linux-arm-msm.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Yaniv Gardi <ygardi@codeaurora.org>
To: James.Bottomley@HansenPartnership.com
Cc: linux-kernel@vger.kernel.org, linux-scsi@vger.kernel.org,
	linux-arm-msm@vger.kernel.org, santoshsy@gmail.com,
	linux-scsi-owner@vger.kernel.org, ygardi@codeaurora.org
Subject: [PATCH v8 00/17] add fixes, device quirks, error recovery,
Date: Thu, 10 Mar 2016 17:37:04 +0200	[thread overview]
Message-ID: <1457624241-20525-1-git-send-email-ygardi@codeaurora.org> (raw)

V8:
fixed cyclic dependency by removing ufs_quirk.c that was previously added
in V7 06/17, and moving its code into ufshcd.c

V7:
updated patches with "Reviewed-by" and "Acked-by" tags

V6:
as per comment, patch 15/15 in V5 was divided into 3 patches in V6

V5:
as per comment, patch 05/14 in V4, was divided into 2 patches in V5

V4:
fixed DOS EOL symbols in 2 new files

V3:
Due to comments in V2
Removed change 02/17 of V2 
Removed change 03/17 of V2
Removed change 17/17 of V2

V2:
This series should be pushed on top of 15 patches series:
"Big fixes, retries, handle a race condition"
fixed and few comments.

V1:
This series should be pushed on top of 15 patches series:
"Big fixes, retries, handle a race condition"


Yaniv Gardi (15):
  scsi: ufs-qcom: add number of lanes per direction
  scsi: ufs: avoid spurious UFS host controller interrupts
  scsi: ufs: implement scsi host timeout handler
  scsi: ufs: verify hba controller hce reg value
  scsi: ufs: add support to read device and string descriptors
  scsi: ufs: separate device and host quirks
  scsi: ufs: disable vccq if it's not needed by UFS device
  scsi: ufs: make error handling bit faster
  scsi: ufs: add error recovery after DL NAC error
  scsi: ufs: add retry for query descriptors
  scsi: ufs: handle non spec compliant bkops behaviour by device
  scsi: ufs: tune UniPro parameters to optimize hibern8 exit time
  scsi: ufs: fix leakage during link off state
  scsi: ufs: add device quirk delay before putting UFS rails in LPM
  scsi: ufs-qcom: set PA_Local_TX_LCC_Enable before link startup
  scsi: ufs-qcom: enable/disable the device ref clock
  scsi: ufs-qcom: add printouts of testbus debug registers

 .../devicetree/bindings/ufs/ufshcd-pltfrm.txt      |   3 +
 drivers/scsi/ufs/ufs-qcom.c                        | 155 +++-
 drivers/scsi/ufs/ufs-qcom.h                        |   9 +
 drivers/scsi/ufs/ufs.h                             |  33 +
 drivers/scsi/ufs/ufs_quirks.h                      | 151 ++++
 drivers/scsi/ufs/ufshcd-pltfrm.c                   |  19 +
 drivers/scsi/ufs/ufshcd.c                          | 818 ++++++++++++++++++---
 drivers/scsi/ufs/ufshcd.h                          |  40 +-
 drivers/scsi/ufs/ufshci.h                          |   4 +
 drivers/scsi/ufs/unipro.h                          |  22 +
 10 files changed, 1127 insertions(+), 127 deletions(-)
 create mode 100644 drivers/scsi/ufs/ufs_quirks.h

-- 
1.8.5.2

-- 
QUALCOMM ISRAEL, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation

             reply	other threads:[~2016-03-10 15:37 UTC|newest]

Thread overview: 21+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2016-03-10 15:37 Yaniv Gardi [this message]
2016-03-10 15:37 ` [PATCH v8 01/17] scsi: ufs-qcom: add number of lanes per direction Yaniv Gardi
2016-03-10 15:37 ` [PATCH v8 02/17] scsi: ufs: avoid spurious UFS host controller interrupts Yaniv Gardi
2016-03-10 15:37 ` [PATCH v8 03/17] scsi: ufs: implement scsi host timeout handler Yaniv Gardi
2016-03-10 15:37 ` [PATCH v8 04/17] scsi: ufs: verify hba controller hce reg value Yaniv Gardi
2016-03-10 15:37 ` [PATCH v8 05/17] scsi: ufs: add support to read device and string descriptors Yaniv Gardi
2016-03-10 15:37 ` [PATCH v8 06/17] scsi: ufs: separate device and host quirks Yaniv Gardi
2016-03-10 15:37 ` [PATCH v8 07/17] scsi: ufs: disable vccq if it's not needed by UFS device Yaniv Gardi
2016-03-10 15:37 ` [PATCH v8 08/17] scsi: ufs: make error handling bit faster Yaniv Gardi
2016-03-10 15:37 ` [PATCH v8 09/17] scsi: ufs: add error recovery after DL NAC error Yaniv Gardi
2016-03-10 15:37 ` [PATCH v8 10/17] scsi: ufs: add retry for query descriptors Yaniv Gardi
2016-03-10 15:37 ` [PATCH v8 11/17] scsi: ufs: handle non spec compliant bkops behaviour by device Yaniv Gardi
2016-03-10 15:37 ` [PATCH v8 12/17] scsi: ufs: tune UniPro parameters to optimize hibern8 exit time Yaniv Gardi
2016-03-10 15:37 ` [PATCH v8 13/17] scsi: ufs: fix leakage during link off state Yaniv Gardi
2016-03-10 15:37 ` [PATCH v8 14/17] scsi: ufs: add device quirk delay before putting UFS rails in LPM Yaniv Gardi
2016-03-10 15:37 ` [PATCH v8 15/17] scsi: ufs-qcom: set PA_Local_TX_LCC_Enable before link startup Yaniv Gardi
2016-03-10 15:37 ` [PATCH v8 16/17] scsi: ufs-qcom: enable/disable the device ref clock Yaniv Gardi
2016-03-10 15:37 ` [PATCH v8 17/17] scsi: ufs-qcom: add printouts of testbus debug registers Yaniv Gardi
2016-03-11  2:36 ` [PATCH v8 00/17] add fixes, device quirks, error recovery, Martin K. Petersen
2016-03-11  8:51   ` Hannes Reinecke
2016-03-14 19:59 ` Martin K. Petersen

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1457624241-20525-1-git-send-email-ygardi@codeaurora.org \
    --to=ygardi@codeaurora.org \
    --cc=James.Bottomley@HansenPartnership.com \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-scsi-owner@vger.kernel.org \
    --cc=linux-scsi@vger.kernel.org \
    --cc=santoshsy@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).