From: Abhishek Sahu <absahu@codeaurora.org>
To: sboyd@codeaurora.org, mturquette@baylibre.com
Cc: andy.gross@linaro.org, david.brown@linaro.org,
rnayak@codeaurora.org, linux-arm-msm@vger.kernel.org,
linux-soc@vger.kernel.org, linux-clk@vger.kernel.org,
linux-kernel@vger.kernel.org,
Abhishek Sahu <absahu@codeaurora.org>
Subject: [RFC v2 06/12] clk: qcom: add flag for VCO operation
Date: Tue, 8 Aug 2017 23:54:11 +0530 [thread overview]
Message-ID: <1502216657-3342-7-git-send-email-absahu@codeaurora.org> (raw)
In-Reply-To: <1502216657-3342-1-git-send-email-absahu@codeaurora.org>
Some of the Alpha PLL’s does not have VCO configuration so this
patch adds the flag and does not perform VCO operation if this
flag is set.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
---
drivers/clk/qcom/clk-alpha-pll.c | 19 +++++++++++--------
drivers/clk/qcom/clk-alpha-pll.h | 1 +
2 files changed, 12 insertions(+), 8 deletions(-)
diff --git a/drivers/clk/qcom/clk-alpha-pll.c b/drivers/clk/qcom/clk-alpha-pll.c
index 1f37bf8a..c368e7c 100644
--- a/drivers/clk/qcom/clk-alpha-pll.c
+++ b/drivers/clk/qcom/clk-alpha-pll.c
@@ -467,10 +467,12 @@ static int clk_alpha_pll_set_rate(struct clk_hw *hw, unsigned long rate,
u64 a;
rate = alpha_pll_round_rate(rate, prate, &l, &a, alpha_width);
- vco = alpha_pll_find_vco(pll, rate);
- if (!vco) {
- pr_err("alpha pll not in a valid vco range\n");
- return -EINVAL;
+ if (!(pll->flags & SUPPORTS_NO_VCO)) {
+ vco = alpha_pll_find_vco(pll, rate);
+ if (!vco) {
+ pr_err("alpha pll not in a valid vco range\n");
+ return -EINVAL;
+ }
}
regmap_write(pll->clkr.regmap, pll_l(pll), l);
@@ -483,9 +485,10 @@ static int clk_alpha_pll_set_rate(struct clk_hw *hw, unsigned long rate,
regmap_write(pll->clkr.regmap, pll_alpha(pll), a);
- regmap_update_bits(pll->clkr.regmap, pll_user_ctl(pll),
- PLL_VCO_MASK << PLL_VCO_SHIFT,
- vco->val << PLL_VCO_SHIFT);
+ if (!(pll->flags & SUPPORTS_NO_VCO))
+ regmap_update_bits(pll->clkr.regmap, pll_user_ctl(pll),
+ PLL_VCO_MASK << PLL_VCO_SHIFT,
+ vco->val << PLL_VCO_SHIFT);
regmap_update_bits(pll->clkr.regmap, pll_user_ctl(pll), PLL_ALPHA_EN,
PLL_ALPHA_EN);
@@ -505,7 +508,7 @@ static long clk_alpha_pll_round_rate(struct clk_hw *hw, unsigned long rate,
unsigned long min_freq, max_freq;
rate = alpha_pll_round_rate(rate, *prate, &l, &a, alpha_width);
- if (alpha_pll_find_vco(pll, rate))
+ if ((pll->flags & SUPPORTS_NO_VCO) || alpha_pll_find_vco(pll, rate))
return rate;
min_freq = pll->vco_table[0].min_freq;
diff --git a/drivers/clk/qcom/clk-alpha-pll.h b/drivers/clk/qcom/clk-alpha-pll.h
index 8b27c05..973673b 100644
--- a/drivers/clk/qcom/clk-alpha-pll.h
+++ b/drivers/clk/qcom/clk-alpha-pll.h
@@ -55,6 +55,7 @@ struct clk_alpha_pll {
#define SUPPORTS_FSM_MODE BIT(2)
#define SUPPORTS_64BIT_CONFIG_CTL BIT(3)
#define SUPPORTS_DYNAMIC_UPDATE BIT(4)
+#define SUPPORTS_NO_VCO BIT(5)
u8 flags;
struct clk_regmap clkr;
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
next prev parent reply other threads:[~2017-08-08 18:24 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-08-08 18:24 [RFC v2 00/12] Misc patches for QCOM clocks Abhishek Sahu
2017-08-08 18:24 ` [RFC v2 01/12] clk: qcom: flag for 64 bit CONFIG_CTL Abhishek Sahu
2017-08-08 18:24 ` [RFC v2 02/12] clk: qcom: support for alpha mode configuration Abhishek Sahu
2017-08-08 18:24 ` [RFC v2 03/12] clk: qcom: use offset from alpha pll node Abhishek Sahu
2017-08-08 18:24 ` [RFC v2 04/12] clk: qcom: fix 16 bit alpha support calculation Abhishek Sahu
2017-08-08 18:24 ` [RFC v2 05/12] clk: qcom: support for dynamic updating the PLL Abhishek Sahu
2017-08-08 18:24 ` Abhishek Sahu [this message]
2017-08-08 18:24 ` [RFC v2 07/12] clk: qcom: support for Huayra PLL Abhishek Sahu
2017-08-08 18:24 ` [RFC v2 08/12] clk: qcom: support for Brammo PLL Abhishek Sahu
2017-08-08 18:24 ` [RFC v2 09/12] clk: qcom: support for 2 bit PLL post divider Abhishek Sahu
2017-08-08 18:24 ` [RFC v2 10/12] clk: qcom: add read-only alpha pll post divider operations Abhishek Sahu
2017-08-08 18:24 ` [RFC v2 11/12] clk: qcom: add read-only " Abhishek Sahu
2017-08-08 18:24 ` [RFC v2 12/12] clk: qcom: add parent map for regmap mux Abhishek Sahu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1502216657-3342-7-git-send-email-absahu@codeaurora.org \
--to=absahu@codeaurora.org \
--cc=andy.gross@linaro.org \
--cc=david.brown@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-soc@vger.kernel.org \
--cc=mturquette@baylibre.com \
--cc=rnayak@codeaurora.org \
--cc=sboyd@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).