From: Manu Gautam <mgautam@codeaurora.org>
To: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <balbi@kernel.org>,
linux-arm-msm@vger.kernel.org, linux-usb@vger.kernel.org,
Manu Gautam <mgautam@codeaurora.org>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Stephen Boyd <sboyd@codeaurora.org>,
Vivek Gautam <vivek.gautam@codeaurora.org>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@vger.kernel.org>,
open list <linux-kernel@vger.kernel.org>
Subject: [PATCH v2 08/17] dt-bindings: phy-qcom-qusb2: Update binding for QUSB2 V2 version
Date: Wed, 27 Sep 2017 14:29:04 +0530 [thread overview]
Message-ID: <1506502753-27408-9-git-send-email-mgautam@codeaurora.org> (raw)
In-Reply-To: <1506502753-27408-1-git-send-email-mgautam@codeaurora.org>
Update generic compatible string for QUSB2 V2 PHY. This will allow
all targets using QUSB2 V2 use same string.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
---
Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
index aa0fcb0..42c9742 100644
--- a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
+++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
@@ -4,7 +4,10 @@ Qualcomm QUSB2 phy controller
QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets.
Required properties:
- - compatible: compatible list, contains "qcom,msm8996-qusb2-phy".
+ - compatible: compatible list, contains
+ "qcom,msm8996-qusb2-phy" for 14nm PHY on msm8996,
+ "qcom,qusb2-v2-phy" for QUSB2 V2 PHY.
+
- reg: offset and length of the PHY register set.
- #phy-cells: must be 0.
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
next prev parent reply other threads:[~2017-09-27 8:59 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-09-27 8:58 [PATCH v2 00/17] Support for Qualcomm QUSBv2 and QMPv3 USB PHYs Manu Gautam
2017-09-27 8:58 ` [PATCH v2 01/17] phy: qcom-qmp: Fix phy pipe clock gating Manu Gautam
2017-09-27 8:58 ` [PATCH v2 02/17] phy: qcom-qmp: Adapt to clk_bulk_* APIs Manu Gautam
2017-09-27 8:58 ` [PATCH v2 03/17] phy: qcom-qmp: Power-on PHY before initialization Manu Gautam
2017-09-27 8:59 ` [PATCH v2 04/17] phy: qcom-qusb2: " Manu Gautam
2017-09-27 8:59 ` [PATCH v2 05/17] phy: qcom-qmp: Fix PHY block reset sequence Manu Gautam
2017-09-27 8:59 ` [PATCH v2 06/17] phy: qcom-qmp: Move SERDES/PCS START after PHY reset Manu Gautam
2017-09-27 8:59 ` [PATCH v2 07/17] phy: qcom-qusb2: Add support for different register layouts Manu Gautam
2017-09-27 8:59 ` Manu Gautam [this message]
2017-10-05 22:10 ` [PATCH v2 08/17] dt-bindings: phy-qcom-qusb2: Update binding for QUSB2 V2 version Rob Herring
2017-09-27 8:59 ` [PATCH v2 09/17] phy: qcom-qusb2: Add support " Manu Gautam
2017-09-27 8:59 ` [PATCH v2 10/17] phy: qcom-qmp: Move register offsets to header file Manu Gautam
2017-09-27 8:59 ` [PATCH v2 11/17] phy: qcom-qmp: Add register offsets for QMP V3 PHY Manu Gautam
2017-09-27 8:59 ` [PATCH v2 12/17] dt-bindings: phy-qcom-qmp: Update bindings for QMP V3 USB PHY Manu Gautam
2017-10-05 22:14 ` Rob Herring
2017-09-27 8:59 ` [PATCH v2 13/17] phy: qcom-qmp: Add support for QMP V3 USB3 PHY Manu Gautam
2017-09-27 17:59 ` Jack Pham
2017-10-05 6:30 ` Manu Gautam
2017-09-27 8:59 ` [PATCH v2 14/17] phy: qcom-qusb2: Set vbus sw-override signal in device mode Manu Gautam
2017-09-27 17:57 ` Jack Pham
2017-09-27 19:16 ` Jack Pham
2017-09-28 4:00 ` Manu Gautam
2017-09-28 16:53 ` Jack Pham
2017-10-05 9:08 ` Manu Gautam
2017-10-09 8:03 ` Manu Gautam
2017-10-23 10:49 ` Manu Gautam
2017-09-27 8:59 ` [PATCH v2 15/17] phy: qcom-qusb2: Add support for runtime PM Manu Gautam
2017-09-27 8:59 ` [PATCH v2 16/17] phy: qcom-qmp: Override lane0_power_present signal in device mode Manu Gautam
2017-09-27 8:59 ` [PATCH v2 17/17] phy: qcom-qmp: Add support for runtime PM Manu Gautam
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1506502753-27408-9-git-send-email-mgautam@codeaurora.org \
--to=mgautam@codeaurora.org \
--cc=balbi@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=kishon@ti.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=sboyd@codeaurora.org \
--cc=vivek.gautam@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).