From: Abhishek Sahu <absahu@codeaurora.org>
To: sboyd@codeaurora.org, mturquette@baylibre.com
Cc: andy.gross@linaro.org, david.brown@linaro.org,
rnayak@codeaurora.org, linux-arm-msm@vger.kernel.org,
linux-soc@vger.kernel.org, linux-clk@vger.kernel.org,
linux-kernel@vger.kernel.org,
Abhishek Sahu <absahu@codeaurora.org>
Subject: [RFC v2 02/12] clk: qcom: support for alpha mode configuration
Date: Tue, 8 Aug 2017 23:54:07 +0530 [thread overview]
Message-ID: <1502216657-3342-3-git-send-email-absahu@codeaurora.org> (raw)
In-Reply-To: <1502216657-3342-1-git-send-email-absahu@codeaurora.org>
The current configuration does not fully configure PLL alpha mode
and values so this patch
1. Configures PLL_ALPHA_VAL_U for PLL which supports 40 bit alpha.
2. Adds alpha enable and alpha mode configuration support.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
---
drivers/clk/qcom/clk-alpha-pll.c | 5 +++++
drivers/clk/qcom/clk-alpha-pll.h | 3 +++
2 files changed, 8 insertions(+)
diff --git a/drivers/clk/qcom/clk-alpha-pll.c b/drivers/clk/qcom/clk-alpha-pll.c
index e6cde2d..6291048 100644
--- a/drivers/clk/qcom/clk-alpha-pll.c
+++ b/drivers/clk/qcom/clk-alpha-pll.c
@@ -123,6 +123,9 @@ void clk_alpha_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
regmap_write(regmap, off + PLL_CONFIG_CTL_U,
config->config_ctl_hi_val);
+ if (!(pll->flags & SUPPORTS_16BIT_ALPHA))
+ regmap_write(regmap, off + PLL_ALPHA_VAL_U, config->alpha_hi);
+
val = config->main_output_mask;
val |= config->aux_output_mask;
val |= config->aux2_output_mask;
@@ -130,6 +133,8 @@ void clk_alpha_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
val |= config->pre_div_val;
val |= config->post_div_val;
val |= config->vco_val;
+ val |= config->alpha_en_mask;
+ val |= config->alpha_mode_mask;
mask = config->main_output_mask;
mask |= config->aux_output_mask;
diff --git a/drivers/clk/qcom/clk-alpha-pll.h b/drivers/clk/qcom/clk-alpha-pll.h
index bbd6aa9..39686db 100644
--- a/drivers/clk/qcom/clk-alpha-pll.h
+++ b/drivers/clk/qcom/clk-alpha-pll.h
@@ -59,12 +59,15 @@ struct clk_alpha_pll_postdiv {
struct alpha_pll_config {
u32 l;
u32 alpha;
+ u32 alpha_hi;
u32 config_ctl_val;
u32 config_ctl_hi_val;
u32 main_output_mask;
u32 aux_output_mask;
u32 aux2_output_mask;
u32 early_output_mask;
+ u32 alpha_en_mask;
+ u32 alpha_mode_mask;
u32 pre_div_val;
u32 pre_div_mask;
u32 post_div_val;
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
next prev parent reply other threads:[~2017-08-08 18:24 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-08-08 18:24 [RFC v2 00/12] Misc patches for QCOM clocks Abhishek Sahu
2017-08-08 18:24 ` [RFC v2 01/12] clk: qcom: flag for 64 bit CONFIG_CTL Abhishek Sahu
2017-08-08 18:24 ` Abhishek Sahu [this message]
2017-08-08 18:24 ` [RFC v2 03/12] clk: qcom: use offset from alpha pll node Abhishek Sahu
2017-08-08 18:24 ` [RFC v2 04/12] clk: qcom: fix 16 bit alpha support calculation Abhishek Sahu
2017-08-08 18:24 ` [RFC v2 05/12] clk: qcom: support for dynamic updating the PLL Abhishek Sahu
2017-08-08 18:24 ` [RFC v2 06/12] clk: qcom: add flag for VCO operation Abhishek Sahu
2017-08-08 18:24 ` [RFC v2 07/12] clk: qcom: support for Huayra PLL Abhishek Sahu
2017-08-08 18:24 ` [RFC v2 08/12] clk: qcom: support for Brammo PLL Abhishek Sahu
2017-08-08 18:24 ` [RFC v2 09/12] clk: qcom: support for 2 bit PLL post divider Abhishek Sahu
2017-08-08 18:24 ` [RFC v2 10/12] clk: qcom: add read-only alpha pll post divider operations Abhishek Sahu
2017-08-08 18:24 ` [RFC v2 11/12] clk: qcom: add read-only " Abhishek Sahu
2017-08-08 18:24 ` [RFC v2 12/12] clk: qcom: add parent map for regmap mux Abhishek Sahu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1502216657-3342-3-git-send-email-absahu@codeaurora.org \
--to=absahu@codeaurora.org \
--cc=andy.gross@linaro.org \
--cc=david.brown@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-soc@vger.kernel.org \
--cc=mturquette@baylibre.com \
--cc=rnayak@codeaurora.org \
--cc=sboyd@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).