From: Manu Gautam <mgautam@codeaurora.org>
To: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <balbi@kernel.org>,
linux-arm-msm@vger.kernel.org, linux-usb@vger.kernel.org,
Manu Gautam <mgautam@codeaurora.org>
Subject: [PATCH v2 00/17] Support for Qualcomm QUSBv2 and QMPv3 USB PHYs
Date: Wed, 27 Sep 2017 14:28:56 +0530 [thread overview]
Message-ID: <1506502753-27408-1-git-send-email-mgautam@codeaurora.org> (raw)
QUSB-v2 and QMP-v3 USB PHYs are present on Qualcomm's 14nm
and 10nm SOCs.
This patch series adds support for runtime PM for these
USB PHYs and adds fixes in drivers to follow PHY reset and
initialization sequence as per hardware programming manual.
Changes since v1:
- Incorporated review comments.
- Fixes to align with hardware programming manual.
- Added support for QUSBv2 and QMPv3 PHYs.
- Enable DP/DM asynchronous interrupts from QUSB2 USB2 PHY
for remote-wakeup.
- Enable LFPS and RX-TERM detection for attach and detach
events from QMP USB3 PHY for remotewakeup.
- Update sw-vbus overide in PHY wrapper for device mode.
- Dropped one dwc3 patch from this series which I will submit
with other dwc3 patches. ("usb: dwc3: core: Notify USB3 PHY as
well for DRD modes")
Manu Gautam (15):
phy: qcom-qmp: Power-on PHY before initialization
phy: qcom-qusb2: Power-on PHY before initialization
phy: qcom-qmp: Fix PHY block reset sequence
phy: qcom-qmp: Move SERDES/PCS START after PHY reset
phy: qcom-qusb2: Add support for different register layouts
dt-bindings: phy-qcom-qusb2: Update binding for QUSB2 V2 version
phy: qcom-qusb2: Add support for QUSB2 V2 version
phy: qcom-qmp: Move register offsets to header file
phy: qcom-qmp: Add register offsets for QMP V3 PHY
dt-bindings: phy-qcom-qmp: Update bindings for QMP V3 USB PHY
phy: qcom-qmp: Add support for QMP V3 USB3 PHY
phy: qcom-qusb2: Set vbus sw-override signal in device mode
phy: qcom-qusb2: Add support for runtime PM
phy: qcom-qmp: Override lane0_power_present signal in device mode
phy: qcom-qmp: Add support for runtime PM
Vivek Gautam (2):
phy: qcom-qmp: Fix phy pipe clock gating
phy: qcom-qmp: Adapt to clk_bulk_* APIs
.../devicetree/bindings/phy/qcom-qmp-phy.txt | 6 +-
.../devicetree/bindings/phy/qcom-qusb2-phy.txt | 5 +-
drivers/phy/qualcomm/phy-qcom-qmp.c | 696 +++++++++++++++------
drivers/phy/qualcomm/phy-qcom-qmp.h | 289 +++++++++
drivers/phy/qualcomm/phy-qcom-qusb2.c | 412 ++++++++++--
5 files changed, 1148 insertions(+), 260 deletions(-)
create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp.h
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
next reply other threads:[~2017-09-27 8:59 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-09-27 8:58 Manu Gautam [this message]
2017-09-27 8:58 ` [PATCH v2 01/17] phy: qcom-qmp: Fix phy pipe clock gating Manu Gautam
2017-09-27 8:58 ` [PATCH v2 02/17] phy: qcom-qmp: Adapt to clk_bulk_* APIs Manu Gautam
2017-09-27 8:58 ` [PATCH v2 03/17] phy: qcom-qmp: Power-on PHY before initialization Manu Gautam
2017-09-27 8:59 ` [PATCH v2 04/17] phy: qcom-qusb2: " Manu Gautam
2017-09-27 8:59 ` [PATCH v2 05/17] phy: qcom-qmp: Fix PHY block reset sequence Manu Gautam
2017-09-27 8:59 ` [PATCH v2 06/17] phy: qcom-qmp: Move SERDES/PCS START after PHY reset Manu Gautam
2017-09-27 8:59 ` [PATCH v2 07/17] phy: qcom-qusb2: Add support for different register layouts Manu Gautam
2017-09-27 8:59 ` [PATCH v2 08/17] dt-bindings: phy-qcom-qusb2: Update binding for QUSB2 V2 version Manu Gautam
2017-10-05 22:10 ` Rob Herring
2017-09-27 8:59 ` [PATCH v2 09/17] phy: qcom-qusb2: Add support " Manu Gautam
2017-09-27 8:59 ` [PATCH v2 10/17] phy: qcom-qmp: Move register offsets to header file Manu Gautam
2017-09-27 8:59 ` [PATCH v2 11/17] phy: qcom-qmp: Add register offsets for QMP V3 PHY Manu Gautam
2017-09-27 8:59 ` [PATCH v2 12/17] dt-bindings: phy-qcom-qmp: Update bindings for QMP V3 USB PHY Manu Gautam
2017-10-05 22:14 ` Rob Herring
2017-09-27 8:59 ` [PATCH v2 13/17] phy: qcom-qmp: Add support for QMP V3 USB3 PHY Manu Gautam
2017-09-27 17:59 ` Jack Pham
2017-10-05 6:30 ` Manu Gautam
2017-09-27 8:59 ` [PATCH v2 14/17] phy: qcom-qusb2: Set vbus sw-override signal in device mode Manu Gautam
2017-09-27 17:57 ` Jack Pham
2017-09-27 19:16 ` Jack Pham
2017-09-28 4:00 ` Manu Gautam
2017-09-28 16:53 ` Jack Pham
2017-10-05 9:08 ` Manu Gautam
2017-10-09 8:03 ` Manu Gautam
2017-10-23 10:49 ` Manu Gautam
2017-09-27 8:59 ` [PATCH v2 15/17] phy: qcom-qusb2: Add support for runtime PM Manu Gautam
2017-09-27 8:59 ` [PATCH v2 16/17] phy: qcom-qmp: Override lane0_power_present signal in device mode Manu Gautam
2017-09-27 8:59 ` [PATCH v2 17/17] phy: qcom-qmp: Add support for runtime PM Manu Gautam
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1506502753-27408-1-git-send-email-mgautam@codeaurora.org \
--to=mgautam@codeaurora.org \
--cc=balbi@kernel.org \
--cc=kishon@ti.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).