[PATCH v2 1/9] omap4: powerdomain: Add supported INACTIVE power state

[santosh.shilimkar@ti.com (Santosh Shilimkar)]

> -----Original Message-----
> From: Paul Walmsley [mailto:paul at pwsan.com]
> Sent: Tuesday, February 08, 2011 7:02 AM
> To: Santosh Shilimkar
> Cc: linux-omap at vger.kernel.org; Kevin Hilman; Benoit Cousson;
> Rajendra Nayak; linux-arm-kernel at lists.infradead.org
> Subject: RE: [PATCH v2 1/9] omap4: powerdomain: Add supported
> INACTIVE power state
>
> On Mon, 7 Feb 2011, Santosh Shilimkar wrote:
>
> > > -----Original Message-----
> > > From: Paul Walmsley [mailto:paul at pwsan.com]
> > > Sent: Monday, February 07, 2011 2:12 AM
> > >
> > > Continuing the discussion here:
> > >
> > >    http://www.mail-archive.com/linux-
> > > omap at vger.kernel.org/msg43509.html
> > >
> > > 1. It appears that the OMAP4 powerdomain ON-ACTIVE state is a
> new
> > > state
> > > for OMAP4, and does not exist as such on previous chips (unless
> the
> > > PRM_VOLTCTRL.AUTO_* bits are all disabled)
> > >
> > Actually it's not new state but more of convention change. ON-
> ACTIVE
> > is like ON in OMAP3.
>
> Hmm, based on our earlier list mails, that seems confusing.  Setting
> an
> OMAP3 powerdomain next-power-state to 'ON' in OMAP3 allows voltage
> domain
> transitions to the SLEEP level.  But setting an OMAP4 powerdomain
> next-power-state to 'ON-ACTIVE' does not allow voltage domain
> transitions to the SLEEP level.  And setting an OMAP4 powerdomain
> next-power-state to 'ON-INACTIVE' does allow voltage domain
> transitions to
> the SLEEP level.  Is that correct?
>
You have point. And you are absolutely correct.

> If that's correct, then OMAP4 ON-ACTIVE is a functionally new
> powerdomain
> next-power-state setting, and OMAP4 ON-INACTIVE is the same state as
> OMAP3
> ON.  Unless there's something obvious that I'm missing?
>
> > > 2. It also appears that the OMAP4 powerdomain ON-INACTIVE state
> > > is equivalent to the OMAP3 powerdomain ON state (again, assuming
> > > that the
> > > PRM_VOLTCTRL.AUTO_SLEEP bit is set on OMAP3).
> > >
> > This is correct.
> >
> > > Could you please comment on whether these statements are true or
> > > false?
> > >
> >
> > Just to summarise my undertsnaing of this here.
> > On OMAP3 too, we had possibility of being in a one of the
> > Two state when programmed to PD ON state.
> > ON-ACTIVE or ON-INACTIVE. The PD status registers just
> > says INACTIVE or ON based on the clodomains states within PD.
>
> Right, but when 'ON' is written into an OMAP3 powerdomain's
> next-power-state bits, voltage domain transitions are allowed.  So
> I'm
> just trying to confirm that OMAP3 ON state is functionally
> equivalent to
> the OMAP4 ON-INACTIVE state, and not functionally equivalent to the
> OMAP4
> ON-ACTIVE state.
>
Yep. This is indeed the case.

> We have to ensure that the core code-internal meaning of the (ON,
> INACTIVE, RET, OFF) states doesn't vary across SoC types.  Otherwise
> "ON"
> on OMAP4 won't mean "ON" on OMAP3, and the goal is for the core code
> to be SoC-independent.
>
Agree.

> One way to do that would be to add a small mapping layer for the
> powerdomain set-next-power-state code to:
>
> - allow programming INACTIVE on OMAP3, by ensuring that, when all
>   powerdomains in a voltage domain are in INACTIVE, that AUTO_SLEEP
>   is set to 1, and then setting the hardware next-power-state to ON;
> and
>
> - allow programming ON on OMAP3, by ensuring that AUTO_SLEEP is set
>   to 0, and setting the hardware next-power-state to ON.
>
> On OMAP4, presumably it wouldn't be needed to mess with the
> AUTO_SLEEP
> bit.
>
> Probably to make that work cleanly, either clockdomains or
> powerdomains
> would need to be associated with voltage domains; and some kind of
> counter
> would need to be implemented in the voltage domains to indicate when
> it is
> appropriate to write to the AUTO_SLEEP bit.
>
Sounds right approach.

Regards,
Santosh