From: Dolev Raviv <draviv@codeaurora.org>
To: James.Bottomley@HansenPartnership.com, hch@infradead.org
Cc: linux-scsi@vger.kernel.org, linux-scsi-owner@vger.kernel.org,
linux-arm-msm@vger.kernel.org, santoshsy@gmail.com,
Dolev Raviv <draviv@codeaurora.org>
Subject: [PATCH/RFC V2 00/16] UFS: Power managment support
Date: Thu, 14 Aug 2014 16:30:51 +0300 [thread overview]
Message-ID: <1408023067-26103-1-git-send-email-draviv@codeaurora.org> (raw)
This patch seies introduces support for power managment in the driver as well as vendor specific initialization - registers, clocks, voltage regulators etc.
It includes also a rework for the init sequnce and other PM pre-requisit such as write protection support, handling well-known LUN, error handling (retries), bkops, START_STOP unit command, and ICC levels settings.
--
Changes from V1:
- 6 new patches apended at the end
- Allow overriding power configuration with controller support and
preferences/capabilities <Dolev Raviv>
- Allow overriding power choice with controller capabilities <Dolev Raviv>
- Add support for clock gating and clock scaling <Sahitya Tummala>
- Add capability to control the auto bkops during suspend <Subhash Jadavani>
- Add misc changes for phy/unipro driver usage <Dolev Raviv>
Dolev Raviv (2):
scsi: ufs: refactor configuring power mode
scsi: ufs: definitions for phy interface
Sahitya Tummala (3):
scsi: ufs: Add support for clock gating
scsi: ufs: Add freq-table-hz property for UFS device
scsi: ufs: Add support for clock scaling using devfreq framework
Subhash Jadavani (5):
scsi: ufs: refactor query descriptor API support
scsi: support well known logical units
scsi: ufs: introduce well known logical unit in ufs
scsi: ufs: add UFS power management support
scsi: ufs: add capability to control the auto bkops during suspend
Sujit Reddy Thumma (5):
scsi: ufs: Allow vendor specific initialization
scsi: ufs: Add regulator enable support
scsi: ufs: Add clock initialization support
scsi: ufs: improve init sequence
scsi: sd: Avoid sending medium write commands if device is write
protected
Yaniv Gardi (1):
scsi: ufs: Active Power Mode - configuring bActiveICCLevel
.../devicetree/bindings/ufs/ufshcd-pltfrm.txt | 37 +
drivers/scsi/scsi_scan.c | 16 +
drivers/scsi/scsi_sysfs.c | 7 +
drivers/scsi/sd.c | 6 +-
drivers/scsi/ufs/Kconfig | 2 +
drivers/scsi/ufs/ufs.h | 131 +-
drivers/scsi/ufs/ufshcd-pci.c | 55 +-
drivers/scsi/ufs/ufshcd-pltfrm.c | 282 ++-
drivers/scsi/ufs/ufshcd.c | 2400 ++++++++++++++++++--
drivers/scsi/ufs/ufshcd.h | 277 ++-
drivers/scsi/ufs/ufshci.h | 9 +-
drivers/scsi/ufs/unipro.h | 56 +
include/scsi/scsi.h | 1 +
include/scsi/scsi_host.h | 5 +
14 files changed, 2959 insertions(+), 325 deletions(-)
--
1.8.5.2
next reply other threads:[~2014-08-14 13:31 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-08-14 13:30 Dolev Raviv [this message]
2014-08-14 13:30 ` [PATCH/RFC V2 01/16] scsi: ufs: Allow vendor specific initialization Dolev Raviv
2014-08-14 13:30 ` [PATCH/RFC V2 02/16] scsi: ufs: Add regulator enable support Dolev Raviv
2014-08-14 13:30 ` [PATCH/RFC V2 03/16] scsi: ufs: Add clock initialization support Dolev Raviv
2014-08-14 13:30 ` [PATCH/RFC V2 04/16] scsi: ufs: refactor query descriptor API support Dolev Raviv
2014-08-14 13:30 ` [PATCH/RFC V2 05/16] scsi: ufs: improve init sequence Dolev Raviv
2014-08-14 13:30 ` [PATCH/RFC V2 06/16] scsi: ufs: Active Power Mode - configuring bActiveICCLevel Dolev Raviv
2014-08-14 13:30 ` [PATCH/RFC V2 07/16] scsi: support well known logical units Dolev Raviv
2014-08-19 17:22 ` Christoph Hellwig
2014-08-21 21:18 ` Martin K. Petersen
2014-08-14 13:30 ` [PATCH/RFC V2 08/16] scsi: ufs: introduce well known logical unit in ufs Dolev Raviv
2014-08-14 13:31 ` [PATCH/RFC V2 09/16] scsi: sd: Avoid sending medium write commands if device is write protected Dolev Raviv
2014-08-14 13:31 ` [PATCH/RFC V2 10/16] scsi: ufs: add UFS power management support Dolev Raviv
2014-08-20 7:20 ` Dong, Chuanxiao
2014-08-21 8:59 ` Dong, Chuanxiao
2014-08-21 13:01 ` hch
2014-09-03 13:04 ` Dolev Raviv
2014-09-03 11:43 ` Dolev Raviv
2014-08-14 13:31 ` [PATCH/RFC V2 11/16] scsi: ufs: refactor configuring power mode Dolev Raviv
2014-08-14 13:31 ` [PATCH/RFC V2 12/16] scsi: ufs: Add support for clock gating Dolev Raviv
2014-08-14 13:31 ` [PATCH/RFC V2 13/16] scsi: ufs: Add freq-table-hz property for UFS device Dolev Raviv
2014-08-14 13:31 ` [PATCH/RFC V2 14/16] scsi: ufs: Add support for clock scaling using devfreq framework Dolev Raviv
2014-08-14 13:31 ` [PATCH/RFC V2 15/16] scsi: ufs: add capability to control the auto bkops during suspend Dolev Raviv
2014-08-14 13:31 ` [PATCH/RFC V2 16/16] scsi: ufs: definitions for phy interface Dolev Raviv
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1408023067-26103-1-git-send-email-draviv@codeaurora.org \
--to=draviv@codeaurora.org \
--cc=James.Bottomley@HansenPartnership.com \
--cc=hch@infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-scsi-owner@vger.kernel.org \
--cc=linux-scsi@vger.kernel.org \
--cc=santoshsy@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).