From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Cc: agross@kernel.org, kishon@ti.com, robh+dt@kernel.org,
linux-arm-msm@vger.kernel.org, linux-kernel@vger.kernel.org,
devicetree@vger.kernel.org,
Balaji Prakash J <bjagadee@codeaurora.org>
Subject: Re: [PATCH 3/3] arm64: dts: ipq8074: enable USB support
Date: Fri, 10 Apr 2020 15:17:48 -0700 [thread overview]
Message-ID: <20200410221748.GD20625@builder.lan> (raw)
In-Reply-To: <1586543372-13969-4-git-send-email-sivaprak@codeaurora.org>
On Fri 10 Apr 11:29 PDT 2020, Sivaprakash Murugesan wrote:
> IPQ8074 has two super speed usb ports, add phy and dwc3 nodes
> to enable them.
>
Thanks Sivaprakash, your patch looks good, just some comments on the
style below.
> Co-developed-by: Balaji Prakash J <bjagadee@codeaurora.org>
> Signed-off-by: Balaji Prakash J <bjagadee@codeaurora.org>
> Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
> ---
> arch/arm64/boot/dts/qcom/ipq8074-hk01.dts | 24 +++++
> arch/arm64/boot/dts/qcom/ipq8074.dtsi | 168 ++++++++++++++++++++++++++++++
> 2 files changed, 192 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts b/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
> index 70be3f9..dd27d84 100644
> --- a/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
> +++ b/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
> @@ -26,6 +26,22 @@
> };
>
> soc {
> + ssphy@58000 {
Please reference these by label, like we do in e.g. sdm845-mtp.dts.
> + status = "ok";
> + };
> +
> + qusb@59000 {
> + status = "ok";
> + };
> +
> + ssphy@78000 {
> + status = "ok";
> + };
> +
> + qusb@79000 {
> + status = "ok";
> + };
> +
> serial@78b3000 {
> status = "ok";
> };
> @@ -65,6 +81,14 @@
> };
> };
>
> + usb3@8A00000 {
> + status = "ok";
> + };
> +
> + usb3@8C00000 {
> + status = "ok";
> + };
> +
> phy@86000 {
> status = "ok";
> };
> diff --git a/arch/arm64/boot/dts/qcom/ipq8074.dtsi b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
> index 2b31823..47bb9ad 100644
> --- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
> +++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
> @@ -16,6 +16,92 @@
> ranges = <0 0 0 0xffffffff>;
> compatible = "simple-bus";
>
> + ssphy_1: ssphy@58000 {
Please use the generic name of "phy" here (i.e. ssphy_1: phy@58000 {)
> + compatible = "qcom,ipq8074-qmp-usb3-phy";
> + reg = <0x00058000 0x1c4>;
> + status = "disabled";
> + #clock-cells = <1>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + clocks = <&gcc GCC_USB1_AUX_CLK>,
> + <&gcc GCC_USB1_PHY_CFG_AHB_CLK>,
> + <&xo>;
> + clock-names = "aux", "cfg_ahb", "ref";
> +
> + resets = <&gcc GCC_USB1_PHY_BCR>,
> + <&gcc GCC_USB3PHY_1_PHY_BCR>;
> + reset-names = "phy","common";
> +
> + usb1_ssphy: lane@58200 {
> + reg = <0x00058200 0x130>, /* Tx */
> + <0x00058400 0x200>, /* Rx */
> + <0x00058800 0x1F8>, /* PCS */
> + <0x00058600 0x044>; /* PCS misc */
> + #phy-cells = <0>;
> + clocks = <&gcc GCC_USB1_PIPE_CLK>;
> + clock-names = "pipe0";
> + clock-output-names = "gcc_usb1_pipe_clk_src";
> + };
> + };
> +
> + qusb_phy_1: qusb@59000 {
phy@
> + compatible = "qcom,msm8996-qusb2-phy";
Please add and use a ipq8074 compatible to the driver (.data can point
to msm8996_phy_cfg still).
> + reg = <0x00059000 0x180>;
> + status = "disabled";
> + #phy-cells = <0>;
> +
> + clocks = <&gcc GCC_USB1_PHY_CFG_AHB_CLK>,
> + <&xo>;
> + clock-names = "cfg_ahb", "ref";
> +
> + resets = <&gcc GCC_QUSB2_1_PHY_BCR>;
> + };
> +
> + ssphy_0: ssphy@78000 {
phy@
> + compatible = "qcom,ipq8074-qmp-usb3-phy";
> + reg = <0x00078000 0x1c4>;
> + status = "disabled";
> + #clock-cells = <1>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + clocks = <&gcc GCC_USB0_AUX_CLK>,
> + <&gcc GCC_USB0_PHY_CFG_AHB_CLK>,
> + <&xo>;
> + clock-names = "aux", "cfg_ahb", "ref";
> +
> + resets = <&gcc GCC_USB0_PHY_BCR>,
> + <&gcc GCC_USB3PHY_0_PHY_BCR>;
> + reset-names = "phy","common";
> +
> + usb0_ssphy: lane@78200 {
> + reg = <0x00078200 0x130>, /* Tx */
> + <0x00078400 0x200>, /* Rx */
> + <0x00078800 0x1F8>, /* PCS */
> + <0x00078600 0x044>; /* PCS misc */
> + #phy-cells = <0>;
> + clocks = <&gcc GCC_USB0_PIPE_CLK>;
> + clock-names = "pipe0";
> + clock-output-names = "gcc_usb0_pipe_clk_src";
> + };
> + };
> +
> + qusb_phy_0: qusb@79000 {
phy@
> + compatible = "qcom,msm8996-qusb2-phy";
> + reg = <0x00079000 0x180>;
> + status = "disabled";
> + #phy-cells = <0>;
> +
> + clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>,
> + <&xo>;
> + clock-names = "cfg_ahb", "ref";
> +
> + resets = <&gcc GCC_QUSB2_0_PHY_BCR>;
> + };
> +
> tlmm: pinctrl@1000000 {
> compatible = "qcom,ipq8074-pinctrl";
> reg = <0x1000000 0x300000>;
> @@ -272,6 +358,88 @@
> status = "disabled";
> };
>
> + usb3_0: usb3@8A00000 {
usb@ and please lower case and make sure the unit address matches the
reg.
> + compatible = "qcom,dwc3";
> + reg = <0x08af8800 0x400>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>,
> + <&gcc GCC_USB0_MASTER_CLK>,
> + <&gcc GCC_USB0_SLEEP_CLK>,
> + <&gcc GCC_USB0_MOCK_UTMI_CLK>;
> + clock-names = "sys_noc_axi",
> + "master",
> + "sleep",
> + "mock_utmi";
> +
> + assigned-clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>,
> + <&gcc GCC_USB0_MASTER_CLK>,
> + <&gcc GCC_USB0_MOCK_UTMI_CLK>;
> + assigned-clock-rates = <133330000>,
> + <133330000>,
> + <19200000>;
> +
> + resets = <&gcc GCC_USB0_BCR>;
> + status = "disabled";
> +
> + dwc_0: dwc3@8A00000 {
Please lowercase the address
> + compatible = "snps,dwc3";
> + reg = <0x8A00000 0xcd00>;
Ditto.
> + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
> + phys = <&qusb_phy_0>, <&usb0_ssphy>;
> + phy-names = "usb2-phy", "usb3-phy";
> + tx-fifo-resize;
> + snps,is-utmi-l1-suspend;
> + snps,hird-threshold = /bits/ 8 <0x0>;
> + snps,dis_u2_susphy_quirk;
> + snps,dis_u3_susphy_quirk;
> + dr_mode = "host";
> + };
> + };
> +
> + usb3_1: usb3@8C00000 {
usb@, lowercase and match reg.
> + compatible = "qcom,dwc3";
> + reg = <0x08cf8800 0x400>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + clocks = <&gcc GCC_SYS_NOC_USB1_AXI_CLK>,
> + <&gcc GCC_USB1_MASTER_CLK>,
> + <&gcc GCC_USB1_SLEEP_CLK>,
> + <&gcc GCC_USB1_MOCK_UTMI_CLK>;
> + clock-names = "sys_noc_axi",
> + "master",
> + "sleep",
> + "mock_utmi";
> +
> + assigned-clocks = <&gcc GCC_SYS_NOC_USB1_AXI_CLK>,
> + <&gcc GCC_USB1_MASTER_CLK>,
> + <&gcc GCC_USB1_MOCK_UTMI_CLK>;
> + assigned-clock-rates = <133330000>,
> + <133330000>,
> + <19200000>;
> +
> + resets = <&gcc GCC_USB1_BCR>;
> + status = "disabled";
> +
> + dwc_1: dwc3@8C00000 {
Please lowercase
> + compatible = "snps,dwc3";
> + reg = <0x8C00000 0xcd00>;
Ditto.
> + interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
> + phys = <&qusb_phy_1>, <&usb1_ssphy>;
> + phy-names = "usb2-phy", "usb3-phy";
> + tx-fifo-resize;
> + snps,is-utmi-l1-suspend;
> + snps,hird-threshold = /bits/ 8 <0x0>;
> + snps,dis_u2_susphy_quirk;
> + snps,dis_u3_susphy_quirk;
> + dr_mode = "host";
> + };
> + };
> +
> pcie_phy0: phy@86000 {
> compatible = "qcom,ipq8074-qmp-pcie-phy";
> reg = <0x86000 0x1000>;
If you could send a separate patch (after this is merged is okay) that
sort the nodes in this file by address, it would be much appreciated.
Regards,
Bjorn
> --
> 2.7.4
>
next prev parent reply other threads:[~2020-04-10 22:17 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-04-10 18:29 [PATCH 0/3] Enable USB support in IPQ8074 Sivaprakash Murugesan
2020-04-10 18:29 ` [PATCH 1/3] dt-bindings: phy: qcom,qmp: Add ipq8074 usb dt bindings Sivaprakash Murugesan
2020-04-10 22:05 ` Bjorn Andersson
2020-04-11 0:45 ` Sivaprakash Murugesan
2020-04-10 18:29 ` [PATCH 2/3] phy: qcom-qmp: Add USB QMP PHY support for IPQ8074 Sivaprakash Murugesan
2020-04-10 22:18 ` Bjorn Andersson
2020-04-10 18:29 ` [PATCH 3/3] arm64: dts: ipq8074: enable USB support Sivaprakash Murugesan
2020-04-10 22:17 ` Bjorn Andersson [this message]
2020-04-11 0:54 ` Sivaprakash Murugesan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200410221748.GD20625@builder.lan \
--to=bjorn.andersson@linaro.org \
--cc=agross@kernel.org \
--cc=bjagadee@codeaurora.org \
--cc=devicetree@vger.kernel.org \
--cc=kishon@ti.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=sivaprak@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).