[PATCH v5 13/13] arm64: dts: sc7180: Add qupv3_0 and qupv3_1

Rajendra Nayak
2019-11-08T09:29:49Z

From: Roja Rani Yarubandi <rojay@codeaurora.org>

Add QUP SE instances configuration for sc7180.

Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
---
arch/arm64/boot/dts/qcom/sc7180-idp.dts | 146 +++++
arch/arm64/boot/dts/qcom/sc7180.dtsi | 675 ++++++++++++++++++++++++
2 files changed, 821 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
index d8206d1b5896..189254f5ae95 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
@@ -17,6 +17,7 @@
compatible = "qcom,sc7180-idp";

aliases {
+ hsuart0 = &uart3;
serial0 = &uart8;
};

@@ -231,16 +232,100 @@
};
};

+&qupv3_id_0 {
+ status = "okay";
+};
+
&qupv3_id_1 {
status = "okay";
};

+&uart3 {
+ status = "okay";
+};
+
&uart8 {
status = "okay";
};

/* PINCTRL - additions to nodes defined in sc7180.dtsi */

+&qup_i2c2_default {
+ pinconf {
+ pins = "gpio15", "gpio16";
+ drive-strength = <2>;
+
+ /* Has external pullup */
+ bias-disable;
+ };
+};
+
+&qup_i2c4_default {
+ pinconf {
+ pins = "gpio115", "gpio116";
+ drive-strength = <2>;
+
+ /* Has external pullup */
+ bias-disable;
+ };
+};
+
+&qup_i2c7_default {
+ pinconf {
+ pins = "gpio6", "gpio7";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
+
+&qup_i2c9_default {
+ pinconf {
+ pins = "gpio46", "gpio47";
+ drive-strength = <2>;
+
+ /* Has external pullup */
+ bias-disable;
+ };
+};
+
+&qup_uart3_default {
+ pinconf-cts {
+ /*
+ * Configure a pull-down on 38 (CTS) to match the pull of
+ * the Bluetooth module.
+ */
+ pins = "gpio38";
+ bias-pull-down;
+ output-high;
+ };
+
+ pinconf-rts {
+ /* We'll drive 39 (RTS), so no pull */
+ pins = "gpio39";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ pinconf-tx {
+ /* We'll drive 40 (TX), so no pull */
+ pins = "gpio40";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+
+ pinconf-rx {
+ /*
+ * Configure a pull-up on 41 (RX). This is needed to avoid
+ * garbage data when the TX pin of the Bluetooth module is
+ * in tri-state (module powered off or not driving the
+ * signal yet).
+ */
+ pins = "gpio41";
+ bias-pull-up;
+ };
+};
+
&qup_uart8_default {
pinconf-tx {
pins = "gpio44";
@@ -254,3 +339,64 @@
bias-pull-up;
};
};
+
+&qup_spi0_default {
+ pinconf {
+ pins = "gpio34", "gpio35", "gpio36", "gpio37";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
+
+&qup_spi6_default {
+ pinconf {
+ pins = "gpio59", "gpio60", "gpio61", "gpio62";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
+
+&qup_spi10_default {
+ pinconf {
+ pins = "gpio86", "gpio87", "gpio88", "gpio89";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
+
+&qspi {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qspi_clk &qspi_cs0 &qspi_data01>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+ spi-tx-bus-width = <2>;
+ spi-rx-bus-width = <2>;
+ };
+};
+
+&qspi_cs0 {
+ pinconf {
+ pins = "gpio68";
+ bias-disable;
+ };
+};
+
+&qspi_clk {
+ pinconf {
+ pins = "gpio63";
+ bias-disable;
+ };
+};
+
+&qspi_data01 {
+ pinconf {
+ pins = "gpio64", "gpio65";
+
+ /* High-Z when no transfers; nice to park the lines */
+ bias-pull-up;
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
index e1d6278d85f7..666e9b92c7ad 100644
--- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
@@ -182,6 +182,214 @@
#power-domain-cells = <1>;
};

+ qupv3_id_0: geniqup@8c0000 {
+ compatible = "qcom,geni-se-qup";
+ reg = <0 0x008c0000 0 0x6000>;
+ clock-names = "m-ahb", "s-ahb";
+ clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
+ <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ i2c0: i2c@880000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00880000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c0_default>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi0: spi@880000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00880000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi0_default>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart0: serial@880000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00880000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart0_default>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@884000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00884000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c1_default>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi1: spi@884000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00884000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi1_default>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart1: serial@884000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00884000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart1_default>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@888000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00888000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c2_default>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart2: serial@888000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00888000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart2_default>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@88c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x0088c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c3_default>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi3: spi@88c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x0088c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi3_default>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart3: serial@88c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x0088c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart3_default>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ i2c4: i2c@890000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00890000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c4_default>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart4: serial@890000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00890000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart4_default>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ i2c5: i2c@894000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00894000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c5_default>;
+ interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi5: spi@894000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00894000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi5_default>;
+ interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart5: serial@894000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00894000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart5_default>;
+ interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+ };
+
qupv3_id_1: geniqup@ac0000 {
compatible = "qcom,geni-se-qup";
reg = <0 0x00ac0000 0 0x6000>;
@@ -193,6 +401,93 @@
ranges;
status = "disabled";

+ i2c6: i2c@a80000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a80000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c6_default>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi6: spi@a80000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a80000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi6_default>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart6: serial@a80000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a80000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart6_default>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ i2c7: i2c@a84000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a84000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c7_default>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart7: serial@a84000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a84000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart7_default>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ i2c8: i2c@a88000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a88000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c8_default>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi8: spi@a88000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a88000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi8_default>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
uart8: serial@a88000 {
compatible = "qcom,geni-debug-uart";
reg = <0 0x00a88000 0 0x4000>;
@@ -203,6 +498,104 @@
interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
+
+ i2c9: i2c@a8c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a8c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c9_default>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart9: serial@a8c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a8c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart9_default>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ i2c10: i2c@a90000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a90000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c10_default>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi10: spi@a90000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a90000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi10_default>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart10: serial@a90000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a90000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart10_default>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ i2c11: i2c@a94000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a94000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c11_default>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi11: spi@a94000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a94000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi11_default>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart11: serial@a94000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a94000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart11_default>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
};

pdc: interrupt-controller@b220000 {
@@ -228,12 +621,294 @@
#interrupt-cells = <2>;
gpio-ranges = <&tlmm 0 0 120>;

+ qspi_clk: qspi-clk {
+ pinmux {
+ pins = "gpio63";
+ function = "qspi_clk";
+ };
+ };
+
+ qspi_cs0: qspi-cs0 {
+ pinmux {
+ pins = "gpio68";
+ function = "qspi_cs";
+ };
+ };
+
+ qspi_cs1: qspi-cs1 {
+ pinmux {
+ pins = "gpio72";
+ function = "qspi_cs";
+ };
+ };
+
+ qspi_data01: qspi-data01 {
+ pinmux-data {
+ pins = "gpio64", "gpio65";
+ function = "qspi_data";
+ };
+ };
+
+ qspi_data12: qspi-data12 {
+ pinmux-data {
+ pins = "gpio66", "gpio67";
+ function = "qspi_data";
+ };
+ };
+
+ qup_i2c0_default: qup-i2c0-default {
+ pinmux {
+ pins = "gpio34", "gpio35";
+ function = "qup00";
+ };
+ };
+
+ qup_i2c1_default: qup-i2c1-default {
+ pinmux {
+ pins = "gpio0", "gpio1";
+ function = "qup01";
+ };
+ };
+
+ qup_i2c2_default: qup-i2c2-default {
+ pinmux {
+ pins = "gpio15", "gpio16";
+ function = "qup02";
+ };
+ };
+
+ qup_i2c3_default: qup-i2c3-default {
+ pinmux {
+ pins = "gpio38", "gpio39";
+ function = "qup03";
+ };
+ };
+
+ qup_i2c4_default: qup-i2c4-default {
+ pinmux {
+ pins = "gpio115", "gpio116";
+ function = "qup04";
+ };
+ };
+
+ qup_i2c5_default: qup-i2c5-default {
+ pinmux {
+ pins = "gpio25", "gpio26";
+ function = "qup05";
+ };
+ };
+
+ qup_i2c6_default: qup-i2c6-default {
+ pinmux {
+ pins = "gpio59", "gpio60";
+ function = "qup10";
+ };
+ };
+
+ qup_i2c7_default: qup-i2c7-default {
+ pinmux {
+ pins = "gpio6", "gpio7";
+ function = "qup11";
+ };
+ };
+
+ qup_i2c8_default: qup-i2c8-default {
+ pinmux {
+ pins = "gpio42", "gpio43";
+ function = "qup12";
+ };
+ };
+
+ qup_i2c9_default: qup-i2c9-default {
+ pinmux {
+ pins = "gpio46", "gpio47";
+ function = "qup13";
+ };
+ };
+
+ qup_i2c10_default: qup-i2c10-default {
+ pinmux {
+ pins = "gpio86", "gpio87";
+ function = "qup14";
+ };
+ };
+
+ qup_i2c11_default: qup-i2c11-default {
+ pinmux {
+ pins = "gpio53", "gpio54";
+ function = "qup15";
+ };
+ };
+
+ qup_spi0_default: qup-spi0-default {
+ pinmux {
+ pins = "gpio34", "gpio35",
+ "gpio36", "gpio37";
+ function = "qup00";
+ };
+ };
+
+ qup_spi1_default: qup-spi1-default {
+ pinmux {
+ pins = "gpio0", "gpio1",
+ "gpio2", "gpio3",
+ "gpio12", "gpio94";
+ function = "qup01";
+ };
+ };
+
+ qup_spi3_default: qup-spi3-default {
+ pinmux {
+ pins = "gpio38", "gpio39",
+ "gpio40", "gpio41";
+ function = "qup03";
+ };
+ };
+
+ qup_spi5_default: qup-spi5-default {
+ pinmux {
+ pins = "gpio25", "gpio26",
+ "gpio27", "gpio28";
+ function = "qup05";
+ };
+ };
+
+ qup_spi6_default: qup-spi6-default {
+ pinmux {
+ pins = "gpio59", "gpio60",
+ "gpio61", "gpio62",
+ "gpio68", "gpio72";
+ function = "qup10";
+ };
+ };
+
+ qup_spi8_default: qup-spi8-default {
+ pinmux {
+ pins = "gpio42", "gpio43",
+ "gpio44", "gpio45";
+ function = "qup12";
+ };
+ };
+
+ qup_spi10_default: qup-spi10-default {
+ pinmux {
+ pins = "gpio86", "gpio87",
+ "gpio88", "gpio89",
+ "gpio90", "gpio91";
+ function = "qup14";
+ };
+ };
+
+ qup_spi11_default: qup-spi11-default {
+ pinmux {
+ pins = "gpio53", "gpio54",
+ "gpio55", "gpio56";
+ function = "qup15";
+ };
+ };
+
+ qup_uart0_default: qup-uart0-default {
+ pinmux {
+ pins = "gpio34", "gpio35",
+ "gpio36", "gpio37";
+ function = "qup00";
+ };
+ };
+
+ qup_uart1_default: qup-uart1-default {
+ pinmux {
+ pins = "gpio0", "gpio1",
+ "gpio2", "gpio3";
+ function = "qup01";
+ };
+ };
+
+ qup_uart2_default: qup-uart2-default {
+ pinmux {
+ pins = "gpio15", "gpio16";
+ function = "qup02";
+ };
+ };
+
+ qup_uart3_default: qup-uart3-default {
+ pinmux {
+ pins = "gpio38", "gpio39",
+ "gpio40", "gpio41";
+ function = "qup03";
+ };
+ };
+
+ qup_uart4_default: qup-uart4-default {
+ pinmux {
+ pins = "gpio115", "gpio116";
+ function = "qup04";
+ };
+ };
+
+ qup_uart5_default: qup-uart5-default {
+ pinmux {
+ pins = "gpio25", "gpio26",
+ "gpio27", "gpio28";
+ function = "qup05";
+ };
+ };
+
+ qup_uart6_default: qup-uart6-default {
+ pinmux {
+ pins = "gpio59", "gpio60",
+ "gpio61", "gpio62";
+ function = "qup10";
+ };
+ };
+
+ qup_uart7_default: qup-uart7-default {
+ pinmux {
+ pins = "gpio6", "gpio7";
+ function = "qup11";
+ };
+ };
+
qup_uart8_default: qup-uart8-default {
pinmux {
pins = "gpio44", "gpio45";
function = "qup12";
};
};
+
+ qup_uart9_default: qup-uart9-default {
+ pinmux {
+ pins = "gpio46", "gpio47";
+ function = "qup13";
+ };
+ };
+
+ qup_uart10_default: qup-uart10-default {
+ pinmux {
+ pins = "gpio86", "gpio87",
+ "gpio88", "gpio89";
+ function = "qup14";
+ };
+ };
+
+ qup_uart11_default: qup-uart11-default {
+ pinmux {
+ pins = "gpio53", "gpio54",
+ "gpio55", "gpio56";
+ function = "qup15";
+ };
+ };
+ };
+
+ qspi: spi@88dc000 {
+ compatible = "qcom,qspi-v1";
+ reg = <0 0x088dc000 0 0x600>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+ <&gcc GCC_QSPI_CORE_CLK>;
+ clock-names = "iface", "core";
+ status = "disabled";
};

spmi_bus: spmi@c440000 {