From: Sivaprakash Murugesan <sivaprak@codeaurora.org>
To: agross@kernel.org, bjorn.andersson@linaro.org, kishon@ti.com,
robh+dt@kernel.org, linux-arm-msm@vger.kernel.org,
linux-kernel@vger.kernel.org, devicetree@vger.kernel.org
Cc: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Subject: [PATCH V2 5/5] arm64: dts: ipq8074: enable USB support
Date: Sat, 11 Apr 2020 10:32:32 +0530 [thread overview]
Message-ID: <1586581352-27017-6-git-send-email-sivaprak@codeaurora.org> (raw)
In-Reply-To: <1586581352-27017-1-git-send-email-sivaprak@codeaurora.org>
IPQ8074 has two super speed usb ports, add phy and dwc3 nodes
to enable them.
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
---
[V2]
* Addressed Bjorn's review comments
arch/arm64/boot/dts/qcom/ipq8074-hk01.dts | 24 +++++
arch/arm64/boot/dts/qcom/ipq8074.dtsi | 167 ++++++++++++++++++++++++++++++
2 files changed, 191 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts b/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
index 6754cb0..dadaa8e 100644
--- a/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
+++ b/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
@@ -82,3 +82,27 @@
nand-bus-width = <8>;
};
};
+
+&qusb_phy_0 {
+ status = "ok";
+};
+
+&qusb_phy_1 {
+ status = "ok";
+};
+
+&ssphy_0 {
+ status = "ok";
+};
+
+&ssphy_1 {
+ status = "ok";
+};
+
+&usb_0 {
+ status = "ok";
+};
+
+&usb_1 {
+ status = "ok";
+};
diff --git a/arch/arm64/boot/dts/qcom/ipq8074.dtsi b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
index 5303821..506a8ac 100644
--- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
@@ -82,6 +82,91 @@
ranges = <0 0 0 0xffffffff>;
compatible = "simple-bus";
+ ssphy_1: phy@58000 {
+ compatible = "qcom,ipq8074-qmp-usb3-phy";
+ reg = <0x00058000 0x1c4>;
+ #clock-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ clocks = <&gcc GCC_USB1_AUX_CLK>,
+ <&gcc GCC_USB1_PHY_CFG_AHB_CLK>,
+ <&xo>;
+ clock-names = "aux", "cfg_ahb", "ref";
+
+ resets = <&gcc GCC_USB1_PHY_BCR>,
+ <&gcc GCC_USB3PHY_1_PHY_BCR>;
+ reset-names = "phy","common";
+ status = "disabled";
+
+ usb1_ssphy: lane@58200 {
+ reg = <0x00058200 0x130>, /* Tx */
+ <0x00058400 0x200>, /* Rx */
+ <0x00058800 0x1f8>, /* PCS */
+ <0x00058600 0x044>; /* PCS misc*/
+ #phy-cells = <0>;
+ clocks = <&gcc GCC_USB1_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "gcc_usb1_pipe_clk_src";
+ };
+ };
+
+ qusb_phy_1: phy@59000 {
+ compatible = "qcom,ipq8074-qusb2-phy";
+ reg = <0x00059000 0x180>;
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_USB1_PHY_CFG_AHB_CLK>,
+ <&xo>;
+ clock-names = "cfg_ahb", "ref";
+
+ resets = <&gcc GCC_QUSB2_1_PHY_BCR>;
+ status = "disabled";
+ };
+
+ ssphy_0: phy@78000 {
+ compatible = "qcom,ipq8074-qmp-usb3-phy";
+ reg = <0x00078000 0x1c4>;
+ #clock-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ clocks = <&gcc GCC_USB0_AUX_CLK>,
+ <&gcc GCC_USB0_PHY_CFG_AHB_CLK>,
+ <&xo>;
+ clock-names = "aux", "cfg_ahb", "ref";
+
+ resets = <&gcc GCC_USB0_PHY_BCR>,
+ <&gcc GCC_USB3PHY_0_PHY_BCR>;
+ reset-names = "phy","common";
+ status = "disabled";
+
+ usb0_ssphy: lane@78200 {
+ reg = <0x00078200 0x130>, /* Tx */
+ <0x00078400 0x200>, /* Rx */
+ <0x00078800 0x1f8>, /* PCS */
+ <0x00078600 0x044>; /* PCS misc*/
+ #phy-cells = <0>;
+ clocks = <&gcc GCC_USB0_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "gcc_usb0_pipe_clk_src";
+ };
+ };
+
+ qusb_phy_0: phy@79000 {
+ compatible = "qcom,ipq8074-qusb2-phy";
+ reg = <0x00079000 0x180>;
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>,
+ <&xo>;
+ clock-names = "cfg_ahb", "ref";
+
+ resets = <&gcc GCC_QUSB2_0_PHY_BCR>;
+ };
+
pcie_phy0: phy@86000 {
compatible = "qcom,ipq8074-qmp-pcie-phy";
reg = <0x00086000 0x1000>;
@@ -294,6 +379,88 @@
status = "disabled";
};
+ usb_0: usb@8af8800 {
+ compatible = "qcom,dwc3";
+ reg = <0x08af8800 0x400>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>,
+ <&gcc GCC_USB0_MASTER_CLK>,
+ <&gcc GCC_USB0_SLEEP_CLK>,
+ <&gcc GCC_USB0_MOCK_UTMI_CLK>;
+ clock-names = "sys_noc_axi",
+ "master",
+ "sleep",
+ "mock_utmi";
+
+ assigned-clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>,
+ <&gcc GCC_USB0_MASTER_CLK>,
+ <&gcc GCC_USB0_MOCK_UTMI_CLK>;
+ assigned-clock-rates = <133330000>,
+ <133330000>,
+ <19200000>;
+
+ resets = <&gcc GCC_USB0_BCR>;
+ status = "disabled";
+
+ dwc_0: dwc3@8a00000 {
+ compatible = "snps,dwc3";
+ reg = <0x8a00000 0xcd00>;
+ interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&qusb_phy_0>, <&usb0_ssphy>;
+ phy-names = "usb2-phy", "usb3-phy";
+ tx-fifo-resize;
+ snps,is-utmi-l1-suspend;
+ snps,hird-threshold = /bits/ 8 <0x0>;
+ snps,dis_u2_susphy_quirk;
+ snps,dis_u3_susphy_quirk;
+ dr_mode = "host";
+ };
+ };
+
+ usb_1: usb@8cf8800 {
+ compatible = "qcom,dwc3";
+ reg = <0x08cf8800 0x400>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ clocks = <&gcc GCC_SYS_NOC_USB1_AXI_CLK>,
+ <&gcc GCC_USB1_MASTER_CLK>,
+ <&gcc GCC_USB1_SLEEP_CLK>,
+ <&gcc GCC_USB1_MOCK_UTMI_CLK>;
+ clock-names = "sys_noc_axi",
+ "master",
+ "sleep",
+ "mock_utmi";
+
+ assigned-clocks = <&gcc GCC_SYS_NOC_USB1_AXI_CLK>,
+ <&gcc GCC_USB1_MASTER_CLK>,
+ <&gcc GCC_USB1_MOCK_UTMI_CLK>;
+ assigned-clock-rates = <133330000>,
+ <133330000>,
+ <19200000>;
+
+ resets = <&gcc GCC_USB1_BCR>;
+ status = "disabled";
+
+ dwc_1: dwc3@8c00000 {
+ compatible = "snps,dwc3";
+ reg = <0x8c00000 0xcd00>;
+ interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&qusb_phy_1>, <&usb1_ssphy>;
+ phy-names = "usb2-phy", "usb3-phy";
+ tx-fifo-resize;
+ snps,is-utmi-l1-suspend;
+ snps,hird-threshold = /bits/ 8 <0x0>;
+ snps,dis_u2_susphy_quirk;
+ snps,dis_u3_susphy_quirk;
+ dr_mode = "host";
+ };
+ };
+
intc: interrupt-controller@b000000 {
compatible = "qcom,msm-qgic2";
interrupt-controller;
--
2.7.4
prev parent reply other threads:[~2020-04-11 5:03 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-04-11 5:02 [PATCH V2 0/5] Enable USB support in IPQ8074 Sivaprakash Murugesan
2020-04-11 5:02 ` [PATCH V2 1/5] dt-bindings: phy: qcom,qmp: Add ipq8074 usb dt bindings Sivaprakash Murugesan
2020-04-20 18:45 ` Rob Herring
2020-04-11 5:02 ` [PATCH V2 2/5] dt-bindings: phy: qcom,qusb2: Add ipq8074 device compatible Sivaprakash Murugesan
2020-04-20 18:46 ` Rob Herring
2020-04-11 5:02 ` [PATCH V2 3/5] phy: qcom-qmp: Add USB QMP PHY support for IPQ8074 Sivaprakash Murugesan
2020-04-11 5:02 ` [PATCH V2 4/5] phy: qcom-qusb2: Add ipq8074 device compatible Sivaprakash Murugesan
2020-04-11 5:02 ` Sivaprakash Murugesan [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1586581352-27017-6-git-send-email-sivaprak@codeaurora.org \
--to=sivaprak@codeaurora.org \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=kishon@ti.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).