[PATCH v4 1/2] arm: dts: mt7623: Add SD-card and EMMC to bananapi-r2

[matthias.bgg@gmail.com (Matthias Brugger)]

On 08/04/2017 02:19 PM, Matthias Brugger wrote:
> 
> 
> On 08/04/2017 12:14 PM, Sean Wang wrote:
>> On Fri, 2017-08-04 at 11:59 +0800, sean.wang at mediatek.com wrote:
>>> From: Sean Wang <sean.wang@mediatek.com>
>>>
>>> The bananapi-r2 board has an SD-card controller and built-in
>>> EMMC storage so enables those devices in the devicetree. Also
>>> cleanup nodes in alphabetical order in the patch.
>>>
>>
>> Hi, Matthias
>>
>> could your help remove those words "Also cleanup nodes in alphabetical
>> order in the patch." when merging, i was forgetting to do it.
>>
>> or prefer wanting me to resend it again?
> 
> Yes I can do that. No need to resend.
> 

Both patches pushed to v4.13-next/dts32 now

Thanks a lot,
Matthias

> Regards,
> Matthias
> 
>>
>>     Sean
>>
>>> Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
>>> Signed-off-by: Sean Wang <sean.wang@mediatek.com>
>>> ---
>>>   arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts | 37 +++++++++++++++++++++++++++
>>>   1 file changed, 37 insertions(+)
>>>
>>> diff --git a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts 
>>> b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
>>> index 9f3e6dd..444ed93 100644
>>> --- a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
>>> +++ b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
>>> @@ -179,6 +179,32 @@
>>>       status = "okay";
>>>   };
>>> +&mmc0 {
>>> +    pinctrl-names = "default", "state_uhs";
>>> +    pinctrl-0 = <&mmc0_pins_default>;
>>> +    pinctrl-1 = <&mmc0_pins_uhs>;
>>> +    status = "okay";
>>> +    bus-width = <8>;
>>> +    max-frequency = <50000000>;
>>> +    cap-mmc-highspeed;
>>> +    vmmc-supply = <&mt6323_vemc3v3_reg>;
>>> +    vqmmc-supply = <&mt6323_vio18_reg>;
>>> +    non-removable;
>>> +};
>>> +
>>> +&mmc1 {
>>> +    pinctrl-names = "default", "state_uhs";
>>> +    pinctrl-0 = <&mmc1_pins_default>;
>>> +    pinctrl-1 = <&mmc1_pins_uhs>;
>>> +    status = "okay";
>>> +    bus-width = <4>;
>>> +    max-frequency = <50000000>;
>>> +    cap-sd-highspeed;
>>> +    cd-gpios = <&pio 261 0>;
>>> +    vmmc-supply = <&mt6323_vmch_reg>;
>>> +    vqmmc-supply = <&mt6323_vio18_reg>;
>>> +};
>>> +
>>>   &pio {
>>>       cir_pins_a:cir at 0 {
>>>           pins_cir {
>>> @@ -314,6 +340,17 @@
>>>               bias-pull-down;
>>>               drive-strength = <MTK_DRIVE_4mA>;
>>>           };
>>> +
>>> +        pins_wp {
>>> +            pinmux = <MT7623_PIN_29_EINT7_FUNC_MSDC1_WP>;
>>> +            input-enable;
>>> +            bias-pull-up;
>>> +        };
>>> +
>>> +        pins_insert {
>>> +            pinmux = <MT7623_PIN_261_MSDC1_INS_FUNC_GPIO261>;
>>> +            bias-pull-up;
>>> +        };
>>>       };
>>>       mmc1_pins_uhs: mmc1 {
>>
>>