* [PM8921 MFD V4 1/6] mfd: pm8921: Add PMIC 8921 core driver
2011-03-18 4:21 [PM8921 MFD V4 0/6] pm8921 core and subdevices adharmap
@ 2011-03-18 4:21 ` adharmap
2011-03-22 19:00 ` Abhijeet Dharmapurikar
2011-03-18 4:21 ` [PM8921 MFD V4 2/6] mfd: pm8xxx: Add irq support adharmap
` (4 subsequent siblings)
5 siblings, 1 reply; 10+ messages in thread
From: adharmap @ 2011-03-18 4:21 UTC (permalink / raw)
To: davidb, dwalker
Cc: Abhijeet Dharmapurikar, Samuel Ortiz, Bryan Huntsman,
linux-kernel, linux-arm-msm, linux-arm-msm-owner,
linux-arm-kernel, Mark Brown, Linus Walleij, Thomas Glexiner,
Greg Kroah-Hartman
Add support for the Qualcomm PM8921 PMIC chip. The core driver
will communicate with the PMIC chip via the MSM SSBI bus.
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
---
drivers/mfd/Kconfig | 18 ++++
drivers/mfd/Makefile | 1 +
drivers/mfd/pm8921-core.c | 158 +++++++++++++++++++++++++++++++++++++
include/linux/mfd/pm8xxx/core.h | 71 +++++++++++++++++
include/linux/mfd/pm8xxx/pm8921.h | 27 ++++++
5 files changed, 275 insertions(+), 0 deletions(-)
create mode 100644 drivers/mfd/pm8921-core.c
create mode 100644 include/linux/mfd/pm8xxx/core.h
create mode 100644 include/linux/mfd/pm8xxx/pm8921.h
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index fd01836..c7cb258 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -624,6 +624,24 @@ config MFD_WL1273_CORE
driver connects the radio-wl1273 V4L2 module and the wl1273
audio codec.
+config MFD_PM8XXX
+ tristate
+
+config MFD_PM8921_CORE
+ tristate "Qualcomm PM8921 PMIC chip"
+ depends on MSM_SSBI
+ select MFD_CORE
+ select MFD_PM8XXX
+ help
+ If you say yes to this option, support will be included for the
+ built-in PM8921 PMIC chip.
+
+ This is required if your board has a PM8921 and uses its features,
+ such as: MPPs, GPIOs, regulators, interrupts, and PWM.
+
+ Say M here if you want to include support for PM8921 chip as a module.
+ This will build a module called "pm8921-core".
+
endif # MFD_SUPPORT
menu "Multimedia Capabilities Port drivers"
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index a54e2c7..ec158da 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -83,3 +83,4 @@ obj-$(CONFIG_MFD_TPS6586X) += tps6586x.o
obj-$(CONFIG_MFD_VX855) += vx855.o
obj-$(CONFIG_MFD_WL1273_CORE) += wl1273-core.o
obj-$(CONFIG_MFD_CS5535) += cs5535-mfd.o
+obj-$(CONFIG_MFD_PM8921_CORE) += pm8921-core.o
diff --git a/drivers/mfd/pm8921-core.c b/drivers/mfd/pm8921-core.c
new file mode 100644
index 0000000..a2ecd32
--- /dev/null
+++ b/drivers/mfd/pm8921-core.c
@@ -0,0 +1,158 @@
+/*
+ * Copyright (c) 2011, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#define pr_fmt(fmt) "%s: " fmt, __func__
+
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/msm_ssbi.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/pm8xxx/pm8921.h>
+#include <linux/mfd/pm8xxx/core.h>
+
+#define REG_HWREV 0x002 /* PMIC4 revision */
+#define REG_HWREV_2 0x0E8 /* PMIC4 revision 2 */
+
+struct pm8921 {
+ struct device *dev;
+};
+
+static int pm8921_readb(const struct device *dev, u16 addr, u8 *val)
+{
+ const struct pm8xxx_drvdata *pm8921_drvdata = dev_get_drvdata(dev);
+ const struct pm8921 *pmic = pm8921_drvdata->pm_chip_data;
+
+ return msm_ssbi_read(pmic->dev->parent, addr, val, 1);
+}
+
+static int pm8921_writeb(const struct device *dev, u16 addr, u8 val)
+{
+ const struct pm8xxx_drvdata *pm8921_drvdata = dev_get_drvdata(dev);
+ const struct pm8921 *pmic = pm8921_drvdata->pm_chip_data;
+
+ return msm_ssbi_write(pmic->dev->parent, addr, &val, 1);
+}
+
+static int pm8921_read_buf(const struct device *dev, u16 addr, u8 *buf,
+ int cnt)
+{
+ const struct pm8xxx_drvdata *pm8921_drvdata = dev_get_drvdata(dev);
+ const struct pm8921 *pmic = pm8921_drvdata->pm_chip_data;
+
+ return msm_ssbi_read(pmic->dev->parent, addr, buf, cnt);
+}
+
+static int pm8921_write_buf(const struct device *dev, u16 addr, u8 *buf,
+ int cnt)
+{
+ const struct pm8xxx_drvdata *pm8921_drvdata = dev_get_drvdata(dev);
+ const struct pm8921 *pmic = pm8921_drvdata->pm_chip_data;
+
+ return msm_ssbi_write(pmic->dev->parent, addr, buf, cnt);
+}
+
+static struct pm8xxx_drvdata pm8921_drvdata = {
+ .pmic_readb = pm8921_readb,
+ .pmic_writeb = pm8921_writeb,
+ .pmic_read_buf = pm8921_read_buf,
+ .pmic_write_buf = pm8921_write_buf,
+};
+
+static int __devinit pm8921_probe(struct platform_device *pdev)
+{
+ const struct pm8921_platform_data *pdata = pdev->dev.platform_data;
+ struct pm8921 *pmic;
+ int rc;
+ u8 val;
+
+ if (!pdata) {
+ pr_err("missing platform data\n");
+ return -EINVAL;
+ }
+
+ pmic = kzalloc(sizeof(struct pm8921), GFP_KERNEL);
+ if (!pmic) {
+ pr_err("Cannot alloc pm8921 struct\n");
+ return -ENOMEM;
+ }
+
+ /* Read PMIC chip revision */
+ rc = msm_ssbi_read(pdev->dev.parent, REG_HWREV, &val, sizeof(val));
+ if (rc) {
+ pr_err("Failed to read hw rev reg %d:rc=%d\n", REG_HWREV, rc);
+ goto err_read_rev;
+ }
+ pr_info("PMIC revision 1: %02X\n", val);
+
+ /* Read PMIC chip revision 2 */
+ rc = msm_ssbi_read(pdev->dev.parent, REG_HWREV_2, &val, sizeof(val));
+ if (rc) {
+ pr_err("Failed to read hw rev 2 reg %d:rc=%d\n",
+ REG_HWREV_2, rc);
+ goto err_read_rev;
+ }
+ pr_info("PMIC revision 2: %02X\n", val);
+
+ pmic->dev = &pdev->dev;
+ pm8921_drvdata.pm_chip_data = pmic;
+ platform_set_drvdata(pdev, &pm8921_drvdata);
+
+ return 0;
+
+err_read_rev:
+ kfree(pmic);
+ return rc;
+}
+
+static int __devexit pm8921_remove(struct platform_device *pdev)
+{
+ struct pm8xxx_drvdata *drvdata;
+ struct pm8921 *pmic = NULL;
+
+ drvdata = platform_get_drvdata(pdev);
+ if (drvdata)
+ pmic = drvdata->pm_chip_data;
+ if (pmic)
+ mfd_remove_devices(pmic->dev);
+ platform_set_drvdata(pdev, NULL);
+ kfree(pmic);
+
+ return 0;
+}
+
+static struct platform_driver pm8921_driver = {
+ .probe = pm8921_probe,
+ .remove = __devexit_p(pm8921_remove),
+ .driver = {
+ .name = "pm8921-core",
+ .owner = THIS_MODULE,
+ },
+};
+
+static int __init pm8921_init(void)
+{
+ return platform_driver_register(&pm8921_driver);
+}
+subsys_initcall(pm8921_init);
+
+static void __exit pm8921_exit(void)
+{
+ platform_driver_unregister(&pm8921_driver);
+}
+module_exit(pm8921_exit);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("PMIC 8921 core driver");
+MODULE_VERSION("1.0");
+MODULE_ALIAS("platform:pm8921-core");
diff --git a/include/linux/mfd/pm8xxx/core.h b/include/linux/mfd/pm8xxx/core.h
new file mode 100644
index 0000000..36ccb33
--- /dev/null
+++ b/include/linux/mfd/pm8xxx/core.h
@@ -0,0 +1,71 @@
+/*
+ * Copyright (c) 2011, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+/*
+ * Qualcomm PMIC 8xxx driver header file
+ *
+ */
+
+#ifndef __MFD_PM8XXX_CORE_H
+#define __MFD_PM8XXX_CORE_H
+
+#include <linux/mfd/core.h>
+
+struct pm8xxx_drvdata {
+ int (*pmic_readb) (const struct device *dev, u16 addr, u8 *val);
+ int (*pmic_writeb) (const struct device *dev, u16 addr, u8 val);
+ int (*pmic_read_buf) (const struct device *dev, u16 addr, u8 *buf,
+ int n);
+ int (*pmic_write_buf) (const struct device *dev, u16 addr, u8 *buf,
+ int n);
+ void *pm_chip_data;
+};
+
+static inline int pm8xxx_readb(const struct device *dev, u16 addr, u8 *val)
+{
+ struct pm8xxx_drvdata *dd = dev_get_drvdata(dev);
+
+ if (!dd)
+ return -EINVAL;
+ return dd->pmic_readb(dev, addr, val);
+}
+
+static inline int pm8xxx_writeb(const struct device *dev, u16 addr, u8 val)
+{
+ struct pm8xxx_drvdata *dd = dev_get_drvdata(dev);
+
+ if (!dd)
+ return -EINVAL;
+ return dd->pmic_writeb(dev, addr, val);
+}
+
+static inline int pm8xxx_read_buf(const struct device *dev, u16 addr, u8 *buf,
+ int n)
+{
+ struct pm8xxx_drvdata *dd = dev_get_drvdata(dev);
+
+ if (!dd)
+ return -EINVAL;
+ return dd->pmic_read_buf(dev, addr, buf, n);
+}
+
+static inline int pm8xxx_write_buf(const struct device *dev, u16 addr, u8 *buf,
+ int n)
+{
+ struct pm8xxx_drvdata *dd = dev_get_drvdata(dev);
+
+ if (!dd)
+ return -EINVAL;
+ return dd->pmic_write_buf(dev, addr, buf, n);
+}
+
+#endif
diff --git a/include/linux/mfd/pm8xxx/pm8921.h b/include/linux/mfd/pm8xxx/pm8921.h
new file mode 100644
index 0000000..33fbe9c
--- /dev/null
+++ b/include/linux/mfd/pm8xxx/pm8921.h
@@ -0,0 +1,27 @@
+/*
+ * Copyright (c) 2011, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+/*
+ * Qualcomm PMIC 8921 driver header file
+ *
+ */
+
+#ifndef __MFD_PM8921_H
+#define __MFD_PM8921_H
+
+#include <linux/device.h>
+
+struct pm8921_platform_data {
+ int irq_base;
+};
+
+#endif
--
1.7.1
Sent by an employee of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
^ permalink raw reply related [flat|nested] 10+ messages in thread* Re: [PM8921 MFD V4 1/6] mfd: pm8921: Add PMIC 8921 core driver
2011-03-18 4:21 ` [PM8921 MFD V4 1/6] mfd: pm8921: Add PMIC 8921 core driver adharmap
@ 2011-03-22 19:00 ` Abhijeet Dharmapurikar
0 siblings, 0 replies; 10+ messages in thread
From: Abhijeet Dharmapurikar @ 2011-03-22 19:00 UTC (permalink / raw)
To: davidb, dwalker, Samuel Ortiz, grant.likely
Cc: Bryan Huntsman, linux-kernel, linux-arm-msm, linux-arm-msm-owner,
linux-arm-kernel, Mark Brown, Linus Walleij, Thomas Glexiner,
Greg Kroah-Hartman
Sameul Ortiz,
Can you please review/ack this one?
Abhijeet
adharmap@codeaurora.org wrote:
> Add support for the Qualcomm PM8921 PMIC chip. The core driver
> will communicate with the PMIC chip via the MSM SSBI bus.
>
> Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
> ---
> drivers/mfd/Kconfig | 18 ++++
> drivers/mfd/Makefile | 1 +
> drivers/mfd/pm8921-core.c | 158 +++++++++++++++++++++++++++++++++++++
> include/linux/mfd/pm8xxx/core.h | 71 +++++++++++++++++
> include/linux/mfd/pm8xxx/pm8921.h | 27 ++++++
> 5 files changed, 275 insertions(+), 0 deletions(-)
> create mode 100644 drivers/mfd/pm8921-core.c
> create mode 100644 include/linux/mfd/pm8xxx/core.h
> create mode 100644 include/linux/mfd/pm8xxx/pm8921.h
>
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index fd01836..c7cb258 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -624,6 +624,24 @@ config MFD_WL1273_CORE
> driver connects the radio-wl1273 V4L2 module and the wl1273
> audio codec.
>
> +config MFD_PM8XXX
> + tristate
> +
> +config MFD_PM8921_CORE
> + tristate "Qualcomm PM8921 PMIC chip"
> + depends on MSM_SSBI
> + select MFD_CORE
> + select MFD_PM8XXX
> + help
> + If you say yes to this option, support will be included for the
> + built-in PM8921 PMIC chip.
> +
> + This is required if your board has a PM8921 and uses its features,
> + such as: MPPs, GPIOs, regulators, interrupts, and PWM.
> +
> + Say M here if you want to include support for PM8921 chip as a module.
> + This will build a module called "pm8921-core".
> +
> endif # MFD_SUPPORT
>
> menu "Multimedia Capabilities Port drivers"
> diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
> index a54e2c7..ec158da 100644
> --- a/drivers/mfd/Makefile
> +++ b/drivers/mfd/Makefile
> @@ -83,3 +83,4 @@ obj-$(CONFIG_MFD_TPS6586X) += tps6586x.o
> obj-$(CONFIG_MFD_VX855) += vx855.o
> obj-$(CONFIG_MFD_WL1273_CORE) += wl1273-core.o
> obj-$(CONFIG_MFD_CS5535) += cs5535-mfd.o
> +obj-$(CONFIG_MFD_PM8921_CORE) += pm8921-core.o
> diff --git a/drivers/mfd/pm8921-core.c b/drivers/mfd/pm8921-core.c
> new file mode 100644
> index 0000000..a2ecd32
> --- /dev/null
> +++ b/drivers/mfd/pm8921-core.c
> @@ -0,0 +1,158 @@
> +/*
> + * Copyright (c) 2011, Code Aurora Forum. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#define pr_fmt(fmt) "%s: " fmt, __func__
> +
> +#include <linux/kernel.h>
> +#include <linux/platform_device.h>
> +#include <linux/slab.h>
> +#include <linux/msm_ssbi.h>
> +#include <linux/mfd/core.h>
> +#include <linux/mfd/pm8xxx/pm8921.h>
> +#include <linux/mfd/pm8xxx/core.h>
> +
> +#define REG_HWREV 0x002 /* PMIC4 revision */
> +#define REG_HWREV_2 0x0E8 /* PMIC4 revision 2 */
> +
> +struct pm8921 {
> + struct device *dev;
> +};
> +
> +static int pm8921_readb(const struct device *dev, u16 addr, u8 *val)
> +{
> + const struct pm8xxx_drvdata *pm8921_drvdata = dev_get_drvdata(dev);
> + const struct pm8921 *pmic = pm8921_drvdata->pm_chip_data;
> +
> + return msm_ssbi_read(pmic->dev->parent, addr, val, 1);
> +}
> +
> +static int pm8921_writeb(const struct device *dev, u16 addr, u8 val)
> +{
> + const struct pm8xxx_drvdata *pm8921_drvdata = dev_get_drvdata(dev);
> + const struct pm8921 *pmic = pm8921_drvdata->pm_chip_data;
> +
> + return msm_ssbi_write(pmic->dev->parent, addr, &val, 1);
> +}
> +
> +static int pm8921_read_buf(const struct device *dev, u16 addr, u8 *buf,
> + int cnt)
> +{
> + const struct pm8xxx_drvdata *pm8921_drvdata = dev_get_drvdata(dev);
> + const struct pm8921 *pmic = pm8921_drvdata->pm_chip_data;
> +
> + return msm_ssbi_read(pmic->dev->parent, addr, buf, cnt);
> +}
> +
> +static int pm8921_write_buf(const struct device *dev, u16 addr, u8 *buf,
> + int cnt)
> +{
> + const struct pm8xxx_drvdata *pm8921_drvdata = dev_get_drvdata(dev);
> + const struct pm8921 *pmic = pm8921_drvdata->pm_chip_data;
> +
> + return msm_ssbi_write(pmic->dev->parent, addr, buf, cnt);
> +}
> +
> +static struct pm8xxx_drvdata pm8921_drvdata = {
> + .pmic_readb = pm8921_readb,
> + .pmic_writeb = pm8921_writeb,
> + .pmic_read_buf = pm8921_read_buf,
> + .pmic_write_buf = pm8921_write_buf,
> +};
> +
> +static int __devinit pm8921_probe(struct platform_device *pdev)
> +{
> + const struct pm8921_platform_data *pdata = pdev->dev.platform_data;
> + struct pm8921 *pmic;
> + int rc;
> + u8 val;
> +
> + if (!pdata) {
> + pr_err("missing platform data\n");
> + return -EINVAL;
> + }
> +
> + pmic = kzalloc(sizeof(struct pm8921), GFP_KERNEL);
> + if (!pmic) {
> + pr_err("Cannot alloc pm8921 struct\n");
> + return -ENOMEM;
> + }
> +
> + /* Read PMIC chip revision */
> + rc = msm_ssbi_read(pdev->dev.parent, REG_HWREV, &val, sizeof(val));
> + if (rc) {
> + pr_err("Failed to read hw rev reg %d:rc=%d\n", REG_HWREV, rc);
> + goto err_read_rev;
> + }
> + pr_info("PMIC revision 1: %02X\n", val);
> +
> + /* Read PMIC chip revision 2 */
> + rc = msm_ssbi_read(pdev->dev.parent, REG_HWREV_2, &val, sizeof(val));
> + if (rc) {
> + pr_err("Failed to read hw rev 2 reg %d:rc=%d\n",
> + REG_HWREV_2, rc);
> + goto err_read_rev;
> + }
> + pr_info("PMIC revision 2: %02X\n", val);
> +
> + pmic->dev = &pdev->dev;
> + pm8921_drvdata.pm_chip_data = pmic;
> + platform_set_drvdata(pdev, &pm8921_drvdata);
> +
> + return 0;
> +
> +err_read_rev:
> + kfree(pmic);
> + return rc;
> +}
> +
> +static int __devexit pm8921_remove(struct platform_device *pdev)
> +{
> + struct pm8xxx_drvdata *drvdata;
> + struct pm8921 *pmic = NULL;
> +
> + drvdata = platform_get_drvdata(pdev);
> + if (drvdata)
> + pmic = drvdata->pm_chip_data;
> + if (pmic)
> + mfd_remove_devices(pmic->dev);
> + platform_set_drvdata(pdev, NULL);
> + kfree(pmic);
> +
> + return 0;
> +}
> +
> +static struct platform_driver pm8921_driver = {
> + .probe = pm8921_probe,
> + .remove = __devexit_p(pm8921_remove),
> + .driver = {
> + .name = "pm8921-core",
> + .owner = THIS_MODULE,
> + },
> +};
> +
> +static int __init pm8921_init(void)
> +{
> + return platform_driver_register(&pm8921_driver);
> +}
> +subsys_initcall(pm8921_init);
> +
> +static void __exit pm8921_exit(void)
> +{
> + platform_driver_unregister(&pm8921_driver);
> +}
> +module_exit(pm8921_exit);
> +
> +MODULE_LICENSE("GPL v2");
> +MODULE_DESCRIPTION("PMIC 8921 core driver");
> +MODULE_VERSION("1.0");
> +MODULE_ALIAS("platform:pm8921-core");
> diff --git a/include/linux/mfd/pm8xxx/core.h b/include/linux/mfd/pm8xxx/core.h
> new file mode 100644
> index 0000000..36ccb33
> --- /dev/null
> +++ b/include/linux/mfd/pm8xxx/core.h
> @@ -0,0 +1,71 @@
> +/*
> + * Copyright (c) 2011, Code Aurora Forum. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +/*
> + * Qualcomm PMIC 8xxx driver header file
> + *
> + */
> +
> +#ifndef __MFD_PM8XXX_CORE_H
> +#define __MFD_PM8XXX_CORE_H
> +
> +#include <linux/mfd/core.h>
> +
> +struct pm8xxx_drvdata {
> + int (*pmic_readb) (const struct device *dev, u16 addr, u8 *val);
> + int (*pmic_writeb) (const struct device *dev, u16 addr, u8 val);
> + int (*pmic_read_buf) (const struct device *dev, u16 addr, u8 *buf,
> + int n);
> + int (*pmic_write_buf) (const struct device *dev, u16 addr, u8 *buf,
> + int n);
> + void *pm_chip_data;
> +};
> +
> +static inline int pm8xxx_readb(const struct device *dev, u16 addr, u8 *val)
> +{
> + struct pm8xxx_drvdata *dd = dev_get_drvdata(dev);
> +
> + if (!dd)
> + return -EINVAL;
> + return dd->pmic_readb(dev, addr, val);
> +}
> +
> +static inline int pm8xxx_writeb(const struct device *dev, u16 addr, u8 val)
> +{
> + struct pm8xxx_drvdata *dd = dev_get_drvdata(dev);
> +
> + if (!dd)
> + return -EINVAL;
> + return dd->pmic_writeb(dev, addr, val);
> +}
> +
> +static inline int pm8xxx_read_buf(const struct device *dev, u16 addr, u8 *buf,
> + int n)
> +{
> + struct pm8xxx_drvdata *dd = dev_get_drvdata(dev);
> +
> + if (!dd)
> + return -EINVAL;
> + return dd->pmic_read_buf(dev, addr, buf, n);
> +}
> +
> +static inline int pm8xxx_write_buf(const struct device *dev, u16 addr, u8 *buf,
> + int n)
> +{
> + struct pm8xxx_drvdata *dd = dev_get_drvdata(dev);
> +
> + if (!dd)
> + return -EINVAL;
> + return dd->pmic_write_buf(dev, addr, buf, n);
> +}
> +
> +#endif
> diff --git a/include/linux/mfd/pm8xxx/pm8921.h b/include/linux/mfd/pm8xxx/pm8921.h
> new file mode 100644
> index 0000000..33fbe9c
> --- /dev/null
> +++ b/include/linux/mfd/pm8xxx/pm8921.h
> @@ -0,0 +1,27 @@
> +/*
> + * Copyright (c) 2011, Code Aurora Forum. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +/*
> + * Qualcomm PMIC 8921 driver header file
> + *
> + */
> +
> +#ifndef __MFD_PM8921_H
> +#define __MFD_PM8921_H
> +
> +#include <linux/device.h>
> +
> +struct pm8921_platform_data {
> + int irq_base;
> +};
> +
> +#endif
--
--
Sent by an employee of the Qualcomm Innovation Center, Inc. The Qualcomm
Innovation Center, Inc. is a member of the Code Aurora Forum.
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PM8921 MFD V4 2/6] mfd: pm8xxx: Add irq support
2011-03-18 4:21 [PM8921 MFD V4 0/6] pm8921 core and subdevices adharmap
2011-03-18 4:21 ` [PM8921 MFD V4 1/6] mfd: pm8921: Add PMIC 8921 core driver adharmap
@ 2011-03-18 4:21 ` adharmap
2011-03-18 8:38 ` Thomas Gleixner
2011-03-18 4:21 ` [PM8921 MFD V4 3/6] gpio: pm8xxx-gpio: Add pm8xxx gpio driver adharmap
` (3 subsequent siblings)
5 siblings, 1 reply; 10+ messages in thread
From: adharmap @ 2011-03-18 4:21 UTC (permalink / raw)
To: davidb, dwalker
Cc: Abhijeet Dharmapurikar, Samuel Ortiz, Bryan Huntsman,
linux-kernel, linux-arm-msm, linux-arm-msm-owner,
linux-arm-kernel, Mark Brown, Linus Walleij, Thomas Glexiner,
Greg Kroah-Hartman
Add support for the irq controller in Qualcomm 8xxx pmic. The 8xxx
interrupt controller provides control for gpio and mpp configured as
interrupts in addition to other subdevice interrupts. The interrupt
controller also provides a way to read the real time status of an
interrupt. This real time status is the only way one can get the
input values of gpio and mpp lines.
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
---
drivers/mfd/Kconfig | 10 +
drivers/mfd/Makefile | 1 +
drivers/mfd/pm8921-core.c | 54 ++++++
drivers/mfd/pm8xxx-irq.c | 364 +++++++++++++++++++++++++++++++++++++
include/linux/mfd/pm8xxx/core.h | 10 +
include/linux/mfd/pm8xxx/irq.h | 59 ++++++
include/linux/mfd/pm8xxx/pm8921.h | 4 +
7 files changed, 502 insertions(+), 0 deletions(-)
create mode 100644 drivers/mfd/pm8xxx-irq.c
create mode 100644 include/linux/mfd/pm8xxx/irq.h
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index c7cb258..19e758e 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -642,6 +642,16 @@ config MFD_PM8921_CORE
Say M here if you want to include support for PM8921 chip as a module.
This will build a module called "pm8921-core".
+config MFD_PM8XXX_IRQ
+ bool "Support for Qualcomm PM8xxx IRQ features"
+ depends on MFD_PM8XXX
+ default y if MFD_PM8XXX
+ help
+ This is the IRQ driver for Qualcomm PM 8xxx PMIC chips.
+
+ This is required to use certain other PM 8xxx features, such as GPIO
+ and MPP.
+
endif # MFD_SUPPORT
menu "Multimedia Capabilities Port drivers"
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index ec158da..5fc9315 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -84,3 +84,4 @@ obj-$(CONFIG_MFD_VX855) += vx855.o
obj-$(CONFIG_MFD_WL1273_CORE) += wl1273-core.o
obj-$(CONFIG_MFD_CS5535) += cs5535-mfd.o
obj-$(CONFIG_MFD_PM8921_CORE) += pm8921-core.o
+obj-$(CONFIG_MFD_PM8XXX_IRQ) += pm8xxx-irq.o
diff --git a/drivers/mfd/pm8921-core.c b/drivers/mfd/pm8921-core.c
index a2ecd32..e873b15 100644
--- a/drivers/mfd/pm8921-core.c
+++ b/drivers/mfd/pm8921-core.c
@@ -16,6 +16,7 @@
#include <linux/kernel.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
+#include <linux/err.h>
#include <linux/msm_ssbi.h>
#include <linux/mfd/core.h>
#include <linux/mfd/pm8xxx/pm8921.h>
@@ -26,6 +27,7 @@
struct pm8921 {
struct device *dev;
+ struct pm_irq_chip *irq_chip;
};
static int pm8921_readb(const struct device *dev, u16 addr, u8 *val)
@@ -62,19 +64,53 @@ static int pm8921_write_buf(const struct device *dev, u16 addr, u8 *buf,
return msm_ssbi_write(pmic->dev->parent, addr, buf, cnt);
}
+static int pm8921_read_irq_stat(const struct device *dev, int irq)
+{
+ const struct pm8xxx_drvdata *pm8921_drvdata = dev_get_drvdata(dev);
+ const struct pm8921 *pmic = pm8921_drvdata->pm_chip_data;
+
+ return pm8xxx_get_irq_stat(pmic->irq_chip, irq);
+}
+
static struct pm8xxx_drvdata pm8921_drvdata = {
.pmic_readb = pm8921_readb,
.pmic_writeb = pm8921_writeb,
.pmic_read_buf = pm8921_read_buf,
.pmic_write_buf = pm8921_write_buf,
+ .pmic_read_irq_stat = pm8921_read_irq_stat,
};
+static int __devinit pm8921_add_subdevices(const struct pm8921_platform_data
+ *pdata,
+ struct pm8921 *pmic,
+ u32 rev)
+{
+ int ret = 0, irq_base = 0;
+ struct pm_irq_chip *irq_chip;
+
+ if (pdata->irq_pdata) {
+ pdata->irq_pdata->irq_cdata.nirqs = PM8921_NR_IRQS;
+ pdata->irq_pdata->irq_cdata.rev = rev;
+ irq_base = pdata->irq_pdata->irq_base;
+ irq_chip = pm8xxx_irq_init(pmic->dev, pdata->irq_pdata);
+
+ if (IS_ERR(irq_chip)) {
+ pr_err("Failed to init interrupts ret=%ld\n",
+ PTR_ERR(irq_chip));
+ return PTR_ERR(irq_chip);
+ }
+ pmic->irq_chip = irq_chip;
+ }
+ return ret;
+}
+
static int __devinit pm8921_probe(struct platform_device *pdev)
{
const struct pm8921_platform_data *pdata = pdev->dev.platform_data;
struct pm8921 *pmic;
int rc;
u8 val;
+ u32 rev;
if (!pdata) {
pr_err("missing platform data\n");
@@ -94,6 +130,7 @@ static int __devinit pm8921_probe(struct platform_device *pdev)
goto err_read_rev;
}
pr_info("PMIC revision 1: %02X\n", val);
+ rev = val;
/* Read PMIC chip revision 2 */
rc = msm_ssbi_read(pdev->dev.parent, REG_HWREV_2, &val, sizeof(val));
@@ -103,13 +140,26 @@ static int __devinit pm8921_probe(struct platform_device *pdev)
goto err_read_rev;
}
pr_info("PMIC revision 2: %02X\n", val);
+ rev |= val << BITS_PER_BYTE;
pmic->dev = &pdev->dev;
pm8921_drvdata.pm_chip_data = pmic;
platform_set_drvdata(pdev, &pm8921_drvdata);
+ rc = pm8921_add_subdevices(pdata, pmic, rev);
+ if (rc) {
+ pr_err("Cannot add subdevices rc=%d\n", rc);
+ goto err;
+ }
+
+ /* gpio might not work if no irq device is found */
+ WARN_ON(pmic->irq_chip == NULL);
+
return 0;
+err:
+ mfd_remove_devices(pmic->dev);
+ platform_set_drvdata(pdev, NULL);
err_read_rev:
kfree(pmic);
return rc;
@@ -125,6 +175,10 @@ static int __devexit pm8921_remove(struct platform_device *pdev)
pmic = drvdata->pm_chip_data;
if (pmic)
mfd_remove_devices(pmic->dev);
+ if (pmic->irq_chip) {
+ pm8xxx_irq_exit(pmic->irq_chip);
+ pmic->irq_chip = NULL;
+ }
platform_set_drvdata(pdev, NULL);
kfree(pmic);
diff --git a/drivers/mfd/pm8xxx-irq.c b/drivers/mfd/pm8xxx-irq.c
new file mode 100644
index 0000000..613106a
--- /dev/null
+++ b/drivers/mfd/pm8xxx-irq.c
@@ -0,0 +1,364 @@
+/*
+ * Copyright (c) 2011, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#define pr_fmt(fmt) "%s: " fmt, __func__
+
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/kernel.h>
+#include <linux/mfd/pm8xxx/core.h>
+#include <linux/mfd/pm8xxx/irq.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+/* PMIC8xxx IRQ */
+
+#define SSBI_REG_ADDR_IRQ_BASE 0x1BB
+
+#define SSBI_REG_ADDR_IRQ_ROOT (SSBI_REG_ADDR_IRQ_BASE + 0)
+#define SSBI_REG_ADDR_IRQ_M_STATUS1 (SSBI_REG_ADDR_IRQ_BASE + 1)
+#define SSBI_REG_ADDR_IRQ_M_STATUS2 (SSBI_REG_ADDR_IRQ_BASE + 2)
+#define SSBI_REG_ADDR_IRQ_M_STATUS3 (SSBI_REG_ADDR_IRQ_BASE + 3)
+#define SSBI_REG_ADDR_IRQ_M_STATUS4 (SSBI_REG_ADDR_IRQ_BASE + 4)
+#define SSBI_REG_ADDR_IRQ_BLK_SEL (SSBI_REG_ADDR_IRQ_BASE + 5)
+#define SSBI_REG_ADDR_IRQ_IT_STATUS (SSBI_REG_ADDR_IRQ_BASE + 6)
+#define SSBI_REG_ADDR_IRQ_CONFIG (SSBI_REG_ADDR_IRQ_BASE + 7)
+#define SSBI_REG_ADDR_IRQ_RT_STATUS (SSBI_REG_ADDR_IRQ_BASE + 8)
+
+#define PM_IRQF_LVL_SEL 0x01 /* level select */
+#define PM_IRQF_MASK_FE 0x02 /* mask falling edge */
+#define PM_IRQF_MASK_RE 0x04 /* mask rising edge */
+#define PM_IRQF_CLR 0x08 /* clear interrupt */
+#define PM_IRQF_BITS_MASK 0x70
+#define PM_IRQF_BITS_SHIFT 4
+#define PM_IRQF_WRITE 0x80
+
+#define PM_IRQF_MASK_ALL (PM_IRQF_MASK_FE | \
+ PM_IRQF_MASK_RE)
+
+struct pm_irq_chip {
+ struct device *dev;
+ spinlock_t pm_irq_lock;
+ unsigned int devirq;
+ unsigned int irq_base;
+ unsigned int num_irqs;
+ unsigned int num_blocks;
+ unsigned int num_masters;
+ u8 config[0];
+};
+
+static int pm8xxx_read_root_irq(const struct pm_irq_chip *chip, u8 *rp)
+{
+ return pm8xxx_readb(chip->dev, SSBI_REG_ADDR_IRQ_ROOT, rp);
+}
+
+static int pm8xxx_read_master_irq(const struct pm_irq_chip *chip, u8 m, u8 *bp)
+{
+ return pm8xxx_readb(chip->dev,
+ SSBI_REG_ADDR_IRQ_M_STATUS1 + m, bp);
+}
+
+static int pm8xxx_read_block_irq(struct pm_irq_chip *chip, u8 bp, u8 *ip)
+{
+ int rc;
+
+ spin_lock(&chip->pm_irq_lock);
+ rc = pm8xxx_writeb(chip->dev, SSBI_REG_ADDR_IRQ_BLK_SEL, bp);
+ if (rc) {
+ pr_err("Failed Selecting Block %d rc=%d\n", bp, rc);
+ goto bail;
+ }
+
+ rc = pm8xxx_readb(chip->dev, SSBI_REG_ADDR_IRQ_IT_STATUS, ip);
+ if (rc)
+ pr_err("Failed Reading Status rc=%d\n", rc);
+bail:
+ spin_unlock(&chip->pm_irq_lock);
+ return rc;
+}
+
+static int pm8xxx_config_irq(struct pm_irq_chip *chip, u8 bp, u8 cp)
+{
+ int rc;
+
+ spin_lock(&chip->pm_irq_lock);
+ rc = pm8xxx_writeb(chip->dev, SSBI_REG_ADDR_IRQ_BLK_SEL, bp);
+ if (rc) {
+ pr_err("Failed Selecting Block %d rc=%d\n", bp, rc);
+ goto bail;
+ }
+
+ cp |= PM_IRQF_WRITE;
+ rc = pm8xxx_writeb(chip->dev, SSBI_REG_ADDR_IRQ_CONFIG, cp);
+ if (rc)
+ pr_err("Failed Configuring IRQ rc=%d\n", rc);
+bail:
+ spin_unlock(&chip->pm_irq_lock);
+ return rc;
+}
+
+static int pm8xxx_irq_block_handler(struct pm_irq_chip *chip, int block)
+{
+ int pmirq, irq, i, ret = 0;
+ u8 bits;
+
+ ret = pm8xxx_read_block_irq(chip, block, &bits);
+ if (ret) {
+ pr_err("Failed reading %d block ret=%d", block, ret);
+ return ret;
+ }
+ if (!bits) {
+ pr_err("block bit set in master but no irqs: %d", block);
+ return 0;
+ }
+
+ /* Check IRQ bits */
+ for (i = 0; i < 8; i++) {
+ if (bits & (1 << i)) {
+ pmirq = block * 8 + i;
+ irq = pmirq + chip->irq_base;
+ generic_handle_irq(irq);
+ }
+ }
+ return 0;
+}
+
+static int pm8xxx_irq_master_handler(struct pm_irq_chip *chip, int master)
+{
+ u8 blockbits;
+ int block_number, i, ret = 0;
+
+ ret = pm8xxx_read_master_irq(chip, master, &blockbits);
+ if (ret) {
+ pr_err("Failed to read master %d ret=%d\n", master, ret);
+ return ret;
+ }
+ if (!blockbits) {
+ pr_err("master bit set in root but no blocks: %d", master);
+ return 0;
+ }
+
+ for (i = 0; i < 8; i++)
+ if (blockbits & (1 << i)) {
+ block_number = master * 8 + i; /* block # */
+ ret |= pm8xxx_irq_block_handler(chip, block_number);
+ }
+ return ret;
+}
+
+static void pm8xxx_irq_handler(unsigned int irq, struct irq_desc *desc)
+{
+ struct pm_irq_chip *chip = get_irq_desc_data(desc);
+ struct irq_chip *irq_chip = get_irq_desc_chip(desc);
+ u8 root;
+ int i, ret, masters = 0;
+
+ ret = pm8xxx_read_root_irq(chip, &root);
+ if (ret) {
+ pr_err("Can't read root status ret=%d\n", ret);
+ return;
+ }
+
+ /* on pm8xxx series masters start from bit 1 of the root */
+ masters = root >> 1;
+
+ /* Read allowed masters for blocks. */
+ for (i = 0; i < chip->num_masters; i++)
+ if (masters & (1 << i))
+ pm8xxx_irq_master_handler(chip, i);
+
+ irq_chip->irq_ack(&desc->irq_data);
+}
+
+static void pm8xxx_irq_mask_ack(struct irq_data *d)
+{
+ struct pm_irq_chip *chip = irq_data_get_irq_chip_data(d);
+ unsigned int pmirq = d->irq - chip->irq_base;
+ int master, irq_bit;
+ u8 block, config;
+
+ block = pmirq / 8;
+ master = block / 8;
+ irq_bit = pmirq % 8;
+
+ config = chip->config[pmirq] | PM_IRQF_MASK_ALL | PM_IRQF_CLR;
+ pm8xxx_config_irq(chip, block, config);
+}
+
+static void pm8xxx_irq_unmask(struct irq_data *d)
+{
+ struct pm_irq_chip *chip = irq_data_get_irq_chip_data(d);
+ unsigned int pmirq = d->irq - chip->irq_base;
+ int master, irq_bit;
+ u8 block, config;
+
+ block = pmirq / 8;
+ master = block / 8;
+ irq_bit = pmirq % 8;
+
+ config = chip->config[pmirq];
+ pm8xxx_config_irq(chip, block, config);
+}
+
+static int pm8xxx_irq_set_type(struct irq_data *d, unsigned int flow_type)
+{
+ struct pm_irq_chip *chip = irq_data_get_irq_chip_data(d);
+ unsigned int pmirq = d->irq - chip->irq_base;
+ int master, irq_bit;
+ u8 block, config;
+
+ block = pmirq / 8;
+ master = block / 8;
+ irq_bit = pmirq % 8;
+
+ chip->config[pmirq] = (irq_bit << PM_IRQF_BITS_SHIFT)
+ | PM_IRQF_MASK_ALL;
+ if (flow_type & (IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING)) {
+ if (flow_type & IRQF_TRIGGER_RISING)
+ chip->config[pmirq] &= ~PM_IRQF_MASK_RE;
+ if (flow_type & IRQF_TRIGGER_FALLING)
+ chip->config[pmirq] &= ~PM_IRQF_MASK_FE;
+ } else {
+ chip->config[pmirq] |= PM_IRQF_LVL_SEL;
+
+ if (flow_type & IRQF_TRIGGER_HIGH)
+ chip->config[pmirq] &= ~PM_IRQF_MASK_RE;
+ else
+ chip->config[pmirq] &= ~PM_IRQF_MASK_FE;
+ }
+
+ config = chip->config[pmirq] | PM_IRQF_CLR;
+ return pm8xxx_config_irq(chip, block, config);
+}
+
+static struct irq_chip pm8xxx_irq_chip = {
+ .name = "pm8xxx",
+ .irq_mask_ack = pm8xxx_irq_mask_ack,
+ .irq_unmask = pm8xxx_irq_unmask,
+ .irq_set_type = pm8xxx_irq_set_type,
+ .flags = IRQCHIP_MASK_ON_SUSPEND,
+};
+
+/**
+ * pm8xxx_get_irq_stat - get the status of the irq line
+ * @chip: pointer to identify a pmic irq controller
+ * @irq: the irq number
+ *
+ * The pm8xxx gpio and mpp rely on the interrupt block to read
+ * the values on their pins. This function is to facilitate reading
+ * the status of a gpio or an mpp line. The caller has to convert the
+ * gpio number to irq number.
+ *
+ * RETURNS:
+ * an int indicating the value read on that line
+ */
+int pm8xxx_get_irq_stat(struct pm_irq_chip *chip, int irq)
+{
+ int pmirq, rc;
+ u8 block, bits, bit;
+ unsigned long flags;
+
+ if (chip == NULL || irq < chip->irq_base ||
+ irq >= chip->irq_base + chip->num_irqs)
+ return -EINVAL;
+
+ pmirq = irq - chip->irq_base;
+
+ block = pmirq / 8;
+ bit = pmirq % 8;
+
+ spin_lock_irqsave(&chip->pm_irq_lock, flags);
+
+ rc = pm8xxx_writeb(chip->dev, SSBI_REG_ADDR_IRQ_BLK_SEL, block);
+ if (rc) {
+ pr_err("Failed Selecting block irq=%d pmirq=%d blk=%d rc=%d\n",
+ irq, pmirq, block, rc);
+ goto bail_out;
+ }
+
+ rc = pm8xxx_readb(chip->dev, SSBI_REG_ADDR_IRQ_RT_STATUS, &bits);
+ if (rc) {
+ pr_err("Failed Configuring irq=%d pmirq=%d blk=%d rc=%d\n",
+ irq, pmirq, block, rc);
+ goto bail_out;
+ }
+
+ rc = (bits & (1 << bit)) ? 1 : 0;
+
+bail_out:
+ spin_unlock_irqrestore(&chip->pm_irq_lock, flags);
+
+ return rc;
+}
+EXPORT_SYMBOL_GPL(pm8xxx_get_irq_stat);
+
+struct pm_irq_chip * __devinit pm8xxx_irq_init(struct device *dev,
+ const struct pm8xxx_irq_platform_data *pdata)
+{
+ struct pm_irq_chip *chip;
+ int devirq, rc;
+ unsigned int pmirq;
+
+ if (!pdata) {
+ pr_err("No platform data\n");
+ return ERR_PTR(-EINVAL);
+ }
+
+ devirq = pdata->devirq;
+ if (devirq < 0) {
+ pr_err("missing devirq\n");
+ rc = devirq;
+ return ERR_PTR(-EINVAL);
+ }
+
+ chip = kzalloc(sizeof(struct pm_irq_chip)
+ + sizeof(u8) * pdata->irq_cdata.nirqs, GFP_KERNEL);
+ if (!chip) {
+ pr_err("Cannot alloc pm_irq_chip struct\n");
+ return ERR_PTR(-EINVAL);
+ }
+
+ chip->dev = dev;
+ chip->devirq = devirq;
+ chip->irq_base = pdata->irq_base;
+ chip->num_irqs = pdata->irq_cdata.nirqs;
+ chip->num_blocks = DIV_ROUND_UP(chip->num_irqs, 8);
+ chip->num_masters = DIV_ROUND_UP(chip->num_blocks, 8);
+ spin_lock_init(&chip->pm_irq_lock);
+
+ for (pmirq = 0; pmirq < chip->num_irqs; pmirq++) {
+ set_irq_chip(chip->irq_base + pmirq, &pm8xxx_irq_chip);
+ set_irq_chip_data(chip->irq_base + pmirq, chip);
+ set_irq_handler(chip->irq_base + pmirq, handle_level_irq);
+#ifdef CONFIG_ARM
+ set_irq_flags(chip->irq_base + pmirq, IRQF_VALID);
+#else
+ set_irq_noprobe(chip->irq_base + pmirq);
+#endif
+ }
+
+ set_irq_type(devirq, pdata->irq_trigger_flag);
+ set_irq_data(devirq, chip);
+ set_irq_chained_handler(devirq, pm8xxx_irq_handler);
+ set_irq_wake(devirq, 1);
+
+ return chip;
+}
+
+int __devexit pm8xxx_irq_exit(struct pm_irq_chip *chip)
+{
+ set_irq_chained_handler(chip->devirq, NULL);
+ kfree(chip);
+ return 0;
+}
diff --git a/include/linux/mfd/pm8xxx/core.h b/include/linux/mfd/pm8xxx/core.h
index 36ccb33..bd2f4f6 100644
--- a/include/linux/mfd/pm8xxx/core.h
+++ b/include/linux/mfd/pm8xxx/core.h
@@ -27,6 +27,7 @@ struct pm8xxx_drvdata {
int n);
int (*pmic_write_buf) (const struct device *dev, u16 addr, u8 *buf,
int n);
+ int (*pmic_read_irq_stat) (const struct device *dev, int irq);
void *pm_chip_data;
};
@@ -68,4 +69,13 @@ static inline int pm8xxx_write_buf(const struct device *dev, u16 addr, u8 *buf,
return dd->pmic_write_buf(dev, addr, buf, n);
}
+static inline int pm8xxx_read_irq_stat(const struct device *dev, int irq)
+{
+ struct pm8xxx_drvdata *dd = dev_get_drvdata(dev);
+
+ if (!dd)
+ return -EINVAL;
+ return dd->pmic_read_irq_stat(dev, irq);
+}
+
#endif
diff --git a/include/linux/mfd/pm8xxx/irq.h b/include/linux/mfd/pm8xxx/irq.h
new file mode 100644
index 0000000..4b21769
--- /dev/null
+++ b/include/linux/mfd/pm8xxx/irq.h
@@ -0,0 +1,59 @@
+/*
+ * Copyright (c) 2011, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+/*
+ * Qualcomm PMIC irq 8xxx driver header file
+ *
+ */
+
+#ifndef __MFD_PM8XXX_IRQ_H
+#define __MFD_PM8XXX_IRQ_H
+
+#include <linux/errno.h>
+#include <linux/err.h>
+
+struct pm8xxx_irq_core_data {
+ u32 rev;
+ int nirqs;
+};
+
+struct pm8xxx_irq_platform_data {
+ int irq_base;
+ struct pm8xxx_irq_core_data irq_cdata;
+ int devirq;
+ int irq_trigger_flag;
+};
+
+struct pm_irq_chip;
+
+#ifdef CONFIG_MFD_PM8XXX_IRQ
+int pm8xxx_get_irq_stat(struct pm_irq_chip *chip, int irq);
+struct pm_irq_chip * __devinit pm8xxx_irq_init(struct device *dev,
+ const struct pm8xxx_irq_platform_data *pdata);
+int __devexit pm8xxx_irq_exit(struct pm_irq_chip *chip);
+#else
+static inline int pm8xxx_get_irq_stat(struct pm_irq_chip *chip, int irq)
+{
+ return -ENXIO;
+}
+static inline struct pm_irq_chip * __devinit pm8xxx_irq_init(
+ const struct device *dev,
+ const struct pm8xxx_irq_platform_data *pdata)
+{
+ return ERR_PTR(-ENXIO);
+}
+static inline int __devexit pm8xxx_irq_exit(struct pm_irq_chip *chip)
+{
+ return -ENXIO;
+}
+#endif /* CONFIG_MFD_PM8XXX_IRQ */
+#endif /* __MFD_PM8XXX_IRQ_H */
diff --git a/include/linux/mfd/pm8xxx/pm8921.h b/include/linux/mfd/pm8xxx/pm8921.h
index 33fbe9c..d5517fd 100644
--- a/include/linux/mfd/pm8xxx/pm8921.h
+++ b/include/linux/mfd/pm8xxx/pm8921.h
@@ -19,9 +19,13 @@
#define __MFD_PM8921_H
#include <linux/device.h>
+#include <linux/mfd/pm8xxx/irq.h>
+
+#define PM8921_NR_IRQS 256
struct pm8921_platform_data {
int irq_base;
+ struct pm8xxx_irq_platform_data *irq_pdata;
};
#endif
--
1.7.1
Sent by an employee of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
^ permalink raw reply related [flat|nested] 10+ messages in thread* Re: [PM8921 MFD V4 2/6] mfd: pm8xxx: Add irq support
2011-03-18 4:21 ` [PM8921 MFD V4 2/6] mfd: pm8xxx: Add irq support adharmap
@ 2011-03-18 8:38 ` Thomas Gleixner
0 siblings, 0 replies; 10+ messages in thread
From: Thomas Gleixner @ 2011-03-18 8:38 UTC (permalink / raw)
To: Abhijeet Dharmapurikar
Cc: davidb, dwalker, Samuel Ortiz, Bryan Huntsman, linux-kernel,
linux-arm-msm, linux-arm-msm-owner, linux-arm-kernel, Mark Brown,
Linus Walleij, Greg Kroah-Hartman
On Thu, 17 Mar 2011, adharmap@codeaurora.org wrote:
> +static struct irq_chip pm8xxx_irq_chip = {
> + .name = "pm8xxx",
> + .irq_mask_ack = pm8xxx_irq_mask_ack,
> + .irq_unmask = pm8xxx_irq_unmask,
> + .irq_set_type = pm8xxx_irq_set_type,
> + .flags = IRQCHIP_MASK_ON_SUSPEND,
> +};
Ok, that looks sane now. One problem remains. You have removed the
set_wake function, which will cause the core to bail when an irq is
marked wake. So you want an set_wake() function which does nothing
else than return 0 for now. I'll have a look that we can handle that
case with a chip flag in the core.
Thanks,
tglx
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PM8921 MFD V4 3/6] gpio: pm8xxx-gpio: Add pm8xxx gpio driver
2011-03-18 4:21 [PM8921 MFD V4 0/6] pm8921 core and subdevices adharmap
2011-03-18 4:21 ` [PM8921 MFD V4 1/6] mfd: pm8921: Add PMIC 8921 core driver adharmap
2011-03-18 4:21 ` [PM8921 MFD V4 2/6] mfd: pm8xxx: Add irq support adharmap
@ 2011-03-18 4:21 ` adharmap
2011-03-18 4:21 ` [PM8921 MFD V4 4/6] mfd: pm8xxx-mpp: Add pm8xxx MPP driver adharmap
` (2 subsequent siblings)
5 siblings, 0 replies; 10+ messages in thread
From: adharmap @ 2011-03-18 4:21 UTC (permalink / raw)
To: davidb, dwalker
Cc: Abhijeet Dharmapurikar, Grant Likely, Bryan Huntsman,
Samuel Ortiz, linux-kernel, linux-arm-msm, linux-arm-msm-owner,
linux-arm-kernel, Mark Brown, Linus Walleij, Thomas Glexiner,
Greg Kroah-Hartman
Add support for GPIO on Qualcomm PM8xxx PMIC chips.
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
---
drivers/gpio/Kconfig | 8 +
drivers/gpio/Makefile | 1 +
drivers/gpio/pm8xxx-gpio.c | 451 +++++++++++++++++++++++++++++++++++++
drivers/mfd/pm8921-core.c | 36 +++
include/linux/mfd/pm8xxx/gpio.h | 133 +++++++++++
include/linux/mfd/pm8xxx/pm8921.h | 11 +
6 files changed, 640 insertions(+), 0 deletions(-)
create mode 100644 drivers/gpio/pm8xxx-gpio.c
create mode 100644 include/linux/mfd/pm8xxx/gpio.h
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 664660e..52c233e 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -411,4 +411,12 @@ config GPIO_JANZ_TTL
This driver provides support for driving the pins in output
mode only. Input mode is not supported.
+config GPIO_PM8XXX
+ tristate "Qualcomm PM8xxx GPIO support"
+ depends on MFD_PM8XXX
+ default y if MFD_PM8XXX
+ help
+ This option enables support for on-chip GPIO found on Qualcomm PM8xxx
+ PMICs.
+
endif
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 3351cf8..10efe6c 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -42,3 +42,4 @@ obj-$(CONFIG_GPIO_JANZ_TTL) += janz-ttl.o
obj-$(CONFIG_GPIO_SX150X) += sx150x.o
obj-$(CONFIG_GPIO_VX855) += vx855_gpio.o
obj-$(CONFIG_GPIO_ML_IOH) += ml_ioh_gpio.o
+obj-$(CONFIG_GPIO_PM8XXX) += pm8xxx-gpio.o
diff --git a/drivers/gpio/pm8xxx-gpio.c b/drivers/gpio/pm8xxx-gpio.c
new file mode 100644
index 0000000..c0540c3
--- /dev/null
+++ b/drivers/gpio/pm8xxx-gpio.c
@@ -0,0 +1,451 @@
+/*
+ * Qualcomm PMIC8XXX GPIO driver
+ *
+ * Copyright (c) 2011, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#define pr_fmt(fmt) "%s: " fmt, __func__
+
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/mfd/pm8xxx/core.h>
+#include <linux/mfd/pm8xxx/gpio.h>
+#include <linux/debugfs.h>
+#include <linux/uaccess.h>
+#include <linux/fs.h>
+#include <linux/seq_file.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+
+/* GPIO registers */
+#define SSBI_REG_ADDR_GPIO_BASE 0x150
+#define SSBI_REG_ADDR_GPIO(n) (SSBI_REG_ADDR_GPIO_BASE + n)
+
+/* GPIO */
+#define PM_GPIO_BANK_MASK 0x70
+#define PM_GPIO_BANK_SHIFT 4
+#define PM_GPIO_WRITE 0x80
+
+/* Bank 0 */
+#define PM_GPIO_VIN_MASK 0x0E
+#define PM_GPIO_VIN_SHIFT 1
+#define PM_GPIO_MODE_ENABLE 0x01
+
+/* Bank 1 */
+#define PM_GPIO_MODE_MASK 0x0C
+#define PM_GPIO_MODE_SHIFT 2
+#define PM_GPIO_OUT_BUFFER 0x02
+#define PM_GPIO_OUT_INVERT 0x01
+
+#define PM_GPIO_MODE_OFF 3
+#define PM_GPIO_MODE_OUTPUT 2
+#define PM_GPIO_MODE_INPUT 0
+#define PM_GPIO_MODE_BOTH 1
+
+/* Bank 2 */
+#define PM_GPIO_PULL_MASK 0x0E
+#define PM_GPIO_PULL_SHIFT 1
+
+/* Bank 3 */
+#define PM_GPIO_OUT_STRENGTH_MASK 0x0C
+#define PM_GPIO_OUT_STRENGTH_SHIFT 2
+
+/* Bank 4 */
+#define PM_GPIO_FUNC_MASK 0x0E
+#define PM_GPIO_FUNC_SHIFT 1
+
+/* Bank 5 */
+#define PM_GPIO_NON_INT_POL_INV 0x08
+#define PM_GPIO_BANKS 6
+
+struct pm_gpio_chip {
+ struct list_head link;
+ struct gpio_chip gpio_chip;
+ spinlock_t pm_lock;
+ u8 *bank1;
+ int irq_base;
+};
+
+static LIST_HEAD(pm_gpio_chips);
+static DEFINE_MUTEX(pm_gpio_chips_lock);
+
+static int pm_gpio_get(struct pm_gpio_chip *pm_gpio_chip, unsigned gpio)
+{
+ int mode;
+
+ if (gpio >= pm_gpio_chip->gpio_chip.ngpio || pm_gpio_chip == NULL)
+ return -EINVAL;
+
+ /* Get gpio value from config bank 1 if output gpio.
+ Get gpio value from IRQ RT status register for all other gpio modes.
+ */
+ mode = (pm_gpio_chip->bank1[gpio] & PM_GPIO_MODE_MASK) >>
+ PM_GPIO_MODE_SHIFT;
+ if (mode == PM_GPIO_MODE_OUTPUT)
+ return pm_gpio_chip->bank1[gpio] & PM_GPIO_OUT_INVERT;
+ else
+ return pm8xxx_read_irq_stat(pm_gpio_chip->gpio_chip.dev->parent,
+ pm_gpio_chip->irq_base + gpio);
+}
+
+static int pm_gpio_set(struct pm_gpio_chip *pm_gpio_chip,
+ unsigned gpio, int value)
+{
+ int rc;
+ u8 bank1;
+ unsigned long flags;
+
+ if (gpio >= pm_gpio_chip->gpio_chip.ngpio || pm_gpio_chip == NULL)
+ return -EINVAL;
+
+ spin_lock_irqsave(&pm_gpio_chip->pm_lock, flags);
+ bank1 = PM_GPIO_WRITE
+ | (pm_gpio_chip->bank1[gpio] & ~PM_GPIO_OUT_INVERT);
+
+ if (value)
+ bank1 |= PM_GPIO_OUT_INVERT;
+
+ pm_gpio_chip->bank1[gpio] = bank1;
+ rc = pm8xxx_writeb(pm_gpio_chip->gpio_chip.dev->parent,
+ SSBI_REG_ADDR_GPIO(gpio), bank1);
+ spin_unlock_irqrestore(&pm_gpio_chip->pm_lock, flags);
+
+ if (rc)
+ pr_err("FAIL pm8xxx_writeb(): rc=%d. "
+ "(gpio=%d, value=%d)\n",
+ rc, gpio, value);
+
+ return rc;
+}
+
+static int dir_map[] = {
+ PM_GPIO_MODE_OFF,
+ PM_GPIO_MODE_OUTPUT,
+ PM_GPIO_MODE_INPUT,
+ PM_GPIO_MODE_BOTH,
+};
+
+static int pm_gpio_set_direction(struct pm_gpio_chip *pm_gpio_chip,
+ unsigned gpio, int direction)
+{
+ int rc;
+ u8 bank1;
+ unsigned long flags;
+
+ if (!direction || pm_gpio_chip == NULL)
+ return -EINVAL;
+
+ spin_lock_irqsave(&pm_gpio_chip->pm_lock, flags);
+ bank1 = PM_GPIO_WRITE
+ | (pm_gpio_chip->bank1[gpio] & ~PM_GPIO_MODE_MASK);
+
+ bank1 |= ((dir_map[direction] << PM_GPIO_MODE_SHIFT)
+ & PM_GPIO_MODE_MASK);
+
+ pm_gpio_chip->bank1[gpio] = bank1;
+ rc = pm8xxx_writeb(pm_gpio_chip->gpio_chip.dev->parent,
+ SSBI_REG_ADDR_GPIO(gpio), bank1);
+ spin_unlock_irqrestore(&pm_gpio_chip->pm_lock, flags);
+
+ if (rc)
+ pr_err("Failed on pm8xxx_writeb(): rc=%d (GPIO config)\n",
+ rc);
+
+ return rc;
+}
+
+static int pm_gpio_init_bank1(struct pm_gpio_chip *pm_gpio_chip)
+{
+ int i, rc;
+ u8 bank;
+
+ for (i = 0; i < pm_gpio_chip->gpio_chip.ngpio; i++) {
+ bank = 1 << PM_GPIO_BANK_SHIFT;
+ rc = pm8xxx_writeb(pm_gpio_chip->gpio_chip.dev->parent,
+ SSBI_REG_ADDR_GPIO(i),
+ bank);
+ if (rc) {
+ pr_err("error setting bank rc=%d\n", rc);
+ return rc;
+ }
+
+ rc = pm8xxx_readb(pm_gpio_chip->gpio_chip.dev->parent,
+ SSBI_REG_ADDR_GPIO(i),
+ &pm_gpio_chip->bank1[i]);
+ if (rc) {
+ pr_err("error reading bank 1 rc=%d\n", rc);
+ return rc;
+ }
+ }
+ return 0;
+}
+
+static int pm_gpio_to_irq(struct gpio_chip *gpio_chip, unsigned offset)
+{
+ struct pm_gpio_chip *pm_gpio_chip = dev_get_drvdata(gpio_chip->dev);
+
+ return pm_gpio_chip->irq_base + offset;
+}
+
+static int pm_gpio_read(struct gpio_chip *gpio_chip, unsigned offset)
+{
+ struct pm_gpio_chip *pm_gpio_chip = dev_get_drvdata(gpio_chip->dev);
+
+ return pm_gpio_get(pm_gpio_chip, offset);
+}
+
+static void pm_gpio_write(struct gpio_chip *gpio_chip,
+ unsigned offset, int val)
+{
+ struct pm_gpio_chip *pm_gpio_chip = dev_get_drvdata(gpio_chip->dev);
+
+ pm_gpio_set(pm_gpio_chip, offset, val);
+}
+
+static int pm_gpio_direction_input(struct gpio_chip *gpio_chip,
+ unsigned offset)
+{
+ struct pm_gpio_chip *pm_gpio_chip = dev_get_drvdata(gpio_chip->dev);
+
+ return pm_gpio_set_direction(pm_gpio_chip, offset, PM_GPIO_DIR_IN);
+}
+
+static int pm_gpio_direction_output(struct gpio_chip *gpio_chip,
+ unsigned offset,
+ int val)
+{
+ int ret;
+ struct pm_gpio_chip *pm_gpio_chip = dev_get_drvdata(gpio_chip->dev);
+
+ ret = pm_gpio_set_direction(pm_gpio_chip, offset, PM_GPIO_DIR_OUT);
+ if (!ret)
+ ret = pm_gpio_set(pm_gpio_chip, offset, val);
+
+ return ret;
+}
+
+static void pm_gpio_dbg_show(struct seq_file *s, struct gpio_chip *gpio_chip)
+{
+ static const char * const cmode[] = { "in", "in/out", "out", "off" };
+ struct pm_gpio_chip *pm_gpio_chip = dev_get_drvdata(gpio_chip->dev);
+ u8 mode, state, bank;
+ const char *label;
+ int i, j;
+
+ for (i = 0; i < gpio_chip->ngpio; i++) {
+ label = gpiochip_is_requested(gpio_chip, i);
+ mode = (pm_gpio_chip->bank1[i] & PM_GPIO_MODE_MASK) >>
+ PM_GPIO_MODE_SHIFT;
+ state = pm_gpio_get(pm_gpio_chip, i);
+ seq_printf(s, "gpio-%-3d (%-12.12s) %-10.10s"
+ " %s",
+ gpio_chip->base + i,
+ label ? label : "--",
+ cmode[mode],
+ state ? "hi" : "lo");
+ for (j = 0; j < PM_GPIO_BANKS; j++) {
+ bank = j << PM_GPIO_BANK_SHIFT;
+ pm8xxx_writeb(gpio_chip->dev->parent,
+ SSBI_REG_ADDR_GPIO(i),
+ bank);
+ pm8xxx_readb(gpio_chip->dev->parent,
+ SSBI_REG_ADDR_GPIO(i),
+ &bank);
+ seq_printf(s, " 0x%02x", bank);
+ }
+ seq_printf(s, "\n");
+ }
+}
+
+static int __devinit pm_gpio_probe(struct platform_device *pdev)
+{
+ int ret;
+ const struct pm8xxx_gpio_platform_data *pdata = pdev->dev.platform_data;
+ struct pm_gpio_chip *pm_gpio_chip;
+
+ if (!pdata) {
+ pr_err("missing platform data\n");
+ return -EINVAL;
+ }
+
+ pm_gpio_chip = kzalloc(sizeof(struct pm_gpio_chip), GFP_KERNEL);
+ if (!pm_gpio_chip) {
+ pr_err("Cannot allocate pm_gpio_chip\n");
+ return -ENOMEM;
+ }
+
+ pm_gpio_chip->bank1 = kzalloc(sizeof(u8) * pdata->gpio_cdata.ngpios,
+ GFP_KERNEL);
+ if (!pm_gpio_chip->bank1) {
+ pr_err("Cannot allocate pm_gpio_chip->bank1\n");
+ return -ENOMEM;
+ }
+
+ spin_lock_init(&pm_gpio_chip->pm_lock);
+ pm_gpio_chip->gpio_chip.label = "pm-gpio";
+ pm_gpio_chip->gpio_chip.direction_input = pm_gpio_direction_input;
+ pm_gpio_chip->gpio_chip.direction_output = pm_gpio_direction_output;
+ pm_gpio_chip->gpio_chip.to_irq = pm_gpio_to_irq;
+ pm_gpio_chip->gpio_chip.get = pm_gpio_read;
+ pm_gpio_chip->gpio_chip.set = pm_gpio_write;
+ pm_gpio_chip->gpio_chip.dbg_show = pm_gpio_dbg_show;
+ pm_gpio_chip->gpio_chip.ngpio = pdata->gpio_cdata.ngpios;
+ pm_gpio_chip->gpio_chip.can_sleep = 1;
+ pm_gpio_chip->gpio_chip.dev = &pdev->dev;
+ pm_gpio_chip->gpio_chip.base = pdata->gpio_base;
+ pm_gpio_chip->irq_base = platform_get_irq(pdev, 0);
+ mutex_lock(&pm_gpio_chips_lock);
+ list_add(&pm_gpio_chip->link, &pm_gpio_chips);
+ mutex_unlock(&pm_gpio_chips_lock);
+ platform_set_drvdata(pdev, pm_gpio_chip);
+
+ ret = gpiochip_add(&pm_gpio_chip->gpio_chip);
+ if (ret) {
+ pr_err("gpiochip_add failed ret = %d\n", ret);
+ goto reset_drvdata;
+ }
+
+ ret = pm_gpio_init_bank1(pm_gpio_chip);
+ if (ret) {
+ pr_err("gpio init bank failed ret = %d\n", ret);
+ goto remove_chip;
+ }
+
+ return 0;
+
+remove_chip:
+ if (gpiochip_remove(&pm_gpio_chip->gpio_chip))
+ pr_err("failed to remove gpio chip\n");
+reset_drvdata:
+ platform_set_drvdata(pdev, NULL);
+ kfree(pm_gpio_chip);
+ return ret;
+}
+
+static int __devexit pm_gpio_remove(struct platform_device *pdev)
+{
+ struct pm_gpio_chip *pm_gpio_chip
+ = platform_get_drvdata(pdev);
+
+ mutex_lock(&pm_gpio_chips_lock);
+ list_del(&pm_gpio_chip->link);
+ mutex_unlock(&pm_gpio_chips_lock);
+ platform_set_drvdata(pdev, NULL);
+ if (gpiochip_remove(&pm_gpio_chip->gpio_chip))
+ pr_err("failed to remove gpio chip\n");
+ kfree(pm_gpio_chip->bank1);
+ kfree(pm_gpio_chip);
+ return 0;
+}
+
+int pm8xxx_gpio_config(int gpio, struct pm_gpio *param)
+{
+ int rc, pm_gpio = 0;
+ u8 bank[8];
+ unsigned long flags;
+ struct pm_gpio_chip *pm_gpio_chip;
+ struct gpio_chip *gpio_chip;
+
+ if (param == NULL)
+ return -EINVAL;
+
+ mutex_lock(&pm_gpio_chips_lock);
+ list_for_each_entry(pm_gpio_chip, &pm_gpio_chips, link) {
+ gpio_chip = &pm_gpio_chip->gpio_chip;
+ if (gpio >= gpio_chip->base
+ && gpio < gpio_chip->base + gpio_chip->ngpio) {
+ pm_gpio = gpio - gpio_chip->base;
+ break;
+ }
+ }
+ mutex_unlock(&pm_gpio_chips_lock);
+ if (!pm_gpio) {
+ pr_err("called on gpio %d not handled by any pmic\n", gpio);
+ return -EINVAL;
+ }
+
+ /* Select banks and configure the gpio */
+ bank[0] = PM_GPIO_WRITE |
+ ((param->vin_sel << PM_GPIO_VIN_SHIFT) &
+ PM_GPIO_VIN_MASK) |
+ PM_GPIO_MODE_ENABLE;
+ bank[1] = PM_GPIO_WRITE |
+ ((1 << PM_GPIO_BANK_SHIFT) &
+ PM_GPIO_BANK_MASK) |
+ ((dir_map[param->direction] <<
+ PM_GPIO_MODE_SHIFT) &
+ PM_GPIO_MODE_MASK) |
+ ((param->direction & PM_GPIO_DIR_OUT) ?
+ ((param->output_buffer & 1) ?
+ PM_GPIO_OUT_BUFFER : 0) : 0) |
+ ((param->direction & PM_GPIO_DIR_OUT) ?
+ param->output_value & 0x01 : 0);
+ bank[2] = PM_GPIO_WRITE |
+ ((2 << PM_GPIO_BANK_SHIFT) &
+ PM_GPIO_BANK_MASK) |
+ ((param->pull << PM_GPIO_PULL_SHIFT) &
+ PM_GPIO_PULL_MASK);
+ bank[3] = PM_GPIO_WRITE |
+ ((3 << PM_GPIO_BANK_SHIFT) &
+ PM_GPIO_BANK_MASK) |
+ ((param->out_strength <<
+ PM_GPIO_OUT_STRENGTH_SHIFT) &
+ PM_GPIO_OUT_STRENGTH_MASK);
+ bank[4] = PM_GPIO_WRITE |
+ ((4 << PM_GPIO_BANK_SHIFT) &
+ PM_GPIO_BANK_MASK) |
+ ((param->function << PM_GPIO_FUNC_SHIFT) &
+ PM_GPIO_FUNC_MASK);
+ bank[5] = PM_GPIO_WRITE |
+ ((5 << PM_GPIO_BANK_SHIFT) & PM_GPIO_BANK_MASK) |
+ (param->inv_int_pol ? 0 : PM_GPIO_NON_INT_POL_INV);
+
+ spin_lock_irqsave(&pm_gpio_chip->pm_lock, flags);
+ /* Remember bank1 for later use */
+ pm_gpio_chip->bank1[pm_gpio] = bank[1];
+ rc = pm8xxx_write_buf(pm_gpio_chip->gpio_chip.dev->parent,
+ SSBI_REG_ADDR_GPIO(pm_gpio), bank, 6);
+ spin_unlock_irqrestore(&pm_gpio_chip->pm_lock, flags);
+
+ if (rc)
+ pr_err("Failed on pm8xxx_write_buf() rc=%d (GPIO config)\n",
+ rc);
+
+ return rc;
+}
+EXPORT_SYMBOL_GPL(pm8xxx_gpio_config);
+
+static struct platform_driver pm_gpio_driver = {
+ .probe = pm_gpio_probe,
+ .remove = __devexit_p(pm_gpio_remove),
+ .driver = {
+ .name = PM8XXX_GPIO_DEV_NAME,
+ .owner = THIS_MODULE,
+ },
+};
+
+static int __init pm_gpio_init(void)
+{
+ return platform_driver_register(&pm_gpio_driver);
+}
+subsys_initcall(pm_gpio_init);
+
+static void __exit pm_gpio_exit(void)
+{
+ platform_driver_unregister(&pm_gpio_driver);
+}
+module_exit(pm_gpio_exit);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("PMIC GPIO driver");
+MODULE_VERSION("1.0");
+MODULE_ALIAS("platform:" PM8XXX_GPIO_DEV_NAME);
diff --git a/drivers/mfd/pm8921-core.c b/drivers/mfd/pm8921-core.c
index e873b15..3932bee 100644
--- a/drivers/mfd/pm8921-core.c
+++ b/drivers/mfd/pm8921-core.c
@@ -80,6 +80,22 @@ static struct pm8xxx_drvdata pm8921_drvdata = {
.pmic_read_irq_stat = pm8921_read_irq_stat,
};
+static const struct resource gpio_cell_resources[] __devinitconst = {
+ [0] = {
+ .start = PM8921_IRQ_BLOCK_BIT(PM8921_GPIO_BLOCK_START, 0),
+ .end = PM8921_IRQ_BLOCK_BIT(PM8921_GPIO_BLOCK_START, 0)
+ + PM8921_NR_GPIOS - 1,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct mfd_cell gpio_cell __devinitdata = {
+ .name = PM8XXX_GPIO_DEV_NAME,
+ .id = -1,
+ .resources = gpio_cell_resources,
+ .num_resources = ARRAY_SIZE(gpio_cell_resources),
+};
+
static int __devinit pm8921_add_subdevices(const struct pm8921_platform_data
*pdata,
struct pm8921 *pmic,
@@ -101,6 +117,26 @@ static int __devinit pm8921_add_subdevices(const struct pm8921_platform_data
}
pmic->irq_chip = irq_chip;
}
+
+ if (pdata->gpio_pdata) {
+ pdata->gpio_pdata->gpio_cdata.ngpios = PM8921_NR_GPIOS;
+ pdata->gpio_pdata->gpio_cdata.rev = rev;
+ gpio_cell.platform_data = pdata->gpio_pdata;
+ gpio_cell.data_size = sizeof(struct pm8xxx_gpio_platform_data);
+ ret = mfd_add_devices(pmic->dev, 0, &gpio_cell, 1,
+ NULL, irq_base);
+ if (ret) {
+ pr_err("Failed to add gpio subdevice ret=%d\n", ret);
+ goto bail;
+ }
+ }
+
+ return 0;
+bail:
+ if (pmic->irq_chip) {
+ pm8xxx_irq_exit(pmic->irq_chip);
+ pmic->irq_chip = NULL;
+ }
return ret;
}
diff --git a/include/linux/mfd/pm8xxx/gpio.h b/include/linux/mfd/pm8xxx/gpio.h
new file mode 100644
index 0000000..2c57630
--- /dev/null
+++ b/include/linux/mfd/pm8xxx/gpio.h
@@ -0,0 +1,133 @@
+/*
+ * Copyright (c) 2011, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/*
+ * Qualcomm PMIC8XXX gpio driver header file
+ *
+ */
+
+#ifndef __PM8XXX_GPIO_H
+#define __PM8XXX_GPIO_H
+
+#include <linux/errno.h>
+
+#define PM8XXX_GPIO_DEV_NAME "pm8xxx-gpio"
+
+struct pm8xxx_gpio_core_data {
+ u32 rev;
+ int ngpios;
+};
+
+struct pm8xxx_gpio_platform_data {
+ struct pm8xxx_gpio_core_data gpio_cdata;
+ int gpio_base;
+};
+
+/* GPIO parameters */
+/* direction */
+#define PM_GPIO_DIR_OUT 0x01
+#define PM_GPIO_DIR_IN 0x02
+#define PM_GPIO_DIR_BOTH (PM_GPIO_DIR_OUT | PM_GPIO_DIR_IN)
+
+/* output_buffer */
+#define PM_GPIO_OUT_BUF_OPEN_DRAIN 1
+#define PM_GPIO_OUT_BUF_CMOS 0
+
+/* pull */
+#define PM_GPIO_PULL_UP_30 0
+#define PM_GPIO_PULL_UP_1P5 1
+#define PM_GPIO_PULL_UP_31P5 2
+#define PM_GPIO_PULL_UP_1P5_30 3
+#define PM_GPIO_PULL_DN 4
+#define PM_GPIO_PULL_NO 5
+
+/* vin_sel: Voltage Input Select */
+#define PM_GPIO_VIN_VPH 0
+#define PM_GPIO_VIN_BB 1
+#define PM_GPIO_VIN_S3 2
+#define PM_GPIO_VIN_L3 3
+#define PM_GPIO_VIN_L7 4
+#define PM_GPIO_VIN_L6 5
+#define PM_GPIO_VIN_L5 6
+#define PM_GPIO_VIN_L2 7
+
+/* out_strength */
+#define PM_GPIO_STRENGTH_NO 0
+#define PM_GPIO_STRENGTH_HIGH 1
+#define PM_GPIO_STRENGTH_MED 2
+#define PM_GPIO_STRENGTH_LOW 3
+
+/* function */
+#define PM_GPIO_FUNC_NORMAL 0
+#define PM_GPIO_FUNC_PAIRED 1
+#define PM_GPIO_FUNC_1 2
+#define PM_GPIO_FUNC_2 3
+#define PM_GPIO_DTEST1 4
+#define PM_GPIO_DTEST2 5
+#define PM_GPIO_DTEST3 6
+#define PM_GPIO_DTEST4 7
+
+/**
+ * struct pm_gpio - structure to specify gpio configurtion values
+ * @direction: indicates whether the gpio should be input, output, or
+ * both. Should be of the type PM_GPIO_DIR_*
+ * @output_buffer: indicates gpio should be configured as CMOS or open
+ * drain. Should be of the type PM_GPIO_OUT_BUF_*
+ * @output_value: The gpio output value of the gpio line - 0 or 1
+ * @pull: Indicates whether a pull up or pull down should be
+ * applied. If a pullup is required the current strength
+ * needs to be specified. Current values of 30uA, 1.5uA,
+ * 31.5uA, 1.5uA with 30uA boost are supported. This value
+ * should be one of the PM_GPIO_PULL_*
+ * @vin_sel: specifies the voltage level when the output is set to 1.
+ * For an input gpio specifies the voltage level at which
+ * the input is interpreted as a logical 1.
+ * @out_strength: the amount of current supplied for an output gpio,
+ * should be of the type PM_GPIO_STRENGTH_*
+ * @function: choose alternate function for the gpio. Certain gpios
+ * can be paired (shorted) with each other. Some gpio pin
+ * can act as alternate functions. This parameter should
+ * be of type PM_GPIO_FUNC_*
+ * @inv_int_pol: Invert polarity before feeding the line to the interrupt
+ * module in pmic. This feature will almost be never used
+ * since the pm8xxx interrupt block can detect both edges
+ * and both levels.
+ */
+struct pm_gpio {
+ int direction;
+ int output_buffer;
+ int output_value;
+ int pull;
+ int vin_sel;
+ int out_strength;
+ int function;
+ int inv_int_pol;
+};
+
+#if defined(CONFIG_GPIO_PM8XXX) || defined(CONFIG_GPIO_PM8XXX_MODULE)
+/**
+ * pm8xxx_gpio_config - configure a gpio controlled by a pm8xxx chip
+ * @gpio: gpio number to configure
+ * @param: configuration values
+ *
+ * RETURNS: an appropriate -ERRNO error value on error, or zero for success.
+ */
+int pm8xxx_gpio_config(int gpio, struct pm_gpio *param);
+#else
+static inline int pm8xxx_gpio_config(int gpio, struct pm_gpio *param)
+{
+ return -ENXIO;
+}
+#endif
+
+#endif
diff --git a/include/linux/mfd/pm8xxx/pm8921.h b/include/linux/mfd/pm8xxx/pm8921.h
index d5517fd..def8c31 100644
--- a/include/linux/mfd/pm8xxx/pm8921.h
+++ b/include/linux/mfd/pm8xxx/pm8921.h
@@ -20,12 +20,23 @@
#include <linux/device.h>
#include <linux/mfd/pm8xxx/irq.h>
+#include <linux/mfd/pm8xxx/gpio.h>
#define PM8921_NR_IRQS 256
+#define PM8921_NR_GPIOS 44
+
+#define PM8921_GPIO_BLOCK_START 24
+#define PM8921_IRQ_BLOCK_BIT(block, bit) ((block) * 8 + (bit))
+
+/* GPIOs [1,N] */
+#define PM8921_GPIO_IRQ(base, gpio) ((base) + \
+ PM8921_IRQ_BLOCK_BIT(PM8921_GPIO_BLOCK_START, (gpio)-1))
+
struct pm8921_platform_data {
int irq_base;
struct pm8xxx_irq_platform_data *irq_pdata;
+ struct pm8xxx_gpio_platform_data *gpio_pdata;
};
#endif
--
1.7.1
Sent by an employee of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PM8921 MFD V4 4/6] mfd: pm8xxx-mpp: Add pm8xxx MPP driver
2011-03-18 4:21 [PM8921 MFD V4 0/6] pm8921 core and subdevices adharmap
` (2 preceding siblings ...)
2011-03-18 4:21 ` [PM8921 MFD V4 3/6] gpio: pm8xxx-gpio: Add pm8xxx gpio driver adharmap
@ 2011-03-18 4:21 ` adharmap
2011-03-22 18:45 ` Abhijeet Dharmapurikar
2011-03-18 4:21 ` [PM8921 MFD V4 5/6] MAINTAINERS: Add patterns for pmic 8921 files to MSM subsystem adharmap
2011-03-18 4:21 ` [PM8921 MFD V4 6/6] msm: board-8960: Add support for pm8921 adharmap
5 siblings, 1 reply; 10+ messages in thread
From: adharmap @ 2011-03-18 4:21 UTC (permalink / raw)
To: davidb, dwalker
Cc: David Collins, Grant Likely, Bryan Huntsman, Samuel Ortiz,
linux-kernel, linux-arm-msm, linux-arm-msm-owner,
linux-arm-kernel, Mark Brown, Linus Walleij, Thomas Glexiner,
Greg Kroah-Hartman
From: David Collins <collinsd@codeaurora.org>
Add support for multi-purpose pins (MPPs) on Qualcomm PM8xxx
PMIC chips.
PM8xxx MPPs can be configured as digital or analog inputs or
outputs, current sinks, or buffers.
Note that mpp pins appear as gpio lines to the kernel. However they
are implemented separately from the pmic's gpio driver as
mpps have different configuration attributes and have different
register controls than the pmic's gpio controller. Basically they are
different set of pins.
Signed-off-by: David Collins <collinsd@codeaurora.org>
---
drivers/gpio/Kconfig | 8 +
drivers/gpio/Makefile | 1 +
drivers/gpio/pm8xxx-mpp.c | 326 +++++++++++++++++++++++++++++++++++++
drivers/mfd/pm8921-core.c | 31 ++++
include/linux/mfd/pm8xxx/mpp.h | 233 ++++++++++++++++++++++++++
include/linux/mfd/pm8xxx/pm8921.h | 9 +-
6 files changed, 607 insertions(+), 1 deletions(-)
create mode 100644 drivers/gpio/pm8xxx-mpp.c
create mode 100644 include/linux/mfd/pm8xxx/mpp.h
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 52c233e..7ada3b1 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -419,4 +419,12 @@ config GPIO_PM8XXX
This option enables support for on-chip GPIO found on Qualcomm PM8xxx
PMICs.
+config MFD_PM8XXX_MPP
+ tristate "Support for Qualcomm PM8xxx MPP features"
+ depends on MFD_PM8XXX
+ default y if MFD_PM8XXX
+ help
+ This is the multi-purpose pin (MPP) driver for Qualcomm PM 8xxx PMIC
+ chips.
+
endif
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 10efe6c..0452caf 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -43,3 +43,4 @@ obj-$(CONFIG_GPIO_SX150X) += sx150x.o
obj-$(CONFIG_GPIO_VX855) += vx855_gpio.o
obj-$(CONFIG_GPIO_ML_IOH) += ml_ioh_gpio.o
obj-$(CONFIG_GPIO_PM8XXX) += pm8xxx-gpio.o
+obj-$(CONFIG_MFD_PM8XXX_MPP) += pm8xxx-mpp.o
diff --git a/drivers/gpio/pm8xxx-mpp.c b/drivers/gpio/pm8xxx-mpp.c
new file mode 100644
index 0000000..6e90e91
--- /dev/null
+++ b/drivers/gpio/pm8xxx-mpp.c
@@ -0,0 +1,326 @@
+/*
+ * Qualcomm PM8XXX Multi-Purpose Pin (MPP) driver
+ *
+ * Copyright (c) 2011, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#define pr_fmt(fmt) "%s: " fmt, __func__
+
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/seq_file.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/mfd/pm8xxx/core.h>
+#include <linux/mfd/pm8xxx/mpp.h>
+
+/* MPP Type */
+#define PM8XXX_MPP_TYPE_MASK 0xE0
+#define PM8XXX_MPP_TYPE_SHIFT 5
+
+/* MPP Config Level */
+#define PM8XXX_MPP_CONFIG_LVL_MASK 0x1C
+#define PM8XXX_MPP_CONFIG_LVL_SHIFT 2
+
+/* MPP Config Control */
+#define PM8XXX_MPP_CONFIG_CTRL_MASK 0x03
+#define PM8XXX_MPP_CONFIG_CTRL_SHIFT 0
+
+struct pm8xxx_mpp_chip {
+ struct list_head link;
+ struct gpio_chip gpio_chip;
+ spinlock_t pm_lock;
+ u8 *ctrl_reg;
+ int mpp_base;
+ int irq_base;
+ int nmpps;
+ u16 base_addr;
+};
+
+static LIST_HEAD(pm8xxx_mpp_chips);
+static DEFINE_MUTEX(pm8xxx_mpp_chips_lock);
+
+static int pm8xxx_mpp_write(struct pm8xxx_mpp_chip *mpp_chip, u16 offset,
+ u8 val, u8 mask)
+{
+ u8 reg;
+ int rc;
+ unsigned long flags;
+
+ spin_lock_irqsave(&mpp_chip->pm_lock, flags);
+
+ reg = (mpp_chip->ctrl_reg[offset] & ~mask) | (val & mask);
+ rc = pm8xxx_writeb(mpp_chip->gpio_chip.dev->parent,
+ mpp_chip->base_addr + offset, reg);
+ if (!rc)
+ mpp_chip->ctrl_reg[offset] = reg;
+
+ spin_unlock_irqrestore(&mpp_chip->pm_lock, flags);
+
+ return rc;
+}
+
+static int pm8xxx_mpp_to_irq(struct gpio_chip *chip, unsigned offset)
+{
+ struct pm8xxx_mpp_chip *mpp_chip = dev_get_drvdata(chip->dev);
+
+ return mpp_chip->irq_base + offset;
+}
+
+static int pm8xxx_mpp_get(struct gpio_chip *chip, unsigned offset)
+{
+ struct pm8xxx_mpp_chip *mpp_chip = dev_get_drvdata(chip->dev);
+ int rc;
+
+ if ((mpp_chip->ctrl_reg[offset] & PM8XXX_MPP_TYPE_MASK) >>
+ PM8XXX_MPP_TYPE_SHIFT == PM8XXX_MPP_TYPE_D_OUTPUT)
+ rc = mpp_chip->ctrl_reg[offset] & PM8XXX_MPP_CONFIG_CTRL_MASK;
+ else
+ rc = pm8xxx_read_irq_stat(mpp_chip->gpio_chip.dev->parent,
+ mpp_chip->irq_base + offset);
+
+ return rc;
+}
+
+static void pm8xxx_mpp_set(struct gpio_chip *chip, unsigned offset, int val)
+{
+ struct pm8xxx_mpp_chip *mpp_chip = dev_get_drvdata(chip->dev);
+ u8 reg = val ? PM8XXX_MPP_DOUT_CTRL_HIGH : PM8XXX_MPP_DOUT_CTRL_LOW;
+ int rc;
+
+ rc = pm8xxx_mpp_write(mpp_chip, offset, reg,
+ PM8XXX_MPP_CONFIG_CTRL_MASK);
+ if (rc)
+ pr_err("pm8xxx_mpp_write(): rc=%d\n", rc);
+}
+
+static int pm8xxx_mpp_dir_input(struct gpio_chip *chip, unsigned offset)
+{
+ struct pm8xxx_mpp_chip *mpp_chip = dev_get_drvdata(chip->dev);
+ int rc = pm8xxx_mpp_write(mpp_chip, offset,
+ PM8XXX_MPP_TYPE_D_INPUT << PM8XXX_MPP_TYPE_SHIFT,
+ PM8XXX_MPP_TYPE_MASK);
+
+ if (rc)
+ pr_err("pm8xxx_mpp_write(): rc=%d\n", rc);
+ return rc;
+}
+
+static int pm8xxx_mpp_dir_output(struct gpio_chip *chip,
+ unsigned offset, int val)
+{
+ struct pm8xxx_mpp_chip *mpp_chip = dev_get_drvdata(chip->dev);
+ u8 reg = (PM8XXX_MPP_TYPE_D_OUTPUT << PM8XXX_MPP_TYPE_SHIFT) |
+ (val & PM8XXX_MPP_CONFIG_CTRL_MASK);
+ u8 mask = PM8XXX_MPP_TYPE_MASK | PM8XXX_MPP_CONFIG_CTRL_MASK;
+ int rc = pm8xxx_mpp_write(mpp_chip, offset, reg, mask);
+
+ if (rc)
+ pr_err("pm8xxx_mpp_write(): rc=%d\n", rc);
+ return rc;
+}
+
+static void pm8xxx_mpp_dbg_show(struct seq_file *s, struct gpio_chip *chip)
+{
+ static const char * const ctype[] = { "d_in", "d_out", "bi_dir",
+ "a_in", "a_out", "sink",
+ "dtest_sink", "dtest_out"
+ };
+ struct pm8xxx_mpp_chip *mpp_chip = dev_get_drvdata(chip->dev);
+ u8 type, state;
+ const char *label;
+ int i;
+
+ for (i = 0; i < mpp_chip->nmpps; i++) {
+ label = gpiochip_is_requested(chip, i);
+ type = (mpp_chip->ctrl_reg[i] & PM8XXX_MPP_TYPE_MASK) >>
+ PM8XXX_MPP_TYPE_SHIFT;
+ state = pm8xxx_mpp_get(chip, i);
+ seq_printf(s, "gpio-%-3d (%-12.12s) %-10.10s"
+ " %s 0x%02x\n",
+ chip->base + i,
+ label ? label : "--",
+ ctype[type],
+ state ? "hi" : "lo",
+ mpp_chip->ctrl_reg[i]);
+ }
+}
+
+int pm8xxx_mpp_config(unsigned mpp, unsigned type, unsigned level,
+ unsigned control)
+{
+ struct pm8xxx_mpp_chip *mpp_chip;
+ int rc, found = 0;
+ u8 config, mask;
+
+ mutex_lock(&pm8xxx_mpp_chips_lock);
+ list_for_each_entry(mpp_chip, &pm8xxx_mpp_chips, link) {
+ if (mpp >= mpp_chip->mpp_base
+ && mpp < mpp_chip->mpp_base + mpp_chip->nmpps) {
+ found = 1;
+ break;
+ }
+ }
+ mutex_unlock(&pm8xxx_mpp_chips_lock);
+ if (!found) {
+ pr_err("called on mpp %d not handled by any pmic\n", mpp);
+ return -EINVAL;
+ }
+
+ mask = PM8XXX_MPP_TYPE_MASK | PM8XXX_MPP_CONFIG_LVL_MASK |
+ PM8XXX_MPP_CONFIG_CTRL_MASK;
+ config = (type << PM8XXX_MPP_TYPE_SHIFT) & PM8XXX_MPP_TYPE_MASK;
+ config |= (level << PM8XXX_MPP_CONFIG_LVL_SHIFT) &
+ PM8XXX_MPP_CONFIG_LVL_MASK;
+ config |= control & PM8XXX_MPP_CONFIG_CTRL_MASK;
+
+ rc = pm8xxx_mpp_write(mpp_chip, mpp - mpp_chip->mpp_base, config, mask);
+
+ if (rc)
+ pr_err("pm8xxx_mpp_write(): rc=%d\n", rc);
+
+ return rc;
+}
+EXPORT_SYMBOL_GPL(pm8xxx_mpp_config);
+
+static int __devinit pm8xxx_mpp_reg_init(struct pm8xxx_mpp_chip *mpp_chip)
+{
+ int rc, i;
+
+ for (i = 0; i < mpp_chip->nmpps; i++) {
+ rc = pm8xxx_readb(mpp_chip->gpio_chip.dev->parent,
+ mpp_chip->base_addr + i,
+ &mpp_chip->ctrl_reg[i]);
+ if (rc) {
+ pr_err("failed to read register 0x%x rc=%d\n",
+ mpp_chip->base_addr + i, rc);
+ return rc;
+ }
+ }
+ return 0;
+}
+
+static int __devinit pm8xxx_mpp_probe(struct platform_device *pdev)
+{
+ int rc;
+ const struct pm8xxx_mpp_platform_data *pdata = pdev->dev.platform_data;
+ struct pm8xxx_mpp_chip *mpp_chip;
+
+ if (!pdata) {
+ pr_err("missing platform data\n");
+ return -EINVAL;
+ }
+
+ mpp_chip = kzalloc(sizeof(struct pm8xxx_mpp_chip), GFP_KERNEL);
+ if (!mpp_chip) {
+ pr_err("Cannot allocate %d bytes\n",
+ sizeof(struct pm8xxx_mpp_chip));
+ return -ENOMEM;
+ }
+
+ mpp_chip->ctrl_reg = kzalloc(pdata->core_data.nmpps, GFP_KERNEL);
+ if (!mpp_chip->ctrl_reg) {
+ pr_err("Cannot allocate %d bytes\n", pdata->core_data.nmpps);
+ rc = -ENOMEM;
+ goto free_mpp_chip;
+ }
+
+ spin_lock_init(&mpp_chip->pm_lock);
+
+ mpp_chip->gpio_chip.label = PM8XXX_MPP_DEV_NAME;
+ mpp_chip->gpio_chip.direction_input = pm8xxx_mpp_dir_input;
+ mpp_chip->gpio_chip.direction_output = pm8xxx_mpp_dir_output;
+ mpp_chip->gpio_chip.to_irq = pm8xxx_mpp_to_irq;
+ mpp_chip->gpio_chip.get = pm8xxx_mpp_get;
+ mpp_chip->gpio_chip.set = pm8xxx_mpp_set;
+ mpp_chip->gpio_chip.dbg_show = pm8xxx_mpp_dbg_show;
+ mpp_chip->gpio_chip.ngpio = pdata->core_data.nmpps;
+ mpp_chip->gpio_chip.can_sleep = 1;
+ mpp_chip->gpio_chip.dev = &pdev->dev;
+ mpp_chip->gpio_chip.base = pdata->mpp_base;
+ mpp_chip->irq_base = platform_get_irq(pdev, 0);
+ mpp_chip->mpp_base = pdata->mpp_base;
+ mpp_chip->base_addr = pdata->core_data.base_addr;
+ mpp_chip->nmpps = pdata->core_data.nmpps;
+
+ mutex_unlock(&pm8xxx_mpp_chips_lock);
+ list_add(&mpp_chip->link, &pm8xxx_mpp_chips);
+ mutex_lock(&pm8xxx_mpp_chips_lock);
+
+ platform_set_drvdata(pdev, mpp_chip);
+
+ rc = gpiochip_add(&mpp_chip->gpio_chip);
+ if (rc) {
+ pr_err("gpiochip_add failed, rc=%d\n", rc);
+ goto reset_drvdata;
+ }
+
+ rc = pm8xxx_mpp_reg_init(mpp_chip);
+ if (rc) {
+ pr_err("failed to read MPP ctrl registers, rc=%d\n", rc);
+ goto remove_chip;
+ }
+
+ return 0;
+
+remove_chip:
+ if (gpiochip_remove(&mpp_chip->gpio_chip))
+ pr_err("failed to remove gpio chip\n");
+reset_drvdata:
+ platform_set_drvdata(pdev, NULL);
+ mutex_destroy(&mpp_chip->pm_lock);
+free_mpp_chip:
+ kfree(mpp_chip);
+ return rc;
+}
+
+static int __devexit pm8xxx_mpp_remove(struct platform_device *pdev)
+{
+ struct pm8xxx_mpp_chip *mpp_chip = platform_get_drvdata(pdev);
+
+ mutex_lock(&pm8xxx_mpp_chips_lock);
+ list_del(&mpp_chip->link);
+ mutex_unlock(&pm8xxx_mpp_chips_lock);
+ platform_set_drvdata(pdev, NULL);
+ if (gpiochip_remove(&mpp_chip->gpio_chip))
+ pr_err("failed to remove gpio chip\n");
+ kfree(mpp_chip->ctrl_reg);
+ kfree(mpp_chip);
+
+ return 0;
+}
+
+static struct platform_driver pm8xxx_mpp_driver = {
+ .probe = pm8xxx_mpp_probe,
+ .remove = __devexit_p(pm8xxx_mpp_remove),
+ .driver = {
+ .name = PM8XXX_MPP_DEV_NAME,
+ .owner = THIS_MODULE,
+ },
+};
+
+static int __init pm8xxx_mpp_init(void)
+{
+ return platform_driver_register(&pm8xxx_mpp_driver);
+}
+subsys_initcall(pm8xxx_mpp_init);
+
+static void __exit pm8xxx_mpp_exit(void)
+{
+ platform_driver_unregister(&pm8xxx_mpp_driver);
+}
+module_exit(pm8xxx_mpp_exit);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("PM8XXX MPP driver");
+MODULE_VERSION("1.0");
+MODULE_ALIAS("platform:" PM8XXX_MPP_DEV_NAME);
diff --git a/drivers/mfd/pm8921-core.c b/drivers/mfd/pm8921-core.c
index 3932bee..d0a991c 100644
--- a/drivers/mfd/pm8921-core.c
+++ b/drivers/mfd/pm8921-core.c
@@ -25,6 +25,8 @@
#define REG_HWREV 0x002 /* PMIC4 revision */
#define REG_HWREV_2 0x0E8 /* PMIC4 revision 2 */
+#define REG_MPP_BASE 0x050
+
struct pm8921 {
struct device *dev;
struct pm_irq_chip *irq_chip;
@@ -96,6 +98,22 @@ static struct mfd_cell gpio_cell __devinitdata = {
.num_resources = ARRAY_SIZE(gpio_cell_resources),
};
+static const struct resource mpp_cell_resources[] __devinitconst = {
+ {
+ .start = PM8921_IRQ_BLOCK_BIT(PM8921_MPP_BLOCK_START, 0),
+ .end = PM8921_IRQ_BLOCK_BIT(PM8921_MPP_BLOCK_START, 0)
+ + PM8921_NR_MPPS - 1,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct mfd_cell mpp_cell __devinitdata = {
+ .name = PM8XXX_MPP_DEV_NAME,
+ .id = -1,
+ .resources = mpp_cell_resources,
+ .num_resources = ARRAY_SIZE(mpp_cell_resources),
+};
+
static int __devinit pm8921_add_subdevices(const struct pm8921_platform_data
*pdata,
struct pm8921 *pmic,
@@ -131,6 +149,19 @@ static int __devinit pm8921_add_subdevices(const struct pm8921_platform_data
}
}
+ if (pdata->mpp_pdata) {
+ pdata->mpp_pdata->core_data.nmpps = PM8921_NR_MPPS;
+ pdata->mpp_pdata->core_data.base_addr = REG_MPP_BASE;
+ mpp_cell.platform_data = pdata->mpp_pdata;
+ mpp_cell.data_size = sizeof(struct pm8xxx_mpp_platform_data);
+ ret = mfd_add_devices(pmic->dev, 0, &mpp_cell, 1, NULL,
+ irq_base);
+ if (ret) {
+ pr_err("Failed to add mpp subdevice ret=%d\n", ret);
+ goto bail;
+ }
+ }
+
return 0;
bail:
if (pmic->irq_chip) {
diff --git a/include/linux/mfd/pm8xxx/mpp.h b/include/linux/mfd/pm8xxx/mpp.h
new file mode 100644
index 0000000..c779760
--- /dev/null
+++ b/include/linux/mfd/pm8xxx/mpp.h
@@ -0,0 +1,233 @@
+/* Copyright (c) 2011, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __PM8XXX_MPP_H
+#define __PM8XXX_MPP_H
+
+#include <linux/errno.h>
+
+#define PM8XXX_MPP_DEV_NAME "pm8xxx-mpp"
+
+struct pm8xxx_mpp_core_data {
+ int base_addr;
+ int nmpps;
+};
+
+struct pm8xxx_mpp_platform_data {
+ struct pm8xxx_mpp_core_data core_data;
+ int mpp_base;
+};
+
+/* API */
+#if defined(CONFIG_MFD_PM8XXX_MPP) || defined(CONFIG_MFD_PM8XXX_MPP_MODULE)
+
+/**
+ * pm8xxx_mpp_config() - configure control options of a multi-purpose pin (MPP)
+ * @mpp: global GPIO number corresponding to the MPP
+ * @type: MPP type which determines the overall MPP function (i.e. digital
+ * in/out/bi, analog in/out, current sink, or test). It should be
+ * set to the value of one of PM8XXX_MPP_TYPE_D_*.
+ * @level: meaning depends upon MPP type specified
+ * @control: meaning depends upon MPP type specified
+ * Context: can sleep
+ *
+ * RETURNS: an appropriate -ERRNO error value on error, or zero for success.
+ *
+ * Usage of level argument:
+ * 1. type = PM8XXX_MPP_TYPE_D_INPUT, PM8XXX_MPP_TYPE_D_OUTPUT,
+ * PM8XXX_MPP_TYPE_D_BI_DIR, or PM8XXX_MPP_TYPE_DTEST_OUTPUT -
+ *
+ * level specifies that digital logic level to use for the MPP. It should
+ * be set to the value of one of PM8XXX_MPP_DIG_LEVEL_*. Actual regulator
+ * connections for these level choices are PMIC chip specific.
+ *
+ * 2. type = PM8XXX_MPP_TYPE_A_INPUT -
+ *
+ * level specifies where in the PMIC chip the analog input value should
+ * be routed to. It should be set to the value of one of
+ * PM8XXX_MPP_AIN_AMUX_*.
+ *
+ * 3. type = PM8XXX_MPP_TYPE_A_OUTPUT -
+ *
+ * level specifies the output analog voltage reference level. It should
+ * be set to the value of one of PM8XXX_MPP_AOUT_LVL_*.
+ *
+ * 4. type = PM8XXX_MPP_TYPE_SINK or PM8XXX_MPP_TYPE_DTEST_SINK -
+ *
+ * level specifies the output current level. It should be set to the value
+ * of one of PM8XXX_MPP_CS_OUT_*.
+ *
+ * Usage of control argument:
+ * 1. type = PM8XXX_MPP_TYPE_D_INPUT -
+ *
+ * control specifies how the digital input should be routed in the chip.
+ * It should be set to the value of one of PM8XXX_MPP_DIN_TO_*.
+ *
+ * 2. type = PM8XXX_MPP_TYPE_D_OUTPUT -
+ *
+ * control specifies the digital output value. It should be set to the
+ * value of one of PM8XXX_MPP_DOUT_CTRL_*.
+ *
+ * 3. type = PM8XXX_MPP_TYPE_D_BI_DIR -
+ *
+ * control specifies the pullup resistor value. It should be set to the
+ * value of one of PM8XXX_MPP_BI_PULLUP_*.
+ *
+ * 4. type = PM8XXX_MPP_TYPE_A_INPUT -
+ *
+ * control is unused; a value of 0 is sufficient.
+ *
+ * 5. type = PM8XXX_MPP_TYPE_A_OUTPUT -
+ *
+ * control specifies if analog output is enabled. It should be set to the
+ * value of one of PM8XXX_MPP_AOUT_CTRL_*.
+ *
+ * 6. type = PM8XXX_MPP_TYPE_SINK -
+ *
+ * control specifies if current sinking is enabled. It should be set to
+ * the value of one of PM8XXX_MPP_CS_CTRL_*.
+ *
+ * 7. type = PM8XXX_MPP_TYPE_DTEST_SINK -
+ *
+ * control specifies if current sinking is enabled. It should be set to
+ * the value of one of PM8XXX_MPP_DTEST_CS_CTRL_*.
+ *
+ * 8. type = PM8XXX_MPP_TYPE_DTEST_OUTPUT -
+ *
+ * control specifies which DTEST bus value to output. It should be set to
+ * the value of one of PM8XXX_MPP_DTEST_*.
+ */
+int pm8xxx_mpp_config(unsigned mpp, unsigned type, unsigned level,
+ unsigned control);
+
+#else
+
+static inline int pm8xxx_mpp_config(unsigned mpp, unsigned type, unsigned level,
+ unsigned control)
+{
+ return -ENXIO;
+}
+
+#endif
+
+/* MPP Type: type */
+#define PM8XXX_MPP_TYPE_D_INPUT 0
+#define PM8XXX_MPP_TYPE_D_OUTPUT 1
+#define PM8XXX_MPP_TYPE_D_BI_DIR 2
+#define PM8XXX_MPP_TYPE_A_INPUT 3
+#define PM8XXX_MPP_TYPE_A_OUTPUT 4
+#define PM8XXX_MPP_TYPE_SINK 5
+#define PM8XXX_MPP_TYPE_DTEST_SINK 6
+#define PM8XXX_MPP_TYPE_DTEST_OUTPUT 7
+
+/* Digital Input/Output: level */
+#define PM8XXX_MPP_DIG_LEVEL_VIO_0 0
+#define PM8XXX_MPP_DIG_LEVEL_VIO_1 1
+#define PM8XXX_MPP_DIG_LEVEL_VIO_2 2
+#define PM8XXX_MPP_DIG_LEVEL_VIO_3 3
+#define PM8XXX_MPP_DIG_LEVEL_VIO_4 4
+#define PM8XXX_MPP_DIG_LEVEL_VIO_5 5
+#define PM8XXX_MPP_DIG_LEVEL_VIO_6 6
+#define PM8XXX_MPP_DIG_LEVEL_VIO_7 7
+
+/* Digital Input/Output: level [PM8058] */
+#define PM8058_MPP_DIG_LEVEL_VPH 0
+#define PM8058_MPP_DIG_LEVEL_S3 1
+#define PM8058_MPP_DIG_LEVEL_L2 2
+#define PM8058_MPP_DIG_LEVEL_L3 3
+
+/* Digital Input/Output: level [PM8901] */
+#define PM8901_MPP_DIG_LEVEL_MSMIO 0
+#define PM8901_MPP_DIG_LEVEL_DIG 1
+#define PM8901_MPP_DIG_LEVEL_L5 2
+#define PM8901_MPP_DIG_LEVEL_S4 3
+#define PM8901_MPP_DIG_LEVEL_VPH 4
+
+/* Digital Input/Output: level [PM8921] */
+#define PM8921_MPP_DIG_LEVEL_S4 1
+#define PM8921_MPP_DIG_LEVEL_L15 3
+#define PM8921_MPP_DIG_LEVEL_L17 4
+#define PM8921_MPP_DIG_LEVEL_VPH 7
+
+/* Digital Input: control */
+#define PM8XXX_MPP_DIN_TO_INT 0
+#define PM8XXX_MPP_DIN_TO_DBUS1 1
+#define PM8XXX_MPP_DIN_TO_DBUS2 2
+#define PM8XXX_MPP_DIN_TO_DBUS3 3
+
+/* Digital Output: control */
+#define PM8XXX_MPP_DOUT_CTRL_LOW 0
+#define PM8XXX_MPP_DOUT_CTRL_HIGH 1
+#define PM8XXX_MPP_DOUT_CTRL_MPP 2
+#define PM8XXX_MPP_DOUT_CTRL_INV_MPP 3
+
+/* Bidirectional: control */
+#define PM8XXX_MPP_BI_PULLUP_1KOHM 0
+#define PM8XXX_MPP_BI_PULLUP_OPEN 1
+#define PM8XXX_MPP_BI_PULLUP_10KOHM 2
+#define PM8XXX_MPP_BI_PULLUP_30KOHM 3
+
+/* Analog Input: level */
+#define PM8XXX_MPP_AIN_AMUX_CH5 0
+#define PM8XXX_MPP_AIN_AMUX_CH6 1
+#define PM8XXX_MPP_AIN_AMUX_CH7 2
+#define PM8XXX_MPP_AIN_AMUX_CH8 3
+#define PM8XXX_MPP_AIN_AMUX_CH9 4
+#define PM8XXX_MPP_AIN_AMUX_ABUS1 5
+#define PM8XXX_MPP_AIN_AMUX_ABUS2 6
+#define PM8XXX_MPP_AIN_AMUX_ABUS3 7
+
+/* Analog Output: level */
+#define PM8XXX_MPP_AOUT_LVL_1V25 0
+#define PM8XXX_MPP_AOUT_LVL_1V25_2 1
+#define PM8XXX_MPP_AOUT_LVL_0V625 2
+#define PM8XXX_MPP_AOUT_LVL_0V3125 3
+#define PM8XXX_MPP_AOUT_LVL_MPP 4
+#define PM8XXX_MPP_AOUT_LVL_ABUS1 5
+#define PM8XXX_MPP_AOUT_LVL_ABUS2 6
+#define PM8XXX_MPP_AOUT_LVL_ABUS3 7
+
+/* Analog Output: control */
+#define PM8XXX_MPP_AOUT_CTRL_DISABLE 0
+#define PM8XXX_MPP_AOUT_CTRL_ENABLE 1
+#define PM8XXX_MPP_AOUT_CTRL_MPP_HIGH_EN 2
+#define PM8XXX_MPP_AOUT_CTRL_MPP_LOW_EN 3
+
+/* Current Sink: level */
+#define PM8XXX_MPP_CS_OUT_5MA 0
+#define PM8XXX_MPP_CS_OUT_10MA 1
+#define PM8XXX_MPP_CS_OUT_15MA 2
+#define PM8XXX_MPP_CS_OUT_20MA 3
+#define PM8XXX_MPP_CS_OUT_25MA 4
+#define PM8XXX_MPP_CS_OUT_30MA 5
+#define PM8XXX_MPP_CS_OUT_35MA 6
+#define PM8XXX_MPP_CS_OUT_40MA 7
+
+/* Current Sink: control */
+#define PM8XXX_MPP_CS_CTRL_DISABLE 0
+#define PM8XXX_MPP_CS_CTRL_ENABLE 1
+#define PM8XXX_MPP_CS_CTRL_MPP_HIGH_EN 2
+#define PM8XXX_MPP_CS_CTRL_MPP_LOW_EN 3
+
+/* DTEST Current Sink: control */
+#define PM8XXX_MPP_DTEST_CS_CTRL_EN1 0
+#define PM8XXX_MPP_DTEST_CS_CTRL_EN2 1
+#define PM8XXX_MPP_DTEST_CS_CTRL_EN3 2
+#define PM8XXX_MPP_DTEST_CS_CTRL_EN4 3
+
+/* DTEST Digital Output: control */
+#define PM8XXX_MPP_DTEST_DBUS1 0
+#define PM8XXX_MPP_DTEST_DBUS2 1
+#define PM8XXX_MPP_DTEST_DBUS3 2
+#define PM8XXX_MPP_DTEST_DBUS4 3
+
+#endif
diff --git a/include/linux/mfd/pm8xxx/pm8921.h b/include/linux/mfd/pm8xxx/pm8921.h
index def8c31..19cffb2 100644
--- a/include/linux/mfd/pm8xxx/pm8921.h
+++ b/include/linux/mfd/pm8xxx/pm8921.h
@@ -21,22 +21,29 @@
#include <linux/device.h>
#include <linux/mfd/pm8xxx/irq.h>
#include <linux/mfd/pm8xxx/gpio.h>
+#include <linux/mfd/pm8xxx/mpp.h>
#define PM8921_NR_IRQS 256
#define PM8921_NR_GPIOS 44
+#define PM8921_NR_MPPS 12
+
#define PM8921_GPIO_BLOCK_START 24
+#define PM8921_MPP_BLOCK_START 16
#define PM8921_IRQ_BLOCK_BIT(block, bit) ((block) * 8 + (bit))
-/* GPIOs [1,N] */
+/* GPIOs and MPPs [1,N] */
#define PM8921_GPIO_IRQ(base, gpio) ((base) + \
PM8921_IRQ_BLOCK_BIT(PM8921_GPIO_BLOCK_START, (gpio)-1))
+#define PM8921_MPP_IRQ(base, mpp) ((base) + \
+ PM8921_IRQ_BLOCK_BIT(PM8921_MPP_BLOCK_START, (mpp)-1))
struct pm8921_platform_data {
int irq_base;
struct pm8xxx_irq_platform_data *irq_pdata;
struct pm8xxx_gpio_platform_data *gpio_pdata;
+ struct pm8xxx_mpp_platform_data *mpp_pdata;
};
#endif
--
1.7.1
Sent by an employee of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
^ permalink raw reply related [flat|nested] 10+ messages in thread* Re: [PM8921 MFD V4 4/6] mfd: pm8xxx-mpp: Add pm8xxx MPP driver
2011-03-18 4:21 ` [PM8921 MFD V4 4/6] mfd: pm8xxx-mpp: Add pm8xxx MPP driver adharmap
@ 2011-03-22 18:45 ` Abhijeet Dharmapurikar
0 siblings, 0 replies; 10+ messages in thread
From: Abhijeet Dharmapurikar @ 2011-03-22 18:45 UTC (permalink / raw)
To: davidb, dwalker, Grant Likely
Cc: David Collins, Bryan Huntsman, Samuel Ortiz, linux-kernel,
linux-arm-msm, linux-arm-msm-owner, linux-arm-kernel, Mark Brown,
Linus Walleij, Thomas Glexiner, Greg Kroah-Hartman
Grant Likely,
Can you please review/ack this one?
Abhijeet
adharmap@codeaurora.org wrote:
> From: David Collins <collinsd@codeaurora.org>
>
> Add support for multi-purpose pins (MPPs) on Qualcomm PM8xxx
> PMIC chips.
>
> PM8xxx MPPs can be configured as digital or analog inputs or
> outputs, current sinks, or buffers.
>
> Note that mpp pins appear as gpio lines to the kernel. However they
> are implemented separately from the pmic's gpio driver as
> mpps have different configuration attributes and have different
> register controls than the pmic's gpio controller. Basically they are
> different set of pins.
>
> Signed-off-by: David Collins <collinsd@codeaurora.org>
> ---
> drivers/gpio/Kconfig | 8 +
> drivers/gpio/Makefile | 1 +
> drivers/gpio/pm8xxx-mpp.c | 326 +++++++++++++++++++++++++++++++++++++
> drivers/mfd/pm8921-core.c | 31 ++++
> include/linux/mfd/pm8xxx/mpp.h | 233 ++++++++++++++++++++++++++
> include/linux/mfd/pm8xxx/pm8921.h | 9 +-
> 6 files changed, 607 insertions(+), 1 deletions(-)
> create mode 100644 drivers/gpio/pm8xxx-mpp.c
> create mode 100644 include/linux/mfd/pm8xxx/mpp.h
>
> diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
> index 52c233e..7ada3b1 100644
> --- a/drivers/gpio/Kconfig
> +++ b/drivers/gpio/Kconfig
> @@ -419,4 +419,12 @@ config GPIO_PM8XXX
> This option enables support for on-chip GPIO found on Qualcomm PM8xxx
> PMICs.
>
> +config MFD_PM8XXX_MPP
> + tristate "Support for Qualcomm PM8xxx MPP features"
> + depends on MFD_PM8XXX
> + default y if MFD_PM8XXX
> + help
> + This is the multi-purpose pin (MPP) driver for Qualcomm PM 8xxx PMIC
> + chips.
> +
> endif
> diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
> index 10efe6c..0452caf 100644
> --- a/drivers/gpio/Makefile
> +++ b/drivers/gpio/Makefile
> @@ -43,3 +43,4 @@ obj-$(CONFIG_GPIO_SX150X) += sx150x.o
> obj-$(CONFIG_GPIO_VX855) += vx855_gpio.o
> obj-$(CONFIG_GPIO_ML_IOH) += ml_ioh_gpio.o
> obj-$(CONFIG_GPIO_PM8XXX) += pm8xxx-gpio.o
> +obj-$(CONFIG_MFD_PM8XXX_MPP) += pm8xxx-mpp.o
> diff --git a/drivers/gpio/pm8xxx-mpp.c b/drivers/gpio/pm8xxx-mpp.c
> new file mode 100644
> index 0000000..6e90e91
> --- /dev/null
> +++ b/drivers/gpio/pm8xxx-mpp.c
> @@ -0,0 +1,326 @@
> +/*
> + * Qualcomm PM8XXX Multi-Purpose Pin (MPP) driver
> + *
> + * Copyright (c) 2011, Code Aurora Forum. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#define pr_fmt(fmt) "%s: " fmt, __func__
> +
> +#include <linux/platform_device.h>
> +#include <linux/gpio.h>
> +#include <linux/seq_file.h>
> +#include <linux/slab.h>
> +#include <linux/spinlock.h>
> +#include <linux/mfd/pm8xxx/core.h>
> +#include <linux/mfd/pm8xxx/mpp.h>
> +
> +/* MPP Type */
> +#define PM8XXX_MPP_TYPE_MASK 0xE0
> +#define PM8XXX_MPP_TYPE_SHIFT 5
> +
> +/* MPP Config Level */
> +#define PM8XXX_MPP_CONFIG_LVL_MASK 0x1C
> +#define PM8XXX_MPP_CONFIG_LVL_SHIFT 2
> +
> +/* MPP Config Control */
> +#define PM8XXX_MPP_CONFIG_CTRL_MASK 0x03
> +#define PM8XXX_MPP_CONFIG_CTRL_SHIFT 0
> +
> +struct pm8xxx_mpp_chip {
> + struct list_head link;
> + struct gpio_chip gpio_chip;
> + spinlock_t pm_lock;
> + u8 *ctrl_reg;
> + int mpp_base;
> + int irq_base;
> + int nmpps;
> + u16 base_addr;
> +};
> +
> +static LIST_HEAD(pm8xxx_mpp_chips);
> +static DEFINE_MUTEX(pm8xxx_mpp_chips_lock);
> +
> +static int pm8xxx_mpp_write(struct pm8xxx_mpp_chip *mpp_chip, u16 offset,
> + u8 val, u8 mask)
> +{
> + u8 reg;
> + int rc;
> + unsigned long flags;
> +
> + spin_lock_irqsave(&mpp_chip->pm_lock, flags);
> +
> + reg = (mpp_chip->ctrl_reg[offset] & ~mask) | (val & mask);
> + rc = pm8xxx_writeb(mpp_chip->gpio_chip.dev->parent,
> + mpp_chip->base_addr + offset, reg);
> + if (!rc)
> + mpp_chip->ctrl_reg[offset] = reg;
> +
> + spin_unlock_irqrestore(&mpp_chip->pm_lock, flags);
> +
> + return rc;
> +}
> +
> +static int pm8xxx_mpp_to_irq(struct gpio_chip *chip, unsigned offset)
> +{
> + struct pm8xxx_mpp_chip *mpp_chip = dev_get_drvdata(chip->dev);
> +
> + return mpp_chip->irq_base + offset;
> +}
> +
> +static int pm8xxx_mpp_get(struct gpio_chip *chip, unsigned offset)
> +{
> + struct pm8xxx_mpp_chip *mpp_chip = dev_get_drvdata(chip->dev);
> + int rc;
> +
> + if ((mpp_chip->ctrl_reg[offset] & PM8XXX_MPP_TYPE_MASK) >>
> + PM8XXX_MPP_TYPE_SHIFT == PM8XXX_MPP_TYPE_D_OUTPUT)
> + rc = mpp_chip->ctrl_reg[offset] & PM8XXX_MPP_CONFIG_CTRL_MASK;
> + else
> + rc = pm8xxx_read_irq_stat(mpp_chip->gpio_chip.dev->parent,
> + mpp_chip->irq_base + offset);
> +
> + return rc;
> +}
> +
> +static void pm8xxx_mpp_set(struct gpio_chip *chip, unsigned offset, int val)
> +{
> + struct pm8xxx_mpp_chip *mpp_chip = dev_get_drvdata(chip->dev);
> + u8 reg = val ? PM8XXX_MPP_DOUT_CTRL_HIGH : PM8XXX_MPP_DOUT_CTRL_LOW;
> + int rc;
> +
> + rc = pm8xxx_mpp_write(mpp_chip, offset, reg,
> + PM8XXX_MPP_CONFIG_CTRL_MASK);
> + if (rc)
> + pr_err("pm8xxx_mpp_write(): rc=%d\n", rc);
> +}
> +
> +static int pm8xxx_mpp_dir_input(struct gpio_chip *chip, unsigned offset)
> +{
> + struct pm8xxx_mpp_chip *mpp_chip = dev_get_drvdata(chip->dev);
> + int rc = pm8xxx_mpp_write(mpp_chip, offset,
> + PM8XXX_MPP_TYPE_D_INPUT << PM8XXX_MPP_TYPE_SHIFT,
> + PM8XXX_MPP_TYPE_MASK);
> +
> + if (rc)
> + pr_err("pm8xxx_mpp_write(): rc=%d\n", rc);
> + return rc;
> +}
> +
> +static int pm8xxx_mpp_dir_output(struct gpio_chip *chip,
> + unsigned offset, int val)
> +{
> + struct pm8xxx_mpp_chip *mpp_chip = dev_get_drvdata(chip->dev);
> + u8 reg = (PM8XXX_MPP_TYPE_D_OUTPUT << PM8XXX_MPP_TYPE_SHIFT) |
> + (val & PM8XXX_MPP_CONFIG_CTRL_MASK);
> + u8 mask = PM8XXX_MPP_TYPE_MASK | PM8XXX_MPP_CONFIG_CTRL_MASK;
> + int rc = pm8xxx_mpp_write(mpp_chip, offset, reg, mask);
> +
> + if (rc)
> + pr_err("pm8xxx_mpp_write(): rc=%d\n", rc);
> + return rc;
> +}
> +
> +static void pm8xxx_mpp_dbg_show(struct seq_file *s, struct gpio_chip *chip)
> +{
> + static const char * const ctype[] = { "d_in", "d_out", "bi_dir",
> + "a_in", "a_out", "sink",
> + "dtest_sink", "dtest_out"
> + };
> + struct pm8xxx_mpp_chip *mpp_chip = dev_get_drvdata(chip->dev);
> + u8 type, state;
> + const char *label;
> + int i;
> +
> + for (i = 0; i < mpp_chip->nmpps; i++) {
> + label = gpiochip_is_requested(chip, i);
> + type = (mpp_chip->ctrl_reg[i] & PM8XXX_MPP_TYPE_MASK) >>
> + PM8XXX_MPP_TYPE_SHIFT;
> + state = pm8xxx_mpp_get(chip, i);
> + seq_printf(s, "gpio-%-3d (%-12.12s) %-10.10s"
> + " %s 0x%02x\n",
> + chip->base + i,
> + label ? label : "--",
> + ctype[type],
> + state ? "hi" : "lo",
> + mpp_chip->ctrl_reg[i]);
> + }
> +}
> +
> +int pm8xxx_mpp_config(unsigned mpp, unsigned type, unsigned level,
> + unsigned control)
> +{
> + struct pm8xxx_mpp_chip *mpp_chip;
> + int rc, found = 0;
> + u8 config, mask;
> +
> + mutex_lock(&pm8xxx_mpp_chips_lock);
> + list_for_each_entry(mpp_chip, &pm8xxx_mpp_chips, link) {
> + if (mpp >= mpp_chip->mpp_base
> + && mpp < mpp_chip->mpp_base + mpp_chip->nmpps) {
> + found = 1;
> + break;
> + }
> + }
> + mutex_unlock(&pm8xxx_mpp_chips_lock);
> + if (!found) {
> + pr_err("called on mpp %d not handled by any pmic\n", mpp);
> + return -EINVAL;
> + }
> +
> + mask = PM8XXX_MPP_TYPE_MASK | PM8XXX_MPP_CONFIG_LVL_MASK |
> + PM8XXX_MPP_CONFIG_CTRL_MASK;
> + config = (type << PM8XXX_MPP_TYPE_SHIFT) & PM8XXX_MPP_TYPE_MASK;
> + config |= (level << PM8XXX_MPP_CONFIG_LVL_SHIFT) &
> + PM8XXX_MPP_CONFIG_LVL_MASK;
> + config |= control & PM8XXX_MPP_CONFIG_CTRL_MASK;
> +
> + rc = pm8xxx_mpp_write(mpp_chip, mpp - mpp_chip->mpp_base, config, mask);
> +
> + if (rc)
> + pr_err("pm8xxx_mpp_write(): rc=%d\n", rc);
> +
> + return rc;
> +}
> +EXPORT_SYMBOL_GPL(pm8xxx_mpp_config);
> +
> +static int __devinit pm8xxx_mpp_reg_init(struct pm8xxx_mpp_chip *mpp_chip)
> +{
> + int rc, i;
> +
> + for (i = 0; i < mpp_chip->nmpps; i++) {
> + rc = pm8xxx_readb(mpp_chip->gpio_chip.dev->parent,
> + mpp_chip->base_addr + i,
> + &mpp_chip->ctrl_reg[i]);
> + if (rc) {
> + pr_err("failed to read register 0x%x rc=%d\n",
> + mpp_chip->base_addr + i, rc);
> + return rc;
> + }
> + }
> + return 0;
> +}
> +
> +static int __devinit pm8xxx_mpp_probe(struct platform_device *pdev)
> +{
> + int rc;
> + const struct pm8xxx_mpp_platform_data *pdata = pdev->dev.platform_data;
> + struct pm8xxx_mpp_chip *mpp_chip;
> +
> + if (!pdata) {
> + pr_err("missing platform data\n");
> + return -EINVAL;
> + }
> +
> + mpp_chip = kzalloc(sizeof(struct pm8xxx_mpp_chip), GFP_KERNEL);
> + if (!mpp_chip) {
> + pr_err("Cannot allocate %d bytes\n",
> + sizeof(struct pm8xxx_mpp_chip));
> + return -ENOMEM;
> + }
> +
> + mpp_chip->ctrl_reg = kzalloc(pdata->core_data.nmpps, GFP_KERNEL);
> + if (!mpp_chip->ctrl_reg) {
> + pr_err("Cannot allocate %d bytes\n", pdata->core_data.nmpps);
> + rc = -ENOMEM;
> + goto free_mpp_chip;
> + }
> +
> + spin_lock_init(&mpp_chip->pm_lock);
> +
> + mpp_chip->gpio_chip.label = PM8XXX_MPP_DEV_NAME;
> + mpp_chip->gpio_chip.direction_input = pm8xxx_mpp_dir_input;
> + mpp_chip->gpio_chip.direction_output = pm8xxx_mpp_dir_output;
> + mpp_chip->gpio_chip.to_irq = pm8xxx_mpp_to_irq;
> + mpp_chip->gpio_chip.get = pm8xxx_mpp_get;
> + mpp_chip->gpio_chip.set = pm8xxx_mpp_set;
> + mpp_chip->gpio_chip.dbg_show = pm8xxx_mpp_dbg_show;
> + mpp_chip->gpio_chip.ngpio = pdata->core_data.nmpps;
> + mpp_chip->gpio_chip.can_sleep = 1;
> + mpp_chip->gpio_chip.dev = &pdev->dev;
> + mpp_chip->gpio_chip.base = pdata->mpp_base;
> + mpp_chip->irq_base = platform_get_irq(pdev, 0);
> + mpp_chip->mpp_base = pdata->mpp_base;
> + mpp_chip->base_addr = pdata->core_data.base_addr;
> + mpp_chip->nmpps = pdata->core_data.nmpps;
> +
> + mutex_unlock(&pm8xxx_mpp_chips_lock);
> + list_add(&mpp_chip->link, &pm8xxx_mpp_chips);
> + mutex_lock(&pm8xxx_mpp_chips_lock);
> +
> + platform_set_drvdata(pdev, mpp_chip);
> +
> + rc = gpiochip_add(&mpp_chip->gpio_chip);
> + if (rc) {
> + pr_err("gpiochip_add failed, rc=%d\n", rc);
> + goto reset_drvdata;
> + }
> +
> + rc = pm8xxx_mpp_reg_init(mpp_chip);
> + if (rc) {
> + pr_err("failed to read MPP ctrl registers, rc=%d\n", rc);
> + goto remove_chip;
> + }
> +
> + return 0;
> +
> +remove_chip:
> + if (gpiochip_remove(&mpp_chip->gpio_chip))
> + pr_err("failed to remove gpio chip\n");
> +reset_drvdata:
> + platform_set_drvdata(pdev, NULL);
> + mutex_destroy(&mpp_chip->pm_lock);
> +free_mpp_chip:
> + kfree(mpp_chip);
> + return rc;
> +}
> +
> +static int __devexit pm8xxx_mpp_remove(struct platform_device *pdev)
> +{
> + struct pm8xxx_mpp_chip *mpp_chip = platform_get_drvdata(pdev);
> +
> + mutex_lock(&pm8xxx_mpp_chips_lock);
> + list_del(&mpp_chip->link);
> + mutex_unlock(&pm8xxx_mpp_chips_lock);
> + platform_set_drvdata(pdev, NULL);
> + if (gpiochip_remove(&mpp_chip->gpio_chip))
> + pr_err("failed to remove gpio chip\n");
> + kfree(mpp_chip->ctrl_reg);
> + kfree(mpp_chip);
> +
> + return 0;
> +}
> +
> +static struct platform_driver pm8xxx_mpp_driver = {
> + .probe = pm8xxx_mpp_probe,
> + .remove = __devexit_p(pm8xxx_mpp_remove),
> + .driver = {
> + .name = PM8XXX_MPP_DEV_NAME,
> + .owner = THIS_MODULE,
> + },
> +};
> +
> +static int __init pm8xxx_mpp_init(void)
> +{
> + return platform_driver_register(&pm8xxx_mpp_driver);
> +}
> +subsys_initcall(pm8xxx_mpp_init);
> +
> +static void __exit pm8xxx_mpp_exit(void)
> +{
> + platform_driver_unregister(&pm8xxx_mpp_driver);
> +}
> +module_exit(pm8xxx_mpp_exit);
> +
> +MODULE_LICENSE("GPL v2");
> +MODULE_DESCRIPTION("PM8XXX MPP driver");
> +MODULE_VERSION("1.0");
> +MODULE_ALIAS("platform:" PM8XXX_MPP_DEV_NAME);
> diff --git a/drivers/mfd/pm8921-core.c b/drivers/mfd/pm8921-core.c
> index 3932bee..d0a991c 100644
> --- a/drivers/mfd/pm8921-core.c
> +++ b/drivers/mfd/pm8921-core.c
> @@ -25,6 +25,8 @@
> #define REG_HWREV 0x002 /* PMIC4 revision */
> #define REG_HWREV_2 0x0E8 /* PMIC4 revision 2 */
>
> +#define REG_MPP_BASE 0x050
> +
> struct pm8921 {
> struct device *dev;
> struct pm_irq_chip *irq_chip;
> @@ -96,6 +98,22 @@ static struct mfd_cell gpio_cell __devinitdata = {
> .num_resources = ARRAY_SIZE(gpio_cell_resources),
> };
>
> +static const struct resource mpp_cell_resources[] __devinitconst = {
> + {
> + .start = PM8921_IRQ_BLOCK_BIT(PM8921_MPP_BLOCK_START, 0),
> + .end = PM8921_IRQ_BLOCK_BIT(PM8921_MPP_BLOCK_START, 0)
> + + PM8921_NR_MPPS - 1,
> + .flags = IORESOURCE_IRQ,
> + },
> +};
> +
> +static struct mfd_cell mpp_cell __devinitdata = {
> + .name = PM8XXX_MPP_DEV_NAME,
> + .id = -1,
> + .resources = mpp_cell_resources,
> + .num_resources = ARRAY_SIZE(mpp_cell_resources),
> +};
> +
> static int __devinit pm8921_add_subdevices(const struct pm8921_platform_data
> *pdata,
> struct pm8921 *pmic,
> @@ -131,6 +149,19 @@ static int __devinit pm8921_add_subdevices(const struct pm8921_platform_data
> }
> }
>
> + if (pdata->mpp_pdata) {
> + pdata->mpp_pdata->core_data.nmpps = PM8921_NR_MPPS;
> + pdata->mpp_pdata->core_data.base_addr = REG_MPP_BASE;
> + mpp_cell.platform_data = pdata->mpp_pdata;
> + mpp_cell.data_size = sizeof(struct pm8xxx_mpp_platform_data);
> + ret = mfd_add_devices(pmic->dev, 0, &mpp_cell, 1, NULL,
> + irq_base);
> + if (ret) {
> + pr_err("Failed to add mpp subdevice ret=%d\n", ret);
> + goto bail;
> + }
> + }
> +
> return 0;
> bail:
> if (pmic->irq_chip) {
> diff --git a/include/linux/mfd/pm8xxx/mpp.h b/include/linux/mfd/pm8xxx/mpp.h
> new file mode 100644
> index 0000000..c779760
> --- /dev/null
> +++ b/include/linux/mfd/pm8xxx/mpp.h
> @@ -0,0 +1,233 @@
> +/* Copyright (c) 2011, Code Aurora Forum. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#ifndef __PM8XXX_MPP_H
> +#define __PM8XXX_MPP_H
> +
> +#include <linux/errno.h>
> +
> +#define PM8XXX_MPP_DEV_NAME "pm8xxx-mpp"
> +
> +struct pm8xxx_mpp_core_data {
> + int base_addr;
> + int nmpps;
> +};
> +
> +struct pm8xxx_mpp_platform_data {
> + struct pm8xxx_mpp_core_data core_data;
> + int mpp_base;
> +};
> +
> +/* API */
> +#if defined(CONFIG_MFD_PM8XXX_MPP) || defined(CONFIG_MFD_PM8XXX_MPP_MODULE)
> +
> +/**
> + * pm8xxx_mpp_config() - configure control options of a multi-purpose pin (MPP)
> + * @mpp: global GPIO number corresponding to the MPP
> + * @type: MPP type which determines the overall MPP function (i.e. digital
> + * in/out/bi, analog in/out, current sink, or test). It should be
> + * set to the value of one of PM8XXX_MPP_TYPE_D_*.
> + * @level: meaning depends upon MPP type specified
> + * @control: meaning depends upon MPP type specified
> + * Context: can sleep
> + *
> + * RETURNS: an appropriate -ERRNO error value on error, or zero for success.
> + *
> + * Usage of level argument:
> + * 1. type = PM8XXX_MPP_TYPE_D_INPUT, PM8XXX_MPP_TYPE_D_OUTPUT,
> + * PM8XXX_MPP_TYPE_D_BI_DIR, or PM8XXX_MPP_TYPE_DTEST_OUTPUT -
> + *
> + * level specifies that digital logic level to use for the MPP. It should
> + * be set to the value of one of PM8XXX_MPP_DIG_LEVEL_*. Actual regulator
> + * connections for these level choices are PMIC chip specific.
> + *
> + * 2. type = PM8XXX_MPP_TYPE_A_INPUT -
> + *
> + * level specifies where in the PMIC chip the analog input value should
> + * be routed to. It should be set to the value of one of
> + * PM8XXX_MPP_AIN_AMUX_*.
> + *
> + * 3. type = PM8XXX_MPP_TYPE_A_OUTPUT -
> + *
> + * level specifies the output analog voltage reference level. It should
> + * be set to the value of one of PM8XXX_MPP_AOUT_LVL_*.
> + *
> + * 4. type = PM8XXX_MPP_TYPE_SINK or PM8XXX_MPP_TYPE_DTEST_SINK -
> + *
> + * level specifies the output current level. It should be set to the value
> + * of one of PM8XXX_MPP_CS_OUT_*.
> + *
> + * Usage of control argument:
> + * 1. type = PM8XXX_MPP_TYPE_D_INPUT -
> + *
> + * control specifies how the digital input should be routed in the chip.
> + * It should be set to the value of one of PM8XXX_MPP_DIN_TO_*.
> + *
> + * 2. type = PM8XXX_MPP_TYPE_D_OUTPUT -
> + *
> + * control specifies the digital output value. It should be set to the
> + * value of one of PM8XXX_MPP_DOUT_CTRL_*.
> + *
> + * 3. type = PM8XXX_MPP_TYPE_D_BI_DIR -
> + *
> + * control specifies the pullup resistor value. It should be set to the
> + * value of one of PM8XXX_MPP_BI_PULLUP_*.
> + *
> + * 4. type = PM8XXX_MPP_TYPE_A_INPUT -
> + *
> + * control is unused; a value of 0 is sufficient.
> + *
> + * 5. type = PM8XXX_MPP_TYPE_A_OUTPUT -
> + *
> + * control specifies if analog output is enabled. It should be set to the
> + * value of one of PM8XXX_MPP_AOUT_CTRL_*.
> + *
> + * 6. type = PM8XXX_MPP_TYPE_SINK -
> + *
> + * control specifies if current sinking is enabled. It should be set to
> + * the value of one of PM8XXX_MPP_CS_CTRL_*.
> + *
> + * 7. type = PM8XXX_MPP_TYPE_DTEST_SINK -
> + *
> + * control specifies if current sinking is enabled. It should be set to
> + * the value of one of PM8XXX_MPP_DTEST_CS_CTRL_*.
> + *
> + * 8. type = PM8XXX_MPP_TYPE_DTEST_OUTPUT -
> + *
> + * control specifies which DTEST bus value to output. It should be set to
> + * the value of one of PM8XXX_MPP_DTEST_*.
> + */
> +int pm8xxx_mpp_config(unsigned mpp, unsigned type, unsigned level,
> + unsigned control);
> +
> +#else
> +
> +static inline int pm8xxx_mpp_config(unsigned mpp, unsigned type, unsigned level,
> + unsigned control)
> +{
> + return -ENXIO;
> +}
> +
> +#endif
> +
> +/* MPP Type: type */
> +#define PM8XXX_MPP_TYPE_D_INPUT 0
> +#define PM8XXX_MPP_TYPE_D_OUTPUT 1
> +#define PM8XXX_MPP_TYPE_D_BI_DIR 2
> +#define PM8XXX_MPP_TYPE_A_INPUT 3
> +#define PM8XXX_MPP_TYPE_A_OUTPUT 4
> +#define PM8XXX_MPP_TYPE_SINK 5
> +#define PM8XXX_MPP_TYPE_DTEST_SINK 6
> +#define PM8XXX_MPP_TYPE_DTEST_OUTPUT 7
> +
> +/* Digital Input/Output: level */
> +#define PM8XXX_MPP_DIG_LEVEL_VIO_0 0
> +#define PM8XXX_MPP_DIG_LEVEL_VIO_1 1
> +#define PM8XXX_MPP_DIG_LEVEL_VIO_2 2
> +#define PM8XXX_MPP_DIG_LEVEL_VIO_3 3
> +#define PM8XXX_MPP_DIG_LEVEL_VIO_4 4
> +#define PM8XXX_MPP_DIG_LEVEL_VIO_5 5
> +#define PM8XXX_MPP_DIG_LEVEL_VIO_6 6
> +#define PM8XXX_MPP_DIG_LEVEL_VIO_7 7
> +
> +/* Digital Input/Output: level [PM8058] */
> +#define PM8058_MPP_DIG_LEVEL_VPH 0
> +#define PM8058_MPP_DIG_LEVEL_S3 1
> +#define PM8058_MPP_DIG_LEVEL_L2 2
> +#define PM8058_MPP_DIG_LEVEL_L3 3
> +
> +/* Digital Input/Output: level [PM8901] */
> +#define PM8901_MPP_DIG_LEVEL_MSMIO 0
> +#define PM8901_MPP_DIG_LEVEL_DIG 1
> +#define PM8901_MPP_DIG_LEVEL_L5 2
> +#define PM8901_MPP_DIG_LEVEL_S4 3
> +#define PM8901_MPP_DIG_LEVEL_VPH 4
> +
> +/* Digital Input/Output: level [PM8921] */
> +#define PM8921_MPP_DIG_LEVEL_S4 1
> +#define PM8921_MPP_DIG_LEVEL_L15 3
> +#define PM8921_MPP_DIG_LEVEL_L17 4
> +#define PM8921_MPP_DIG_LEVEL_VPH 7
> +
> +/* Digital Input: control */
> +#define PM8XXX_MPP_DIN_TO_INT 0
> +#define PM8XXX_MPP_DIN_TO_DBUS1 1
> +#define PM8XXX_MPP_DIN_TO_DBUS2 2
> +#define PM8XXX_MPP_DIN_TO_DBUS3 3
> +
> +/* Digital Output: control */
> +#define PM8XXX_MPP_DOUT_CTRL_LOW 0
> +#define PM8XXX_MPP_DOUT_CTRL_HIGH 1
> +#define PM8XXX_MPP_DOUT_CTRL_MPP 2
> +#define PM8XXX_MPP_DOUT_CTRL_INV_MPP 3
> +
> +/* Bidirectional: control */
> +#define PM8XXX_MPP_BI_PULLUP_1KOHM 0
> +#define PM8XXX_MPP_BI_PULLUP_OPEN 1
> +#define PM8XXX_MPP_BI_PULLUP_10KOHM 2
> +#define PM8XXX_MPP_BI_PULLUP_30KOHM 3
> +
> +/* Analog Input: level */
> +#define PM8XXX_MPP_AIN_AMUX_CH5 0
> +#define PM8XXX_MPP_AIN_AMUX_CH6 1
> +#define PM8XXX_MPP_AIN_AMUX_CH7 2
> +#define PM8XXX_MPP_AIN_AMUX_CH8 3
> +#define PM8XXX_MPP_AIN_AMUX_CH9 4
> +#define PM8XXX_MPP_AIN_AMUX_ABUS1 5
> +#define PM8XXX_MPP_AIN_AMUX_ABUS2 6
> +#define PM8XXX_MPP_AIN_AMUX_ABUS3 7
> +
> +/* Analog Output: level */
> +#define PM8XXX_MPP_AOUT_LVL_1V25 0
> +#define PM8XXX_MPP_AOUT_LVL_1V25_2 1
> +#define PM8XXX_MPP_AOUT_LVL_0V625 2
> +#define PM8XXX_MPP_AOUT_LVL_0V3125 3
> +#define PM8XXX_MPP_AOUT_LVL_MPP 4
> +#define PM8XXX_MPP_AOUT_LVL_ABUS1 5
> +#define PM8XXX_MPP_AOUT_LVL_ABUS2 6
> +#define PM8XXX_MPP_AOUT_LVL_ABUS3 7
> +
> +/* Analog Output: control */
> +#define PM8XXX_MPP_AOUT_CTRL_DISABLE 0
> +#define PM8XXX_MPP_AOUT_CTRL_ENABLE 1
> +#define PM8XXX_MPP_AOUT_CTRL_MPP_HIGH_EN 2
> +#define PM8XXX_MPP_AOUT_CTRL_MPP_LOW_EN 3
> +
> +/* Current Sink: level */
> +#define PM8XXX_MPP_CS_OUT_5MA 0
> +#define PM8XXX_MPP_CS_OUT_10MA 1
> +#define PM8XXX_MPP_CS_OUT_15MA 2
> +#define PM8XXX_MPP_CS_OUT_20MA 3
> +#define PM8XXX_MPP_CS_OUT_25MA 4
> +#define PM8XXX_MPP_CS_OUT_30MA 5
> +#define PM8XXX_MPP_CS_OUT_35MA 6
> +#define PM8XXX_MPP_CS_OUT_40MA 7
> +
> +/* Current Sink: control */
> +#define PM8XXX_MPP_CS_CTRL_DISABLE 0
> +#define PM8XXX_MPP_CS_CTRL_ENABLE 1
> +#define PM8XXX_MPP_CS_CTRL_MPP_HIGH_EN 2
> +#define PM8XXX_MPP_CS_CTRL_MPP_LOW_EN 3
> +
> +/* DTEST Current Sink: control */
> +#define PM8XXX_MPP_DTEST_CS_CTRL_EN1 0
> +#define PM8XXX_MPP_DTEST_CS_CTRL_EN2 1
> +#define PM8XXX_MPP_DTEST_CS_CTRL_EN3 2
> +#define PM8XXX_MPP_DTEST_CS_CTRL_EN4 3
> +
> +/* DTEST Digital Output: control */
> +#define PM8XXX_MPP_DTEST_DBUS1 0
> +#define PM8XXX_MPP_DTEST_DBUS2 1
> +#define PM8XXX_MPP_DTEST_DBUS3 2
> +#define PM8XXX_MPP_DTEST_DBUS4 3
> +
> +#endif
> diff --git a/include/linux/mfd/pm8xxx/pm8921.h b/include/linux/mfd/pm8xxx/pm8921.h
> index def8c31..19cffb2 100644
> --- a/include/linux/mfd/pm8xxx/pm8921.h
> +++ b/include/linux/mfd/pm8xxx/pm8921.h
> @@ -21,22 +21,29 @@
> #include <linux/device.h>
> #include <linux/mfd/pm8xxx/irq.h>
> #include <linux/mfd/pm8xxx/gpio.h>
> +#include <linux/mfd/pm8xxx/mpp.h>
>
> #define PM8921_NR_IRQS 256
>
> #define PM8921_NR_GPIOS 44
>
> +#define PM8921_NR_MPPS 12
> +
> #define PM8921_GPIO_BLOCK_START 24
> +#define PM8921_MPP_BLOCK_START 16
> #define PM8921_IRQ_BLOCK_BIT(block, bit) ((block) * 8 + (bit))
>
> -/* GPIOs [1,N] */
> +/* GPIOs and MPPs [1,N] */
> #define PM8921_GPIO_IRQ(base, gpio) ((base) + \
> PM8921_IRQ_BLOCK_BIT(PM8921_GPIO_BLOCK_START, (gpio)-1))
> +#define PM8921_MPP_IRQ(base, mpp) ((base) + \
> + PM8921_IRQ_BLOCK_BIT(PM8921_MPP_BLOCK_START, (mpp)-1))
>
> struct pm8921_platform_data {
> int irq_base;
> struct pm8xxx_irq_platform_data *irq_pdata;
> struct pm8xxx_gpio_platform_data *gpio_pdata;
> + struct pm8xxx_mpp_platform_data *mpp_pdata;
> };
>
> #endif
--
--
Sent by an employee of the Qualcomm Innovation Center, Inc. The Qualcomm
Innovation Center, Inc. is a member of the Code Aurora Forum.
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PM8921 MFD V4 5/6] MAINTAINERS: Add patterns for pmic 8921 files to MSM subsystem
2011-03-18 4:21 [PM8921 MFD V4 0/6] pm8921 core and subdevices adharmap
` (3 preceding siblings ...)
2011-03-18 4:21 ` [PM8921 MFD V4 4/6] mfd: pm8xxx-mpp: Add pm8xxx MPP driver adharmap
@ 2011-03-18 4:21 ` adharmap
2011-03-18 4:21 ` [PM8921 MFD V4 6/6] msm: board-8960: Add support for pm8921 adharmap
5 siblings, 0 replies; 10+ messages in thread
From: adharmap @ 2011-03-18 4:21 UTC (permalink / raw)
To: davidb, dwalker
Cc: Abhijeet Dharmapurikar, Andrew Morton, Joe Perches,
David S. Miller, Greg Kroah-Hartman, linux-kernel,
linux-arm-msm-owner, linux-arm-msm, linux-arm-kernel, Mark Brown,
Linus Walleij, Thomas Glexiner
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
---
MAINTAINERS | 2 ++
1 files changed, 2 insertions(+), 0 deletions(-)
diff --git a/MAINTAINERS b/MAINTAINERS
index 696cb18..71566a1 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -905,6 +905,8 @@ F: drivers/mmc/host/msm_sdcc.h
F: drivers/tty/serial/msm_serial.h
F: drivers/tty/serial/msm_serial.c
F: drivers/platform/msm/
+F: drivers/*/pm8???-*
+F: include/linux/mfd/pm8xxx/
T: git git://codeaurora.org/quic/kernel/davidb/linux-msm.git
S: Maintained
--
1.7.1
Sent by an employee of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PM8921 MFD V4 6/6] msm: board-8960: Add support for pm8921
2011-03-18 4:21 [PM8921 MFD V4 0/6] pm8921 core and subdevices adharmap
` (4 preceding siblings ...)
2011-03-18 4:21 ` [PM8921 MFD V4 5/6] MAINTAINERS: Add patterns for pmic 8921 files to MSM subsystem adharmap
@ 2011-03-18 4:21 ` adharmap
5 siblings, 0 replies; 10+ messages in thread
From: adharmap @ 2011-03-18 4:21 UTC (permalink / raw)
To: davidb, dwalker
Cc: Abhijeet Dharmapurikar, David Collins, Bryan Huntsman,
Russell King, Stepan Moskovchenko, linux-arm-msm,
linux-arm-kernel, linux-kernel, linux-arm-msm-owner,
linux-arm-kernel, Mark Brown, Linus Walleij, Thomas Glexiner,
Greg Kroah-Hartman
Add device structure declarations to the msm8960 board file
for PMIC 8921 chip and its subdevices.
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: David Collins <collinsd@codeaurora.org>
---
arch/arm/mach-msm/board-msm8960.c | 47 ++++++++++++++++++++++------
arch/arm/mach-msm/include/mach/irqs-8960.h | 9 ++---
2 files changed, 41 insertions(+), 15 deletions(-)
diff --git a/arch/arm/mach-msm/board-msm8960.c b/arch/arm/mach-msm/board-msm8960.c
index bf1a24b..1c90789 100644
--- a/arch/arm/mach-msm/board-msm8960.c
+++ b/arch/arm/mach-msm/board-msm8960.c
@@ -8,19 +8,15 @@
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
- * 02110-1301, USA.
- *
*/
+
#include <linux/kernel.h>
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/irq.h>
#include <linux/clkdev.h>
#include <linux/msm_ssbi.h>
+#include <linux/mfd/pm8xxx/pm8921.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
@@ -28,9 +24,18 @@
#include <mach/board.h>
#include <mach/msm_iomap.h>
+#include <mach/irqs.h>
#include "devices.h"
+/* Macros assume PMIC GPIOs and MPPs start at 1 */
+#define PM8921_GPIO_BASE NR_GPIO_IRQS
+#define PM8921_GPIO_PM_TO_SYS(pm_gpio) (pm_gpio - 1 + PM8921_GPIO_BASE)
+#define PM8921_MPP_BASE (PM8921_GPIO_BASE + PM8921_NR_GPIOS)
+#define PM8921_MPP_PM_TO_SYS(pm_gpio) (pm_gpio - 1 + PM8921_MPP_BASE)
+#define PM8921_IRQ_BASE (NR_MSM_IRQS + NR_GPIO_IRQS)
+#define PM8921_MPP_IRQ_BASE (PM8921_IRQ_BASE + NR_GPIO_IRQS)
+
static void __init msm8960_map_io(void)
{
msm_map_msm8960_io();
@@ -65,12 +70,34 @@ static struct platform_device *sim_devices[] __initdata = {
static struct platform_device *rumi3_devices[] __initdata = {
&msm8960_device_uart_gsbi5,
+ &msm8960_device_ssbi_pm8921,
+};
+
+static struct pm8xxx_irq_platform_data pm8xxx_irq_pdata __devinitdata = {
+ .irq_base = PM8921_IRQ_BASE,
+ .devirq = MSM_GPIO_TO_INT(104),
+ .irq_trigger_flag = IRQF_TRIGGER_LOW,
+};
+
+static struct pm8xxx_gpio_platform_data pm8xxx_gpio_pdata __devinitdata = {
+ .gpio_base = PM8921_GPIO_PM_TO_SYS(1),
+};
+
+static struct pm8xxx_mpp_platform_data pm8xxx_mpp_pdata __devinitdata = {
+ .mpp_base = PM8921_MPP_PM_TO_SYS(1),
+};
+
+static struct pm8921_platform_data pm8921_platform_data __devinitdata = {
+ .irq_pdata = &pm8xxx_irq_pdata,
+ .gpio_pdata = &pm8xxx_gpio_pdata,
+ .mpp_pdata = &pm8xxx_mpp_pdata,
};
-static struct msm_ssbi_platform_data msm8960_ssbi_pm8921_pdata = {
- .controller_type = MSM_SBI_CTRL_PMIC_ARBITER,
- .slave = {
- .name = "pm8921-core",
+static struct msm_ssbi_platform_data msm8960_ssbi_pm8921_pdata __initdata = {
+ .controller_type = MSM_SBI_CTRL_PMIC_ARBITER,
+ .slave = {
+ .name = "pm8921-core",
+ .platform_data = &pm8921_platform_data,
},
};
diff --git a/arch/arm/mach-msm/include/mach/irqs-8960.h b/arch/arm/mach-msm/include/mach/irqs-8960.h
index 81ab2a6..0a5b9c5 100644
--- a/arch/arm/mach-msm/include/mach/irqs-8960.h
+++ b/arch/arm/mach-msm/include/mach/irqs-8960.h
@@ -267,11 +267,10 @@
#define PM8921_SEC_IRQ_104 (GIC_SPI_START + 225)
#define PM8018_SEC_IRQ_107 (GIC_SPI_START + 226)
-/* For now, use the maximum number of interrupts until a pending GIC issue
- * is sorted out */
-#define NR_MSM_IRQS 1020
-#define NR_BOARD_IRQS 0
-#define NR_GPIO_IRQS 0
+#define NR_MSM_IRQS 256
+#define NR_GPIO_IRQS 150
+#define NR_PM8921_IRQS 256
+#define NR_BOARD_IRQS (NR_PM8921_IRQS)
#endif
--
1.7.1
Sent by an employee of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
^ permalink raw reply related [flat|nested] 10+ messages in thread