Re: [PATCH v2 2/2] usb: typec: Add support for Parade PS8830 Type-C Retimer

[Christophe JAILLET <christophe.jaillet@wanadoo.fr>]

Le 04/10/2024 à 15:57, Abel Vesa a écrit :
> The Parade PS8830 is a Type-C muti-protocol retimer controlled over I2C.
> It provides both altmode and orientation handling.
> 
> Add a driver with support for the following modes:
>   - DP 4lanes
>   - DP 2lanes + USB3
>   - USB3
> 
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---

Hi,

> +static int ps8830_retimer_probe(struct i2c_client *client)
> +{
> +	struct device *dev = &client->dev;
> +	struct typec_switch_desc sw_desc = { };
> +	struct typec_retimer_desc rtmr_desc = { };
> +	struct ps8830_retimer *retimer;
> +	int ret;
> +
> +	retimer = devm_kzalloc(dev, sizeof(*retimer), GFP_KERNEL);
> +	if (!retimer)
> +		return -ENOMEM;
> +
> +	retimer->client = client;
> +
> +	mutex_init(&retimer->lock);
> +
> +	retimer->regmap = devm_regmap_init_i2c(client, &ps8830_retimer_regmap);
> +	if (IS_ERR(retimer->regmap)) {
> +		dev_err(dev, "failed to allocate register map\n");
> +		return PTR_ERR(retimer->regmap);
> +	}
> +
> +	ret = ps8830_get_vregs(retimer);
> +	if (ret)
> +		return ret;
> +
> +	retimer->xo_clk = devm_clk_get(dev, "xo");
> +	if (IS_ERR(retimer->xo_clk))
> +		return dev_err_probe(dev, PTR_ERR(retimer->xo_clk),
> +				     "failed to get xo clock\n");
> +
> +	retimer->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
> +	if (IS_ERR(retimer->reset_gpio))
> +		return dev_err_probe(dev, PTR_ERR(retimer->reset_gpio),
> +				     "failed to get reset gpio\n");
> +
> +	retimer->typec_switch = fwnode_typec_switch_get(dev->fwnode);
> +	if (IS_ERR(retimer->typec_switch)) {
> +		dev_err(dev, "failed to acquire orientation-switch\n");
> +		return PTR_ERR(retimer->typec_switch);
> +	}
> +
> +	retimer->typec_mux = fwnode_typec_mux_get(dev->fwnode);
> +	if (IS_ERR(retimer->typec_mux)) {
> +		dev_err(dev, "failed to acquire mode-mux\n");
> +		goto err_switch_put;
> +	}
> +
> +	sw_desc.drvdata = retimer;
> +	sw_desc.fwnode = dev_fwnode(dev);
> +	sw_desc.set = ps8830_sw_set;
> +
> +	ret = drm_aux_bridge_register(dev);
> +	if (ret)
> +		goto err_mux_put;
> +
> +	retimer->sw = typec_switch_register(dev, &sw_desc);
> +	if (IS_ERR(retimer->sw)) {
> +		dev_err(dev, "failed to register typec switch\n");
> +		goto err_aux_bridge_unregister;
> +	}
> +
> +	rtmr_desc.drvdata = retimer;
> +	rtmr_desc.fwnode = dev_fwnode(dev);
> +	rtmr_desc.set = ps8830_retimer_set;
> +
> +	retimer->retimer = typec_retimer_register(dev, &rtmr_desc);
> +	if (IS_ERR(retimer->retimer)) {
> +		dev_err(dev, "failed to register typec retimer\n");
> +		goto err_switch_unregister;
> +	}
> +
> +	ret = clk_prepare_enable(retimer->xo_clk);
> +	if (ret) {
> +		dev_err(dev, "failed to enable XO: %d\n", ret);
> +		goto err_retimer_unregister;
> +	}
> +
> +	ret = ps8830_enable_vregs(retimer);
> +	if (ret)
> +		goto err_clk_disable;
> +
> +	/* delay needed as per datasheet */
> +	usleep_range(4000, 14000);
> +
> +	gpiod_set_value(retimer->reset_gpio, 1);
> +
> +	return 0;
> +
> +err_clk_disable:
> +	clk_disable_unprepare(retimer->xo_clk);
> +
> +err_retimer_unregister:
> +	typec_retimer_unregister(retimer->retimer);
> +
> +err_switch_unregister:
> +	typec_switch_unregister(retimer->sw);
> +
> +err_aux_bridge_unregister:
> +	gpiod_set_value(retimer->reset_gpio, 0);

Is this called useful here?
gpiod_set_value(, 1) has not been called yet.

It made sense to have something like that in v1, but it looks strange in v2.

CJ

> +	clk_disable_unprepare(retimer->xo_clk);
> +
> +err_mux_put:
> +	typec_mux_put(retimer->typec_mux);
> +
> +err_switch_put:
> +	typec_switch_put(retimer->typec_switch);
> +
> +	return ret;
> +}

...