_widgets_noirq));
 
-	if (wm5100->pdata.hp_pol) {
-		ret = gpio_request_one(wm5100->pdata.hp_pol,
-				       GPIOF_OUT_INIT_HIGH, "WM5100 HP_POL");
-		if (ret < 0) {
-			dev_err(&i2c->dev, "Failed to request HP_POL %d: %d\n",
-				wm5100->pdata.hp_pol, ret);
-			goto err_gpio;
-		}
+	wm5100->hp_pol = devm_gpiod_get_optional(&i2c->dev, "hp-pol",
+						 GPIOD_OUT_HIGH);
+	if (IS_ERR(wm5100->hp_pol)) {
+		ret = PTR_ERR(wm5100->hp_pol);
+		dev_err(&i2c->dev, "Failed to request HP_POL GPIO: %d\n",
+			ret);
+		return ret;
 	}
 
 	return 0;
-
-err_gpio:
-
-	return ret;
-}
-
-static void wm5100_remove(struct snd_soc_component *component)
-{
-	struct wm5100_priv *wm5100 = snd_soc_component_get_drvdata(component);
-
-	if (wm5100->pdata.hp_pol) {
-		gpio_free(wm5100->pdata.hp_pol);
-	}
 }
 
 static const struct snd_soc_component_driver soc_component_dev_wm5100 = {
 	.probe			= wm5100_probe,
-	.remove			= wm5100_remove,
 	.set_sysclk		= wm5100_set_sysclk,
 	.set_pll		= wm5100_set_fll,
 	.seq_notifier		= wm5100_seq_notifier,
@@ -2460,26 +2444,26 @@ static int wm5100_i2c_probe(struct i2c_client *i2c)
 		goto err;
 	}
 
-	if (wm5100->pdata.ldo_ena) {
-		ret = gpio_request_one(wm5100->pdata.ldo_ena,
-				       GPIOF_OUT_INIT_HIGH, "WM5100 LDOENA");
-		if (ret < 0) {
-			dev_err(&i2c->dev, "Failed to request LDOENA %d: %d\n",
-				wm5100->pdata.ldo_ena, ret);
-			goto err_enable;
-		}
+	wm5100->ldo_ena = devm_gpiod_get_optional(&i2c->dev, "wlf,ldo1ena",
+						  GPIOD_OUT_HIGH);
+	if (IS_ERR(wm5100->ldo_ena)) {
+		ret = PTR_ERR(wm5100->ldo_ena);
+		dev_err(&i2c->dev, "Failed to request LDOENA GPIO: %d\n", ret);
+		goto err_enable;
+	}
+	if (wm5100->ldo_ena) {
+		gpiod_set_consumer_name(wm5100->ldo_ena, "WM5100 LDOENA");
 		msleep(2);
 	}
 
-	if (wm5100->pdata.reset) {
-		ret = gpio_request_one(wm5100->pdata.reset,
-				       GPIOF_OUT_INIT_HIGH, "WM5100 /RESET");
-		if (ret < 0) {
-			dev_err(&i2c->dev, "Failed to request /RESET %d: %d\n",
-				wm5100->pdata.reset, ret);
-			goto err_ldo;
-		}
+	wm5100->reset = devm_gpiod_get_optional(&i2c->dev, "reset",
+						GPIOD_OUT_LOW);
+	if (IS_ERR(wm5100->reset)) {
+		ret = PTR_ERR(wm5100->reset);
+		dev_err(&i2c->dev, "Failed to request /RESET GPIO: %d\n", ret);
+		goto err_ldo;
 	}
+	gpiod_set_consumer_name(wm5100->reset, "WM5100 /RESET");
 
 	ret = regmap_read(wm5100->regmap, WM5100_SOFTWARE_RESET, &reg);
 	if (ret < 0) {
@@ -2619,15 +2603,9 @@ static int wm5100_i2c_probe(struct i2c_client *i2c)
 	if (i2c->irq)
 		free_irq(i2c->irq, wm5100);
 	wm5100_free_gpio(i2c);
-	if (wm5100->pdata.reset) {
-		gpio_set_value_cansleep(wm5100->pdata.reset, 0);
-		gpio_free(wm5100->pdata.reset);
-	}
+	gpiod_set_value_cansleep(wm5100->reset, 1);
 err_ldo:
-	if (wm5100->pdata.ldo_ena) {
-		gpio_set_value_cansleep(wm5100->pdata.ldo_ena, 0);
-		gpio_free(wm5100->pdata.ldo_ena);
-	}
+	gpiod_set_value_cansleep(wm5100->ldo_ena, 0);
 err_enable:
 	regulator_bulk_disable(ARRAY_SIZE(wm5100->core_supplies),
 			       wm5100->core_supplies);
@@ -2643,14 +2621,8 @@ static void wm5100_i2c_remove(struct i2c_client *i2c)
 	if (i2c->irq)
 		free_irq(i2c->irq, wm5100);
 	wm5100_free_gpio(i2c);
-	if (wm5100->pdata.reset) {
-		gpio_set_value_cansleep(wm5100->pdata.reset, 0);
-		gpio_free(wm5100->pdata.reset);
-	}
-	if (wm5100->pdata.ldo_ena) {
-		gpio_set_value_cansleep(wm5100->pdata.ldo_ena, 0);
-		gpio_free(wm5100->pdata.ldo_ena);
-	}
+	gpiod_set_value_cansleep(wm5100->reset, 1);
+	gpiod_set_value_cansleep(wm5100->ldo_ena, 0);
 }
 
 #ifdef CONFIG_PM
@@ -2660,8 +2632,7 @@ static int wm5100_runtime_suspend(struct device *dev)
 
 	regcache_cache_only(wm5100->regmap, true);
 	regcache_mark_dirty(wm5100->regmap);
-	if (wm5100->pdata.ldo_ena)
-		gpio_set_value_cansleep(wm5100->pdata.ldo_ena, 0);
+	gpiod_set_value_cansleep(wm5100->ldo_ena, 0);
 	regulator_bulk_disable(ARRAY_SIZE(wm5100->core_supplies),
 			       wm5100->core_supplies);
 
@@ -2681,8 +2652,8 @@ static int wm5100_runtime_resume(struct device *dev)
 		return ret;
 	}
 
-	if (wm5100->pdata.ldo_ena) {
-		gpio_set_value_cansleep(wm5100->pdata.ldo_ena, 1);
+	if (wm5100->ldo_ena) {
+		gpiod_set_value_cansleep(wm5100->ldo_ena, 1);
 		msleep(2);
 	}
 

-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 5/5] ASoC: wm8996: Convert to GPIO descriptors

[Linus Walleij]

This converts the WM8996 codec to use GPIO descriptors, an a similar
way to WM5100.

The driver is instantiating a GPIO chip named wm8996, and we get
rid of the base address for the GPIO chip from the platform data and
just use dynamic numbering. Move base and ngpio into the static
gpio_chip template.

Fix up the only in-tree user which is the Cragganmore 6410 module.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 arch/arm/mach-s3c/mach-crag6410-module.c | 14 ++++++--
 include/sound/wm8996.h                   |  3 --
 sound/soc/codecs/wm8996.c                | 58 ++++++++++++++------------------
 3 files changed, 36 insertions(+), 39 deletions(-)

diff --git a/arch/arm/mach-s3c/mach-crag6410-module.c b/arch/arm/mach-s3c/mach-crag6410-module.c
index 59456fbebf1b..2de1a89f6e99 100644
--- a/arch/arm/mach-s3c/mach-crag6410-module.c
+++ b/arch/arm/mach-s3c/mach-crag6410-module.c
@@ -127,9 +127,16 @@ static struct wm8996_retune_mobile_config wm8996_retune[] = {
 	},
 };
 
+static struct gpiod_lookup_table wm8996_gpiod_table = {
+	.dev_id = "1-001a", /* Device 001a on I2C bus 1 */
+	.table = {
+		GPIO_LOOKUP("GPION", 7,
+			    "wlf,ldo1ena", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 static struct wm8996_pdata wm8996_pdata __initdata = {
-	.ldo_ena = S3C64XX_GPN(7),
-	.gpio_base = CODEC_GPIO_BASE,
 	.micdet_def = 1,
 	.inl_mode = WM8996_DIFFERRENTIAL_1,
 	.inr_mode = WM8996_DIFFERRENTIAL_1,
@@ -370,7 +377,8 @@ static const struct {
 	  .spi_devs = balblair_devs,
 	  .num_spi_devs = ARRAY_SIZE(balblair_devs) },
 	{ .id = 0x39, .rev = 0xff, .name = "1254-EV1 Dallas Dhu",
-	  .i2c_devs = wm1254_devs, .num_i2c_devs = ARRAY_SIZE(wm1254_devs) },
+	  .i2c_devs = wm1254_devs, .num_i2c_devs = ARRAY_SIZE(wm1254_devs),
+	  .gpiod_table = &wm8996_gpiod_table },
 	{ .id = 0x3a, .rev = 0xff, .name = "1259-EV1 Tobermory",
 	  .i2c_devs = wm1259_devs, .num_i2c_devs = ARRAY_SIZE(wm1259_devs) },
 	{ .id = 0x3b, .rev = 0xff, .name = "1255-EV1 Kilchoman",
diff --git a/include/sound/wm8996.h b/include/sound/wm8996.h
index 247f9917e33d..342abeef288f 100644
--- a/include/sound/wm8996.h
+++ b/include/sound/wm8996.h
@@ -33,8 +33,6 @@ struct wm8996_retune_mobile_config {
 struct wm8996_pdata {
 	int irq_flags;  /** Set IRQ trigger flags; default active low */
 
-	int ldo_ena;  /** GPIO for LDO1; -1 for none */
-
 	int micdet_def;  /** Default MICDET_SRC/HP1FB_SRC/MICD_BIAS */
 
 	enum wm8996_inmode inl_mode;
@@ -42,7 +40,6 @@ struct wm8996_pdata {
 
 	u32 spkmute_seq;  /** Value for register 0x802 */
 
-	int gpio_base;
 	u32 gpio_default[5];
 
 	int num_retune_mobile_cfgs;
diff --git a/sound/soc/codecs/wm8996.c b/sound/soc/codecs/wm8996.c
index df6195778c57..e738326e33ed 100644
--- a/sound/soc/codecs/wm8996.c
+++ b/sound/soc/codecs/wm8996.c
@@ -14,7 +14,7 @@
 #include <linux/pm.h>
 #include <linux/gcd.h>
 #include <linux/gpio/driver.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/i2c.h>
 #include <linux/regmap.h>
 #include <linux/regulator/consumer.h>
@@ -51,7 +51,7 @@ struct wm8996_priv {
 	struct regmap *regmap;
 	struct snd_soc_component *component;
 
-	int ldo1ena;
+	struct gpio_desc *ldo_ena;
 
 	int sysclk;
 	int sysclk_src;
@@ -1596,9 +1596,9 @@ static int wm8996_set_bias_level(struct snd_soc_component *component,
 				return ret;
 			}
 
-			if (wm8996->pdata.ldo_ena >= 0) {
-				gpio_set_value_cansleep(wm8996->pdata.ldo_ena,
-							1);
+			if (wm8996->ldo_ena) {
+				gpiod_set_value_cansleep(wm8996->ldo_ena,
+							 1);
 				msleep(5);
 			}
 
@@ -1615,8 +1615,8 @@ static int wm8996_set_bias_level(struct snd_soc_component *component,
 
 	case SND_SOC_BIAS_OFF:
 		regcache_cache_only(wm8996->regmap, true);
-		if (wm8996->pdata.ldo_ena >= 0) {
-			gpio_set_value_cansleep(wm8996->pdata.ldo_ena, 0);
+		if (wm8996->ldo_ena) {
+			gpiod_set_value_cansleep(wm8996->ldo_ena, 0);
 			regcache_cache_only(wm8996->regmap, true);
 		}
 		regulator_bulk_disable(ARRAY_SIZE(wm8996->supplies),
@@ -2188,6 +2188,8 @@ static const struct gpio_chip wm8996_template_chip = {
 	.direction_input	= wm8996_gpio_direction_in,
 	.get			= wm8996_gpio_get,
 	.can_sleep		= 1,
+	.ngpio			= 5,
+	.base			= -1,
 };
 
 static void wm8996_init_gpio(struct wm8996_priv *wm8996)
@@ -2195,14 +2197,8 @@ static void wm8996_init_gpio(struct wm8996_priv *wm8996)
 	int ret;
 
 	wm8996->gpio_chip = wm8996_template_chip;
-	wm8996->gpio_chip.ngpio = 5;
 	wm8996->gpio_chip.parent = wm8996->dev;
 
-	if (wm8996->pdata.gpio_base)
-		wm8996->gpio_chip.base = wm8996->pdata.gpio_base;
-	else
-		wm8996->gpio_chip.base = -1;
-
 	ret = gpiochip_add_data(&wm8996->gpio_chip, wm8996);
 	if (ret != 0)
 		dev_err(wm8996->dev, "Failed to add GPIOs: %d\n", ret);
@@ -2771,15 +2767,15 @@ static int wm8996_i2c_probe(struct i2c_client *i2c)
 		memcpy(&wm8996->pdata, dev_get_platdata(&i2c->dev),
 		       sizeof(wm8996->pdata));
 
-	if (wm8996->pdata.ldo_ena > 0) {
-		ret = gpio_request_one(wm8996->pdata.ldo_ena,
-				       GPIOF_OUT_INIT_LOW, "WM8996 ENA");
-		if (ret < 0) {
-			dev_err(&i2c->dev, "Failed to request GPIO %d: %d\n",
-				wm8996->pdata.ldo_ena, ret);
-			goto err;
-		}
+	wm8996->ldo_ena = devm_gpiod_get_optional(&i2c->dev, "wlf,ldo1ena",
+						  GPIOD_OUT_LOW);
+	if (IS_ERR(wm8996->ldo_ena)) {
+		ret = PTR_ERR(wm8996->ldo_ena);
+		dev_err(&i2c->dev, "Failed to request LDO ENA GPIO: %d\n",
+			ret);
+		goto err;
 	}
+	gpiod_set_consumer_name(wm8996->ldo_ena, "WM8996 ENA");
 
 	for (i = 0; i < ARRAY_SIZE(wm8996->supplies); i++)
 		wm8996->supplies[i].supply = wm8996_supply_names[i];
@@ -2814,8 +2810,8 @@ static int wm8996_i2c_probe(struct i2c_client *i2c)
 		goto err_gpio;
 	}
 
-	if (wm8996->pdata.ldo_ena > 0) {
-		gpio_set_value_cansleep(wm8996->pdata.ldo_ena, 1);
+	if (wm8996->ldo_ena) {
+		gpiod_set_value_cansleep(wm8996->ldo_ena, 1);
 		msleep(5);
 	}
 
@@ -2847,8 +2843,8 @@ static int wm8996_i2c_probe(struct i2c_client *i2c)
 	dev_info(&i2c->dev, "revision %c\n",
 		 (reg & WM8996_CHIP_REV_MASK) + 'A');
 
-	if (wm8996->pdata.ldo_ena > 0) {
-		gpio_set_value_cansleep(wm8996->pdata.ldo_ena, 0);
+	if (wm8996->ldo_ena) {
+		gpiod_set_value_cansleep(wm8996->ldo_ena, 0);
 		regcache_cache_only(wm8996->regmap, true);
 	} else {
 		ret = regmap_write(wm8996->regmap, WM8996_SOFTWARE_RESET,
@@ -3054,12 +3050,10 @@ static int wm8996_i2c_probe(struct i2c_client *i2c)
 	wm8996_free_gpio(wm8996);
 err_regmap:
 err_enable:
-	if (wm8996->pdata.ldo_ena > 0)
-		gpio_set_value_cansleep(wm8996->pdata.ldo_ena, 0);
+	if (wm8996->ldo_ena)
+		gpiod_set_value_cansleep(wm8996->ldo_ena, 0);
 	regulator_bulk_disable(ARRAY_SIZE(wm8996->supplies), wm8996->supplies);
 err_gpio:
-	if (wm8996->pdata.ldo_ena > 0)
-		gpio_free(wm8996->pdata.ldo_ena);
 err:
 
 	return ret;
@@ -3070,10 +3064,8 @@ static void wm8996_i2c_remove(struct i2c_client *client)
 	struct wm8996_priv *wm8996 = i2c_get_clientdata(client);
 
 	wm8996_free_gpio(wm8996);
-	if (wm8996->pdata.ldo_ena > 0) {
-		gpio_set_value_cansleep(wm8996->pdata.ldo_ena, 0);
-		gpio_free(wm8996->pdata.ldo_ena);
-	}
+	if (wm8996->ldo_ena)
+		gpiod_set_value_cansleep(wm8996->ldo_ena, 0);
 }
 
 static const struct i2c_device_id wm8996_i2c_id[] = {

-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 1/5] ASoC: wm0010: Convert to GPIO descriptors

[Charles Keepax]

On Fri, Dec 08, 2023 at 11:09:25AM +0100, Linus Walleij wrote:
> This converts the WM0010 codec to use GPIO descriptors.
> It's a pretty straight-forward conversion also switching over
> the single in-tree user in the S3C Cragganmore module
> for S3C 6410.
> 
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---

Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>

Thanks,
Charles

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 2/5] ASoC: wm1250-ev1: Convert to GPIO descriptors

[Charles Keepax]

On Fri, Dec 08, 2023 at 11:09:26AM +0100, Linus Walleij wrote:
> This converts the WM1250-EV1 codec to use GPIO descriptors.
> It turns out that the platform data was only used to pass some
> global GPIO numbers from a board file, so we get rid of this
> and also switch over the single in-tree user in the S3C
> Cragganmore module for S3C 6410.
> 
> The driver obtains two GPIO lines named OSR and master and just
> pull them low, we leave this behaviour as it was.
> 
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---
> +	.table = {
> +		GPIO_LOOKUP("GPION", 12, "clk-ena", GPIO_ACTIVE_HIGH),
> +		GPIO_LOOKUP("GPIOL", 12, "clk-sel0", GPIO_ACTIVE_HIGH),
> +		GPIO_LOOKUP("GPIOL", 13, "clk-sel1", GPIO_ACTIVE_HIGH),
> +		GPIO_LOOKUP("GPIOL", 14, "osr", GPIO_ACTIVE_HIGH),
> +		GPIO_LOOKUP("GPIOL", 8, "master", GPIO_ACTIVE_HIGH),
> +		{ },

For my curiousity, what is the significance of GPION vs GPIOL here?

But looks fine to me:

Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>

Thanks,
Charles

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 3/5] ASoC: wm2200: Convert to GPIO descriptors

[Charles Keepax]

On Fri, Dec 08, 2023 at 11:09:27AM +0100, Linus Walleij wrote:
> This converts the WM2200 codec to use GPIO descriptors.
> This is a pretty straight-forward conversion, and it also
> switches over the single in-tree user in the S3C
> Cragganmore module for S3C 6410.
> 
> This coded does not seem to get selected or be selectable
> through Kconfig, I had to hack another soundcard Kconfig
> entry to select it for compile tests.
> 
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---

Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>

Thanks,
Charles

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 4/5] ASoC: wm5100: Convert to GPIO descriptors

[Charles Keepax]

On Fri, Dec 08, 2023 at 11:09:28AM +0100, Linus Walleij wrote:
> This converts the WM5100 codec to use GPIO descriptors, a pretty
> straight-forward conversion with the following peculiarities:
> 
> - The driver is instantiating a GPIO chip named wm5100, and the
>   headphone polarity detection GPIO is lifted from there. We add
>   this to the GPIO descriptor table as well, and we can then get
>   rid of also the base address for the GPIO chip from the
>   platform data and just use dynamic numbering.
> 
> - Fix up the only in-tree user which is the Cragganmore 6410
>   module.
> 
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---

Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>

Thanks,
Charles

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 2/5] ASoC: wm1250-ev1: Convert to GPIO descriptors

[Charles Keepax]

On Fri, Dec 08, 2023 at 12:42:57PM +0000, Charles Keepax wrote:
> On Fri, Dec 08, 2023 at 11:09:26AM +0100, Linus Walleij wrote:
> > This converts the WM1250-EV1 codec to use GPIO descriptors.
> > It turns out that the platform data was only used to pass some
> > global GPIO numbers from a board file, so we get rid of this
> > and also switch over the single in-tree user in the S3C
> > Cragganmore module for S3C 6410.
> > 
> > The driver obtains two GPIO lines named OSR and master and just
> > pull them low, we leave this behaviour as it was.
> > 
> > Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> > ---
> > +	.table = {
> > +		GPIO_LOOKUP("GPION", 12, "clk-ena", GPIO_ACTIVE_HIGH),
> > +		GPIO_LOOKUP("GPIOL", 12, "clk-sel0", GPIO_ACTIVE_HIGH),
> > +		GPIO_LOOKUP("GPIOL", 13, "clk-sel1", GPIO_ACTIVE_HIGH),
> > +		GPIO_LOOKUP("GPIOL", 14, "osr", GPIO_ACTIVE_HIGH),
> > +		GPIO_LOOKUP("GPIOL", 8, "master", GPIO_ACTIVE_HIGH),
> > +		{ },
> 
> For my curiousity, what is the significance of GPION vs GPIOL here?
> 

oops nvm I see it.

Thanks,
Charles

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 5/5] ASoC: wm8996: Convert to GPIO descriptors

[Charles Keepax]

On Fri, Dec 08, 2023 at 11:09:29AM +0100, Linus Walleij wrote:
> This converts the WM8996 codec to use GPIO descriptors, an a similar
> way to WM5100.
> 
> The driver is instantiating a GPIO chip named wm8996, and we get
> rid of the base address for the GPIO chip from the platform data and
> just use dynamic numbering. Move base and ngpio into the static
> gpio_chip template.
> 
> Fix up the only in-tree user which is the Cragganmore 6410 module.
> 
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---

Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>

Thanks,
Charles

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 1/5] ASoC: wm0010: Convert to GPIO descriptors

[Krzysztof Kozlowski]

On 08/12/2023 11:09, Linus Walleij wrote:
> This converts the WM0010 codec to use GPIO descriptors.
> It's a pretty straight-forward conversion also switching over
> the single in-tree user in the S3C Cragganmore module
> for S3C 6410.
> 
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 2/5] ASoC: wm1250-ev1: Convert to GPIO descriptors

[Krzysztof Kozlowski]

On 08/12/2023 11:09, Linus Walleij wrote:
> This converts the WM1250-EV1 codec to use GPIO descriptors.
> It turns out that the platform data was only used to pass some
> global GPIO numbers from a board file, so we get rid of this
> and also switch over the single in-tree user in the S3C
> Cragganmore module for S3C 6410.
> 
> The driver obtains two GPIO lines named OSR and master and just
> pull them low, we leave this behaviour as it was.
> 
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 3/5] ASoC: wm2200: Convert to GPIO descriptors

[Krzysztof Kozlowski]

On 08/12/2023 11:09, Linus Walleij wrote:
> This converts the WM2200 codec to use GPIO descriptors.
> This is a pretty straight-forward conversion, and it also
> switches over the single in-tree user in the S3C
> Cragganmore module for S3C 6410.
> 
> This coded does not seem to get selected or be selectable
> through Kconfig, I had to hack another soundcard Kconfig
> entry to select it for compile tests.
> 
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 4/5] ASoC: wm5100: Convert to GPIO descriptors

[Krzysztof Kozlowski]

On 08/12/2023 11:09, Linus Walleij wrote:
> This converts the WM5100 codec to use GPIO descriptors, a pretty
> straight-forward conversion with the following peculiarities:
> 
> - The driver is instantiating a GPIO chip named wm5100, and the
>   headphone polarity detection GPIO is lifted from there. We add
>   this to the GPIO descriptor table as well, and we can then get
>   rid of also the base address for the GPIO chip from the
>   platform data and just use dynamic numbering.
> 
> - Fix up the only in-tree user which is the Cragganmore 6410
>   module.
> 
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---
>  arch/arm/mach-s3c/mach-crag6410-module.c |  17 +++--

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 5/5] ASoC: wm8996: Convert to GPIO descriptors

[Krzysztof Kozlowski]

On 08/12/2023 11:09, Linus Walleij wrote:
> This converts the WM8996 codec to use GPIO descriptors, an a similar
> way to WM5100.
> 
> The driver is instantiating a GPIO chip named wm8996, and we get
> rid of the base address for the GPIO chip from the platform data and
> just use dynamic numbering. Move base and ngpio into the static
> gpio_chip template.
> 
> Fix up the only in-tree user which is the Cragganmore 6410 module.
> 
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---
>  arch/arm/mach-s3c/mach-crag6410-module.c | 14 ++++++--

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 0/5] GPIO descriptor cleanup for some Wolfson codecs

[Mark Brown]

On Fri, 08 Dec 2023 11:09:24 +0100, Linus Walleij wrote:
> This converts the remaining Wolfson ASoC codecs to
> use GPIO descriptors.
> 
> These Wolfson codecs are mostly used with different
> Samsung S3C (especially Cragganmore 6410) board files,
> so the in-tree users are fixed up in the process.
> 
> [...]

Applied to

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next

Thanks!

[1/5] ASoC: wm0010: Convert to GPIO descriptors
      commit: b53d47775651aa51bb98cdeb968dedb45699d9a1
[2/5] ASoC: wm1250-ev1: Convert to GPIO descriptors
      commit: 10a366f36e2a2e240d9db6da90e501fa16655282
[3/5] ASoC: wm2200: Convert to GPIO descriptors
      commit: 0119b2a24eb592f967a2849b772887c96617ad80
[4/5] ASoC: wm5100: Convert to GPIO descriptors
      commit: 8563cfe39ba5d00d974df25e310fb61b5b3687e1
[5/5] ASoC: wm8996: Convert to GPIO descriptors
      commit: 729f02ec02ae12e5d8a53171bd37e9de56f33677

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel