From: Yaniv Gardi <ygardi@codeaurora.org>
To: James.Bottomley@HansenPartnership.com, pebolle@tiscali.nl,
hch@infradead.org
Cc: linux-kernel@vger.kernel.org, linux-scsi@vger.kernel.org,
linux-arm-msm@vger.kernel.org, santoshsy@gmail.com,
linux-scsi-owner@vger.kernel.org, subhashj@codeaurora.org,
ygardi@codeaurora.org, gbroner@codeaurora.org,
draviv@codeaurora.org, Vinayak Holikatti <vinholikatti@gmail.com>,
"James E.J. Bottomley" <JBottomley@odin.com>
Subject: [PATCH v1 03/17] scsi: ufs: optimize system suspend handling
Date: Sun, 13 Sep 2015 17:52:43 +0300 [thread overview]
Message-ID: <1442155977-7686-4-git-send-email-ygardi@codeaurora.org> (raw)
In-Reply-To: <1442155977-7686-1-git-send-email-ygardi@codeaurora.org>
Consider following sequence of events:
1. UFS is runtime suspended, link_state = Hibern8, device_state = sleep
2. System goes into system suspend, ufshcd_system_suspend() brings both
link and device to active state and then puts the device in
Power_Down state and link in OFF state.
3. System resumes at some later point in time, ufshcd_system_resume()
doesn't do anything as UFS state is runtime suspended. Note that
link is still on OFF state and device is in Power_Down state.
4. Now system again goes into suspend without any UFS accesses
before it.
ufshcd_system_suspend() again brings both link and device to active
state and then puts the device in Power_Down state and link if OFF
state. But it's unnecessary to bring the link & device in active
state as both link and device are already in desired low power
states. This change fixes this issue by adding proper state checks
in ufshcd_system_suspend().
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
---
drivers/scsi/ufs/ufshcd.c | 15 ++++++---------
1 file changed, 6 insertions(+), 9 deletions(-)
diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
index 388536e..9e3ec01 100644
--- a/drivers/scsi/ufs/ufshcd.c
+++ b/drivers/scsi/ufs/ufshcd.c
@@ -5464,16 +5464,13 @@ int ufshcd_system_suspend(struct ufs_hba *hba)
if (!hba || !hba->is_powered)
return 0;
- if (pm_runtime_suspended(hba->dev)) {
- if (hba->rpm_lvl == hba->spm_lvl)
- /*
- * There is possibility that device may still be in
- * active state during the runtime suspend.
- */
- if ((ufs_get_pm_lvl_to_dev_pwr_mode(hba->spm_lvl) ==
- hba->curr_dev_pwr_mode) && !hba->auto_bkops_enabled)
- goto out;
+ if ((ufs_get_pm_lvl_to_dev_pwr_mode(hba->spm_lvl) ==
+ hba->curr_dev_pwr_mode) &&
+ (ufs_get_pm_lvl_to_link_pwr_state(hba->spm_lvl) ==
+ hba->uic_link_state))
+ goto out;
+ if (pm_runtime_suspended(hba->dev)) {
/*
* UFS device and/or UFS link low power states during runtime
* suspend seems to be different than what is expected during
--
1.8.5.2
--
QUALCOMM ISRAEL, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
next prev parent reply other threads:[~2015-09-13 14:52 UTC|newest]
Thread overview: 33+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-09-13 14:52 [PATCH v1 00/17] add fixes, device quirks, error recovery, Yaniv Gardi
[not found] ` <1442155977-7686-1-git-send-email-ygardi-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2015-09-13 14:52 ` [PATCH v1 01/17] scsi: ufs-qcom: add number of lanes per direction Yaniv Gardi
2015-10-21 15:47 ` Akinobu Mita
2015-09-13 14:52 ` [PATCH v1 02/17] scsi: ufs: add option to change default UFS power management level Yaniv Gardi
2015-10-21 15:51 ` Akinobu Mita
2015-10-26 13:04 ` ygardi
2015-09-13 14:52 ` Yaniv Gardi [this message]
2015-09-13 14:52 ` [PATCH v1 04/17] scsi: ufs: avoid spurious UFS host controller interrupts Yaniv Gardi
2015-09-13 14:52 ` [PATCH v1 05/17] scsi: ufs: implement scsi host timeout handler Yaniv Gardi
2015-09-13 14:52 ` [PATCH v1 06/17] scsi :ufs: verify hba controller hce reg value Yaniv Gardi
2015-10-21 15:53 ` Akinobu Mita
2015-10-26 13:11 ` ygardi
2015-09-13 14:52 ` [PATCH v1 07/17] scsi: ufs: separate device and host quirks Yaniv Gardi
2015-10-21 15:59 ` Akinobu Mita
2015-10-26 13:30 ` ygardi
2015-09-13 14:52 ` [PATCH v1 08/17] scsi: ufs: split broken LCC quirk Yaniv Gardi
2015-10-21 16:00 ` Akinobu Mita
2015-10-26 13:58 ` ygardi
2015-09-13 14:52 ` [PATCH v1 09/17] scsi: ufs: disable vccq if it's not needed by UFS device Yaniv Gardi
2015-09-13 14:52 ` [PATCH v1 10/17] scsi: ufs: make error handling bit faster Yaniv Gardi
2015-09-13 14:52 ` [PATCH v1 11/17] scsi: ufs: add error recovery after DL NAC error Yaniv Gardi
2015-09-13 14:52 ` [PATCH v1 12/17] scsi: ufs: add retry for query descriptors Yaniv Gardi
2015-10-21 16:05 ` Akinobu Mita
2015-10-26 14:03 ` ygardi
2015-09-13 14:52 ` [PATCH v1 13/17] scsi: ufs: handle non spec compliant bkops behaviour by device Yaniv Gardi
2015-09-13 14:52 ` [PATCH v1 14/17] scsi: ufs: tune UniPro parameters to optimize hibern8 exit time Yaniv Gardi
2015-10-21 16:10 ` Akinobu Mita
2015-10-26 14:32 ` ygardi
2015-09-13 14:52 ` [PATCH v1 15/17] scsi: ufs: fix leakage during link off state Yaniv Gardi
2015-09-13 14:52 ` [PATCH v1 16/17] scsi: ufs: add delay before putting UFS rails in low power modes Yaniv Gardi
2015-10-21 16:11 ` Akinobu Mita
2015-10-26 15:08 ` ygardi
2015-09-13 14:52 ` [PATCH v1 17/17] scsi: ufs-qcom: set PA_Local_TX_LCC_Enable before link startup Yaniv Gardi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1442155977-7686-4-git-send-email-ygardi@codeaurora.org \
--to=ygardi@codeaurora.org \
--cc=JBottomley@odin.com \
--cc=James.Bottomley@HansenPartnership.com \
--cc=draviv@codeaurora.org \
--cc=gbroner@codeaurora.org \
--cc=hch@infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-scsi-owner@vger.kernel.org \
--cc=linux-scsi@vger.kernel.org \
--cc=pebolle@tiscali.nl \
--cc=santoshsy@gmail.com \
--cc=subhashj@codeaurora.org \
--cc=vinholikatti@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).