From: moinejf@free.fr (Jean-Francois Moine)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH] mmc: sunxi: Add support to the Allwinner A83T
Date: Sat, 4 Jun 2016 12:01:17 +0200 [thread overview]
Message-ID: <mailman.25.1465034594.1636.linux-arm-kernel@lists.infradead.org> (raw)
The A83T has different clock delays.
The values have been adapted from the Banana Pi M3 driver.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
---
Documentation/devicetree/bindings/mmc/sunxi-mmc.txt | 3 ++-
drivers/mmc/host/sunxi-mmc.c | 12 +++++++++++-
2 files changed, 13 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt
index 4bf41d8..45b8520 100644
--- a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt
+++ b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt
@@ -8,7 +8,8 @@ as the speed of SD standard 3.0.
Absolute maximum transfer rate is 200MB/s
Required properties:
- - compatible : "allwinner,sun4i-a10-mmc" or "allwinner,sun5i-a13-mmc"
+ - compatible : "allwinner,sun4i-a10-mmc", "allwinner,sun5i-a13-mmc",
+ "allwinner,sun8i-a83t-mmc" or "allwinner,sun9i-a80-mmc"
- reg : mmc controller base registers
- clocks : a list with 4 phandle + clock specifier pairs
- clock-names : must contain "ahb", "mmc", "output" and "sample"
diff --git a/drivers/mmc/host/sunxi-mmc.c b/drivers/mmc/host/sunxi-mmc.c
index 7fc8b7a..707e705 100644
--- a/drivers/mmc/host/sunxi-mmc.c
+++ b/drivers/mmc/host/sunxi-mmc.c
@@ -941,6 +941,7 @@ static int sunxi_mmc_card_busy(struct mmc_host *mmc)
static const struct of_device_id sunxi_mmc_of_match[] = {
{ .compatible = "allwinner,sun4i-a10-mmc", },
{ .compatible = "allwinner,sun5i-a13-mmc", },
+ { .compatible = "allwinner,sun8i-a83t-mmc", },
{ .compatible = "allwinner,sun9i-a80-mmc", },
{ /* sentinel */ }
};
@@ -962,10 +963,17 @@ static const struct sunxi_mmc_clk_delay sunxi_mmc_clk_delays[] = {
[SDXC_CLK_25M] = { .output = 180, .sample = 75 },
[SDXC_CLK_50M] = { .output = 90, .sample = 120 },
[SDXC_CLK_50M_DDR] = { .output = 60, .sample = 120 },
- /* Value from A83T "new timing mode". Works but might not be right. */
[SDXC_CLK_50M_DDR_8BIT] = { .output = 90, .sample = 180 },
};
+static const struct sunxi_mmc_clk_delay sun8i_a83t_mmc_clk_delays[] = {
+ [SDXC_CLK_400K] = { .output = 180, .sample = 180 },
+ [SDXC_CLK_25M] = { .output = 180, .sample = 50 },
+ [SDXC_CLK_50M] = { .output = 60, .sample = 50 },
+ [SDXC_CLK_50M_DDR] = { .output = 180, .sample = 90 },
+ [SDXC_CLK_50M_DDR_8BIT] = { .output = 180, .sample = 90 },
+};
+
static const struct sunxi_mmc_clk_delay sun9i_mmc_clk_delays[] = {
[SDXC_CLK_400K] = { .output = 180, .sample = 180 },
[SDXC_CLK_25M] = { .output = 180, .sample = 75 },
@@ -987,6 +995,8 @@ static int sunxi_mmc_resource_request(struct sunxi_mmc_host *host,
if (of_device_is_compatible(np, "allwinner,sun9i-a80-mmc"))
host->clk_delays = sun9i_mmc_clk_delays;
+ else if (of_device_is_compatible(np, "allwinner,sun8i-a83t-mmc"))
+ host->clk_delays = sun8i_a83t_mmc_clk_delays;
else
host->clk_delays = sunxi_mmc_clk_delays;
--
2.8.3
next reply other threads:[~2016-06-04 10:01 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-06-04 10:01 Jean-Francois Moine [this message]
[not found] <20160604100253.7141B2DE7D@muse.csie.ntu.edu.tw>
2016-06-05 12:58 ` [PATCH] mmc: sunxi: Add support to the Allwinner A83T Chen-Yu Tsai
2016-06-06 9:13 ` Jean-Francois Moine
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=mailman.25.1465034594.1636.linux-arm-kernel@lists.infradead.org \
--to=moinejf@free.fr \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).