From: Manu Gautam <mgautam@codeaurora.org>
To: Kishon Vijay Abraham I <kishon@ti.com>
Cc: linux-arm-msm@vger.kernel.org, linux-usb@vger.kernel.org,
Manu Gautam <mgautam@codeaurora.org>,
Vivek Gautam <vivek.gautam@codeaurora.org>,
Varadarajan Narayanan <varada@codeaurora.org>,
smuthayy <smuthayy@codeaurora.org>,
Wei Yongjun <weiyongjun1@huawei.com>,
Fengguang Wu <fengguang.wu@intel.com>,
"open list:GENERIC PHY FRAMEWORK" <linux-kernel@vger.kernel.org>
Subject: [PATCH v3 03/16] phy: qcom-qmp: Power-on PHY before initialization
Date: Tue, 21 Nov 2017 14:53:13 +0530 [thread overview]
Message-ID: <1511256206-1587-4-git-send-email-mgautam@codeaurora.org> (raw)
In-Reply-To: <1511256206-1587-1-git-send-email-mgautam@codeaurora.org>
PHY must be powered on before turning ON clocks and
attempting to initialize it. Driver is exposing
separate init and power_on routines for this.
Apparently USB dwc3 core driver performs power-on after
init. Also, poweron and init for QMP PHY need to be
executed together always, hence remove poweron callback
from phy_ops and explicitly perform this from com_init,
similar changes needed for poweroff. On similar lines move
clk_enable from init to com_init which can be called once
for multi lane PHYs.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
---
drivers/phy/qualcomm/phy-qcom-qmp.c | 61 +++++++++++++------------------------
1 file changed, 21 insertions(+), 40 deletions(-)
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index 90794dd..2f427e3 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -720,33 +720,6 @@ static void qcom_qmp_phy_configure(void __iomem *base,
}
}
-static int qcom_qmp_phy_poweron(struct phy *phy)
-{
- struct qmp_phy *qphy = phy_get_drvdata(phy);
- struct qcom_qmp *qmp = qphy->qmp;
- int num = qmp->cfg->num_vregs;
- int ret;
-
- dev_vdbg(&phy->dev, "Powering on QMP phy\n");
-
- /* turn on regulator supplies */
- ret = regulator_bulk_enable(num, qmp->vregs);
- if (ret)
- dev_err(qmp->dev, "failed to enable regulators, err=%d\n", ret);
-
- return ret;
-}
-
-static int qcom_qmp_phy_poweroff(struct phy *phy)
-{
- struct qmp_phy *qphy = phy_get_drvdata(phy);
- struct qcom_qmp *qmp = qphy->qmp;
-
- regulator_bulk_disable(qmp->cfg->num_vregs, qmp->vregs);
-
- return 0;
-}
-
static int qcom_qmp_phy_com_init(struct qcom_qmp *qmp)
{
const struct qmp_phy_cfg *cfg = qmp->cfg;
@@ -759,6 +732,19 @@ static int qcom_qmp_phy_com_init(struct qcom_qmp *qmp)
return 0;
}
+ /* turn on regulator supplies */
+ ret = regulator_bulk_enable(cfg->num_vregs, qmp->vregs);
+ if (ret) {
+ mutex_unlock(&qmp->phy_mutex);
+ return ret;
+ }
+
+ ret = clk_bulk_prepare_enable(cfg->num_clks, qmp->clks);
+ if (ret) {
+ dev_err(qmp->dev, "failed to enable clks, err=%d\n", ret);
+ goto err_clk_enable;
+ }
+
for (i = 0; i < cfg->num_resets; i++) {
ret = reset_control_deassert(qmp->resets[i]);
if (ret) {
@@ -803,6 +789,9 @@ static int qcom_qmp_phy_com_init(struct qcom_qmp *qmp)
err_rst:
while (--i >= 0)
reset_control_assert(qmp->resets[i]);
+ clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks);
+err_clk_enable:
+ regulator_bulk_disable(cfg->num_vregs, qmp->vregs);
mutex_unlock(&qmp->phy_mutex);
return ret;
@@ -832,6 +821,10 @@ static int qcom_qmp_phy_com_exit(struct qcom_qmp *qmp)
while (--i >= 0)
reset_control_assert(qmp->resets[i]);
+ clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks);
+
+ regulator_bulk_disable(cfg->num_vregs, qmp->vregs);
+
mutex_unlock(&qmp->phy_mutex);
return 0;
@@ -852,15 +845,9 @@ static int qcom_qmp_phy_init(struct phy *phy)
dev_vdbg(qmp->dev, "Initializing QMP phy\n");
- ret = clk_bulk_prepare_enable(cfg->num_clks, qmp->clks);
- if (ret) {
- dev_err(qmp->dev, "failed to enable clks, err=%d\n", ret);
- return ret;
- }
-
ret = qcom_qmp_phy_com_init(qmp);
if (ret)
- goto err_com_init;
+ return ret;
if (cfg->has_lane_rst) {
ret = reset_control_deassert(qphy->lane_rst);
@@ -915,8 +902,6 @@ static int qcom_qmp_phy_init(struct phy *phy)
reset_control_assert(qphy->lane_rst);
err_lane_rst:
qcom_qmp_phy_com_exit(qmp);
-err_com_init:
- clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks);
return ret;
}
@@ -943,8 +928,6 @@ static int qcom_qmp_phy_exit(struct phy *phy)
qcom_qmp_phy_com_exit(qmp);
- clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks);
-
return 0;
}
@@ -1057,8 +1040,6 @@ static int phy_pipe_clk_register(struct qcom_qmp *qmp, struct device_node *np)
static const struct phy_ops qcom_qmp_phy_gen_ops = {
.init = qcom_qmp_phy_init,
.exit = qcom_qmp_phy_exit,
- .power_on = qcom_qmp_phy_poweron,
- .power_off = qcom_qmp_phy_poweroff,
.owner = THIS_MODULE,
};
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
next prev parent reply other threads:[~2017-11-21 9:23 UTC|newest]
Thread overview: 35+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-11-21 9:23 [PATCH v3 00/16] Support for Qualcomm QUSBv2 and QMPv3 USB PHYs Manu Gautam
2017-11-21 9:23 ` [PATCH v3 01/16] phy: qcom-qmp: Fix phy pipe clock gating Manu Gautam
2017-11-21 9:23 ` [PATCH v3 02/16] phy: qcom-qmp: Adapt to clk_bulk_* APIs Manu Gautam
2017-12-20 2:37 ` Vivek Gautam
[not found] ` <CAFp+6iEgiv0KJo+ikR_jyakc2dGjetiArJSvC4d5JFO0ZnO7-Q-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2017-12-20 5:03 ` Manu Gautam
2017-11-21 9:23 ` Manu Gautam [this message]
2017-11-22 18:03 ` [PATCH v3 03/16] phy: qcom-qmp: Power-on PHY before initialization Stephen Boyd
2017-11-23 3:59 ` Manu Gautam
2017-11-21 9:23 ` [PATCH v3 04/16] phy: qcom-qusb2: " Manu Gautam
2017-11-21 9:23 ` [PATCH v3 05/16] phy: qcom-qmp: Fix PHY block reset sequence Manu Gautam
2017-11-21 9:23 ` [PATCH v3 06/16] phy: qcom-qmp: Move SERDES/PCS START after PHY reset Manu Gautam
2017-11-21 9:23 ` [PATCH v3 07/16] phy: qcom-qusb2: Add support for different register layouts Manu Gautam
2017-12-05 10:23 ` Vivek Gautam
[not found] ` <3c0dca03-bf9e-8747-8c31-546172f88d6f-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2017-12-12 8:51 ` Manu Gautam
2017-11-21 9:23 ` [PATCH v3 08/16] dt-bindings: phy-qcom-qusb2: Update binding for QUSB2 V2 version Manu Gautam
2017-11-21 9:23 ` [PATCH v3 09/16] phy: qcom-qusb2: Add support " Manu Gautam
2017-11-21 9:23 ` [PATCH v3 10/16] phy: qcom-qmp: Move register offsets to header file Manu Gautam
2017-11-22 17:26 ` Stephen Boyd
2017-11-23 4:02 ` Manu Gautam
2017-11-21 9:23 ` [PATCH v3 11/16] phy: qcom-qmp: Add register offsets for QMP V3 PHY Manu Gautam
2017-11-21 9:23 ` [PATCH v3 12/16] dt-bindings: phy-qcom-qmp: Update bindings for QMP V3 USB PHY Manu Gautam
2017-11-21 9:23 ` [PATCH v3 13/16] phy: qcom-qmp: Add support for QMP V3 USB3 PHY Manu Gautam
2017-11-21 9:23 ` [PATCH v3 14/16] phy: Add notify_speed callback Manu Gautam
2017-12-12 11:43 ` Kishon Vijay Abraham I
2017-12-12 15:24 ` Manu Gautam
2017-12-20 5:49 ` Kishon Vijay Abraham I
2017-12-20 6:29 ` Manu Gautam
2017-12-20 7:17 ` Kishon Vijay Abraham I
2017-12-20 8:41 ` Manu Gautam
2017-12-28 11:04 ` Kishon Vijay Abraham I
2017-12-29 4:24 ` Manu Gautam
2017-12-29 6:28 ` Kishon Vijay Abraham I
2018-01-02 5:42 ` Manu Gautam
2017-11-21 9:23 ` [PATCH v3 15/16] phy: qcom-qusb2: Add support for runtime PM Manu Gautam
2017-11-21 9:23 ` [PATCH v3 16/16] phy: qcom-qmp: " Manu Gautam
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1511256206-1587-4-git-send-email-mgautam@codeaurora.org \
--to=mgautam@codeaurora.org \
--cc=fengguang.wu@intel.com \
--cc=kishon@ti.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=smuthayy@codeaurora.org \
--cc=varada@codeaurora.org \
--cc=vivek.gautam@codeaurora.org \
--cc=weiyongjun1@huawei.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).