From: Ritesh Harjani <riteshh@codeaurora.org>
To: ulf.hansson@linaro.org, adrian.hunter@intel.com
Cc: linux-mmc@vger.kernel.org, linux-kernel@vger.kernel.org,
shawn.lin@rock-chips.com, stummala@codeaurora.org,
georgi.djakov@linaro.org, linux-arm-msm@vger.kernel.org,
pramod.gurav@linaro.org, jeremymc@redhat.com,
venkatg@codeaurora.org, asutoshd@codeaurora.org,
subhashj@codeaurora.org, Ritesh Harjani <riteshh@codeaurora.org>
Subject: [PATCH 4/8] mmc: sdhci-msm: Reset vendor specific func register on probe
Date: Wed, 28 Dec 2016 16:36:27 +0530 [thread overview]
Message-ID: <1482923191-17362-5-git-send-email-riteshh@codeaurora.org> (raw)
In-Reply-To: <1482923191-17362-1-git-send-email-riteshh@codeaurora.org>
From: Venkat Gopalakrishnan <venkatg@codeaurora.org>
The vendor specific func register doesn't get reset when using the
software reset register. The various bootloader's could leave this
in an unknown state, hence reset this register to it's power on reset
value during probe.
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
---
drivers/mmc/host/sdhci-msm.c | 15 ++++-----------
1 file changed, 4 insertions(+), 11 deletions(-)
diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
index 5a37c29..a028568 100644
--- a/drivers/mmc/host/sdhci-msm.c
+++ b/drivers/mmc/host/sdhci-msm.c
@@ -69,6 +69,7 @@
#define CORE_DLL_CLOCK_DISABLE BIT(21)
#define CORE_VENDOR_SPEC 0x10c
+#define CORE_VENDOR_SPEC_POR_VAL 0xa1c
#define CORE_CLK_PWRSAVE BIT(1)
#define CORE_HC_MCLK_SEL_DFLT (2 << 8)
#define CORE_HC_MCLK_SEL_HS400 (3 << 8)
@@ -1197,17 +1198,9 @@ static int sdhci_msm_probe(struct platform_device *pdev)
goto clk_disable;
}
- config = readl_relaxed(msm_host->core_mem + CORE_POWER);
- config |= CORE_SW_RST;
- writel_relaxed(config, msm_host->core_mem + CORE_POWER);
-
- /* SW reset can take upto 10HCLK + 15MCLK cycles. (min 40us) */
- usleep_range(1000, 5000);
- if (readl(msm_host->core_mem + CORE_POWER) & CORE_SW_RST) {
- dev_err(&pdev->dev, "Stuck in reset\n");
- ret = -ETIMEDOUT;
- goto clk_disable;
- }
+ /* Reset the vendor spec register to power on reset state */
+ writel_relaxed(CORE_VENDOR_SPEC_POR_VAL,
+ host->ioaddr + CORE_VENDOR_SPEC);
/* Set HC_MODE_EN bit in HC_MODE register */
writel_relaxed(HC_MODE_EN, (msm_host->core_mem + CORE_HC_MODE));
--
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project.
next prev parent reply other threads:[~2016-12-28 11:06 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-12-28 11:06 [PATCH 0/8] mmc: sdhci-msm: Provide support for enhanced strobe Ritesh Harjani
2016-12-28 11:06 ` [PATCH 1/8] mmc: sdhci-msm: Factor out sdhci_msm_hc_select_mode Ritesh Harjani
2016-12-28 11:06 ` [PATCH 2/8] mmc: sdhci-msm: Factor out function to set/get msm clock rate Ritesh Harjani
2016-12-28 11:06 ` [PATCH 3/8] mmc: sdhci-msm: Factor out sdhci_msm_hs400 Ritesh Harjani
2016-12-28 11:06 ` Ritesh Harjani [this message]
2016-12-28 11:06 ` [PATCH 5/8] mmc: sdhci-msm: configure CORE_CSR_CDC_DELAY_CFG to recommended value Ritesh Harjani
2016-12-28 11:06 ` [PATCH 6/8] mmc: sdhci: Clear SDHCI_HS400_TUNING flag after platform_execute_tuning Ritesh Harjani
2016-12-28 11:06 ` [PATCH 7/8] mmc: sdhci-msm: Make HS400 tuning follow as per recommeneded HW sequence Ritesh Harjani
2016-12-28 11:06 ` [PATCH 8/8] mmc: sdhci-msm: Provide enhanced_strobe mode feature support Ritesh Harjani
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1482923191-17362-5-git-send-email-riteshh@codeaurora.org \
--to=riteshh@codeaurora.org \
--cc=adrian.hunter@intel.com \
--cc=asutoshd@codeaurora.org \
--cc=georgi.djakov@linaro.org \
--cc=jeremymc@redhat.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=pramod.gurav@linaro.org \
--cc=shawn.lin@rock-chips.com \
--cc=stummala@codeaurora.org \
--cc=subhashj@codeaurora.org \
--cc=ulf.hansson@linaro.org \
--cc=venkatg@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).