linux-arm-msm.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Loic Poulain <loic.poulain@linaro.org>
To: manivannan.sadhasivam@linaro.org, hemantk@codeaurora.org
Cc: linux-arm-msm@vger.kernel.org, jhugo@codeaurora.org,
	bbhatt@codeaurora.org, Loic Poulain <loic.poulain@linaro.org>
Subject: [PATCH v4 05/10] mhi: pci_generic: Add support for reset
Date: Thu, 10 Dec 2020 11:02:50 +0100	[thread overview]
Message-ID: <1607594575-31590-6-git-send-email-loic.poulain@linaro.org> (raw)
In-Reply-To: <1607594575-31590-1-git-send-email-loic.poulain@linaro.org>

Add support for resetting the device, reset can be triggered in case
of error or manually via sysfs (/sys/bus/pci/devices/*/reset).

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
---
 drivers/bus/mhi/pci_generic.c | 120 +++++++++++++++++++++++++++++++++++++-----
 1 file changed, 107 insertions(+), 13 deletions(-)

diff --git a/drivers/bus/mhi/pci_generic.c b/drivers/bus/mhi/pci_generic.c
index 077595c..d70d3ea 100644
--- a/drivers/bus/mhi/pci_generic.c
+++ b/drivers/bus/mhi/pci_generic.c
@@ -8,6 +8,7 @@
  * Copyright (C) 2020 Linaro Ltd <loic.poulain@linaro.org>
  */
 
+#include <linux/delay.h>
 #include <linux/device.h>
 #include <linux/mhi.h>
 #include <linux/module.h>
@@ -177,6 +178,16 @@ static const struct pci_device_id mhi_pci_id_table[] = {
 };
 MODULE_DEVICE_TABLE(pci, mhi_pci_id_table);
 
+enum mhi_pci_device_status {
+	MHI_PCI_DEV_STARTED,
+};
+
+struct mhi_pci_device {
+	struct mhi_controller mhi_cntrl;
+	struct pci_saved_state *pci_state;
+	unsigned long status;
+};
+
 static int mhi_pci_read_reg(struct mhi_controller *mhi_cntrl,
 			    void __iomem *addr, u32 *out)
 {
@@ -196,6 +207,20 @@ static void mhi_pci_status_cb(struct mhi_controller *mhi_cntrl,
 	/* Nothing to do for now */
 }
 
+static bool mhi_pci_is_alive(struct mhi_controller *mhi_cntrl)
+{
+	struct pci_dev *pdev = to_pci_dev(mhi_cntrl->cntrl_dev);
+	u16 vendor = 0;
+
+	if (pci_read_config_word(pdev, PCI_VENDOR_ID, &vendor))
+		return false;
+
+	if (vendor == (u16) ~0 || vendor == 0)
+		return false;
+
+	return true;
+}
+
 static int mhi_pci_claim(struct mhi_controller *mhi_cntrl,
 			 unsigned int bar_num, u64 dma_mask)
 {
@@ -291,16 +316,20 @@ static int mhi_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 {
 	const struct mhi_pci_dev_info *info = (struct mhi_pci_dev_info *) id->driver_data;
 	const struct mhi_controller_config *mhi_cntrl_config;
+	struct mhi_pci_device *mhi_pdev;
 	struct mhi_controller *mhi_cntrl;
 	int err;
 
 	dev_dbg(&pdev->dev, "MHI PCI device found: %s\n", info->name);
 
-	mhi_cntrl = mhi_alloc_controller();
-	if (!mhi_cntrl)
+	mhi_pdev = devm_kzalloc(&pdev->dev, sizeof(*mhi_pdev), GFP_KERNEL);
+	if (!mhi_pdev)
 		return -ENOMEM;
 
 	mhi_cntrl_config = info->config;
+	mhi_cntrl = &mhi_pdev->mhi_cntrl;
+
+	mhi_initialize_controller(mhi_cntrl);
 	mhi_cntrl->cntrl_dev = &pdev->dev;
 	mhi_cntrl->iova_start = 0;
 	mhi_cntrl->iova_stop = DMA_BIT_MASK(info->dma_data_width);
@@ -315,17 +344,21 @@ static int mhi_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 
 	err = mhi_pci_claim(mhi_cntrl, info->bar_num, DMA_BIT_MASK(info->dma_data_width));
 	if (err)
-		goto err_release;
+		return err;
 
 	err = mhi_pci_get_irqs(mhi_cntrl, mhi_cntrl_config);
 	if (err)
-		goto err_release;
+		return err;
+
+	pci_set_drvdata(pdev, mhi_pdev);
 
-	pci_set_drvdata(pdev, mhi_cntrl);
+	/* Have stored pci confspace at hand for restore in sudden PCI error */
+	pci_save_state(pdev);
+	mhi_pdev->pci_state = pci_store_saved_state(pdev);
 
 	err = mhi_register_controller(mhi_cntrl, mhi_cntrl_config);
 	if (err)
-		goto err_release;
+		return err;
 
 	/* MHI bus does not power up the controller by default */
 	err = mhi_prepare_for_power_up(mhi_cntrl);
@@ -340,33 +373,94 @@ static int mhi_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 		goto err_unprepare;
 	}
 
+	set_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status);
+
 	return 0;
 
 err_unprepare:
 	mhi_unprepare_after_power_down(mhi_cntrl);
 err_unregister:
 	mhi_unregister_controller(mhi_cntrl);
-err_release:
-	mhi_free_controller(mhi_cntrl);
 
 	return err;
 }
 
 static void mhi_pci_remove(struct pci_dev *pdev)
 {
-	struct mhi_controller *mhi_cntrl = pci_get_drvdata(pdev);
+	struct mhi_pci_device *mhi_pdev = pci_get_drvdata(pdev);
+	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
+
+	if (test_and_clear_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status)) {
+		mhi_power_down(mhi_cntrl, true);
+		mhi_unprepare_after_power_down(mhi_cntrl);
+	}
 
-	mhi_power_down(mhi_cntrl, true);
-	mhi_unprepare_after_power_down(mhi_cntrl);
 	mhi_unregister_controller(mhi_cntrl);
-	mhi_free_controller(mhi_cntrl);
 }
 
+void mhi_pci_reset_prepare(struct pci_dev *pdev)
+{
+	struct mhi_pci_device *mhi_pdev = pci_get_drvdata(pdev);
+	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
+
+	dev_info(&pdev->dev, "reset\n");
+
+	/* Clean up MHI state */
+	if (test_and_clear_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status)) {
+		mhi_power_down(mhi_cntrl, false);
+		mhi_unprepare_after_power_down(mhi_cntrl);
+	}
+
+	/* cause internal device reset */
+	mhi_reg_soc_reset(mhi_cntrl);
+
+	/* Be sure device reset has been executed */
+	msleep(500);
+}
+
+void mhi_pci_reset_done(struct pci_dev *pdev)
+{
+	struct mhi_pci_device *mhi_pdev = pci_get_drvdata(pdev);
+	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
+	int err;
+
+	/* Restore initial known working PCI state */
+	pci_load_saved_state(pdev, mhi_pdev->pci_state);
+	pci_restore_state(pdev);
+
+	/* Is device status available ? */
+	if (!mhi_pci_is_alive(mhi_cntrl)) {
+		dev_err(&pdev->dev, "reset failed\n");
+		return;
+	}
+
+	err = mhi_prepare_for_power_up(mhi_cntrl);
+	if (err) {
+		dev_err(&pdev->dev, "failed to prepare MHI controller\n");
+		return;
+	}
+
+	err = mhi_sync_power_up(mhi_cntrl);
+	if (err) {
+		dev_err(&pdev->dev, "failed to power up MHI controller\n");
+		mhi_unprepare_after_power_down(mhi_cntrl);
+		return;
+	}
+
+	set_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status);
+}
+
+static const struct pci_error_handlers mhi_pci_err_handler = {
+	.reset_prepare = mhi_pci_reset_prepare,
+	.reset_done = mhi_pci_reset_done,
+};
+
 static struct pci_driver mhi_pci_driver = {
 	.name		= "mhi-pci-generic",
 	.id_table	= mhi_pci_id_table,
 	.probe		= mhi_pci_probe,
-	.remove		= mhi_pci_remove
+	.remove		= mhi_pci_remove,
+	.err_handler	= &mhi_pci_err_handler,
 };
 module_pci_driver(mhi_pci_driver);
 
-- 
2.7.4


  parent reply	other threads:[~2020-12-10  9:57 UTC|newest]

Thread overview: 20+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-12-10 10:02 [PATCH v4 00/10] mhi: pci_generic: Misc improvements Loic Poulain
2020-12-10 10:02 ` [PATCH v4 01/10] mhi: Add mhi_controller_initialize helper Loic Poulain
2020-12-11 18:57   ` Hemant Kumar
     [not found]     ` <CAMZdPi8+UFmTOeivvZXefm-UHuN+v5zNJBQuZAOw0omiWY-ifw@mail.gmail.com>
2020-12-11 20:00       ` Hemant Kumar
2020-12-14 14:01         ` Loic Poulain
2020-12-10 10:02 ` [PATCH v4 02/10] bus: mhi: core: Add device hardware reset support Loic Poulain
2020-12-10 10:02 ` [PATCH v4 03/10] mhi: pci-generic: Increase number of hardware events Loic Poulain
2020-12-10 10:02 ` [PATCH v4 04/10] mhi: pci_generic: Enable burst mode for hardware channels Loic Poulain
2020-12-10 10:02 ` Loic Poulain [this message]
2020-12-11 20:15   ` [PATCH v4 05/10] mhi: pci_generic: Add support for reset Hemant Kumar
2020-12-14 14:04     ` Loic Poulain
2020-12-10 10:02 ` [PATCH v4 06/10] mhi: pci_generic: Add suspend/resume/recovery procedure Loic Poulain
2020-12-11 20:22   ` Hemant Kumar
2020-12-14 14:06     ` Loic Poulain
2020-12-10 10:02 ` [PATCH v4 07/10] mhi: pci_generic: Add PCI error handlers Loic Poulain
2020-12-11 20:25   ` Hemant Kumar
2020-12-10 10:02 ` [PATCH v4 08/10] mhi: pci_generic: Add health-check Loic Poulain
2020-12-10 10:02 ` [PATCH v4 09/10] mhi: pci_generic: Increase controller timeout value Loic Poulain
2020-12-10 10:02 ` [PATCH v4 10/10] mhi: pci_generic: Add diag channels Loic Poulain
2020-12-11 20:28   ` Hemant Kumar

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1607594575-31590-6-git-send-email-loic.poulain@linaro.org \
    --to=loic.poulain@linaro.org \
    --cc=bbhatt@codeaurora.org \
    --cc=hemantk@codeaurora.org \
    --cc=jhugo@codeaurora.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=manivannan.sadhasivam@linaro.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).