linux-arm-msm.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
To: bjorn.andersson@linaro.org
Cc: sboyd@codeaurora.org, agross@codeaurora.org,
	linux-arm-msm@vger.kernel.org,
	Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
Subject: [PATCH v4 06/10] remoteproc: qcom: Modify clock enable and disable routine
Date: Wed, 16 Nov 2016 22:31:32 +0530	[thread overview]
Message-ID: <1479315696-15490-7-git-send-email-akdwived@codeaurora.org> (raw)
In-Reply-To: <1479315696-15490-1-git-send-email-akdwived@codeaurora.org>

Clock handling is made generic than need to add new clock
every time when required to support new hexagon version.
also where ever required invoking clock enable disable
routine is replaced by this new prototype. Also clock disable
interface is separated out into two separate routine to handle
proxy clock alone unvoting when handover interrupt is arrived.

Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
---
 drivers/remoteproc/qcom_q6v5_pil.c | 90 +++++++++++++++++++++++++++-----------
 1 file changed, 65 insertions(+), 25 deletions(-)

diff --git a/drivers/remoteproc/qcom_q6v5_pil.c b/drivers/remoteproc/qcom_q6v5_pil.c
index 57c67e1..fe7c409 100644
--- a/drivers/remoteproc/qcom_q6v5_pil.c
+++ b/drivers/remoteproc/qcom_q6v5_pil.c
@@ -127,10 +127,6 @@ struct q6v5 {
 	struct qcom_smem_state *state;
 	unsigned stop_bit;
 
-
-	struct clk *ahb_clk;
-	struct clk *axi_clk;
-	struct clk *rom_clk;
 	struct clk **active_clks;
 	struct clk **proxy_clks;
 	struct reg_info *active_regs;
@@ -293,6 +289,52 @@ static void q6v5_regulator_disable(struct q6v5 *qproc)
 	q6v5_active_regulator_disable(qproc);
 }
 
+static int q6v5_clk_enable(struct device *dev, struct clk **clks,
+								int clk_count)
+{
+	int rc = 0;
+	int i;
+
+	for (i = 0; i < clk_count; i++) {
+		rc = clk_prepare_enable(clks[i]);
+		if (rc) {
+			dev_err(dev, "Clock enable failed\n");
+			goto err;
+		}
+	}
+
+	return 0;
+err:
+	for (i--; i >= 0; i--)
+		clk_disable_unprepare(clks[i]);
+
+	return rc;
+}
+
+static void q6v5_proxy_clk_disable(struct q6v5 *qproc)
+{
+	int i;
+	struct clk **clks = qproc->proxy_clks;
+
+	for (i = 0; i < qproc->proxy_clk_count; i++)
+		clk_disable_unprepare(clks[i]);
+}
+
+static void q6v5_active_clk_disable(struct q6v5 *qproc)
+{
+	int i;
+	struct clk **clks = qproc->proxy_clks;
+
+	for (i = 0; i < qproc->proxy_clk_count; i++)
+		clk_disable_unprepare(clks[i]);
+}
+
+static void q6v5_clk_disable(struct q6v5 *qproc)
+{
+	q6v5_proxy_clk_disable(qproc);
+	q6v5_active_clk_disable(qproc);
+}
+
 static int q6v5_load(struct rproc *rproc, const struct firmware *fw)
 {
 	struct q6v5 *qproc = rproc->priv;
@@ -589,6 +631,13 @@ static int q6v5_start(struct rproc *rproc)
 		return ret;
 	}
 
+	ret = q6v5_clk_enable(qproc->dev, qproc->proxy_clks,
+		qproc->proxy_clk_count);
+	if (ret) {
+		dev_err(qproc->dev, "failed to enable proxy clocks\n");
+		goto disable_proxy_reg;
+	}
+
 	ret = q6v5_regulator_enable(qproc, qproc->active_regs,
 		qproc->active_reg_count);
 	if (ret) {
@@ -601,17 +650,12 @@ static int q6v5_start(struct rproc *rproc)
 		goto disable_vdd;
 	}
 
-	ret = clk_prepare_enable(qproc->ahb_clk);
-	if (ret)
+	ret = q6v5_clk_enable(qproc->dev, qproc->active_clks,
+		qproc->active_clk_count);
+	if (ret) {
+		dev_err(qproc->dev, "failed to enable clocks\n");
 		goto assert_reset;
-
-	ret = clk_prepare_enable(qproc->axi_clk);
-	if (ret)
-		goto disable_ahb_clk;
-
-	ret = clk_prepare_enable(qproc->rom_clk);
-	if (ret)
-		goto disable_axi_clk;
+	}
 
 	writel(qproc->mba_phys, qproc->rmb_base + RMB_MBA_IMAGE_REG);
 
@@ -646,25 +690,23 @@ static int q6v5_start(struct rproc *rproc)
 
 	qproc->running = true;
 
-	/* TODO: All done, release the handover resources */
-
+	q6v5_proxy_clk_disable(qproc);
+	q6v5_proxy_regulator_disable(qproc);
 	return 0;
 
 halt_axi_ports:
 	q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_q6);
 	q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_modem);
 	q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_nc);
-
-	clk_disable_unprepare(qproc->rom_clk);
-disable_axi_clk:
-	clk_disable_unprepare(qproc->axi_clk);
-disable_ahb_clk:
-	clk_disable_unprepare(qproc->ahb_clk);
+	q6v5_active_clk_disable(qproc);
 assert_reset:
 	reset_control_assert(qproc->mss_restart);
 disable_vdd:
 	q6v5_active_regulator_disable(qproc);
 disable_proxy_clk:
+	q6v5_proxy_clk_disable(qproc);
+disable_proxy_reg:
+	q6v5_proxy_regulator_disable(qproc);
 	return ret;
 }
 
@@ -690,9 +732,7 @@ static int q6v5_stop(struct rproc *rproc)
 	q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_nc);
 
 	reset_control_assert(qproc->mss_restart);
-	clk_disable_unprepare(qproc->rom_clk);
-	clk_disable_unprepare(qproc->axi_clk);
-	clk_disable_unprepare(qproc->ahb_clk);
+	q6v5_clk_disable(qproc);
 	q6v5_regulator_disable(qproc);
 
 	return 0;
-- 
Qualcomm India Private Limited, on behalf of Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project.

  parent reply	other threads:[~2016-11-16 17:02 UTC|newest]

Thread overview: 12+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2016-11-16 17:01 [PATCH v4 00/10]remoteproc: qcom: Add support to hexagon q6v56 in qcom hexagon rproc driver Avaneesh Kumar Dwivedi
2016-11-16 17:01 ` [PATCH v4 01/10] remoteproc: qcom: Add and initialize private data for hexagon dsp Avaneesh Kumar Dwivedi
2016-11-16 17:01 ` [PATCH v4 02/10] remoteproc: qcom: Initialize MSS reset control handle Avaneesh Kumar Dwivedi
2016-11-16 17:01 ` [PATCH v4 03/10] remoteproc: qcom: Initialize clock and regulator handle with private data Avaneesh Kumar Dwivedi
2016-11-16 17:01 ` [PATCH v4 04/10] remoteproc: qcom: Modify regulator enable and disable interface Avaneesh Kumar Dwivedi
2016-11-16 17:01 ` [PATCH v4 05/10] remoteproc: qcom: Separate out regulator disable routine in two Avaneesh Kumar Dwivedi
2016-11-16 17:01 ` Avaneesh Kumar Dwivedi [this message]
2016-11-16 17:01 ` [PATCH v4 07/10] remoteproc: qcom: Add new routine for mss restart programming Avaneesh Kumar Dwivedi
2016-11-16 17:01 ` [PATCH v4 08/10] remoteproc: qcom: Modify reset sequence for hexagon to support q6v56 Avaneesh Kumar Dwivedi
2016-11-16 17:01 ` [PATCH v4 09/10] remoteproc: qcom: Modify stop routine for q6v56 specific step Avaneesh Kumar Dwivedi
2016-11-16 17:01 ` [PATCH v4 10/10] remoteproc: qcom: Adding required initialization for q6v5 hexagon Avaneesh Kumar Dwivedi
2016-11-16 23:03 ` [PATCH v4 00/10]remoteproc: qcom: Add support to hexagon q6v56 in qcom hexagon rproc driver Stephen Boyd

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1479315696-15490-7-git-send-email-akdwived@codeaurora.org \
    --to=akdwived@codeaurora.org \
    --cc=agross@codeaurora.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=sboyd@codeaurora.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).