[PATCH net-next v7 00/15] net: phy: Introduce PHY ports representation

[PATCH net-next v7 00/15] net: phy: Introduce PHY ports representation

[Maxime Chevallier]

Hi everyone,

Here's a V7 for the ongoing support for Ethernet media-side port
support.

This V7 addresses some of the shortcomings, including :
 - A rework of the way we assign each port's supported field
 - The support for combo-ports on the marvell 88x3310
 - Patch 2 is back, it was removed after Russell's comments in RFCV2.

At that time, Russell said :

" > Mark BaseT as being a 4-lanes mode.

This is a problem:

1.4.50 10BASE-T: IEEE 802.3 Physical Layer specification for a 10 Mb/s
CSMA/CD local area network over two pairs of twisted-pair telephone
wire. (See IEEE Std 802.3, Clause 14.)

Then we have the 100BASE-T* family, which can be T1, T2, T4 or TX.
T1 is over a single balanced twisted pair. T2 is over two pairs of
Cat 3 or better. T4 is over four pairs of Cat3/4/5.

The common 100BASE-T* type is TX, which is over two pairs of Cat5.
This is sadly what the ethtool 100baseT link modes are used to refer
to.

We do have a separate link mode for 100baseT1, but not 100baseT4.

So, these ethtool modes that are of the form baseT so far are
describing generally two pairs, one pair in each direction. (T1 is
a single pair that is bidirectional.)

It's only once we get to 1000BASE-T (1000baseT) that we get to an
ethtool link mode that has four lanes in a bidirectional fashion.

So, simply redefining this ends up changing 10baseT and 100baseT from
a single lane in each direction to four lanes (and is a "lane" here
defined as the total number of pairs used for communication in both
directions, or the total number of lanes used in either direction.

Hence, I'm not sure this makes sense."

Russell it completely right, and I failed to make my point at that time.
Now, I think this patch does make sense as :
 - We treat BaseT1 as its own medium
 - In patch 3, we enforce the following :
   - 10 and 100BaseT work on 2 pairs, but can also work on a 4-pair port
   - 1000BaseT and above need 4 pairs

I'm again open for any kind of discussion :)

Before going into the details, a few important notes :

 - This is only a first phase. It instantiates the port, and leverage
   that to make the MAC <-> PHY <-> SFP usecase simpler.

 - Next phase will deal with controlling the port state, as well as the
   netlink uAPI for that.

 - The end-goal is to enable support for complex port MUX. This
   preliminary work focuses on PHY-driven ports, but this will be
   extended to support muxing at the MII level (Multi-phy, or compo PHY
   + SFP as found on Turris Omnia for example).

 - The naming is definitely not set in stone. I named that "phy_port",
   but this may convey the false sense that this is phylib-specific.
   Even the word "port" is not that great, as it already has several
   different meanings in the net world (switch port, devlink port,
   etc.). I used the term "connector" in the binding.

A bit of history on that work :

The end goal that I personnaly want to achieve is :

            + PHY - RJ45
            | 
 MAC - MUX -+ PHY - RJ45

After many discussions here on netdev@, but also at netdevconf[1] and
LPC[2], there appears to be several analoguous designs that exist out
there.

[1] : https://netdevconf.info/0x17/sessions/talk/improving-multi-phy-and-multi-port-interfaces.html
[2] : https://lpc.events/event/18/contributions/1964/ (video isn't the
right one)

Take the MAchiatobin, it has 2 interfaces that looks like this :

 MAC - PHY -+ RJ45
            |
	    + SFP - Whatever the module does

Now, looking at the Turris Omnia, we have :


 MAC - MUX -+ PHY - RJ45
            |
	    + SFP - Whatever the module does

We can find more example of this kind of designs, the common part is
that we expose multiple front-facing media ports. This is what this
current work aims at supporting. As of right now, it does'nt add any
support for muxing, but this will come later on.

This first phase focuses on phy-driven ports only, but there are already
quite some challenges already. For one, we can't really autodetect how
many ports are sitting behind a PHY. That's why this series introduces a
new binding. Describing ports in DT should however be a last-resort
thing when we need to clear some ambiguity about the PHY media-side.

The only use-cases that we have today for multi-port PHYs are combo PHYs
that drive both a Copper port and an SFP (the Macchiatobin case). This
in itself is challenging and this series only addresses part of this
support, by registering a phy_port for the PHY <-> SFP connection. The
SFP module should in the end be considered as a port as well, but that's
not yet the case.

However, because now PHYs can register phy_ports for every media-side
interface they have, they can register the capabilities of their ports,
which allows making the PHY-driver SFP case much more generic.

Let me know what you think, I'm all in for discussions :)

Regards,

Changes in V7:
 - Move ethtool_medium_get_supported to phy_caps
 - support combo-ports, each with a given set of supported modes
 - Introduce the notion of 'not-described' ports

Changes in V6:

 - Fixed kdoc on patch 3
 - Addressed a missing port-ops registration for the Marvell 88x2222
   driver
 - Addressed a warning reported by Simon on the DP83822 when building
   without CONFIG_OF_MDIO

Changes in V5 :

 - renamed the bindings to use the term "connector" instead of "port"
 - Rebased, and fixed some issues reported on the 83822 driver
 - Use phy_caps

Changes in V4 :

 - Introduced a kernel doc
 - Reworked the mediums definitions in patch 2
 - QCA807x now uses the generic SFP support
 - Fixed some implementation bugs to build the support list based on the
   interfaces supported on a port

V6: https://lore.kernel.org/netdev/20250507135331.76021-1-maxime.chevallier@bootlin.com/
V5: https://lore.kernel.org/netdev/20250425141511.182537-1-maxime.chevallier@bootlin.com/
V4: https://lore.kernel.org/netdev/20250213101606.1154014-1-maxime.chevallier@bootlin.com/
V3: https://lore.kernel.org/netdev/20250207223634.600218-1-maxime.chevallier@bootlin.com/
RFC V2: https://lore.kernel.org/netdev/20250122174252.82730-1-maxime.chevallier@bootlin.com/
RFC V1: https://lore.kernel.org/netdev/20241220201506.2791940-1-maxime.chevallier@bootlin.com/

Maxime

Maxime Chevallier (15):
  dt-bindings: net: Introduce the ethernet-connector description
  net: ethtool: common: Indicate that BaseT works on up to 4 lanes
  net: ethtool: Introduce ETHTOOL_LINK_MEDIUM_* values
  net: phy: Introduce PHY ports representation
  net: phy: dp83822: Add support for phy_port representation
  net: phy: Create a phy_port for PHY-driven SFPs
  net: phy: Introduce generic SFP handling for PHY drivers
  net: phy: marvell-88x2222: Support SFP through phy_port interface
  net: phy: marvell: Support SFP through phy_port interface
  net: phy: marvell10g: Support SFP through phy_port
  net: phy: at803x: Support SFP through phy_port interface
  net: phy: qca807x: Support SFP through phy_port interface
  net: phy: Only rely on phy_port for PHY-driven SFP
  net: phy: dp83822: Add SFP support through the phy_port interface
  Documentation: networking: Document the phy_port infrastructure

 .../bindings/net/ethernet-connector.yaml      |  47 +++
 .../devicetree/bindings/net/ethernet-phy.yaml |  18 +
 Documentation/networking/index.rst            |   1 +
 Documentation/networking/phy-port.rst         | 111 ++++++
 MAINTAINERS                                   |   3 +
 drivers/net/phy/Makefile                      |   2 +-
 drivers/net/phy/dp83822.c                     |  78 +++--
 drivers/net/phy/marvell-88x2222.c             |  98 +++---
 drivers/net/phy/marvell.c                     | 100 +++---
 drivers/net/phy/marvell10g.c                  |  47 +--
 drivers/net/phy/phy-caps.h                    |   5 +
 drivers/net/phy/phy_caps.c                    |  58 ++++
 drivers/net/phy/phy_device.c                  | 327 +++++++++++++++++-
 drivers/net/phy/phy_port.c                    | 173 +++++++++
 drivers/net/phy/qcom/at803x.c                 |  64 +---
 drivers/net/phy/qcom/qca807x.c                |  75 ++--
 include/linux/ethtool.h                       |  44 ++-
 include/linux/phy.h                           |  38 +-
 include/linux/phy_port.h                      |  97 ++++++
 include/uapi/linux/ethtool.h                  |  20 ++
 net/ethtool/common.c                          | 267 ++++++++------
 21 files changed, 1284 insertions(+), 389 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/net/ethernet-connector.yaml
 create mode 100644 Documentation/networking/phy-port.rst
 create mode 100644 drivers/net/phy/phy_port.c
 create mode 100644 include/linux/phy_port.h

-- 
2.49.0

[PATCH net-next v7 01/15] dt-bindings: net: Introduce the ethernet-connector description

[Maxime Chevallier]

The ability to describe the physical ports of Ethernet devices is useful
to describe multi-port devices, as well as to remove any ambiguity with
regard to the nature of the port.

Moreover, describing ports allows for a better description of features
that are tied to connectors, such as PoE through the PSE-PD devices.

Introduce a binding to allow describing the ports, for now with 2
attributes :

 - The number of lanes, which is a quite generic property that allows
   differentating between multiple similar technologies such as BaseT1
   and "regular" BaseT (which usually means BaseT4).

 - The media that can be used on that port, such as BaseT for Twisted
   Copper, BaseC for coax copper, BaseS/L for Fiber, BaseK for backplane
   ethernet, etc. This allows defining the nature of the port, and
   therefore avoids the need for vendor-specific properties such as
   "micrel,fiber-mode" or "ti,fiber-mode".

The port description lives in its own file, as it is intended in the
future to allow describing the ports for phy-less devices.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
 .../bindings/net/ethernet-connector.yaml      | 47 +++++++++++++++++++
 .../devicetree/bindings/net/ethernet-phy.yaml | 18 +++++++
 MAINTAINERS                                   |  1 +
 3 files changed, 66 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/ethernet-connector.yaml

diff --git a/Documentation/devicetree/bindings/net/ethernet-connector.yaml b/Documentation/devicetree/bindings/net/ethernet-connector.yaml
new file mode 100644
index 000000000000..2aa28e6c1523
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/ethernet-connector.yaml
@@ -0,0 +1,47 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/ethernet-connector.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Generic Ethernet Connector
+
+maintainers:
+  - Maxime Chevallier <maxime.chevallier@bootlin.com>
+
+description:
+  An Ethernet Connectr represents the output of a network component such as
+  a PHY, an Ethernet controller with no PHY, or an SFP module.
+
+properties:
+
+  lanes:
+    description:
+      Defines the number of lanes on the port, that is the number of physical
+      channels used to convey the data with the link partner.
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+  media:
+    description:
+      The mediums, as defined in 802.3, that can be used on the port.
+    items:
+      enum:
+        - BaseT
+        - BaseK
+        - BaseS
+        - BaseC
+        - BaseL
+        - BaseD
+        - BaseE
+        - BaseF
+        - BaseV
+        - BaseMLD
+        - BaseX
+
+required:
+  - lanes
+  - media
+
+additionalProperties: true
+
+...
diff --git a/Documentation/devicetree/bindings/net/ethernet-phy.yaml b/Documentation/devicetree/bindings/net/ethernet-phy.yaml
index 71e2cd32580f..6bf670beb66f 100644
--- a/Documentation/devicetree/bindings/net/ethernet-phy.yaml
+++ b/Documentation/devicetree/bindings/net/ethernet-phy.yaml
@@ -277,6 +277,17 @@ properties:
 
     additionalProperties: false
 
+  mdi:
+    type: object
+
+    patternProperties:
+      '^connector-[a-f0-9]+$':
+        $ref: /schemas/net/ethernet-connector.yaml#
+
+        unevaluatedProperties: false
+
+    additionalProperties: false
+
 required:
   - reg
 
@@ -313,5 +324,12 @@ examples:
                     default-state = "keep";
                 };
             };
+
+            mdi {
+              connector-0 {
+                lanes = <2>;
+                media = "BaseT";
+              };
+            };
         };
     };
diff --git a/MAINTAINERS b/MAINTAINERS
index bb9df569a3ff..20806cfc1003 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -8946,6 +8946,7 @@ R:	Russell King <linux@armlinux.org.uk>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	Documentation/ABI/testing/sysfs-class-net-phydev
+F:	Documentation/devicetree/bindings/net/ethernet-connector.yaml
 F:	Documentation/devicetree/bindings/net/ethernet-phy.yaml
 F:	Documentation/devicetree/bindings/net/mdio*
 F:	Documentation/devicetree/bindings/net/qca,ar803x.yaml
-- 
2.49.0

[PATCH net-next v7 02/15] net: ethtool: common: Indicate that BaseT works on up to 4 lanes

[Maxime Chevallier]

The way BaseT modes (Ethernet over twisted copper pairs) are represented
in the kernel are through the following modes :

  ETHTOOL_LINK_MODE_10baseT_Half
  ETHTOOL_LINK_MODE_10baseT_Full
  ETHTOOL_LINK_MODE_100baseT_Half
  ETHTOOL_LINK_MODE_100baseT_Full
  ETHTOOL_LINK_MODE_1000baseT_Half
  ETHTOOL_LINK_MODE_1000baseT_Full
  ETHTOOL_LINK_MODE_2500baseT_Full
  ETHTOOL_LINK_MODE_5000baseT_Full
  ETHTOOL_LINK_MODE_10000baseT_Full
  ETHTOOL_LINK_MODE_100baseT1_Full
  ETHTOOL_LINK_MODE_1000baseT1_Full
  ETHTOOL_LINK_MODE_10baseT1L_Full
  ETHTOOL_LINK_MODE_10baseT1S_Full
  ETHTOOL_LINK_MODE_10baseT1S_Half
  ETHTOOL_LINK_MODE_10baseT1S_P2MP_Half
  ETHTOOL_LINK_MODE_10baseT1BRR_Full

The baseT1* modes explicitly specify that they work on a single,
unshielded twister copper pair.

However, the other modes do not state the number of pairs that are used
to carry the link. 10 and 100BaseT use 2 twisted copper pairs, while
1GBaseT and higher use 4 pairs.

although 10 and 100BaseT use 2 pairs, they can work on a Cat3/4/5+
cables that contain 4 pairs.

Change the number of pairs associated to BaseT modes to indicate the
allowable number of pairs for BaseT. Further commits will then refine
the minimum number of pairs required for the linkmode to work.

BaseT1 modes aren't affected by this commit.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
 net/ethtool/common.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/net/ethtool/common.c b/net/ethtool/common.c
index eb253e0fd61b..bc1b625c9ff4 100644
--- a/net/ethtool/common.c
+++ b/net/ethtool/common.c
@@ -267,7 +267,7 @@ static_assert(ARRAY_SIZE(link_mode_names) == __ETHTOOL_LINK_MODE_MASK_NBITS);
 #define __LINK_MODE_LANES_LR8_ER8_FR8	8
 #define __LINK_MODE_LANES_LRM		1
 #define __LINK_MODE_LANES_MLD2		2
-#define __LINK_MODE_LANES_T		1
+#define __LINK_MODE_LANES_T		4
 #define __LINK_MODE_LANES_T1		1
 #define __LINK_MODE_LANES_X		1
 #define __LINK_MODE_LANES_FX		1
-- 
2.49.0

[PATCH net-next v7 03/15] net: ethtool: Introduce ETHTOOL_LINK_MEDIUM_* values

[Maxime Chevallier]

In an effort to have a better representation of Ethernet ports,
introduce enumeration values representing the various ethernet Mediums.

This is part of the 802.3 naming convention, for example :

1000 Base T 4
 |    |   | |
 |    |   | \_ lanes (4)
 |    |   \___ Medium (T == Twisted Copper Pairs)
 |    \_______ Baseband transmission
 \____________ Speed

 Other example :

10000 Base K X 4
           | | \_ lanes (4)
           | \___ encoding (BaseX is 8b/10b while BaseR is 66b/64b)
           \_____ Medium (K is backplane ethernet)

In the case of representing a physical port, only the medium and number
of lanes should be relevant. One exception would be 1000BaseX, which is
currently also used as a medium in what appears to be any of
1000BaseSX, 1000BaseCX and 1000BaseLX. This was reflected in the mediums
associated with the 1000BaseX linkmode.

These mediums are set in the net/ethtool/common.c lookup table that
maintains a list of all linkmodes with their number of lanes, medium,
encoding, speed and duplex.

One notable exception to this is 100M BaseT Ethernet. 100BaseTX is a
2-lanes protocol but it will also work on 4-lanes cables, so the lookup
table contains 2 sets of lane numbers, indicating the min number of lanes
for a protocol to work and the "nominal" number of lanes as well.

Another set of exceptions are linkmodes such 100000baseLR4_ER4, where
the same link mode seems to represent 100GBaseLR4 and 100GBaseER4. The
macro __DEFINE_LINK_MODE_PARAMS_MEDIUMS is here used to populate the
.mediums bitfield with all appropriate mediums.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
 include/linux/ethtool.h      |  18 ++-
 include/uapi/linux/ethtool.h |  20 +++
 net/ethtool/common.c         | 265 +++++++++++++++++++++--------------
 3 files changed, 191 insertions(+), 112 deletions(-)

diff --git a/include/linux/ethtool.h b/include/linux/ethtool.h
index 59877fd2a1d3..4db968201f68 100644
--- a/include/linux/ethtool.h
+++ b/include/linux/ethtool.h
@@ -216,13 +216,25 @@ static inline u8 *ethtool_rxfh_context_key(struct ethtool_rxfh_context *ctx)
 void ethtool_rxfh_context_lost(struct net_device *dev, u32 context_id);
 
 struct link_mode_info {
-	int                             speed;
-	u8                              lanes;
-	u8                              duplex;
+	int	speed;
+	u8	min_lanes;
+	u8	lanes;
+	u8	duplex;
+	u16	mediums;
 };
 
 extern const struct link_mode_info link_mode_params[];
 
+extern const char ethtool_link_medium_names[][ETH_GSTRING_LEN];
+
+static inline const char *phy_mediums(enum ethtool_link_medium medium)
+{
+	if (medium >= __ETHTOOL_LINK_MEDIUM_LAST)
+		return "unknown";
+
+	return ethtool_link_medium_names[medium];
+}
+
 /* declare a link mode bitmap */
 #define __ETHTOOL_DECLARE_LINK_MODE_MASK(name)		\
 	DECLARE_BITMAP(name, __ETHTOOL_LINK_MODE_MASK_NBITS)
diff --git a/include/uapi/linux/ethtool.h b/include/uapi/linux/ethtool.h
index 707c1844010c..a82d3adf6e98 100644
--- a/include/uapi/linux/ethtool.h
+++ b/include/uapi/linux/ethtool.h
@@ -2586,4 +2586,24 @@ enum phy_upstream {
 	PHY_UPSTREAM_PHY,
 };
 
+enum ethtool_link_medium {
+	ETHTOOL_LINK_MEDIUM_BASET = 0,
+	ETHTOOL_LINK_MEDIUM_BASEK,
+	ETHTOOL_LINK_MEDIUM_BASES,
+	ETHTOOL_LINK_MEDIUM_BASEC,
+	ETHTOOL_LINK_MEDIUM_BASEL,
+	ETHTOOL_LINK_MEDIUM_BASED,
+	ETHTOOL_LINK_MEDIUM_BASEE,
+	ETHTOOL_LINK_MEDIUM_BASEF,
+	ETHTOOL_LINK_MEDIUM_BASEV,
+	ETHTOOL_LINK_MEDIUM_BASEMLD,
+	ETHTOOL_LINK_MEDIUM_NONE,
+
+	__ETHTOOL_LINK_MEDIUM_LAST,
+};
+
+#define ETHTOOL_MEDIUM_FIBER_BITS (BIT(ETHTOOL_LINK_MEDIUM_BASES) | \
+				   BIT(ETHTOOL_LINK_MEDIUM_BASEL) | \
+				   BIT(ETHTOOL_LINK_MEDIUM_BASEF))
+
 #endif /* _UAPI_LINUX_ETHTOOL_H */
diff --git a/net/ethtool/common.c b/net/ethtool/common.c
index bc1b625c9ff4..c73bdb9ee42b 100644
--- a/net/ethtool/common.c
+++ b/net/ethtool/common.c
@@ -281,12 +281,32 @@ static_assert(ARRAY_SIZE(link_mode_names) == __ETHTOOL_LINK_MODE_MASK_NBITS);
 #define __LINK_MODE_LANES_DR8_2		8
 #define __LINK_MODE_LANES_T1BRR		1
 
-#define __DEFINE_LINK_MODE_PARAMS(_speed, _type, _duplex)	\
+#define __DEFINE_LINK_MODE_PARAMS_LANES(_speed, _type, _min_lanes, _lanes, _duplex, _medium) \
 	[ETHTOOL_LINK_MODE(_speed, _type, _duplex)] = {		\
 		.speed  = SPEED_ ## _speed, \
+		.min_lanes  = _min_lanes, \
+		.lanes  = _lanes, \
+		.duplex	= __DUPLEX_ ## _duplex, \
+		.mediums = BIT(ETHTOOL_LINK_MEDIUM_BASE ## _medium) \
+	}
+
+#define __DEFINE_LINK_MODE_PARAMS(_speed, _type, _duplex, _medium)	\
+	[ETHTOOL_LINK_MODE(_speed, _type, _duplex)] = {		\
+		.speed  = SPEED_ ## _speed, \
+		.min_lanes  = __LINK_MODE_LANES_ ## _type, \
+		.lanes  = __LINK_MODE_LANES_ ## _type, \
+		.duplex	= __DUPLEX_ ## _duplex, \
+		.mediums = BIT(ETHTOOL_LINK_MEDIUM_BASE ## _medium) \
+	}
+#define __DEFINE_LINK_MODE_PARAMS_MEDIUMS(_speed, _type, _duplex, _mediums)	\
+	[ETHTOOL_LINK_MODE(_speed, _type, _duplex)] = {		\
+		.speed  = SPEED_ ## _speed, \
+		.min_lanes  = __LINK_MODE_LANES_ ## _type, \
 		.lanes  = __LINK_MODE_LANES_ ## _type, \
-		.duplex	= __DUPLEX_ ## _duplex \
+		.duplex	= __DUPLEX_ ## _duplex, \
+		.mediums = (_mediums) \
 	}
+#define __MED(_medium)	(BIT(ETHTOOL_LINK_MEDIUM_BASE ## _medium))
 #define __DUPLEX_Half DUPLEX_HALF
 #define __DUPLEX_Full DUPLEX_FULL
 #define __DEFINE_SPECIAL_MODE_PARAMS(_mode) \
@@ -294,138 +314,165 @@ static_assert(ARRAY_SIZE(link_mode_names) == __ETHTOOL_LINK_MODE_MASK_NBITS);
 		.speed	= SPEED_UNKNOWN, \
 		.lanes	= 0, \
 		.duplex	= DUPLEX_UNKNOWN, \
+		.mediums = BIT(ETHTOOL_LINK_MEDIUM_NONE), \
 	}
 
 const struct link_mode_info link_mode_params[] = {
-	__DEFINE_LINK_MODE_PARAMS(10, T, Half),
-	__DEFINE_LINK_MODE_PARAMS(10, T, Full),
-	__DEFINE_LINK_MODE_PARAMS(100, T, Half),
-	__DEFINE_LINK_MODE_PARAMS(100, T, Full),
-	__DEFINE_LINK_MODE_PARAMS(1000, T, Half),
-	__DEFINE_LINK_MODE_PARAMS(1000, T, Full),
+	__DEFINE_LINK_MODE_PARAMS_LANES(10, T, 2, 4, Half, T),
+	__DEFINE_LINK_MODE_PARAMS_LANES(10, T, 2, 4, Full, T),
+	__DEFINE_LINK_MODE_PARAMS_LANES(100, T, 2, 4, Half, T),
+	__DEFINE_LINK_MODE_PARAMS_LANES(100, T, 2, 4, Full, T),
+	__DEFINE_LINK_MODE_PARAMS(1000, T, Half, T),
+	__DEFINE_LINK_MODE_PARAMS(1000, T, Full, T),
 	__DEFINE_SPECIAL_MODE_PARAMS(Autoneg),
 	__DEFINE_SPECIAL_MODE_PARAMS(TP),
 	__DEFINE_SPECIAL_MODE_PARAMS(AUI),
 	__DEFINE_SPECIAL_MODE_PARAMS(MII),
 	__DEFINE_SPECIAL_MODE_PARAMS(FIBRE),
 	__DEFINE_SPECIAL_MODE_PARAMS(BNC),
-	__DEFINE_LINK_MODE_PARAMS(10000, T, Full),
+	__DEFINE_LINK_MODE_PARAMS(10000, T, Full, T),
 	__DEFINE_SPECIAL_MODE_PARAMS(Pause),
 	__DEFINE_SPECIAL_MODE_PARAMS(Asym_Pause),
-	__DEFINE_LINK_MODE_PARAMS(2500, X, Full),
+	__DEFINE_LINK_MODE_PARAMS_MEDIUMS(2500, X, Full,
+					  __MED(C) | __MED(S) | __MED(L)),
 	__DEFINE_SPECIAL_MODE_PARAMS(Backplane),
-	__DEFINE_LINK_MODE_PARAMS(1000, KX, Full),
-	__DEFINE_LINK_MODE_PARAMS(10000, KX4, Full),
-	__DEFINE_LINK_MODE_PARAMS(10000, KR, Full),
+	__DEFINE_LINK_MODE_PARAMS(1000, KX, Full, K),
+	__DEFINE_LINK_MODE_PARAMS(10000, KX4, Full, K),
+	__DEFINE_LINK_MODE_PARAMS(10000, KR, Full, K),
 	[ETHTOOL_LINK_MODE_10000baseR_FEC_BIT] = {
 		.speed	= SPEED_10000,
 		.lanes	= 1,
 		.duplex = DUPLEX_FULL,
 	},
-	__DEFINE_LINK_MODE_PARAMS(20000, MLD2, Full),
-	__DEFINE_LINK_MODE_PARAMS(20000, KR2, Full),
-	__DEFINE_LINK_MODE_PARAMS(40000, KR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(40000, CR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(40000, SR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(40000, LR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(56000, KR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(56000, CR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(56000, SR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(56000, LR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(25000, CR, Full),
-	__DEFINE_LINK_MODE_PARAMS(25000, KR, Full),
-	__DEFINE_LINK_MODE_PARAMS(25000, SR, Full),
-	__DEFINE_LINK_MODE_PARAMS(50000, CR2, Full),
-	__DEFINE_LINK_MODE_PARAMS(50000, KR2, Full),
-	__DEFINE_LINK_MODE_PARAMS(100000, KR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(100000, SR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(100000, CR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(100000, LR4_ER4, Full),
-	__DEFINE_LINK_MODE_PARAMS(50000, SR2, Full),
-	__DEFINE_LINK_MODE_PARAMS(1000, X, Full),
-	__DEFINE_LINK_MODE_PARAMS(10000, CR, Full),
-	__DEFINE_LINK_MODE_PARAMS(10000, SR, Full),
-	__DEFINE_LINK_MODE_PARAMS(10000, LR, Full),
-	__DEFINE_LINK_MODE_PARAMS(10000, LRM, Full),
-	__DEFINE_LINK_MODE_PARAMS(10000, ER, Full),
-	__DEFINE_LINK_MODE_PARAMS(2500, T, Full),
-	__DEFINE_LINK_MODE_PARAMS(5000, T, Full),
+	__DEFINE_LINK_MODE_PARAMS(20000, MLD2, Full, MLD),
+	__DEFINE_LINK_MODE_PARAMS(20000, KR2, Full, K),
+	__DEFINE_LINK_MODE_PARAMS(40000, KR4, Full, K),
+	__DEFINE_LINK_MODE_PARAMS(40000, CR4, Full, C),
+	__DEFINE_LINK_MODE_PARAMS(40000, SR4, Full, S),
+	__DEFINE_LINK_MODE_PARAMS(40000, LR4, Full, L),
+	__DEFINE_LINK_MODE_PARAMS(56000, KR4, Full, K),
+	__DEFINE_LINK_MODE_PARAMS(56000, CR4, Full, C),
+	__DEFINE_LINK_MODE_PARAMS(56000, SR4, Full, S),
+	__DEFINE_LINK_MODE_PARAMS(56000, LR4, Full, L),
+	__DEFINE_LINK_MODE_PARAMS(25000, CR, Full, C),
+	__DEFINE_LINK_MODE_PARAMS(25000, KR, Full, K),
+	__DEFINE_LINK_MODE_PARAMS(25000, SR, Full, S),
+	__DEFINE_LINK_MODE_PARAMS(50000, CR2, Full, C),
+	__DEFINE_LINK_MODE_PARAMS(50000, KR2, Full, K),
+	__DEFINE_LINK_MODE_PARAMS(100000, KR4, Full, K),
+	__DEFINE_LINK_MODE_PARAMS(100000, SR4, Full, S),
+	__DEFINE_LINK_MODE_PARAMS(100000, CR4, Full, C),
+	__DEFINE_LINK_MODE_PARAMS_MEDIUMS(100000, LR4_ER4, Full,
+					  __MED(L) | __MED(E)),
+	__DEFINE_LINK_MODE_PARAMS(50000, SR2, Full, S),
+	__DEFINE_LINK_MODE_PARAMS_MEDIUMS(1000, X, Full,
+					  __MED(C) | __MED(S) | __MED(L)),
+	__DEFINE_LINK_MODE_PARAMS(10000, CR, Full, C),
+	__DEFINE_LINK_MODE_PARAMS(10000, SR, Full, S),
+	__DEFINE_LINK_MODE_PARAMS(10000, LR, Full, L),
+	__DEFINE_LINK_MODE_PARAMS(10000, LRM, Full, L),
+	__DEFINE_LINK_MODE_PARAMS(10000, ER, Full, E),
+	__DEFINE_LINK_MODE_PARAMS(2500, T, Full, T),
+	__DEFINE_LINK_MODE_PARAMS(5000, T, Full, T),
 	__DEFINE_SPECIAL_MODE_PARAMS(FEC_NONE),
 	__DEFINE_SPECIAL_MODE_PARAMS(FEC_RS),
 	__DEFINE_SPECIAL_MODE_PARAMS(FEC_BASER),
-	__DEFINE_LINK_MODE_PARAMS(50000, KR, Full),
-	__DEFINE_LINK_MODE_PARAMS(50000, SR, Full),
-	__DEFINE_LINK_MODE_PARAMS(50000, CR, Full),
-	__DEFINE_LINK_MODE_PARAMS(50000, LR_ER_FR, Full),
-	__DEFINE_LINK_MODE_PARAMS(50000, DR, Full),
-	__DEFINE_LINK_MODE_PARAMS(100000, KR2, Full),
-	__DEFINE_LINK_MODE_PARAMS(100000, SR2, Full),
-	__DEFINE_LINK_MODE_PARAMS(100000, CR2, Full),
-	__DEFINE_LINK_MODE_PARAMS(100000, LR2_ER2_FR2, Full),
-	__DEFINE_LINK_MODE_PARAMS(100000, DR2, Full),
-	__DEFINE_LINK_MODE_PARAMS(200000, KR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(200000, SR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(200000, LR4_ER4_FR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(200000, DR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(200000, CR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(100, T1, Full),
-	__DEFINE_LINK_MODE_PARAMS(1000, T1, Full),
-	__DEFINE_LINK_MODE_PARAMS(400000, KR8, Full),
-	__DEFINE_LINK_MODE_PARAMS(400000, SR8, Full),
-	__DEFINE_LINK_MODE_PARAMS(400000, LR8_ER8_FR8, Full),
-	__DEFINE_LINK_MODE_PARAMS(400000, DR8, Full),
-	__DEFINE_LINK_MODE_PARAMS(400000, CR8, Full),
+	__DEFINE_LINK_MODE_PARAMS(50000, KR, Full, K),
+	__DEFINE_LINK_MODE_PARAMS(50000, SR, Full, S),
+	__DEFINE_LINK_MODE_PARAMS(50000, CR, Full, C),
+	__DEFINE_LINK_MODE_PARAMS_MEDIUMS(50000, LR_ER_FR, Full,
+					  __MED(L) | __MED(E) | __MED(F)),
+	__DEFINE_LINK_MODE_PARAMS(50000, DR, Full, D),
+	__DEFINE_LINK_MODE_PARAMS(100000, KR2, Full, K),
+	__DEFINE_LINK_MODE_PARAMS(100000, SR2, Full, S),
+	__DEFINE_LINK_MODE_PARAMS(100000, CR2, Full, C),
+	__DEFINE_LINK_MODE_PARAMS_MEDIUMS(100000, LR2_ER2_FR2, Full,
+					  __MED(L) | __MED(E) | __MED(F)),
+	__DEFINE_LINK_MODE_PARAMS(100000, DR2, Full, D),
+	__DEFINE_LINK_MODE_PARAMS(200000, KR4, Full, K),
+	__DEFINE_LINK_MODE_PARAMS(200000, SR4, Full, S),
+	__DEFINE_LINK_MODE_PARAMS_MEDIUMS(200000, LR4_ER4_FR4, Full,
+					  __MED(L) | __MED(E) | __MED(F)),
+	__DEFINE_LINK_MODE_PARAMS(200000, DR4, Full, D),
+	__DEFINE_LINK_MODE_PARAMS(200000, CR4, Full, C),
+	__DEFINE_LINK_MODE_PARAMS(100, T1, Full, T),
+	__DEFINE_LINK_MODE_PARAMS(1000, T1, Full, T),
+	__DEFINE_LINK_MODE_PARAMS(400000, KR8, Full, K),
+	__DEFINE_LINK_MODE_PARAMS(400000, SR8, Full, S),
+	__DEFINE_LINK_MODE_PARAMS_MEDIUMS(400000, LR8_ER8_FR8, Full,
+					  __MED(L) | __MED(E) | __MED(F)),
+	__DEFINE_LINK_MODE_PARAMS(400000, DR8, Full, D),
+	__DEFINE_LINK_MODE_PARAMS(400000, CR8, Full, C),
 	__DEFINE_SPECIAL_MODE_PARAMS(FEC_LLRS),
-	__DEFINE_LINK_MODE_PARAMS(100000, KR, Full),
-	__DEFINE_LINK_MODE_PARAMS(100000, SR, Full),
-	__DEFINE_LINK_MODE_PARAMS(100000, LR_ER_FR, Full),
-	__DEFINE_LINK_MODE_PARAMS(100000, DR, Full),
-	__DEFINE_LINK_MODE_PARAMS(100000, CR, Full),
-	__DEFINE_LINK_MODE_PARAMS(200000, KR2, Full),
-	__DEFINE_LINK_MODE_PARAMS(200000, SR2, Full),
-	__DEFINE_LINK_MODE_PARAMS(200000, LR2_ER2_FR2, Full),
-	__DEFINE_LINK_MODE_PARAMS(200000, DR2, Full),
-	__DEFINE_LINK_MODE_PARAMS(200000, CR2, Full),
-	__DEFINE_LINK_MODE_PARAMS(400000, KR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(400000, SR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(400000, LR4_ER4_FR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(400000, DR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(400000, CR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(100, FX, Half),
-	__DEFINE_LINK_MODE_PARAMS(100, FX, Full),
-	__DEFINE_LINK_MODE_PARAMS(10, T1L, Full),
-	__DEFINE_LINK_MODE_PARAMS(800000, CR8, Full),
-	__DEFINE_LINK_MODE_PARAMS(800000, KR8, Full),
-	__DEFINE_LINK_MODE_PARAMS(800000, DR8, Full),
-	__DEFINE_LINK_MODE_PARAMS(800000, DR8_2, Full),
-	__DEFINE_LINK_MODE_PARAMS(800000, SR8, Full),
-	__DEFINE_LINK_MODE_PARAMS(800000, VR8, Full),
-	__DEFINE_LINK_MODE_PARAMS(10, T1S, Full),
-	__DEFINE_LINK_MODE_PARAMS(10, T1S, Half),
-	__DEFINE_LINK_MODE_PARAMS(10, T1S_P2MP, Half),
-	__DEFINE_LINK_MODE_PARAMS(10, T1BRR, Full),
-	__DEFINE_LINK_MODE_PARAMS(200000, CR, Full),
-	__DEFINE_LINK_MODE_PARAMS(200000, KR, Full),
-	__DEFINE_LINK_MODE_PARAMS(200000, DR, Full),
-	__DEFINE_LINK_MODE_PARAMS(200000, DR_2, Full),
-	__DEFINE_LINK_MODE_PARAMS(200000, SR, Full),
-	__DEFINE_LINK_MODE_PARAMS(200000, VR, Full),
-	__DEFINE_LINK_MODE_PARAMS(400000, CR2, Full),
-	__DEFINE_LINK_MODE_PARAMS(400000, KR2, Full),
-	__DEFINE_LINK_MODE_PARAMS(400000, DR2, Full),
-	__DEFINE_LINK_MODE_PARAMS(400000, DR2_2, Full),
-	__DEFINE_LINK_MODE_PARAMS(400000, SR2, Full),
-	__DEFINE_LINK_MODE_PARAMS(400000, VR2, Full),
-	__DEFINE_LINK_MODE_PARAMS(800000, CR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(800000, KR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(800000, DR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(800000, DR4_2, Full),
-	__DEFINE_LINK_MODE_PARAMS(800000, SR4, Full),
-	__DEFINE_LINK_MODE_PARAMS(800000, VR4, Full),
+	__DEFINE_LINK_MODE_PARAMS(100000, KR, Full, K),
+	__DEFINE_LINK_MODE_PARAMS(100000, SR, Full, S),
+	__DEFINE_LINK_MODE_PARAMS_MEDIUMS(100000, LR_ER_FR, Full,
+					  __MED(L) | __MED(E) | __MED(F)),
+	__DEFINE_LINK_MODE_PARAMS(100000, DR, Full, D),
+	__DEFINE_LINK_MODE_PARAMS(100000, CR, Full, C),
+	__DEFINE_LINK_MODE_PARAMS(200000, KR2, Full, K),
+	__DEFINE_LINK_MODE_PARAMS(200000, SR2, Full, S),
+	__DEFINE_LINK_MODE_PARAMS_MEDIUMS(200000, LR2_ER2_FR2, Full,
+					  __MED(L) | __MED(E) | __MED(F)),
+	__DEFINE_LINK_MODE_PARAMS(200000, DR2, Full, D),
+	__DEFINE_LINK_MODE_PARAMS(200000, CR2, Full, C),
+	__DEFINE_LINK_MODE_PARAMS(400000, KR4, Full, K),
+	__DEFINE_LINK_MODE_PARAMS(400000, SR4, Full, S),
+	__DEFINE_LINK_MODE_PARAMS_MEDIUMS(400000, LR4_ER4_FR4, Full,
+					  __MED(L) | __MED(E) | __MED(F)),
+	__DEFINE_LINK_MODE_PARAMS(400000, DR4, Full, D),
+	__DEFINE_LINK_MODE_PARAMS(400000, CR4, Full, C),
+	__DEFINE_LINK_MODE_PARAMS(100, FX, Half, F),
+	__DEFINE_LINK_MODE_PARAMS(100, FX, Full, F),
+	__DEFINE_LINK_MODE_PARAMS(10, T1L, Full, T),
+	__DEFINE_LINK_MODE_PARAMS(800000, CR8, Full, C),
+	__DEFINE_LINK_MODE_PARAMS(800000, KR8, Full, K),
+	__DEFINE_LINK_MODE_PARAMS(800000, DR8, Full, D),
+	__DEFINE_LINK_MODE_PARAMS(800000, DR8_2, Full, D),
+	__DEFINE_LINK_MODE_PARAMS(800000, SR8, Full, S),
+	__DEFINE_LINK_MODE_PARAMS(800000, VR8, Full, V),
+	__DEFINE_LINK_MODE_PARAMS(10, T1S, Full, T),
+	__DEFINE_LINK_MODE_PARAMS(10, T1S, Half, T),
+	__DEFINE_LINK_MODE_PARAMS(10, T1S_P2MP, Half, T),
+	__DEFINE_LINK_MODE_PARAMS(10, T1BRR, Full, T),
+	__DEFINE_LINK_MODE_PARAMS(200000, CR, Full, C),
+	__DEFINE_LINK_MODE_PARAMS(200000, KR, Full, K),
+	__DEFINE_LINK_MODE_PARAMS(200000, DR, Full, D),
+	__DEFINE_LINK_MODE_PARAMS(200000, DR_2, Full, D),
+	__DEFINE_LINK_MODE_PARAMS(200000, SR, Full, S),
+	__DEFINE_LINK_MODE_PARAMS(200000, VR, Full, V),
+	__DEFINE_LINK_MODE_PARAMS(400000, CR2, Full, C),
+	__DEFINE_LINK_MODE_PARAMS(400000, KR2, Full, K),
+	__DEFINE_LINK_MODE_PARAMS(400000, DR2, Full, D),
+	__DEFINE_LINK_MODE_PARAMS(400000, DR2_2, Full, D),
+	__DEFINE_LINK_MODE_PARAMS(400000, SR2, Full, S),
+	__DEFINE_LINK_MODE_PARAMS(400000, VR2, Full, V),
+	__DEFINE_LINK_MODE_PARAMS(800000, CR4, Full, C),
+	__DEFINE_LINK_MODE_PARAMS(800000, KR4, Full, K),
+	__DEFINE_LINK_MODE_PARAMS(800000, DR4, Full, D),
+	__DEFINE_LINK_MODE_PARAMS(800000, DR4_2, Full, D),
+	__DEFINE_LINK_MODE_PARAMS(800000, SR4, Full, S),
+	__DEFINE_LINK_MODE_PARAMS(800000, VR4, Full, V),
 };
 static_assert(ARRAY_SIZE(link_mode_params) == __ETHTOOL_LINK_MODE_MASK_NBITS);
 EXPORT_SYMBOL_GPL(link_mode_params);
 
+const char ethtool_link_medium_names[][ETH_GSTRING_LEN] = {
+	[ETHTOOL_LINK_MEDIUM_BASET] = "BaseT",
+	[ETHTOOL_LINK_MEDIUM_BASEK] = "BaseK",
+	[ETHTOOL_LINK_MEDIUM_BASES] = "BaseS",
+	[ETHTOOL_LINK_MEDIUM_BASEC] = "BaseC",
+	[ETHTOOL_LINK_MEDIUM_BASEL] = "BaseL",
+	[ETHTOOL_LINK_MEDIUM_BASED] = "BaseD",
+	[ETHTOOL_LINK_MEDIUM_BASEE] = "BaseE",
+	[ETHTOOL_LINK_MEDIUM_BASEF] = "BaseF",
+	[ETHTOOL_LINK_MEDIUM_BASEV] = "BaseV",
+	[ETHTOOL_LINK_MEDIUM_BASEMLD] = "BaseMLD",
+	[ETHTOOL_LINK_MEDIUM_NONE] = "None",
+};
+static_assert(ARRAY_SIZE(ethtool_link_medium_names) == __ETHTOOL_LINK_MEDIUM_LAST);
+EXPORT_SYMBOL_GPL(ethtool_link_medium_names);
+
 const char netif_msg_class_names[][ETH_GSTRING_LEN] = {
 	[NETIF_MSG_DRV_BIT]		= "drv",
 	[NETIF_MSG_PROBE_BIT]		= "probe",
-- 
2.49.0

[PATCH net-next v7 04/15] net: phy: Introduce PHY ports representation

[Maxime Chevallier]

Ethernet provides a wide variety of layer 1 protocols and standards for
data transmission. The front-facing ports of an interface have their own
complexity and configurability.

Introduce a representation of these front-facing ports. The current code
is minimalistic and only support ports controlled by PHY devices, but
the plan is to extend that to SFP as well as raw Ethernet MACs that
don't use PHY devices.

This minimal port representation allows describing the media and number
of lanes of a port. From that information, we can derive the linkmodes
usable on the port, which can be used to limit the capabilities of an
interface.

For now, the port lanes and medium is derived from devicetree, defined
by the PHY driver, or populated with default values (as we assume that
all PHYs expose at least one port).

The typical example is 100M ethernet. 100BaseT can work using only 2
lanes on a Cat 5 cables. However, in the situation where a 10/100/1000
capable PHY is wired to its RJ45 port through 2 lanes only, we have no
way of detecting that. The "max-speed" DT property can be used, but a
more accurate representation can be used :

mdi {
	connector-0 {
		media = "BaseT";
		lanes = <2>;
	};
};

From that information, we can derive the max speed reachable on the
port.

Another benefit of having that is to avoid vendor-specific DT properties
(micrel,fiber-mode or ti,fiber-mode).

This basic representation is meant to be expanded, by the introduction
of port ops, userspace listing of ports, and support for multi-port
devices.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
 MAINTAINERS                  |   1 +
 drivers/net/phy/Makefile     |   2 +-
 drivers/net/phy/phy-caps.h   |   5 +
 drivers/net/phy/phy_caps.c   |  58 +++++++++++
 drivers/net/phy/phy_device.c | 180 +++++++++++++++++++++++++++++++++++
 drivers/net/phy/phy_port.c   | 138 +++++++++++++++++++++++++++
 include/linux/ethtool.h      |  26 +++++
 include/linux/phy.h          |  30 ++++++
 include/linux/phy_port.h     |  96 +++++++++++++++++++
 9 files changed, 535 insertions(+), 1 deletion(-)
 create mode 100644 drivers/net/phy/phy_port.c
 create mode 100644 include/linux/phy_port.h

diff --git a/MAINTAINERS b/MAINTAINERS
index 20806cfc1003..10d7548d440e 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -8966,6 +8966,7 @@ F:	include/linux/of_net.h
 F:	include/linux/phy.h
 F:	include/linux/phy_fixed.h
 F:	include/linux/phy_link_topology.h
+F:	include/linux/phy_port.h
 F:	include/linux/phylib_stubs.h
 F:	include/linux/platform_data/mdio-bcm-unimac.h
 F:	include/linux/platform_data/mdio-gpio.h
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index b4795aaf9c1c..b4207d7d092a 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -3,7 +3,7 @@
 
 libphy-y			:= phy.o phy-c45.o phy-core.o phy_device.o \
 				   linkmode.o phy_link_topology.o \
-				   phy_caps.o mdio_bus_provider.o
+				   phy_caps.o mdio_bus_provider.o phy_port.o
 mdio-bus-y			+= mdio_bus.o mdio_device.o
 
 ifdef CONFIG_PHYLIB
diff --git a/drivers/net/phy/phy-caps.h b/drivers/net/phy/phy-caps.h
index 157759966650..01df1bdc1516 100644
--- a/drivers/net/phy/phy-caps.h
+++ b/drivers/net/phy/phy-caps.h
@@ -60,4 +60,9 @@ const struct link_capabilities *
 phy_caps_lookup(int speed, unsigned int duplex, const unsigned long *supported,
 		bool exact);
 
+void phy_caps_medium_get_supported(unsigned long *supported,
+				   enum ethtool_link_medium medium,
+				   int lanes);
+u32 phy_caps_mediums_from_linkmodes(unsigned long *linkmodes);
+
 #endif /* __PHY_CAPS_H */
diff --git a/drivers/net/phy/phy_caps.c b/drivers/net/phy/phy_caps.c
index d11ce1c7e712..5a4a1d6173ca 100644
--- a/drivers/net/phy/phy_caps.c
+++ b/drivers/net/phy/phy_caps.c
@@ -372,3 +372,61 @@ unsigned long phy_caps_from_interface(phy_interface_t interface)
 	return link_caps;
 }
 EXPORT_SYMBOL_GPL(phy_caps_from_interface);
+
+/**
+ * phy_caps_medium_get_supported() - Returns linkmodes supported on a given medium
+ * @supported: After this call, contains all possible linkmodes on a given medium,
+ *	       and with the given number of lanes.
+ * @medium: The medium to get the support from
+ * @lanes: The number of lanes used on the given medium
+ *
+ * If no match exists, the supported field is left untouched.
+ */
+void phy_caps_medium_get_supported(unsigned long *supported,
+				   enum ethtool_link_medium medium,
+				   int lanes)
+{
+	int i;
+
+	for (i = 0; i < __ETHTOOL_LINK_MODE_MASK_NBITS; i++) {
+		/* Special bits such as Autoneg, Pause, Asym_pause, etc. are
+		 * set and will be masked away by the port parent.
+		 */
+		if (link_mode_params[i].mediums == BIT(ETHTOOL_LINK_MEDIUM_NONE)) {
+			linkmode_set_bit(i, supported);
+			continue;
+		}
+
+		/* For most cases, min_lanes == lanes, except for 10/100BaseT that work
+		 * on 2 lanes but are compatible with 4 lanes mediums
+		 */
+		if (link_mode_params[i].mediums & BIT(medium) &&
+		    link_mode_params[i].lanes >= lanes &&
+		    link_mode_params[i].min_lanes <= lanes) {
+			linkmode_set_bit(i, supported);
+		}
+	}
+}
+EXPORT_SYMBOL_GPL(phy_caps_medium_get_supported);
+
+/**
+ * phy_caps_mediums_from_linkmodes() - Get all mediums from a linkmodes list
+ * @linkmodes: A bitset of linkmodes to get the mediums from
+ *
+ * Returns: A bitset of ETHTOOL_MEDIUM_XXX values corresponding to all medium
+ *	    types in the linkmodes list
+ */
+u32 phy_caps_mediums_from_linkmodes(unsigned long *linkmodes)
+{
+	const struct link_mode_info *linkmode;
+	u32 mediums = 0;
+	int i;
+
+	for_each_set_bit(i, linkmodes, __ETHTOOL_LINK_MODE_MASK_NBITS) {
+		linkmode = &link_mode_params[i];
+		mediums |= linkmode->mediums;
+	}
+
+	return mediums;
+}
+EXPORT_SYMBOL_GPL(phy_caps_mediums_from_linkmodes);
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index 90951681523c..4ec21c31e6c6 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -30,6 +30,7 @@
 #include <linux/phylib_stubs.h>
 #include <linux/phy_led_triggers.h>
 #include <linux/phy_link_topology.h>
+#include <linux/phy_port.h>
 #include <linux/pse-pd/pse.h>
 #include <linux/property.h>
 #include <linux/ptp_clock_kernel.h>
@@ -836,6 +837,13 @@ struct phy_device *phy_device_create(struct mii_bus *bus, int addr, u32 phy_id,
 
 	dev->state = PHY_DOWN;
 	INIT_LIST_HEAD(&dev->leds);
+	INIT_LIST_HEAD(&dev->ports);
+
+	/* The driver's probe function must change that to the real number
+	 * of ports possible on the PHY. We assume by default we are dealing
+	 * with a single-port PHY
+	 */
+	dev->max_n_ports = 1;
 
 	mutex_init(&dev->lock);
 	INIT_DELAYED_WORK(&dev->state_queue, phy_state_machine);
@@ -1579,6 +1587,46 @@ void phy_sfp_detach(void *upstream, struct sfp_bus *bus)
 }
 EXPORT_SYMBOL(phy_sfp_detach);
 
+static int phy_add_port(struct phy_device *phydev, struct phy_port *port)
+{
+	int ret = 0;
+
+	if (phydev->n_ports == phydev->max_n_ports)
+		return -EBUSY;
+
+	/* We set all ports as active by default, PHY drivers may deactivate
+	 * them (when unused)
+	 */
+	port->active = true;
+
+	if (phydev->drv && phydev->drv->attach_port)
+		ret = phydev->drv->attach_port(phydev, port);
+
+	if (ret)
+		return ret;
+
+	/* The PHY driver might have added, removed or set medium/lanes info,
+	 * so update the port supported accordingly.
+	 */
+	phy_port_update_supported(port);
+
+	list_add(&port->head, &phydev->ports);
+
+	phydev->n_ports++;
+
+	return 0;
+}
+
+static void phy_del_port(struct phy_device *phydev, struct phy_port *port)
+{
+	if (!phydev->n_ports)
+		return;
+
+	list_del(&port->head);
+
+	phydev->n_ports--;
+}
+
 /**
  * phy_sfp_probe - probe for a SFP cage attached to this PHY device
  * @phydev: Pointer to phy_device
@@ -3312,6 +3360,131 @@ static int of_phy_leds(struct phy_device *phydev)
 	return 0;
 }
 
+static void phy_cleanup_ports(struct phy_device *phydev)
+{
+	struct phy_port *tmp, *port;
+
+	list_for_each_entry_safe(port, tmp, &phydev->ports, head) {
+		phy_del_port(phydev, port);
+		phy_port_destroy(port);
+	}
+}
+
+static int phy_default_setup_single_port(struct phy_device *phydev)
+{
+	struct phy_port *port = phy_port_alloc();
+
+	if (!port)
+		return -ENOMEM;
+
+	port->parent_type = PHY_PORT_PHY;
+	port->phy = phydev;
+
+	/* Let the PHY driver know that this port was never described anywhere.
+	 * This is the usual case, where we assume single-port PHY devices with
+	 * no SFP. In that case, the port supports exactly the same thing as
+	 * the PHY itself.
+	 *
+	 * However, this can also be because we have a combo-port PHY, with
+	 * only one port described in DT, through SFP for example.
+	 *
+	 * In that case, the PHY driver will be in charge of saying what we can
+	 * do on that non-represented port.
+	 */
+	port->not_described = true;
+	linkmode_copy(port->supported, phydev->supported);
+	port->mediums = phy_caps_mediums_from_linkmodes(port->supported);
+
+	phy_add_port(phydev, port);
+
+	return 0;
+}
+
+static int of_phy_ports(struct phy_device *phydev)
+{
+	struct device_node *node = phydev->mdio.dev.of_node;
+	struct device_node *mdi;
+	struct phy_port *port;
+	int err;
+
+	if (!IS_ENABLED(CONFIG_OF_MDIO))
+		return 0;
+
+	if (!node)
+		return 0;
+
+	mdi = of_get_child_by_name(node, "mdi");
+	if (!mdi)
+		return 0;
+
+	for_each_available_child_of_node_scoped(mdi, port_node) {
+		port = phy_of_parse_port(port_node);
+		if (IS_ERR(port)) {
+			err = PTR_ERR(port);
+			goto out_err;
+		}
+
+		port->parent_type = PHY_PORT_PHY;
+		port->phy = phydev;
+		err = phy_add_port(phydev, port);
+		if (err)
+			goto out_err;
+	}
+	of_node_put(mdi);
+
+	return 0;
+
+out_err:
+	phy_cleanup_ports(phydev);
+	of_node_put(mdi);
+	return err;
+}
+
+static int phy_setup_ports(struct phy_device *phydev)
+{
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(ports_supported);
+	struct phy_port *port;
+	int ret;
+
+	ret = of_phy_ports(phydev);
+	if (ret)
+		return ret;
+
+	if (phydev->n_ports < phydev->max_n_ports) {
+		ret = phy_default_setup_single_port(phydev);
+		if (ret)
+			goto out;
+	}
+
+	linkmode_zero(ports_supported);
+
+	/* Aggregate the supported modes, which are made-up of :
+	 *  - What the PHY itself supports
+	 *  - What the sum of all ports support
+	 */
+	list_for_each_entry(port, &phydev->ports, head)
+		if (port->active)
+			linkmode_or(ports_supported, ports_supported,
+				    port->supported);
+
+	if (!linkmode_empty(ports_supported))
+		linkmode_and(phydev->supported, phydev->supported,
+			     ports_supported);
+
+	/* For now, the phy->port field is set as the first active port's type */
+	list_for_each_entry(port, &phydev->ports, head)
+		if (port->active) {
+			phydev->port = phy_port_get_type(port);
+			break;
+		}
+
+	return 0;
+
+out:
+	phy_cleanup_ports(phydev);
+	return ret;
+}
+
 /**
  * fwnode_mdio_find_device - Given a fwnode, find the mdio_device
  * @fwnode: pointer to the mdio_device's fwnode
@@ -3449,6 +3622,11 @@ static int phy_probe(struct device *dev)
 		phydev->is_gigabit_capable = 1;
 
 	of_set_phy_supported(phydev);
+
+	err = phy_setup_ports(phydev);
+	if (err)
+		goto out;
+
 	phy_advertise_supported(phydev);
 
 	/* Get PHY default EEE advertising modes and handle them as potentially
@@ -3524,6 +3702,8 @@ static int phy_remove(struct device *dev)
 
 	phydev->state = PHY_DOWN;
 
+	phy_cleanup_ports(phydev);
+
 	sfp_bus_del_upstream(phydev->sfp_bus);
 	phydev->sfp_bus = NULL;
 
diff --git a/drivers/net/phy/phy_port.c b/drivers/net/phy/phy_port.c
new file mode 100644
index 000000000000..f9a1c3d21f78
--- /dev/null
+++ b/drivers/net/phy/phy_port.c
@@ -0,0 +1,138 @@
+// SPDX-License-Identifier: GPL-2.0+
+/* Framework to drive Ethernet ports
+ *
+ * Copyright (c) 2024 Maxime Chevallier <maxime.chevallier@bootlin.com>
+ */
+
+#include <linux/linkmode.h>
+#include <linux/of.h>
+#include <linux/phy_port.h>
+
+#include "phy-caps.h"
+
+/**
+ * phy_port_alloc() - Allocate a new phy_port
+ *
+ * Returns: a newly allocated struct phy_port, or NULL.
+ */
+struct phy_port *phy_port_alloc(void)
+{
+	struct phy_port *port;
+
+	port = kzalloc(sizeof(*port), GFP_KERNEL);
+	if (!port)
+		return NULL;
+
+	linkmode_zero(port->supported);
+	INIT_LIST_HEAD(&port->head);
+
+	return port;
+}
+EXPORT_SYMBOL_GPL(phy_port_alloc);
+
+/**
+ * phy_port_destroy() - Free a struct phy_port
+ * @port: The port to destroy
+ */
+void phy_port_destroy(struct phy_port *port)
+{
+	kfree(port);
+}
+EXPORT_SYMBOL_GPL(phy_port_destroy);
+
+/**
+ * phy_of_parse_port() - Create a phy_port from a firmware representation
+ * @dn: device_node representation of the port, following the
+ *	ethernet-connector.yaml binding
+ *
+ * Returns: a newly allocated and initialized phy_port pointer, or an ERR_PTR.
+ */
+struct phy_port *phy_of_parse_port(struct device_node *dn)
+{
+	struct fwnode_handle *fwnode = of_fwnode_handle(dn);
+	enum ethtool_link_medium medium;
+	struct phy_port *port;
+	struct property *prop;
+	const char *med_str;
+	u32 lanes, mediums = 0;
+	int ret;
+
+	ret = fwnode_property_read_u32(fwnode, "lanes", &lanes);
+	if (ret)
+		lanes = 0;
+
+	ret = fwnode_property_read_string(fwnode, "media", &med_str);
+	if (ret)
+		return ERR_PTR(ret);
+
+	of_property_for_each_string(to_of_node(fwnode), "media", prop, med_str) {
+		medium = ethtool_str_to_medium(med_str);
+		if (medium == ETHTOOL_LINK_MEDIUM_NONE)
+			return ERR_PTR(-EINVAL);
+
+		mediums |= BIT(medium);
+	}
+
+	if (!mediums)
+		return ERR_PTR(-EINVAL);
+
+	port = phy_port_alloc();
+	if (!port)
+		return ERR_PTR(-ENOMEM);
+
+	port->lanes = lanes;
+	port->mediums = mediums;
+
+	return port;
+}
+EXPORT_SYMBOL_GPL(phy_of_parse_port);
+
+/**
+ * phy_port_update_supported() - Setup the port->supported field
+ * @port: the port to update
+ *
+ * Once the port's medium list and number of lanes has been configured based
+ * on firmware, straps and vendor-specific properties, this function may be
+ * called to update the port's supported linkmodes list.
+ *
+ * Any mode that was manually set in the port's supported list remains set.
+ */
+void phy_port_update_supported(struct phy_port *port)
+{
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(supported) = { 0 };
+	int i, lanes = 1;
+
+	/* If there's no lanes specified, we grab the default number of
+	 * lanes as the max of the default lanes for each medium
+	 */
+	if (!port->lanes)
+		for_each_set_bit(i, &port->mediums, __ETHTOOL_LINK_MEDIUM_LAST)
+			lanes = max_t(int, lanes, phy_medium_default_lanes(i));
+
+	port->lanes = lanes;
+
+	for_each_set_bit(i, &port->mediums, __ETHTOOL_LINK_MEDIUM_LAST) {
+		linkmode_zero(supported);
+		phy_caps_medium_get_supported(supported, i, port->lanes);
+		linkmode_or(port->supported, port->supported, supported);
+	}
+}
+EXPORT_SYMBOL_GPL(phy_port_update_supported);
+
+/**
+ * phy_port_get_type() - get the PORT_* attribut for that port.
+ * @port: The port we want the information from
+ *
+ * Returns: A PORT_XXX value.
+ */
+int phy_port_get_type(struct phy_port *port)
+{
+	if (port->mediums & ETHTOOL_LINK_MEDIUM_BASET)
+		return PORT_TP;
+
+	if (phy_port_is_fiber(port))
+		return PORT_FIBRE;
+
+	return PORT_OTHER;
+}
+EXPORT_SYMBOL_GPL(phy_port_get_type);
diff --git a/include/linux/ethtool.h b/include/linux/ethtool.h
index 4db968201f68..3fd14e7c3099 100644
--- a/include/linux/ethtool.h
+++ b/include/linux/ethtool.h
@@ -227,6 +227,10 @@ extern const struct link_mode_info link_mode_params[];
 
 extern const char ethtool_link_medium_names[][ETH_GSTRING_LEN];
 
+#define ETHTOOL_MEDIUM_FIBER_BITS (BIT(ETHTOOL_LINK_MEDIUM_BASES) | \
+				   BIT(ETHTOOL_LINK_MEDIUM_BASEL) | \
+				   BIT(ETHTOOL_LINK_MEDIUM_BASEF))
+
 static inline const char *phy_mediums(enum ethtool_link_medium medium)
 {
 	if (medium >= __ETHTOOL_LINK_MEDIUM_LAST)
@@ -235,6 +239,28 @@ static inline const char *phy_mediums(enum ethtool_link_medium medium)
 	return ethtool_link_medium_names[medium];
 }
 
+static inline enum ethtool_link_medium ethtool_str_to_medium(const char *str)
+{
+	int i;
+
+	for (i = 0; i < __ETHTOOL_LINK_MEDIUM_LAST; i++)
+		if (!strcmp(phy_mediums(i), str))
+			return i;
+
+	return ETHTOOL_LINK_MEDIUM_NONE;
+}
+
+static inline int phy_medium_default_lanes(enum ethtool_link_medium medium)
+{
+	/* Let's consider that the default BaseT ethernet is BaseT4, i.e.
+	 * Gigabit Ethernet.
+	 */
+	if (medium == ETHTOOL_LINK_MEDIUM_BASET)
+		return 4;
+
+	return 1;
+}
+
 /* declare a link mode bitmap */
 #define __ETHTOOL_DECLARE_LINK_MODE_MASK(name)		\
 	DECLARE_BITMAP(name, __ETHTOOL_LINK_MODE_MASK_NBITS)
diff --git a/include/linux/phy.h b/include/linux/phy.h
index 74c1bcf64b3c..89cb4fb6d7f9 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -313,6 +313,7 @@ static inline long rgmii_clock(int speed)
 struct device;
 struct kernel_hwtstamp_config;
 struct phylink;
+struct phy_port;
 struct sfp_bus;
 struct sfp_upstream_ops;
 struct sk_buff;
@@ -605,6 +606,9 @@ struct macsec_ops;
  * @master_slave_state: Current master/slave configuration
  * @mii_ts: Pointer to time stamper callbacks
  * @psec: Pointer to Power Sourcing Equipment control struct
+ * @ports: List of PHY ports structures
+ * @n_ports: Number of ports currently attached to the PHY
+ * @max_n_ports: Max number of ports this PHY can expose
  * @lock:  Mutex for serialization access to PHY
  * @state_queue: Work queue for state machine
  * @link_down_events: Number of times link was lost
@@ -740,6 +744,10 @@ struct phy_device {
 	struct mii_timestamper *mii_ts;
 	struct pse_control *psec;
 
+	struct list_head ports;
+	int n_ports;
+	int max_n_ports;
+
 	u8 mdix;
 	u8 mdix_ctrl;
 
@@ -1256,6 +1264,27 @@ struct phy_driver {
 	 * Returns the time in jiffies until the next update event.
 	 */
 	unsigned int (*get_next_update_time)(struct phy_device *dev);
+
+	/**
+	 * @attach_port: Indicates to the PHY driver that a port is detected
+	 * @dev: PHY device to notify
+	 * @port: The port being added
+	 *
+	 * Called when a port that needs to be driven by the PHY is found. The
+	 * number of time this will be called depends on phydev->max_n_ports,
+	 * which the driver can change in .probe().
+	 *
+	 * The port that is being passed may or may not be initialized. If it is
+	 * already initialized, it is by the generic port representation from
+	 * devicetree, which superseeds any strapping or vendor-specific
+	 * properties.
+	 *
+	 * If the port isn't initialized, the port->mediums and port->lanes
+	 * fields must be set, possibly according to stapping information.
+	 *
+	 * Returns 0, or an error code.
+	 */
+	int (*attach_port)(struct phy_device *dev, struct phy_port *port);
 };
 #define to_phy_driver(d) container_of_const(to_mdio_common_driver(d),		\
 				      struct phy_driver, mdiodrv)
@@ -1993,6 +2022,7 @@ void phy_trigger_machine(struct phy_device *phydev);
 void phy_mac_interrupt(struct phy_device *phydev);
 void phy_start_machine(struct phy_device *phydev);
 void phy_stop_machine(struct phy_device *phydev);
+
 void phy_ethtool_ksettings_get(struct phy_device *phydev,
 			       struct ethtool_link_ksettings *cmd);
 int phy_ethtool_ksettings_set(struct phy_device *phydev,
diff --git a/include/linux/phy_port.h b/include/linux/phy_port.h
new file mode 100644
index 000000000000..f47ac5f5ef9e
--- /dev/null
+++ b/include/linux/phy_port.h
@@ -0,0 +1,96 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+
+#ifndef __PHY_PORT_H
+#define __PHY_PORT_H
+
+#include <linux/ethtool.h>
+#include <linux/types.h>
+#include <linux/phy.h>
+
+struct phy_port;
+
+/**
+ * enum phy_port_parent - The device this port is attached to
+ *
+ * @PHY_PORT_PHY: Indicates that the port is driven by a PHY device
+ */
+enum phy_port_parent {
+	PHY_PORT_PHY,
+};
+
+struct phy_port_ops {
+	/* Sometimes, the link state can be retrieved from physical,
+	 * out-of-band channels such as the LOS signal on SFP. These
+	 * callbacks allows notifying the port about state changes
+	 */
+	void (*link_up)(struct phy_port *port);
+	void (*link_down)(struct phy_port *port);
+
+	/* If the port acts as a Media Independent Interface (Serdes port),
+	 * configures the port with the relevant state and mode. When enable is
+	 * not set, interface should be ignored
+	 */
+	int (*configure_mii)(struct phy_port *port, bool enable, phy_interface_t interface);
+};
+
+/**
+ * struct phy_port - A representation of a network device physical interface
+ *
+ * @head: Used by the port's parent to list ports
+ * @parent_type: The type of device this port is directly connected to
+ * @phy: If the parent is PHY_PORT_PHYDEV, the PHY controlling that port
+ * @ops: Callback ops implemented by the port controller
+ * @lanes: The number of lanes (diff pairs) this port has, 0 if not applicable
+ * @mediums: Bitmask of the physical mediums this port provides access to
+ * @supported: The link modes this port can expose, if this port is MDI (not MII)
+ * @interfaces: The MII interfaces this port supports, if this port is MII
+ * @not_described: Indicates to the parent driver if this port isn't described,
+ *		   so it's up to the parent to filter its capabilities.
+ * @active: Indicates if the port is currently part of the active link.
+ * @is_mii: Indicates if this port is MII (Media Independent Interface),
+ *          or MDI (Media Dependent Interface).
+ */
+struct phy_port {
+	struct list_head head;
+	enum phy_port_parent parent_type;
+	union {
+		struct phy_device *phy;
+	};
+
+	const struct phy_port_ops *ops;
+
+	int lanes;
+	unsigned long mediums;
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(supported);
+	DECLARE_PHY_INTERFACE_MASK(interfaces);
+
+	unsigned int not_described:1;
+	unsigned int active:1;
+	unsigned int is_mii:1;
+};
+
+struct phy_port *phy_port_alloc(void);
+void phy_port_destroy(struct phy_port *port);
+
+static inline struct phy_device *port_phydev(struct phy_port *port)
+{
+	return port->phy;
+}
+
+struct phy_port *phy_of_parse_port(struct device_node *dn);
+
+static inline bool phy_port_is_copper(struct phy_port *port)
+{
+	return port->mediums == BIT(ETHTOOL_LINK_MEDIUM_BASET);
+}
+
+static inline bool phy_port_is_fiber(struct phy_port *port)
+{
+	return !!(port->mediums & ETHTOOL_MEDIUM_FIBER_BITS);
+}
+
+void phy_port_update_supported(struct phy_port *port);
+
+int phy_port_get_type(struct phy_port *port);
+
+#endif
-- 
2.49.0

[PATCH net-next v7 05/15] net: phy: dp83822: Add support for phy_port representation

[Maxime Chevallier]

With the phy_port representation intrduced, we can use .attach_port to
populate the port information based on either the straps or the
ti,fiber-mode property. This allows simplifying the probe function and
allow users to override the strapping configuration.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
 drivers/net/phy/dp83822.c | 71 +++++++++++++++++++++++++--------------
 1 file changed, 45 insertions(+), 26 deletions(-)

diff --git a/drivers/net/phy/dp83822.c b/drivers/net/phy/dp83822.c
index 33db21251f2e..2657be2e9034 100644
--- a/drivers/net/phy/dp83822.c
+++ b/drivers/net/phy/dp83822.c
@@ -11,6 +11,7 @@
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/phy.h>
+#include <linux/phy_port.h>
 #include <linux/netdevice.h>
 #include <linux/bitfield.h>
 
@@ -811,17 +812,6 @@ static int dp83822_of_init(struct phy_device *phydev)
 	int i, ret;
 	u32 val;
 
-	/* Signal detection for the PHY is only enabled if the FX_EN and the
-	 * SD_EN pins are strapped. Signal detection can only enabled if FX_EN
-	 * is strapped otherwise signal detection is disabled for the PHY.
-	 */
-	if (dp83822->fx_enabled && dp83822->fx_sd_enable)
-		dp83822->fx_signal_det_low = device_property_present(dev,
-								     "ti,link-loss-low");
-	if (!dp83822->fx_enabled)
-		dp83822->fx_enabled = device_property_present(dev,
-							      "ti,fiber-mode");
-
 	if (!device_property_read_string(dev, "ti,gpio2-clk-out", &of_val)) {
 		if (strcmp(of_val, "mac-if") == 0) {
 			dp83822->gpio2_clk_out = DP83822_CLK_SRC_MAC_IF;
@@ -950,6 +940,48 @@ static int dp83822_read_straps(struct phy_device *phydev)
 	return 0;
 }
 
+static int dp83822_attach_port(struct phy_device *phydev, struct phy_port *port)
+{
+	struct dp83822_private *dp83822 = phydev->priv;
+	int ret;
+
+	if (port->mediums) {
+		if (phy_port_is_fiber(port))
+			dp83822->fx_enabled = true;
+	} else {
+		ret = dp83822_read_straps(phydev);
+		if (ret)
+			return ret;
+
+#if IS_ENABLED(CONFIG_OF_MDIO)
+		if (dp83822->fx_enabled && dp83822->fx_sd_enable)
+			dp83822->fx_signal_det_low =
+				device_property_present(&phydev->mdio.dev,
+							"ti,link-loss-low");
+
+		/* ti,fiber-mode is still used for backwards compatibility, but
+		 * has been replaced with the mdi node definition, see
+		 * ethernet-port.yaml
+		 */
+		if (!dp83822->fx_enabled)
+			dp83822->fx_enabled =
+				device_property_present(&phydev->mdio.dev,
+							"ti,fiber-mode");
+#endif /* CONFIG_OF_MDIO */
+
+		if (dp83822->fx_enabled) {
+			port->lanes = 1;
+			port->mediums = BIT(ETHTOOL_LINK_MEDIUM_BASEF);
+		} else {
+			/* This PHY can only to 100BaseTX max, so on 2 lanes */
+			port->lanes = 2;
+			port->mediums = BIT(ETHTOOL_LINK_MEDIUM_BASET);
+		}
+	}
+
+	return 0;
+}
+
 static int dp8382x_probe(struct phy_device *phydev)
 {
 	struct dp83822_private *dp83822;
@@ -968,27 +1000,13 @@ static int dp8382x_probe(struct phy_device *phydev)
 
 static int dp83822_probe(struct phy_device *phydev)
 {
-	struct dp83822_private *dp83822;
 	int ret;
 
 	ret = dp8382x_probe(phydev);
 	if (ret)
 		return ret;
 
-	dp83822 = phydev->priv;
-
-	ret = dp83822_read_straps(phydev);
-	if (ret)
-		return ret;
-
-	ret = dp83822_of_init(phydev);
-	if (ret)
-		return ret;
-
-	if (dp83822->fx_enabled)
-		phydev->port = PORT_FIBRE;
-
-	return 0;
+	return dp83822_of_init(phydev);
 }
 
 static int dp83826_probe(struct phy_device *phydev)
@@ -1172,6 +1190,7 @@ static int dp83822_led_hw_control_get(struct phy_device *phydev, u8 index,
 		.led_hw_is_supported = dp83822_led_hw_is_supported,	\
 		.led_hw_control_set = dp83822_led_hw_control_set,	\
 		.led_hw_control_get = dp83822_led_hw_control_get,	\
+		.attach_port = dp83822_attach_port		\
 	}
 
 #define DP83825_PHY_DRIVER(_id, _name)				\
-- 
2.49.0

[PATCH net-next v7 06/15] net: phy: Create a phy_port for PHY-driven SFPs

[Maxime Chevallier]

Some PHY devices may be used as media-converters to drive SFP ports (for
example, to allow using SFP when the SoC can only output RGMII). This is
already supported to some extend by allowing PHY drivers to registers
themselves as being SFP upstream.

However, the logic to drive the SFP can actually be split to a per-port
control logic, allowing support for multi-port PHYs, or PHYs that can
either drive SFPs or Copper.

To that extent, create a phy_port when registering an SFP bus onto a
PHY. This port is considered a "serdes" port, in that it can feed data
to anther entity on the link. The PHY driver needs to specify the
various PHY_INTERFACE_MODE_XXX that this port supports.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
 drivers/net/phy/phy_device.c | 24 ++++++++++++++++++++++++
 drivers/net/phy/phy_port.c   | 15 +++++++++++++++
 2 files changed, 39 insertions(+)

diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index 4ec21c31e6c6..e491d3de0189 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -1627,6 +1627,26 @@ static void phy_del_port(struct phy_device *phydev, struct phy_port *port)
 	phydev->n_ports--;
 }
 
+static int phy_setup_sfp_port(struct phy_device *phydev)
+{
+	struct phy_port *port = phy_port_alloc();
+
+	if (!port)
+		return -ENOMEM;
+
+	port->parent_type = PHY_PORT_PHY;
+	port->phy = phydev;
+
+	/* The PHY is a media converter, the port connected to the SFP cage
+	 * is a MII port.
+	 */
+	port->is_mii = true;
+
+	phy_add_port(phydev, port);
+
+	return 0;
+}
+
 /**
  * phy_sfp_probe - probe for a SFP cage attached to this PHY device
  * @phydev: Pointer to phy_device
@@ -1648,6 +1668,10 @@ int phy_sfp_probe(struct phy_device *phydev,
 		ret = sfp_bus_add_upstream(bus, phydev, ops);
 		sfp_bus_put(bus);
 	}
+
+	if (phydev->sfp_bus)
+		ret = phy_setup_sfp_port(phydev);
+
 	return ret;
 }
 EXPORT_SYMBOL(phy_sfp_probe);
diff --git a/drivers/net/phy/phy_port.c b/drivers/net/phy/phy_port.c
index f9a1c3d21f78..2c5ae947d759 100644
--- a/drivers/net/phy/phy_port.c
+++ b/drivers/net/phy/phy_port.c
@@ -116,6 +116,21 @@ void phy_port_update_supported(struct phy_port *port)
 		phy_caps_medium_get_supported(supported, i, port->lanes);
 		linkmode_or(port->supported, port->supported, supported);
 	}
+
+	/* Serdes ports supported may through SFP may not have any medium set,
+	 * as they will output PHY_INTERFACE_MODE_XXX modes. In that case, derive
+	 * the supported list based on these interfaces
+	 */
+	if (port->is_mii && linkmode_empty(supported)) {
+		unsigned long interface, link_caps = 0;
+
+		/* Get each interface's caps */
+		for_each_set_bit(interface, port->interfaces,
+				 PHY_INTERFACE_MODE_MAX)
+			link_caps |= phy_caps_from_interface(interface);
+
+		phy_caps_linkmodes(link_caps, port->supported);
+	}
 }
 EXPORT_SYMBOL_GPL(phy_port_update_supported);
 
-- 
2.49.0

[PATCH net-next v7 07/15] net: phy: Introduce generic SFP handling for PHY drivers

[Maxime Chevallier]

There are currently 4 PHY drivers that can drive downstream SFPs:
marvell.c, marvell10g.c, at803x.c and marvell-88x2222.c. Most of the
logic is boilerplate, either calling into generic phylib helpers (for
SFP PHY attach, bus attach, etc.) or performing the same tasks with a
bit of validation :
 - Getting the module's expected interface mode
 - Making sure the PHY supports it
 - Optionnaly perform some configuration to make sure the PHY outputs
   the right mode

This can be made more generic by leveraging the phy_port, and its
configure_mii() callback which allows setting a port's interfaces when
the port is a serdes.

Introduce a generic PHY SFP support. If a driver doesn't probe the SFP
bus itself, but an SFP phandle is found in devicetree/firmware, then the
generic PHY SFP support will be used, relying on port ops.

PHY driver need to :
 - Register a .attach_port() callback
 - When a serdes port is registered to the PHY, drivers must set
   port->interfaces to the set of PHY_INTERFACE_MODE the port can output
 - If the port has limitations regarding speed, duplex and aneg, the
   port can also fine-tune the final linkmodes that can be supported
 - The port may register a set of ops, including .configure_mii(), that
   will be called at module_insert time to adjust the interface based on
   the module detected.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
 drivers/net/phy/phy_device.c | 107 +++++++++++++++++++++++++++++++++++
 include/linux/phy.h          |   2 +
 2 files changed, 109 insertions(+)

diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index e491d3de0189..5a037e78a761 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -1587,6 +1587,87 @@ void phy_sfp_detach(void *upstream, struct sfp_bus *bus)
 }
 EXPORT_SYMBOL(phy_sfp_detach);
 
+static int phy_sfp_module_insert(void *upstream, const struct sfp_eeprom_id *id)
+{
+	struct phy_device *phydev = upstream;
+	struct phy_port *port = phy_get_sfp_port(phydev);
+
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(sfp_support);
+	DECLARE_PHY_INTERFACE_MASK(interfaces);
+	phy_interface_t iface;
+
+	linkmode_zero(sfp_support);
+
+	if (!port)
+		return -EINVAL;
+
+	sfp_parse_support(phydev->sfp_bus, id, sfp_support, interfaces);
+
+	if (phydev->n_ports == 1)
+		phydev->port = sfp_parse_port(phydev->sfp_bus, id, sfp_support);
+
+	linkmode_and(sfp_support, port->supported, sfp_support);
+
+	if (linkmode_empty(sfp_support)) {
+		dev_err(&phydev->mdio.dev, "incompatible SFP module inserted\n");
+		return -EINVAL;
+	}
+
+	iface = sfp_select_interface(phydev->sfp_bus, sfp_support);
+
+	/* Check that this interface is supported */
+	if (!test_bit(iface, port->interfaces)) {
+		dev_err(&phydev->mdio.dev, "incompatible SFP module inserted\n");
+		return -EINVAL;
+	}
+
+	if (port->ops && port->ops->configure_mii)
+		return port->ops->configure_mii(port, true, iface);
+
+	return 0;
+}
+
+static void phy_sfp_module_remove(void *upstream)
+{
+	struct phy_device *phydev = upstream;
+	struct phy_port *port = phy_get_sfp_port(phydev);
+
+	if (port && port->ops && port->ops->configure_mii)
+		port->ops->configure_mii(port, false, PHY_INTERFACE_MODE_NA);
+
+	if (phydev->n_ports == 1)
+		phydev->port = PORT_NONE;
+}
+
+static void phy_sfp_link_up(void *upstream)
+{
+	struct phy_device *phydev = upstream;
+	struct phy_port *port = phy_get_sfp_port(phydev);
+
+	if (port && port->ops && port->ops->link_up)
+		port->ops->link_up(port);
+}
+
+static void phy_sfp_link_down(void *upstream)
+{
+	struct phy_device *phydev = upstream;
+	struct phy_port *port = phy_get_sfp_port(phydev);
+
+	if (port && port->ops && port->ops->link_down)
+		port->ops->link_down(port);
+}
+
+static const struct sfp_upstream_ops sfp_phydev_ops = {
+	.attach = phy_sfp_attach,
+	.detach = phy_sfp_detach,
+	.module_insert = phy_sfp_module_insert,
+	.module_remove = phy_sfp_module_remove,
+	.link_up = phy_sfp_link_up,
+	.link_down = phy_sfp_link_down,
+	.connect_phy = phy_sfp_connect_phy,
+	.disconnect_phy = phy_sfp_disconnect_phy,
+};
+
 static int phy_add_port(struct phy_device *phydev, struct phy_port *port)
 {
 	int ret = 0;
@@ -3474,6 +3555,13 @@ static int phy_setup_ports(struct phy_device *phydev)
 	if (ret)
 		return ret;
 
+	/* Use generic SFP probing only if the driver didn't do so already */
+	if (!phydev->sfp_bus) {
+		ret = phy_sfp_probe(phydev, &sfp_phydev_ops);
+		if (ret)
+			goto out;
+	}
+
 	if (phydev->n_ports < phydev->max_n_ports) {
 		ret = phy_default_setup_single_port(phydev);
 		if (ret)
@@ -3509,6 +3597,25 @@ static int phy_setup_ports(struct phy_device *phydev)
 	return ret;
 }
 
+/**
+ * phy_get_sfp_port() - Returns the first valid SFP port of a PHY
+ * @phydev: pointer to the PHY device to get the SFP port from
+ *
+ * Returns: The first active SFP (serdes) port of a PHY device, NULL if none
+ * exist.
+ */
+struct phy_port *phy_get_sfp_port(struct phy_device *phydev)
+{
+	struct phy_port *port;
+
+	list_for_each_entry(port, &phydev->ports, head)
+		if (port->active && port->is_mii)
+			return port;
+
+	return NULL;
+}
+EXPORT_SYMBOL_GPL(phy_get_sfp_port);
+
 /**
  * fwnode_mdio_find_device - Given a fwnode, find the mdio_device
  * @fwnode: pointer to the mdio_device's fwnode
diff --git a/include/linux/phy.h b/include/linux/phy.h
index 89cb4fb6d7f9..03548cc55aa8 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -2113,6 +2113,8 @@ int __phy_hwtstamp_set(struct phy_device *phydev,
 		       struct kernel_hwtstamp_config *config,
 		       struct netlink_ext_ack *extack);
 
+struct phy_port *phy_get_sfp_port(struct phy_device *phydev);
+
 extern const struct bus_type mdio_bus_type;
 extern const struct class mdio_bus_class;
 
-- 
2.49.0

[PATCH net-next v7 08/15] net: phy: marvell-88x2222: Support SFP through phy_port interface

[Maxime Chevallier]

The 88x2222 PHY from Marvell only supports serialised modes as its
line-facing interfaces. Convert that driver to the generic phylib SFP
handling.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
 drivers/net/phy/marvell-88x2222.c | 98 +++++++++++++------------------
 1 file changed, 41 insertions(+), 57 deletions(-)

diff --git a/drivers/net/phy/marvell-88x2222.c b/drivers/net/phy/marvell-88x2222.c
index fad2f54c1eac..7a7fbdc221af 100644
--- a/drivers/net/phy/marvell-88x2222.c
+++ b/drivers/net/phy/marvell-88x2222.c
@@ -13,7 +13,7 @@
 #include <linux/mdio.h>
 #include <linux/marvell_phy.h>
 #include <linux/of.h>
-#include <linux/sfp.h>
+#include <linux/phy_port.h>
 #include <linux/netdevice.h>
 
 /* Port PCS Configuration */
@@ -473,90 +473,73 @@ static int mv2222_config_init(struct phy_device *phydev)
 	return 0;
 }
 
-static int mv2222_sfp_insert(void *upstream, const struct sfp_eeprom_id *id)
+static int mv2222_configure_serdes(struct phy_port *port, bool enable,
+				   phy_interface_t interface)
 {
-	DECLARE_PHY_INTERFACE_MASK(interfaces);
-	struct phy_device *phydev = upstream;
-	phy_interface_t sfp_interface;
+	struct phy_device *phydev = port_phydev(port);
 	struct mv2222_data *priv;
-	struct device *dev;
-	int ret;
-
-	__ETHTOOL_DECLARE_LINK_MODE_MASK(sfp_supported) = { 0, };
+	int ret = 0;
 
 	priv = phydev->priv;
-	dev = &phydev->mdio.dev;
-
-	sfp_parse_support(phydev->sfp_bus, id, sfp_supported, interfaces);
-	phydev->port = sfp_parse_port(phydev->sfp_bus, id, sfp_supported);
-	sfp_interface = sfp_select_interface(phydev->sfp_bus, sfp_supported);
-
-	dev_info(dev, "%s SFP module inserted\n", phy_modes(sfp_interface));
+	priv->line_interface = interface;
 
-	if (sfp_interface != PHY_INTERFACE_MODE_10GBASER &&
-	    sfp_interface != PHY_INTERFACE_MODE_1000BASEX &&
-	    sfp_interface != PHY_INTERFACE_MODE_SGMII) {
-		dev_err(dev, "Incompatible SFP module inserted\n");
+	if (enable) {
+		linkmode_and(priv->supported, phydev->supported, port->supported);
 
-		return -EINVAL;
-	}
-
-	priv->line_interface = sfp_interface;
-	linkmode_and(priv->supported, phydev->supported, sfp_supported);
+		ret = mv2222_config_line(phydev);
+		if (ret < 0)
+			return ret;
 
-	ret = mv2222_config_line(phydev);
-	if (ret < 0)
-		return ret;
+		if (mutex_trylock(&phydev->lock)) {
+			ret = mv2222_config_aneg(phydev);
+			mutex_unlock(&phydev->lock);
+		}
 
-	if (mutex_trylock(&phydev->lock)) {
-		ret = mv2222_config_aneg(phydev);
-		mutex_unlock(&phydev->lock);
+	} else {
+		linkmode_zero(priv->supported);
 	}
 
 	return ret;
 }
 
-static void mv2222_sfp_remove(void *upstream)
+static void mv2222_port_link_up(struct phy_port *port)
 {
-	struct phy_device *phydev = upstream;
-	struct mv2222_data *priv;
-
-	priv = phydev->priv;
-
-	priv->line_interface = PHY_INTERFACE_MODE_NA;
-	linkmode_zero(priv->supported);
-	phydev->port = PORT_NONE;
-}
-
-static void mv2222_sfp_link_up(void *upstream)
-{
-	struct phy_device *phydev = upstream;
+	struct phy_device *phydev = port_phydev(port);
 	struct mv2222_data *priv;
 
 	priv = phydev->priv;
 	priv->sfp_link = true;
 }
 
-static void mv2222_sfp_link_down(void *upstream)
+static void mv2222_port_link_down(struct phy_port *port)
 {
-	struct phy_device *phydev = upstream;
+	struct phy_device *phydev = port_phydev(port);
 	struct mv2222_data *priv;
 
 	priv = phydev->priv;
 	priv->sfp_link = false;
 }
 
-static const struct sfp_upstream_ops sfp_phy_ops = {
-	.module_insert = mv2222_sfp_insert,
-	.module_remove = mv2222_sfp_remove,
-	.link_up = mv2222_sfp_link_up,
-	.link_down = mv2222_sfp_link_down,
-	.attach = phy_sfp_attach,
-	.detach = phy_sfp_detach,
-	.connect_phy = phy_sfp_connect_phy,
-	.disconnect_phy = phy_sfp_disconnect_phy,
+static const struct phy_port_ops mv2222_port_ops = {
+	.link_up = mv2222_port_link_up,
+	.link_down = mv2222_port_link_down,
+	.configure_mii = mv2222_configure_serdes,
 };
 
+static int mv2222_attach_port(struct phy_device *phydev, struct phy_port *port)
+{
+	if (!port->is_mii)
+		return 0;
+
+	port->ops = &mv2222_port_ops;
+
+	__set_bit(PHY_INTERFACE_MODE_10GBASER, port->interfaces);
+	__set_bit(PHY_INTERFACE_MODE_1000BASEX, port->interfaces);
+	__set_bit(PHY_INTERFACE_MODE_SGMII, port->interfaces);
+
+	return 0;
+}
+
 static int mv2222_probe(struct phy_device *phydev)
 {
 	struct device *dev = &phydev->mdio.dev;
@@ -592,7 +575,7 @@ static int mv2222_probe(struct phy_device *phydev)
 	priv->line_interface = PHY_INTERFACE_MODE_NA;
 	phydev->priv = priv;
 
-	return phy_sfp_probe(phydev, &sfp_phy_ops);
+	return 0;
 }
 
 static struct phy_driver mv2222_drivers[] = {
@@ -609,6 +592,7 @@ static struct phy_driver mv2222_drivers[] = {
 		.suspend = mv2222_suspend,
 		.resume = mv2222_resume,
 		.read_status = mv2222_read_status,
+		.attach_port = mv2222_attach_port,
 	},
 };
 module_phy_driver(mv2222_drivers);
-- 
2.49.0

[PATCH net-next v7 09/15] net: phy: marvell: Support SFP through phy_port interface

[Maxime Chevallier]

Convert the Marvell driver (especially the 88e1512 driver) to use the
phy_port interface to handle SFPs. This means registering a
.attach_port() handler to detect when a serdes line interface is used
(most likely, and SFP module).

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
 drivers/net/phy/marvell.c | 100 +++++++++++++++-----------------------
 1 file changed, 39 insertions(+), 61 deletions(-)

diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c
index 623292948fa7..4f5fe5189fb1 100644
--- a/drivers/net/phy/marvell.c
+++ b/drivers/net/phy/marvell.c
@@ -29,10 +29,10 @@
 #include <linux/ethtool.h>
 #include <linux/ethtool_netlink.h>
 #include <linux/phy.h>
+#include <linux/phy_port.h>
 #include <linux/marvell_phy.h>
 #include <linux/bitfield.h>
 #include <linux/of.h>
-#include <linux/sfp.h>
 
 #include <linux/io.h>
 #include <asm/irq.h>
@@ -3561,42 +3561,38 @@ static int marvell_probe(struct phy_device *phydev)
 	return marvell_hwmon_probe(phydev);
 }
 
-static int m88e1510_sfp_insert(void *upstream, const struct sfp_eeprom_id *id)
+static int mv88e1510_port_configure_serdes(struct phy_port *port, bool enable,
+					   phy_interface_t interface)
 {
-	DECLARE_PHY_INTERFACE_MASK(interfaces);
-	struct phy_device *phydev = upstream;
-	phy_interface_t interface;
+	struct phy_device *phydev = port_phydev(port);
 	struct device *dev;
 	int oldpage;
 	int ret = 0;
 	u16 mode;
 
-	__ETHTOOL_DECLARE_LINK_MODE_MASK(supported) = { 0, };
-
 	dev = &phydev->mdio.dev;
 
-	sfp_parse_support(phydev->sfp_bus, id, supported, interfaces);
-	interface = sfp_select_interface(phydev->sfp_bus, supported);
-
-	dev_info(dev, "%s SFP module inserted\n", phy_modes(interface));
+	if (enable) {
+		switch (interface) {
+		case PHY_INTERFACE_MODE_1000BASEX:
+			mode = MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_1000X;
 
-	switch (interface) {
-	case PHY_INTERFACE_MODE_1000BASEX:
-		mode = MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_1000X;
+			break;
+		case PHY_INTERFACE_MODE_100BASEX:
+			mode = MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_100FX;
 
-		break;
-	case PHY_INTERFACE_MODE_100BASEX:
-		mode = MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_100FX;
-
-		break;
-	case PHY_INTERFACE_MODE_SGMII:
-		mode = MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_SGMII;
+			break;
+		case PHY_INTERFACE_MODE_SGMII:
+			mode = MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII_SGMII;
 
-		break;
-	default:
-		dev_err(dev, "Incompatible SFP module inserted\n");
+			break;
+		default:
+			dev_err(dev, "Incompatible SFP module inserted\n");
 
-		return -EINVAL;
+			return -EINVAL;
+		}
+	} else {
+		mode = MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII;
 	}
 
 	oldpage = phy_select_page(phydev, MII_MARVELL_MODE_PAGE);
@@ -3613,49 +3609,30 @@ static int m88e1510_sfp_insert(void *upstream, const struct sfp_eeprom_id *id)
 
 error:
 	return phy_restore_page(phydev, oldpage, ret);
-}
-
-static void m88e1510_sfp_remove(void *upstream)
-{
-	struct phy_device *phydev = upstream;
-	int oldpage;
-	int ret = 0;
-
-	oldpage = phy_select_page(phydev, MII_MARVELL_MODE_PAGE);
-	if (oldpage < 0)
-		goto error;
 
-	ret = __phy_modify(phydev, MII_88E1510_GEN_CTRL_REG_1,
-			   MII_88E1510_GEN_CTRL_REG_1_MODE_MASK,
-			   MII_88E1510_GEN_CTRL_REG_1_MODE_RGMII);
-	if (ret < 0)
-		goto error;
-
-	ret = __phy_set_bits(phydev, MII_88E1510_GEN_CTRL_REG_1,
-			     MII_88E1510_GEN_CTRL_REG_1_RESET);
-
-error:
-	phy_restore_page(phydev, oldpage, ret);
+	return 0;
 }
 
-static const struct sfp_upstream_ops m88e1510_sfp_ops = {
-	.module_insert = m88e1510_sfp_insert,
-	.module_remove = m88e1510_sfp_remove,
-	.attach = phy_sfp_attach,
-	.detach = phy_sfp_detach,
-	.connect_phy = phy_sfp_connect_phy,
-	.disconnect_phy = phy_sfp_disconnect_phy,
+static const struct phy_port_ops mv88e1510_serdes_port_ops = {
+	.configure_mii = mv88e1510_port_configure_serdes,
 };
 
-static int m88e1510_probe(struct phy_device *phydev)
+static int m88e1510_attach_port(struct phy_device *phy_device,
+				struct phy_port *port)
 {
-	int err;
+	/* For classic Copper operation, we don't have any port-specific
+	 * control to do.
+	 */
+	if (!port->is_mii)
+		return 0;
 
-	err = marvell_probe(phydev);
-	if (err)
-		return err;
+	port->ops = &mv88e1510_serdes_port_ops;
+
+	__set_bit(PHY_INTERFACE_MODE_SGMII, port->interfaces);
+	__set_bit(PHY_INTERFACE_MODE_1000BASEX, port->interfaces);
+	__set_bit(PHY_INTERFACE_MODE_100BASEX, port->interfaces);
 
-	return phy_sfp_probe(phydev, &m88e1510_sfp_ops);
+	return 0;
 }
 
 static struct phy_driver marvell_drivers[] = {
@@ -3915,7 +3892,7 @@ static struct phy_driver marvell_drivers[] = {
 		.driver_data = DEF_MARVELL_HWMON_OPS(m88e1510_hwmon_ops),
 		.features = PHY_GBIT_FIBRE_FEATURES,
 		.flags = PHY_POLL_CABLE_TEST,
-		.probe = m88e1510_probe,
+		.probe = marvell_probe,
 		.config_init = m88e1510_config_init,
 		.config_aneg = m88e1510_config_aneg,
 		.read_status = marvell_read_status,
@@ -3941,6 +3918,7 @@ static struct phy_driver marvell_drivers[] = {
 		.led_hw_is_supported = m88e1318_led_hw_is_supported,
 		.led_hw_control_set = m88e1318_led_hw_control_set,
 		.led_hw_control_get = m88e1318_led_hw_control_get,
+		.attach_port = m88e1510_attach_port,
 	},
 	{
 		.phy_id = MARVELL_PHY_ID_88E1540,
-- 
2.49.0

[PATCH net-next v7 10/15] net: phy: marvell10g: Support SFP through phy_port

[Maxime Chevallier]

Convert the Marvell10G driver to use the generic SFP handling, through a
dedicated .attach_port() handler to populate the port's supported
interfaces.

As the 88x3310 supports multiple MDI, the .attach_port() logic handles
both SFP attach with 10GBaseR support, and support for the "regular"
port that usually is a BaseT port.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
 drivers/net/phy/marvell10g.c | 47 +++++++++++++++++++-----------------
 drivers/net/phy/phy_port.c   | 20 +++++++++++++++
 include/linux/phy_port.h     |  1 +
 3 files changed, 46 insertions(+), 22 deletions(-)

diff --git a/drivers/net/phy/marvell10g.c b/drivers/net/phy/marvell10g.c
index 13e81dff42c1..7cb638804a3f 100644
--- a/drivers/net/phy/marvell10g.c
+++ b/drivers/net/phy/marvell10g.c
@@ -28,7 +28,7 @@
 #include <linux/hwmon.h>
 #include <linux/marvell_phy.h>
 #include <linux/phy.h>
-#include <linux/sfp.h>
+#include <linux/phy_port.h>
 #include <linux/netdevice.h>
 
 #define MV_PHY_ALASKA_NBT_QUIRK_MASK	0xfffffffe
@@ -463,36 +463,31 @@ static int mv3310_set_edpd(struct phy_device *phydev, u16 edpd)
 	return err;
 }
 
-static int mv3310_sfp_insert(void *upstream, const struct sfp_eeprom_id *id)
+static int mv3310_attach_port(struct phy_device *phydev, struct phy_port *port)
 {
-	struct phy_device *phydev = upstream;
-	__ETHTOOL_DECLARE_LINK_MODE_MASK(support) = { 0, };
-	DECLARE_PHY_INTERFACE_MASK(interfaces);
-	phy_interface_t iface;
-
-	sfp_parse_support(phydev->sfp_bus, id, support, interfaces);
-	iface = sfp_select_interface(phydev->sfp_bus, support);
-
-	if (iface != PHY_INTERFACE_MODE_10GBASER) {
-		dev_err(&phydev->mdio.dev, "incompatible SFP module inserted\n");
-		return -EINVAL;
+	if (port->is_mii) {
+		__set_bit(PHY_INTERFACE_MODE_10GBASER, port->interfaces);
+	} else if (port->not_described) {
+		/* This PHY can do combo-ports, i.e. 2 MDI outputs, usually one
+		 * of them going to an SFP and the other one to a RJ45
+		 * connector. If we don't have any representation for the port
+		 * in DT, and we are dealing with a non-SFP port, then we
+		 * mask the port's capabilities to report BaseT-only modes
+		 */
+		port->mediums = BIT(ETHTOOL_LINK_MEDIUM_BASET);
+
+		phy_port_filter_supported(port);
 	}
+
 	return 0;
 }
 
-static const struct sfp_upstream_ops mv3310_sfp_ops = {
-	.attach = phy_sfp_attach,
-	.detach = phy_sfp_detach,
-	.connect_phy = phy_sfp_connect_phy,
-	.disconnect_phy = phy_sfp_disconnect_phy,
-	.module_insert = mv3310_sfp_insert,
-};
-
 static int mv3310_probe(struct phy_device *phydev)
 {
 	const struct mv3310_chip *chip = to_mv3310_chip(phydev);
 	struct mv3310_priv *priv;
 	u32 mmd_mask = MDIO_DEVS_PMAPMD | MDIO_DEVS_AN;
+	DECLARE_PHY_INTERFACE_MASK(interfaces);
 	int ret;
 
 	if (!phydev->is_c45 ||
@@ -543,9 +538,13 @@ static int mv3310_probe(struct phy_device *phydev)
 	if (ret)
 		return ret;
 
+	__set_bit(PHY_INTERFACE_MODE_10GBASER, interfaces);
+
 	chip->init_supported_interfaces(priv->supported_interfaces);
 
-	return phy_sfp_probe(phydev, &mv3310_sfp_ops);
+	phydev->max_n_ports = 2;
+
+	return 0;
 }
 
 static void mv3310_remove(struct phy_device *phydev)
@@ -1406,6 +1405,7 @@ static struct phy_driver mv3310_drivers[] = {
 		.set_loopback	= genphy_c45_loopback,
 		.get_wol	= mv3110_get_wol,
 		.set_wol	= mv3110_set_wol,
+		.attach_port	= mv3310_attach_port,
 	},
 	{
 		.phy_id		= MARVELL_PHY_ID_88X3310,
@@ -1425,6 +1425,7 @@ static struct phy_driver mv3310_drivers[] = {
 		.set_tunable	= mv3310_set_tunable,
 		.remove		= mv3310_remove,
 		.set_loopback	= genphy_c45_loopback,
+		.attach_port	= mv3310_attach_port,
 	},
 	{
 		.phy_id		= MARVELL_PHY_ID_88E2110,
@@ -1445,6 +1446,7 @@ static struct phy_driver mv3310_drivers[] = {
 		.set_loopback	= genphy_c45_loopback,
 		.get_wol	= mv3110_get_wol,
 		.set_wol	= mv3110_set_wol,
+		.attach_port	= mv3310_attach_port,
 	},
 	{
 		.phy_id		= MARVELL_PHY_ID_88E2110,
@@ -1463,6 +1465,7 @@ static struct phy_driver mv3310_drivers[] = {
 		.set_tunable	= mv3310_set_tunable,
 		.remove		= mv3310_remove,
 		.set_loopback	= genphy_c45_loopback,
+		.attach_port	= mv3310_attach_port,
 	},
 };
 
diff --git a/drivers/net/phy/phy_port.c b/drivers/net/phy/phy_port.c
index 2c5ae947d759..c27dacda259a 100644
--- a/drivers/net/phy/phy_port.c
+++ b/drivers/net/phy/phy_port.c
@@ -134,6 +134,26 @@ void phy_port_update_supported(struct phy_port *port)
 }
 EXPORT_SYMBOL_GPL(phy_port_update_supported);
 
+/**
+ * phy_port_filter_supported() - Make sure that port->supported match port->mediums
+ * @port: The port to filter
+ *
+ * After updating a port's mediums to a more restricted subset, this helper will
+ * make sure that port->supported only contains linkmodes that are compatible
+ * with port->mediums.
+ */
+void phy_port_filter_supported(struct phy_port *port)
+{
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(supported) = { 0 };
+	int i;
+
+	for_each_set_bit(i, &port->mediums, __ETHTOOL_LINK_MEDIUM_LAST)
+		phy_caps_medium_get_supported(supported, i, port->lanes);
+
+	linkmode_and(port->supported, port->supported, supported);
+}
+EXPORT_SYMBOL_GPL(phy_port_filter_supported);
+
 /**
  * phy_port_get_type() - get the PORT_* attribut for that port.
  * @port: The port we want the information from
diff --git a/include/linux/phy_port.h b/include/linux/phy_port.h
index f47ac5f5ef9e..ce735d81bcd0 100644
--- a/include/linux/phy_port.h
+++ b/include/linux/phy_port.h
@@ -90,6 +90,7 @@ static inline bool phy_port_is_fiber(struct phy_port *port)
 }
 
 void phy_port_update_supported(struct phy_port *port);
+void phy_port_filter_supported(struct phy_port *port);
 
 int phy_port_get_type(struct phy_port *port);
 
-- 
2.49.0

[PATCH net-next v7 11/15] net: phy: at803x: Support SFP through phy_port interface

[Maxime Chevallier]

Convert the at803x driver to use the generic phylib SFP handling, via a
dedicated .attach_port() callback, populating the supported interfaces.

As these devices are limited to 1000BaseX, a workaround is used to also
support, in a very limited way, copper modules. This is done by
supporting SGMII but limiting it to 1G full duplex (in which case it's
somwhat compatible with 1000BaseX).

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
 drivers/net/phy/qcom/at803x.c | 64 ++++++++++-------------------------
 1 file changed, 17 insertions(+), 47 deletions(-)

diff --git a/drivers/net/phy/qcom/at803x.c b/drivers/net/phy/qcom/at803x.c
index 43e604171828..fcc72542c137 100644
--- a/drivers/net/phy/qcom/at803x.c
+++ b/drivers/net/phy/qcom/at803x.c
@@ -20,7 +20,7 @@
 #include <linux/of.h>
 #include <linux/phylink.h>
 #include <linux/reset.h>
-#include <linux/sfp.h>
+#include <linux/phy_port.h>
 #include <dt-bindings/net/qca-ar803x.h>
 
 #include "qcom.h"
@@ -772,58 +772,28 @@ static int at8031_register_regulators(struct phy_device *phydev)
 	return 0;
 }
 
-static int at8031_sfp_insert(void *upstream, const struct sfp_eeprom_id *id)
+static int at8031_attach_port(struct phy_device *phydev, struct phy_port *port)
 {
-	struct phy_device *phydev = upstream;
-	__ETHTOOL_DECLARE_LINK_MODE_MASK(phy_support);
-	__ETHTOOL_DECLARE_LINK_MODE_MASK(sfp_support);
-	DECLARE_PHY_INTERFACE_MASK(interfaces);
-	phy_interface_t iface;
-
-	linkmode_zero(phy_support);
-	phylink_set(phy_support, 1000baseX_Full);
-	phylink_set(phy_support, 1000baseT_Full);
-	phylink_set(phy_support, Autoneg);
-	phylink_set(phy_support, Pause);
-	phylink_set(phy_support, Asym_Pause);
-
-	linkmode_zero(sfp_support);
-	sfp_parse_support(phydev->sfp_bus, id, sfp_support, interfaces);
-	/* Some modules support 10G modes as well as others we support.
-	 * Mask out non-supported modes so the correct interface is picked.
-	 */
-	linkmode_and(sfp_support, phy_support, sfp_support);
-
-	if (linkmode_empty(sfp_support)) {
-		dev_err(&phydev->mdio.dev, "incompatible SFP module inserted\n");
-		return -EINVAL;
-	}
+	if (!port->is_mii)
+		return 0;
 
-	iface = sfp_select_interface(phydev->sfp_bus, sfp_support);
+	linkmode_zero(port->supported);
+	phylink_set(port->supported, 1000baseX_Full);
+	phylink_set(port->supported, 1000baseT_Full);
+	phylink_set(port->supported, Autoneg);
+	phylink_set(port->supported, Pause);
+	phylink_set(port->supported, Asym_Pause);
 
-	/* Only 1000Base-X is supported by AR8031/8033 as the downstream SerDes
-	 * interface for use with SFP modules.
-	 * However, some copper modules detected as having a preferred SGMII
-	 * interface do default to and function in 1000Base-X mode, so just
-	 * print a warning and allow such modules, as they may have some chance
-	 * of working.
+	/* This device doesn't really support SGMII. However, do our best
+	 * to be compatible with copper modules (that usually require SGMII),
+	 * in a degraded mode as we only allow 1000BaseT Full
 	 */
-	if (iface == PHY_INTERFACE_MODE_SGMII)
-		dev_warn(&phydev->mdio.dev, "module may not function if 1000Base-X not supported\n");
-	else if (iface != PHY_INTERFACE_MODE_1000BASEX)
-		return -EINVAL;
+	__set_bit(PHY_INTERFACE_MODE_SGMII, port->interfaces);
+	__set_bit(PHY_INTERFACE_MODE_1000BASEX, port->interfaces);
 
 	return 0;
 }
 
-static const struct sfp_upstream_ops at8031_sfp_ops = {
-	.attach = phy_sfp_attach,
-	.detach = phy_sfp_detach,
-	.module_insert = at8031_sfp_insert,
-	.connect_phy = phy_sfp_connect_phy,
-	.disconnect_phy = phy_sfp_disconnect_phy,
-};
-
 static int at8031_parse_dt(struct phy_device *phydev)
 {
 	struct device_node *node = phydev->mdio.dev.of_node;
@@ -844,8 +814,7 @@ static int at8031_parse_dt(struct phy_device *phydev)
 		return ret;
 	}
 
-	/* Only AR8031/8033 support 1000Base-X for SFP modules */
-	return phy_sfp_probe(phydev, &at8031_sfp_ops);
+	return 0;
 }
 
 static int at8031_probe(struct phy_device *phydev)
@@ -1200,6 +1169,7 @@ static struct phy_driver at803x_driver[] = {
 	.set_tunable		= at803x_set_tunable,
 	.cable_test_start	= at8031_cable_test_start,
 	.cable_test_get_status	= at8031_cable_test_get_status,
+	.attach_port		= at8031_attach_port,
 }, {
 	/* Qualcomm Atheros AR8032 */
 	PHY_ID_MATCH_EXACT(ATH8032_PHY_ID),
-- 
2.49.0

[PATCH net-next v7 12/15] net: phy: qca807x: Support SFP through phy_port interface

[Maxime Chevallier]

QCA8072/8075 may be used as combo-port PHYs, with Serdes (100/1000BaseX)
 and Copper interfaces. The PHY has the ability to read the configuration
it's in.  If the configuration indicates the PHY is in combo mode, allow
registering up to 2 ports.

Register a dedicated set of port ops to handle the serdes port, and rely
on generic phylib SFP support for the SFP handling.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
 drivers/net/phy/qcom/qca807x.c | 75 +++++++++++++++-------------------
 1 file changed, 32 insertions(+), 43 deletions(-)

diff --git a/drivers/net/phy/qcom/qca807x.c b/drivers/net/phy/qcom/qca807x.c
index 6d10ef7e9a8a..ce92836b2472 100644
--- a/drivers/net/phy/qcom/qca807x.c
+++ b/drivers/net/phy/qcom/qca807x.c
@@ -13,7 +13,7 @@
 #include <linux/phy.h>
 #include <linux/bitfield.h>
 #include <linux/gpio/driver.h>
-#include <linux/sfp.h>
+#include <linux/phy_port.h>
 
 #include "../phylib.h"
 #include "qcom.h"
@@ -642,67 +642,55 @@ static int qca807x_phy_package_config_init_once(struct phy_device *phydev)
 	return ret;
 }
 
-static int qca807x_sfp_insert(void *upstream, const struct sfp_eeprom_id *id)
+static int qca807x_configure_serdes(struct phy_port *port, bool enable,
+				    phy_interface_t interface)
 {
-	struct phy_device *phydev = upstream;
-	__ETHTOOL_DECLARE_LINK_MODE_MASK(support) = { 0, };
-	phy_interface_t iface;
+	struct phy_device *phydev = port_phydev(port);
 	int ret;
-	DECLARE_PHY_INTERFACE_MASK(interfaces);
 
-	sfp_parse_support(phydev->sfp_bus, id, support, interfaces);
-	iface = sfp_select_interface(phydev->sfp_bus, support);
+	if (!phydev)
+		return -ENODEV;
 
-	dev_info(&phydev->mdio.dev, "%s SFP module inserted\n", phy_modes(iface));
-
-	switch (iface) {
-	case PHY_INTERFACE_MODE_1000BASEX:
-	case PHY_INTERFACE_MODE_100BASEX:
+	if (enable) {
 		/* Set PHY mode to PSGMII combo (1/4 copper + combo ports) mode */
 		ret = phy_modify(phydev,
 				 QCA807X_CHIP_CONFIGURATION,
 				 QCA807X_CHIP_CONFIGURATION_MODE_CFG_MASK,
 				 QCA807X_CHIP_CONFIGURATION_MODE_PSGMII_FIBER);
+		if (ret)
+			return ret;
 		/* Enable fiber mode autodection (1000Base-X or 100Base-FX) */
 		ret = phy_set_bits_mmd(phydev,
 				       MDIO_MMD_AN,
 				       QCA807X_MMD7_FIBER_MODE_AUTO_DETECTION,
 				       QCA807X_MMD7_FIBER_MODE_AUTO_DETECTION_EN);
-		/* Select fiber page */
-		ret = phy_clear_bits(phydev,
-				     QCA807X_CHIP_CONFIGURATION,
-				     QCA807X_BT_BX_REG_SEL);
-
-		phydev->port = PORT_FIBRE;
-		break;
-	default:
-		dev_err(&phydev->mdio.dev, "Incompatible SFP module inserted\n");
-		return -EINVAL;
+		if (ret)
+			return ret;
 	}
 
-	return ret;
+	phydev->port = enable ? PORT_FIBRE : PORT_TP;
+
+	return phy_modify(phydev, QCA807X_CHIP_CONFIGURATION,
+			  QCA807X_BT_BX_REG_SEL,
+			  enable ? 0 : QCA807X_BT_BX_REG_SEL);
 }
 
-static void qca807x_sfp_remove(void *upstream)
+static const struct phy_port_ops qca807x_serdes_port_ops = {
+	.configure_mii = qca807x_configure_serdes,
+};
+
+static int qca807x_attach_port(struct phy_device *phydev, struct phy_port *port)
 {
-	struct phy_device *phydev = upstream;
+	if (!port->is_mii)
+		return 0;
 
-	/* Select copper page */
-	phy_set_bits(phydev,
-		     QCA807X_CHIP_CONFIGURATION,
-		     QCA807X_BT_BX_REG_SEL);
+	__set_bit(PHY_INTERFACE_MODE_1000BASEX, port->interfaces);
+	__set_bit(PHY_INTERFACE_MODE_100BASEX, port->interfaces);
 
-	phydev->port = PORT_TP;
-}
+	port->ops = &qca807x_serdes_port_ops;
 
-static const struct sfp_upstream_ops qca807x_sfp_ops = {
-	.attach = phy_sfp_attach,
-	.detach = phy_sfp_detach,
-	.module_insert = qca807x_sfp_insert,
-	.module_remove = qca807x_sfp_remove,
-	.connect_phy = phy_sfp_connect_phy,
-	.disconnect_phy = phy_sfp_disconnect_phy,
-};
+	return 0;
+}
 
 static int qca807x_probe(struct phy_device *phydev)
 {
@@ -744,9 +732,8 @@ static int qca807x_probe(struct phy_device *phydev)
 
 	/* Attach SFP bus on combo port*/
 	if (phy_read(phydev, QCA807X_CHIP_CONFIGURATION)) {
-		ret = phy_sfp_probe(phydev, &qca807x_sfp_ops);
-		if (ret)
-			return ret;
+		phydev->max_n_ports = 2;
+
 		linkmode_set_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, phydev->supported);
 		linkmode_set_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, phydev->advertising);
 	}
@@ -800,6 +787,7 @@ static struct phy_driver qca807x_drivers[] = {
 		.suspend	= genphy_suspend,
 		.cable_test_start	= qca807x_cable_test_start,
 		.cable_test_get_status	= qca808x_cable_test_get_status,
+		.attach_port	= qca807x_attach_port,
 	},
 	{
 		PHY_ID_MATCH_EXACT(PHY_ID_QCA8075),
@@ -823,6 +811,7 @@ static struct phy_driver qca807x_drivers[] = {
 		.led_hw_is_supported = qca807x_led_hw_is_supported,
 		.led_hw_control_set = qca807x_led_hw_control_set,
 		.led_hw_control_get = qca807x_led_hw_control_get,
+		.attach_port	= qca807x_attach_port,
 	},
 };
 module_phy_driver(qca807x_drivers);
-- 
2.49.0

[PATCH net-next v7 13/15] net: phy: Only rely on phy_port for PHY-driven SFP

[Maxime Chevallier]

Now that all PHY drivers that support downstream SFP have been converted
to phy_port serdes handling, we can make the generic PHY SFP handling
mandatory, thus making all phylib sfp helpers static.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
 drivers/net/phy/phy_device.c | 28 +++++++++-------------------
 include/linux/phy.h          |  6 ------
 2 files changed, 9 insertions(+), 25 deletions(-)

diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index 5a037e78a761..f7d2cc95f986 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -1521,7 +1521,7 @@ static DEVICE_ATTR_RO(phy_standalone);
  *
  * Return: 0 on success, otherwise a negative error code.
  */
-int phy_sfp_connect_phy(void *upstream, struct phy_device *phy)
+static int phy_sfp_connect_phy(void *upstream, struct phy_device *phy)
 {
 	struct phy_device *phydev = upstream;
 	struct net_device *dev = phydev->attached_dev;
@@ -1531,7 +1531,6 @@ int phy_sfp_connect_phy(void *upstream, struct phy_device *phy)
 
 	return 0;
 }
-EXPORT_SYMBOL(phy_sfp_connect_phy);
 
 /**
  * phy_sfp_disconnect_phy - Disconnect the SFP module's PHY from the upstream PHY
@@ -1543,7 +1542,7 @@ EXPORT_SYMBOL(phy_sfp_connect_phy);
  * will be destroyed, re-inserting the same module will add a new phy with a
  * new index.
  */
-void phy_sfp_disconnect_phy(void *upstream, struct phy_device *phy)
+static void phy_sfp_disconnect_phy(void *upstream, struct phy_device *phy)
 {
 	struct phy_device *phydev = upstream;
 	struct net_device *dev = phydev->attached_dev;
@@ -1551,7 +1550,6 @@ void phy_sfp_disconnect_phy(void *upstream, struct phy_device *phy)
 	if (dev)
 		phy_link_topo_del_phy(dev, phy);
 }
-EXPORT_SYMBOL(phy_sfp_disconnect_phy);
 
 /**
  * phy_sfp_attach - attach the SFP bus to the PHY upstream network device
@@ -1560,7 +1558,7 @@ EXPORT_SYMBOL(phy_sfp_disconnect_phy);
  *
  * This is used to fill in the sfp_upstream_ops .attach member.
  */
-void phy_sfp_attach(void *upstream, struct sfp_bus *bus)
+static void phy_sfp_attach(void *upstream, struct sfp_bus *bus)
 {
 	struct phy_device *phydev = upstream;
 
@@ -1568,7 +1566,6 @@ void phy_sfp_attach(void *upstream, struct sfp_bus *bus)
 		phydev->attached_dev->sfp_bus = bus;
 	phydev->sfp_bus_attached = true;
 }
-EXPORT_SYMBOL(phy_sfp_attach);
 
 /**
  * phy_sfp_detach - detach the SFP bus from the PHY upstream network device
@@ -1577,7 +1574,7 @@ EXPORT_SYMBOL(phy_sfp_attach);
  *
  * This is used to fill in the sfp_upstream_ops .detach member.
  */
-void phy_sfp_detach(void *upstream, struct sfp_bus *bus)
+static void phy_sfp_detach(void *upstream, struct sfp_bus *bus)
 {
 	struct phy_device *phydev = upstream;
 
@@ -1585,7 +1582,6 @@ void phy_sfp_detach(void *upstream, struct sfp_bus *bus)
 		phydev->attached_dev->sfp_bus = NULL;
 	phydev->sfp_bus_attached = false;
 }
-EXPORT_SYMBOL(phy_sfp_detach);
 
 static int phy_sfp_module_insert(void *upstream, const struct sfp_eeprom_id *id)
 {
@@ -1731,10 +1727,8 @@ static int phy_setup_sfp_port(struct phy_device *phydev)
 /**
  * phy_sfp_probe - probe for a SFP cage attached to this PHY device
  * @phydev: Pointer to phy_device
- * @ops: SFP's upstream operations
  */
-int phy_sfp_probe(struct phy_device *phydev,
-		  const struct sfp_upstream_ops *ops)
+static int phy_sfp_probe(struct phy_device *phydev)
 {
 	struct sfp_bus *bus;
 	int ret = 0;
@@ -1746,7 +1740,7 @@ int phy_sfp_probe(struct phy_device *phydev,
 
 		phydev->sfp_bus = bus;
 
-		ret = sfp_bus_add_upstream(bus, phydev, ops);
+		ret = sfp_bus_add_upstream(bus, phydev, &sfp_phydev_ops);
 		sfp_bus_put(bus);
 	}
 
@@ -1755,7 +1749,6 @@ int phy_sfp_probe(struct phy_device *phydev,
 
 	return ret;
 }
-EXPORT_SYMBOL(phy_sfp_probe);
 
 static bool phy_drv_supports_irq(const struct phy_driver *phydrv)
 {
@@ -3555,12 +3548,9 @@ static int phy_setup_ports(struct phy_device *phydev)
 	if (ret)
 		return ret;
 
-	/* Use generic SFP probing only if the driver didn't do so already */
-	if (!phydev->sfp_bus) {
-		ret = phy_sfp_probe(phydev, &sfp_phydev_ops);
-		if (ret)
-			goto out;
-	}
+	ret = phy_sfp_probe(phydev);
+	if (ret)
+		goto out;
 
 	if (phydev->n_ports < phydev->max_n_ports) {
 		ret = phy_default_setup_single_port(phydev);
diff --git a/include/linux/phy.h b/include/linux/phy.h
index 03548cc55aa8..dfa6b7e539ee 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -1821,12 +1821,6 @@ int phy_suspend(struct phy_device *phydev);
 int phy_resume(struct phy_device *phydev);
 int __phy_resume(struct phy_device *phydev);
 int phy_loopback(struct phy_device *phydev, bool enable, int speed);
-int phy_sfp_connect_phy(void *upstream, struct phy_device *phy);
-void phy_sfp_disconnect_phy(void *upstream, struct phy_device *phy);
-void phy_sfp_attach(void *upstream, struct sfp_bus *bus);
-void phy_sfp_detach(void *upstream, struct sfp_bus *bus);
-int phy_sfp_probe(struct phy_device *phydev,
-	          const struct sfp_upstream_ops *ops);
 struct phy_device *phy_attach(struct net_device *dev, const char *bus_id,
 			      phy_interface_t interface);
 struct phy_device *phy_find_first(struct mii_bus *bus);
-- 
2.49.0

[PATCH net-next v7 14/15] net: phy: dp83822: Add SFP support through the phy_port interface

[Maxime Chevallier]

The DP83822 can support 100BaseFX. This mode was only accessible through
custom DT properties, but there also exist SFP modules that support
these modes. As this only requires setting the relevant supported
interface in the driver, expose the port capability with the new
phy_port API, allowing SFP support.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
 drivers/net/phy/dp83822.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/drivers/net/phy/dp83822.c b/drivers/net/phy/dp83822.c
index 2657be2e9034..aa2c0085a900 100644
--- a/drivers/net/phy/dp83822.c
+++ b/drivers/net/phy/dp83822.c
@@ -979,6 +979,13 @@ static int dp83822_attach_port(struct phy_device *phydev, struct phy_port *port)
 		}
 	}
 
+	/* If attached from SFP, is_mii is set, but not the mediums. */
+	if (port->is_mii)
+		dp83822->fx_enabled = true;
+
+	if (dp83822->fx_enabled)
+		__set_bit(PHY_INTERFACE_MODE_100BASEX, port->interfaces);
+
 	return 0;
 }
 
-- 
2.49.0

[PATCH net-next v7 15/15] Documentation: networking: Document the phy_port infrastructure

[Maxime Chevallier]

This documentation aims at describing the main goal of the phy_port
infrastructure.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
 Documentation/networking/index.rst    |   1 +
 Documentation/networking/phy-port.rst | 111 ++++++++++++++++++++++++++
 MAINTAINERS                           |   1 +
 3 files changed, 113 insertions(+)
 create mode 100644 Documentation/networking/phy-port.rst

diff --git a/Documentation/networking/index.rst b/Documentation/networking/index.rst
index ac90b82f3ce9..f60acc06e3f7 100644
--- a/Documentation/networking/index.rst
+++ b/Documentation/networking/index.rst
@@ -96,6 +96,7 @@ Contents:
    packet_mmap
    phonet
    phy-link-topology
+   phy-port
    pktgen
    plip
    ppp_generic
diff --git a/Documentation/networking/phy-port.rst b/Documentation/networking/phy-port.rst
new file mode 100644
index 000000000000..6d9d46ebe438
--- /dev/null
+++ b/Documentation/networking/phy-port.rst
@@ -0,0 +1,111 @@
+.. SPDX-License-Identifier: GPL-2.0
+.. _phy_port:
+
+=================
+Ethernet ports
+=================
+
+This document is a basic description of the phy_port infrastructure,
+introduced to represent physical interfaces of Ethernet devices.
+
+Without phy_port, we already have quite a lot of information about what the
+media-facing interface of a NIC can do and looks like, through the
+:c:type:`struct ethtool_link_ksettings <ethtool_link_ksettings>` attributes,
+which includes :
+
+ - What the NIC can do through the :c:member:`supported` field
+ - What the Link Partner advertises through :c:member:`lp_advertising`
+ - Which features we're advertising through :c:member:`advertising`
+
+We also have info about the number of lanes and the PORT type. These settings
+are built by aggregating together information reported by various devices that
+are sitting on the link :
+
+  - The NIC itself, through the :c:member:`get_link_ksettings` callback
+  - Precise information from the MAC and PCS by using phylink in the MAC driver
+  - Information reported by the PHY device
+  - Information reported by an SFP module (which can itself include a PHY)
+
+This model however starts showing its limitations when we consider devices that
+have more than one media interface. In such a case, only information about the
+actively used interface is reported, and it's not possible to know what the
+other interfaces can do. In fact, we have very few information about whether or
+not there are any other media interfaces.
+
+The goal of the phy_port representation is to provide a way of representing a
+physical interface of a NIC, regardless of what is driving the port (NIC through
+a firmware, SFP module, Ethernet PHY).
+
+Multi-port interfaces examples
+==============================
+
+Several cases of multi-interface NICs have been observed so far :
+
+Internal MII Mux::
+
+  +------------------+
+  | SoC              |
+  |          +-----+ |           +-----+
+  | +-----+  |     |-------------| PHY |
+  | | MAC |--| Mux | |   +-----+ +-----+
+  | +-----+  |     |-----| SFP |
+  |          +-----+ |   +-----+
+  +------------------+
+
+Internal Mux with internal PHY::
+
+  +------------------------+
+  | SoC                    |
+  |          +-----+ +-----+
+  | +-----+  |     |-| PHY |
+  | | MAC |--| Mux | +-----+   +-----+
+  | +-----+  |     |-----------| SFP |
+  |          +-----+       |   +-----+
+  +------------------------+
+
+External Mux::
+
+  +---------+
+  | SoC     |  +-----+  +-----+
+  |         |  |     |--| PHY |
+  | +-----+ |  |     |  +-----+
+  | | MAC |----| Mux |  +-----+
+  | +-----+ |  |     |--| PHY |
+  |         |  +-----+  +-----+
+  |         |     |
+  |    GPIO-------+
+  +---------+
+
+Double-port PHY::
+
+  +---------+
+  | SoC     | +-----+
+  |         | |     |--- RJ45
+  | +-----+ | |     |
+  | | MAC |---| PHY |   +-----+
+  | +-----+ | |     |---| SFP |
+  +---------+ +-----+   +-----+
+
+phy_port aims at providing a path to support all the above topologies, by
+representing the media interfaces in a way that's agnostic to what's driving
+the interface. the struct phy_port object has its own set of callback ops, and
+will eventually be able to report its own ksettings::
+
+             _____      +------+
+            (     )-----| Port |
+ +-----+   (       )    +------+
+ | MAC |--(   ???   )
+ +-----+   (       )    +------+
+            (_____)-----| Port |
+                        +------+
+
+Next steps
+==========
+
+As of writing this documentation, only ports controlled by PHY devices are
+supported. The next steps will be to add the Netlink API to expose these
+to userspace and add support for raw ports (controlled by some firmware, and directly
+managed by the NIC driver).
+
+Another parallel task is the introduction of a MII muxing framework to allow the
+control of non-PHY driver multi-port setups.
diff --git a/MAINTAINERS b/MAINTAINERS
index 10d7548d440e..2db2b0d22c6a 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -8950,6 +8950,7 @@ F:	Documentation/devicetree/bindings/net/ethernet-connector.yaml
 F:	Documentation/devicetree/bindings/net/ethernet-phy.yaml
 F:	Documentation/devicetree/bindings/net/mdio*
 F:	Documentation/devicetree/bindings/net/qca,ar803x.yaml
+F:	Documentation/networking/phy-port.rst
 F:	Documentation/networking/phy.rst
 F:	drivers/net/mdio/
 F:	drivers/net/mdio/acpi_mdio.c
-- 
2.49.0

Re: [PATCH net-next v7 04/15] net: phy: Introduce PHY ports representation

[Simon Horman]

On Mon, Jun 30, 2025 at 04:33:03PM +0200, Maxime Chevallier wrote:

...

> +/**
> + * phy_port_get_type() - get the PORT_* attribut for that port.
> + * @port: The port we want the information from
> + *
> + * Returns: A PORT_XXX value.
> + */
> +int phy_port_get_type(struct phy_port *port)
> +{
> +	if (port->mediums & ETHTOOL_LINK_MEDIUM_BASET)

Hi Maxime,

Should this be:

	if (port->mediums & BIT(ETHTOOL_LINK_MEDIUM_BASET))

Flagged by Smatch (because ETHTOOL_LINK_MEDIUM_BASET is 0,
so as-is the condition is always false).

> +		return PORT_TP;
> +
> +	if (phy_port_is_fiber(port))
> +		return PORT_FIBRE;
> +
> +	return PORT_OTHER;
> +}
> +EXPORT_SYMBOL_GPL(phy_port_get_type);

...

Re: [PATCH net-next v7 04/15] net: phy: Introduce PHY ports representation

[Maxime Chevallier]

On Tue, 1 Jul 2025 14:02:43 +0100
Simon Horman <horms@kernel.org> wrote:

> On Mon, Jun 30, 2025 at 04:33:03PM +0200, Maxime Chevallier wrote:
> 
> ...
> 
> > +/**
> > + * phy_port_get_type() - get the PORT_* attribut for that port.
> > + * @port: The port we want the information from
> > + *
> > + * Returns: A PORT_XXX value.
> > + */
> > +int phy_port_get_type(struct phy_port *port)
> > +{
> > +	if (port->mediums & ETHTOOL_LINK_MEDIUM_BASET)  
> 
> Hi Maxime,
> 
> Should this be:
> 
> 	if (port->mediums & BIT(ETHTOOL_LINK_MEDIUM_BASET))
> 
> Flagged by Smatch (because ETHTOOL_LINK_MEDIUM_BASET is 0,
> so as-is the condition is always false).

You're absolutely correct ! Thanks...

Maxime

Re: [PATCH net-next v7 01/15] dt-bindings: net: Introduce the ethernet-connector description

[Rob Herring]

On Mon, Jun 30, 2025 at 04:33:00PM +0200, Maxime Chevallier wrote:
> The ability to describe the physical ports of Ethernet devices is useful
> to describe multi-port devices, as well as to remove any ambiguity with
> regard to the nature of the port.
> 
> Moreover, describing ports allows for a better description of features
> that are tied to connectors, such as PoE through the PSE-PD devices.
> 
> Introduce a binding to allow describing the ports, for now with 2
> attributes :
> 
>  - The number of lanes, which is a quite generic property that allows
>    differentating between multiple similar technologies such as BaseT1
>    and "regular" BaseT (which usually means BaseT4).
> 
>  - The media that can be used on that port, such as BaseT for Twisted
>    Copper, BaseC for coax copper, BaseS/L for Fiber, BaseK for backplane
>    ethernet, etc. This allows defining the nature of the port, and
>    therefore avoids the need for vendor-specific properties such as
>    "micrel,fiber-mode" or "ti,fiber-mode".
> 
> The port description lives in its own file, as it is intended in the
> future to allow describing the ports for phy-less devices.
> 
> Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
> ---
>  .../bindings/net/ethernet-connector.yaml      | 47 +++++++++++++++++++
>  .../devicetree/bindings/net/ethernet-phy.yaml | 18 +++++++
>  MAINTAINERS                                   |  1 +
>  3 files changed, 66 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/ethernet-connector.yaml
> 
> diff --git a/Documentation/devicetree/bindings/net/ethernet-connector.yaml b/Documentation/devicetree/bindings/net/ethernet-connector.yaml
> new file mode 100644
> index 000000000000..2aa28e6c1523
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/ethernet-connector.yaml
> @@ -0,0 +1,47 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/net/ethernet-connector.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Generic Ethernet Connector
> +
> +maintainers:
> +  - Maxime Chevallier <maxime.chevallier@bootlin.com>
> +
> +description:
> +  An Ethernet Connectr represents the output of a network component such as

typo

> +  a PHY, an Ethernet controller with no PHY, or an SFP module.
> +
> +properties:
> +
> +  lanes:
> +    description:
> +      Defines the number of lanes on the port, that is the number of physical
> +      channels used to convey the data with the link partner.
> +    $ref: /schemas/types.yaml#/definitions/uint32

maximum?

Or I'd guess this is power of 2 values?

> +
> +  media:
> +    description:
> +      The mediums, as defined in 802.3, that can be used on the port.
> +    items:
> +      enum:
> +        - BaseT
> +        - BaseK
> +        - BaseS
> +        - BaseC
> +        - BaseL
> +        - BaseD
> +        - BaseE
> +        - BaseF
> +        - BaseV
> +        - BaseMLD
> +        - BaseX

This can be multiple values? But then how does one know what is actually 
attached?

> +
> +required:
> +  - lanes
> +  - media
> +
> +additionalProperties: true
> +
> +...
> diff --git a/Documentation/devicetree/bindings/net/ethernet-phy.yaml b/Documentation/devicetree/bindings/net/ethernet-phy.yaml
> index 71e2cd32580f..6bf670beb66f 100644
> --- a/Documentation/devicetree/bindings/net/ethernet-phy.yaml
> +++ b/Documentation/devicetree/bindings/net/ethernet-phy.yaml
> @@ -277,6 +277,17 @@ properties:
>  
>      additionalProperties: false
>  
> +  mdi:
> +    type: object
> +
> +    patternProperties:
> +      '^connector-[a-f0-9]+$':
> +        $ref: /schemas/net/ethernet-connector.yaml#
> +
> +        unevaluatedProperties: false
> +
> +    additionalProperties: false
> +
>  required:
>    - reg
>  
> @@ -313,5 +324,12 @@ examples:
>                      default-state = "keep";
>                  };
>              };
> +
> +            mdi {
> +              connector-0 {
> +                lanes = <2>;
> +                media = "BaseT";
> +              };
> +            };
>          };
>      };
> diff --git a/MAINTAINERS b/MAINTAINERS
> index bb9df569a3ff..20806cfc1003 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -8946,6 +8946,7 @@ R:	Russell King <linux@armlinux.org.uk>
>  L:	netdev@vger.kernel.org
>  S:	Maintained
>  F:	Documentation/ABI/testing/sysfs-class-net-phydev
> +F:	Documentation/devicetree/bindings/net/ethernet-connector.yaml
>  F:	Documentation/devicetree/bindings/net/ethernet-phy.yaml
>  F:	Documentation/devicetree/bindings/net/mdio*
>  F:	Documentation/devicetree/bindings/net/qca,ar803x.yaml
> -- 
> 2.49.0
> 

Re: [PATCH net-next v7 01/15] dt-bindings: net: Introduce the ethernet-connector description

[Maxime Chevallier]

Hi Rob,

On Tue, 8 Jul 2025 10:57:33 -0500
Rob Herring <robh@kernel.org> wrote:

> On Mon, Jun 30, 2025 at 04:33:00PM +0200, Maxime Chevallier wrote:
> > The ability to describe the physical ports of Ethernet devices is useful
> > to describe multi-port devices, as well as to remove any ambiguity with
> > regard to the nature of the port.
> > 
> > Moreover, describing ports allows for a better description of features
> > that are tied to connectors, such as PoE through the PSE-PD devices.
> > 
> > Introduce a binding to allow describing the ports, for now with 2
> > attributes :
> > 
> >  - The number of lanes, which is a quite generic property that allows
> >    differentating between multiple similar technologies such as BaseT1
> >    and "regular" BaseT (which usually means BaseT4).
> > 
> >  - The media that can be used on that port, such as BaseT for Twisted
> >    Copper, BaseC for coax copper, BaseS/L for Fiber, BaseK for backplane
> >    ethernet, etc. This allows defining the nature of the port, and
> >    therefore avoids the need for vendor-specific properties such as
> >    "micrel,fiber-mode" or "ti,fiber-mode".
> > 
> > The port description lives in its own file, as it is intended in the
> > future to allow describing the ports for phy-less devices.
> > 
> > Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
> > ---
> >  .../bindings/net/ethernet-connector.yaml      | 47 +++++++++++++++++++
> >  .../devicetree/bindings/net/ethernet-phy.yaml | 18 +++++++
> >  MAINTAINERS                                   |  1 +
> >  3 files changed, 66 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/net/ethernet-connector.yaml
> > 
> > diff --git a/Documentation/devicetree/bindings/net/ethernet-connector.yaml b/Documentation/devicetree/bindings/net/ethernet-connector.yaml
> > new file mode 100644
> > index 000000000000..2aa28e6c1523
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/net/ethernet-connector.yaml
> > @@ -0,0 +1,47 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/net/ethernet-connector.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Generic Ethernet Connector
> > +
> > +maintainers:
> > +  - Maxime Chevallier <maxime.chevallier@bootlin.com>
> > +
> > +description:
> > +  An Ethernet Connectr represents the output of a network component such as  
> 
> typo
> 
> > +  a PHY, an Ethernet controller with no PHY, or an SFP module.
> > +
> > +properties:
> > +
> > +  lanes:
> > +    description:
> > +      Defines the number of lanes on the port, that is the number of physical
> > +      channels used to convey the data with the link partner.
> > +    $ref: /schemas/types.yaml#/definitions/uint32  
> 
> maximum?
> 
> Or I'd guess this is power of 2 values?

All values that exist so far are indeed power of 2 values, but that's
not a strict requirement, there may be other values one day. I'll add
all possible values (1, 2 , 4 , 8) so far.
> 
> > +
> > +  media:
> > +    description:
> > +      The mediums, as defined in 802.3, that can be used on the port.
> > +    items:
> > +      enum:
> > +        - BaseT
> > +        - BaseK
> > +        - BaseS
> > +        - BaseC
> > +        - BaseL
> > +        - BaseD
> > +        - BaseE
> > +        - BaseF
> > +        - BaseV
> > +        - BaseMLD
> > +        - BaseX  

Heh I need to remove BaseX

> 
> This can be multiple values? But then how does one know what is actually 
> attached?

I don't see a scenario where we would put multiple values actually. I
need to update the code accordingly, but if we are in the case where we
need to specify in DT which medium we use, then that means we can only
use one.

Thanks you for reviewing,

Maxime

Re: [PATCH net-next v7 04/15] net: phy: Introduce PHY ports representation

[Dan Carpenter]

Hi Maxime,

kernel test robot noticed the following build warnings:

url:    https://github.com/intel-lab-lkp/linux/commits/Maxime-Chevallier/dt-bindings-net-Introduce-the-ethernet-connector-description/20250630-224035
base:   net-next/main
patch link:    https://lore.kernel.org/r/20250630143315.250879-5-maxime.chevallier%40bootlin.com
patch subject: [PATCH net-next v7 04/15] net: phy: Introduce PHY ports representation
config: x86_64-randconfig-r071-20250706 (https://download.01.org/0day-ci/archive/20250706/202507061812.0aBYBa9l-lkp@intel.com/config)
compiler: gcc-12 (Debian 12.2.0-14+deb12u1) 12.2.0

If you fix the issue in a separate patch/commit (i.e. not just a new version of
the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <lkp@intel.com>
| Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
| Closes: https://lore.kernel.org/r/202507061812.0aBYBa9l-lkp@intel.com/

smatch warnings:
drivers/net/phy/phy_port.c:130 phy_port_get_type() warn: bitwise AND condition is false here

vim +130 drivers/net/phy/phy_port.c

055cbf51317b1e Maxime Chevallier 2025-06-30  122  /**
055cbf51317b1e Maxime Chevallier 2025-06-30  123   * phy_port_get_type() - get the PORT_* attribut for that port.
055cbf51317b1e Maxime Chevallier 2025-06-30  124   * @port: The port we want the information from
055cbf51317b1e Maxime Chevallier 2025-06-30  125   *
055cbf51317b1e Maxime Chevallier 2025-06-30  126   * Returns: A PORT_XXX value.
055cbf51317b1e Maxime Chevallier 2025-06-30  127   */
055cbf51317b1e Maxime Chevallier 2025-06-30  128  int phy_port_get_type(struct phy_port *port)
055cbf51317b1e Maxime Chevallier 2025-06-30  129  {
055cbf51317b1e Maxime Chevallier 2025-06-30 @130  	if (port->mediums & ETHTOOL_LINK_MEDIUM_BASET)
                                                                            ^^^^^^^^^^^^^^^^^^^^^^^^^
I think BIT(ETHTOOL_LINK_MEDIUM_BASET) was intended.


-- 
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki