Re: [PATCH v2 2/2] leds: add Qualcomm PM8941 WLED driver

["Ivan T. Ivanov" <iivanov-NEYub+7Iv8PQT0dZR+AlfA@public.gmane.org>]

Hi Bjorn,

Just few nitpick comments. 

On Fri, 2015-01-23 at 16:54 -0800, Bjorn Andersson wrote:
> From: Courtney Cavin cavin-/MT0OVThwyLZJqsBc5GL+g@public.gmane.org>
> 
> This adds support for the WLED ('White' LED) block on Qualcomm's
> PM8941 PMICs.
> 
> Signed-off-by: Courtney Cavin cavin-/MT0OVThwyLZJqsBc5GL+g@public.gmane.org>
> Signed-off-by: Bjorn Andersson andersson-/MT0OVThwyLZJqsBc5GL+g@public.gmane.org>
> ---
>  drivers/leds/Kconfig            |   8 +
>  drivers/leds/Makefile           |   1 +
>  drivers/leds/leds-pm8941-wled.c | 459 ++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 468 insertions(+)
>  create mode 100644 drivers/leds/leds-pm8941-wled.c
> 

<snip>

> +
> +#define PM8941_WLED_REG_VAL_BASE               0x40
> +#define  PM8941_WLED_REG_VAL_MAX               0xFFF
> +
> +#define PM8941_WLED_REG_MOD_EN                 0x46
> +#define  PM8941_WLED_REG_MOD_EN_BIT            BIT(7)
> +#define  PM8941_WLED_REG_MOD_EN_MASK           BIT(7)

Is it possible bit definitions to have same indentation like registers offsets?

> 
> +struct pm8941_wled_config {
> +       u32 i_boost_limit;
> +       u32 ovp;
> +       u32 switch_freq;
> +       u32 num_strings;
> +       u32 i_limit;
> +       bool cs_out_en;
> +       bool ext_gen;
> +       bool cabc_en;
> +};
> +

Could this be further squashed to bellow structure?

> +struct pm8941_wled {
> +       struct regmap *regmap;
> +       u16 addr;
> +
> +       struct led_classdev cdev;
> +
> +       struct pm8941_wled_config cfg;
> +};
> +
> 

<snip>

> +static void pm8941_wled_set_brightness(struct led_classdev *cdev,
> +                                                                                       enum 
> led_brightness value)
> +{
> +       if (pm8941_wled_set(cdev, value)) {

pm8941_wled_set() is used only here, could it be merged into this function?
 
> +               dev_err(cdev->dev, "Unable to set brightness\n");
> +               return;
> +       }
> +       cdev->brightness = value;
> +}
> +
> 

Otherwise it looks good. Driver is loaded and device is detected
properly (i have added readings for type and subtype registers).
Do you know where I can measure result from changing brightness 
sysfs entry. I am using 8074 dragonboard?

Thank you,
Ivan
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html