[PATCH] ARM: mx3: Fix a race condition in mxcmmc

[volker.ernst@txtr.com (Volker Ernst)]

This fixes a race condition regarding interrupt bits in the SDHC
controller driver code.

In case of PIO-transfer it does not clear SDHC-status bit#11/12
in the INT-handler anymore. INT-handler might be called during
an ongoing PIO-data-transfer (with some other INT-flag set) and
PIO-transfer depends on these bits being set to detect the end
of the data-transfer. This also means that at the end of PIO-
transfer that PIO-software has to clear these bits itself.

However in case of DMA-transfer these bits have to be cleared
in the INT-handler, because they are used to generate INTs then.

Works solid, no more problems here, can transfer big files.

Signed-off-by: Volker Ernst <volker.ernst@txtr.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Cc: Andy Green <andy@warmcat.com>
---
 drivers/mmc/host/mxcmmc.c |   13 ++++++++++++-
 1 files changed, 12 insertions(+), 1 deletions(-)

diff --git a/drivers/mmc/host/mxcmmc.c b/drivers/mmc/host/mxcmmc.c
index 2c53024..ec18e3b 100644
--- a/drivers/mmc/host/mxcmmc.c
+++ b/drivers/mmc/host/mxcmmc.c
@@ -489,6 +489,9 @@ static void mxcmci_datawork(struct work_struct *work)
 	struct mxcmci_host *host = container_of(work, struct mxcmci_host,
 						  datawork);
 	int datastat = mxcmci_transfer_data(host);
+
+	writel(STATUS_READ_OP_DONE | STATUS_WRITE_OP_DONE,
+		host->base + MMC_REG_STATUS);
 	mxcmci_finish_data(host, datastat);
 
 	if (host->req->stop) {
@@ -553,7 +556,8 @@ static irqreturn_t mxcmci_irq(int irq, void *devid)
 	u32 stat;
 
 	stat = readl(host->base + MMC_REG_STATUS);
-	writel(stat & ~STATUS_SDIO_INT_ACTIVE, host->base + MMC_REG_STATUS);
+	writel(stat & ~(STATUS_SDIO_INT_ACTIVE | STATUS_DATA_TRANS_DONE |
+			STATUS_WRITE_OP_DONE), host->base + MMC_REG_STATUS);
 
 	dev_dbg(mmc_dev(host->mmc), "%s: 0x%08x\n", __func__, stat);
 
@@ -561,6 +565,13 @@ static irqreturn_t mxcmci_irq(int irq, void *devid)
 	sdio_irq = (stat & STATUS_SDIO_INT_ACTIVE) && host->use_sdio;
 	spin_unlock_irqrestore(&host->lock, flags);
 
+#ifdef HAS_DMA
+	if (mxcmci_use_dma(host) &&
+	    (stat & (STATUS_READ_OP_DONE | STATUS_WRITE_OP_DONE)))
+		writel(STATUS_READ_OP_DONE | STATUS_WRITE_OP_DONE,
+			host->base + MMC_REG_STATUS);
+#endif
+
 	if (sdio_irq) {
 		writel(STATUS_SDIO_INT_ACTIVE, host->base + MMC_REG_STATUS);
 		mmc_signal_sdio_irq(host->mmc);
-- 
1.7.0.3