From: Manu Gautam <mgautam@codeaurora.org>
To: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <balbi@kernel.org>,
linux-arm-msm@vger.kernel.org, linux-usb@vger.kernel.org,
Manu Gautam <mgautam@codeaurora.org>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Vivek Gautam <vivek.gautam@codeaurora.org>,
Stephen Boyd <sboyd@codeaurora.org>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@vger.kernel.org>,
open list <linux-kernel@vger.kernel.org>
Subject: [PATCH v4 08/16] dt-bindings: phy-qcom-qusb2: Update binding for QUSB2 V2 version
Date: Wed, 3 Jan 2018 16:58:41 +0530 [thread overview]
Message-ID: <1514978930-31341-9-git-send-email-mgautam@codeaurora.org> (raw)
In-Reply-To: <1514978930-31341-1-git-send-email-mgautam@codeaurora.org>
Update generic compatible string for QUSB2 V2 PHY. This will allow
all targets using QUSB2 V2 use same string.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
---
Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
index aa0fcb0..42c9742 100644
--- a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
+++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
@@ -4,7 +4,10 @@ Qualcomm QUSB2 phy controller
QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets.
Required properties:
- - compatible: compatible list, contains "qcom,msm8996-qusb2-phy".
+ - compatible: compatible list, contains
+ "qcom,msm8996-qusb2-phy" for 14nm PHY on msm8996,
+ "qcom,qusb2-v2-phy" for QUSB2 V2 PHY.
+
- reg: offset and length of the PHY register set.
- #phy-cells: must be 0.
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
next prev parent reply other threads:[~2018-01-03 11:28 UTC|newest]
Thread overview: 27+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-01-03 11:28 [PATCH v4 00/16] Support for Qualcomm QUSBv2 and QMPv3 USB PHYs Manu Gautam
2018-01-03 11:28 ` [PATCH v4 01/16] phy: qcom-qmp: Fix phy pipe clock gating Manu Gautam
2018-01-03 11:28 ` [PATCH v4 02/16] phy: qcom-qmp: Adapt to clk_bulk_* APIs Manu Gautam
2018-01-03 11:28 ` [PATCH v4 03/16] phy: qcom-qmp: Power-on PHY before initialization Manu Gautam
[not found] ` <1514978930-31341-4-git-send-email-mgautam-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2018-01-12 8:27 ` Vivek Gautam
2018-01-03 11:28 ` [PATCH v4 04/16] phy: qcom-qusb2: " Manu Gautam
[not found] ` <1514978930-31341-5-git-send-email-mgautam-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2018-01-12 8:29 ` Vivek Gautam
2018-01-03 11:28 ` [PATCH v4 05/16] phy: qcom-qmp: Fix PHY block reset sequence Manu Gautam
2018-01-12 8:44 ` Vivek Gautam
2018-01-12 8:46 ` Manu Gautam
2018-01-12 9:12 ` Vivek Gautam
2018-01-03 11:28 ` [PATCH v4 06/16] phy: qcom-qmp: Move SERDES/PCS START after PHY reset Manu Gautam
2018-01-03 11:28 ` [PATCH v4 07/16] phy: qcom-qusb2: Add support for different register layouts Manu Gautam
2018-01-12 9:18 ` Vivek Gautam
2018-01-03 11:28 ` Manu Gautam [this message]
2018-01-03 11:28 ` [PATCH v4 09/16] phy: qcom-qusb2: Add support for QUSB2 V2 version Manu Gautam
2018-01-12 9:29 ` Vivek Gautam
2018-01-03 11:28 ` [PATCH v4 10/16] phy: qcom-qmp: Move register offsets to header file Manu Gautam
2018-01-12 6:26 ` Vivek Gautam
2018-01-03 11:28 ` [PATCH v4 11/16] phy: qcom-qmp: Add register offsets for QMP V3 PHY Manu Gautam
2018-01-03 11:28 ` [PATCH v4 12/16] dt-bindings: phy-qcom-qmp: Update bindings for QMP V3 USB PHY Manu Gautam
2018-01-03 11:28 ` [PATCH v4 13/16] phy: qcom-qmp: Add support for QMP V3 USB3 PHY Manu Gautam
2018-01-03 11:28 ` [PATCH v4 14/16] phy: Add USB speed related PHY modes Manu Gautam
2018-01-05 11:01 ` Kishon Vijay Abraham I
2018-01-08 4:46 ` Manu Gautam
2018-01-03 11:28 ` [PATCH v4 15/16] phy: qcom-qusb2: Add support for runtime PM Manu Gautam
2018-01-03 11:28 ` [PATCH v4 16/16] phy: qcom-qmp: " Manu Gautam
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1514978930-31341-9-git-send-email-mgautam@codeaurora.org \
--to=mgautam@codeaurora.org \
--cc=balbi@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=kishon@ti.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=sboyd@codeaurora.org \
--cc=vivek.gautam@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox