Re: [PATCH v2 3/4] dt-bindings: phy: Add support for QMP phy

[Stephen Boyd <sboyd-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>]

On 11/22, Vivek Gautam wrote:
> diff --git a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
> new file mode 100644
> index 0000000..ffb173b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
> @@ -0,0 +1,74 @@
> +Qualcomm QMP PHY
> +----------------
> +
> +QMP phy controller supports physical layer functionality for a number of
> +controllers on Qualcomm chipsets, such as, PCIe, UFS, and USB.
> +
> +Required properties:
> + - compatible: compatible list, contains:
> +	       "qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996,
> +	       "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996.
> + - reg: list of offset and length pair of the PHY register sets.
> +	at index 0: offset and length of register set for PHY common
> +		    serdes block.
> +	from index 1 - N: offset and length of register set for each lane,
> +			  for N number of phy lanes (ports).
> + - lane-offsets: array of offsets to tx, rx and pcs blocks for phy lanes.
> + - #phy-cells: must be 1
> +    - Cell after phy phandle should be the port (lane) number.
> + - clocks: a list of phandles and clock-specifier pairs,
> +	   one for each entry in clock-names.
> + - clock-names: must be "cfg_ahb" for phy config clock,
> +			"aux" for phy aux clock,
> +			"ref_clk" for 19.2 MHz ref clk,
> +			"ref_clk_src" for reference clock source,

We typically leave "clk" out of clk names because it's redundant.

> +			"pipe<port-number>" for pipe clock specific to
> +			each port/lane (Optional).

The pipe clocks are orphaned right now. We should add an output
clock from the phy to go into the controller and back into the
phy if I recall correctly. The phy should be a clock provider
itself so it can output the pipe clock source into GCC and back
into the phy and controller.

> + - resets: a list of phandles and reset controller specifier pairs,
> +	   one for each entry in reset-names.
> + - reset-names: must be "phy" for reset of phy block,
> +			"common" for phy common block reset,
> +			"cfg" for phy's ahb cfg block reset (Optional).
> +			"port<port-number>" for reset specific to
> +			each port/lane (Optional).
> + - vdda-phy-supply: Phandle to a regulator supply to PHY core block.
> + - vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block.
> +
> +Optional properties:
> + - vddp-ref-clk-supply: Phandle to a regulator supply to any specific refclk
> +			pll block.
> +
> +Example:
> +	pcie_phy: pciephy@34000 {

pcie-phy or just phy as the node name?

-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html