From: Vinod Koul <vkoul@kernel.org>
To: Wesley Cheng <wcheng@codeaurora.org>
Cc: kishon@ti.com, agross@kernel.org, bjorn.andersson@linaro.org,
linux-arm-msm@vger.kernel.org, linux-kernel@vger.kernel.org,
jackp@codeaurora.org
Subject: Re: [PATCH v3 1/2] phy: qcom-snps: Add runtime suspend and resume handlers
Date: Mon, 29 Jun 2020 15:14:21 +0530 [thread overview]
Message-ID: <20200629094421.GD2599@vkoul-mobl> (raw)
In-Reply-To: <20200625195444.15130-2-wcheng@codeaurora.org>
Hi Wesley,
On 25-06-20, 12:54, Wesley Cheng wrote:
> Allow for the PHY to be put into a powered down state when possible.
> Add the required suspend and resume callbacks, which will determine
> what resources can be turned off depending on the cable status.
>
> Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
> Reviewed-by: Vinod Koul <vkoul@kernel.org>
Please do not add this tag unless someone send it explictly over the
email.. I do not recall sending a review tag
> ---
> drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c | 73 +++++++++++++++++++
> 1 file changed, 73 insertions(+)
>
> diff --git a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
> index 4d74045271eb..152d8633f4ea 100644
> --- a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
> +++ b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
> @@ -104,6 +104,63 @@ static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset,
> readl_relaxed(base + offset);
> }
>
> +static int qcom_snps_hsphy_suspend(struct qcom_snps_hsphy *hsphy)
> +{
> + dev_dbg(&hsphy->phy->dev, "Suspend QCOM SNPS PHY\n");
> +
> + if (hsphy->mode == PHY_MODE_USB_HOST) {
> + /* Enable auto-resume to meet remote wakeup timing */
> + qcom_snps_hsphy_write_mask(hsphy->base,
> + USB2_PHY_USB_PHY_HS_PHY_CTRL2,
> + USB2_AUTO_RESUME,
> + USB2_AUTO_RESUME);
> + usleep_range(500, 1000);
> + qcom_snps_hsphy_write_mask(hsphy->base,
> + USB2_PHY_USB_PHY_HS_PHY_CTRL2,
> + 0, USB2_AUTO_RESUME);
> + }
> +
> + clk_disable_unprepare(hsphy->cfg_ahb_clk);
> + return 0;
> +}
> +
> +static int qcom_snps_hsphy_resume(struct qcom_snps_hsphy *hsphy)
> +{
> + int ret;
> +
> + dev_dbg(&hsphy->phy->dev, "Resume QCOM SNPS PHY, mode\n");
> +
> + ret = clk_prepare_enable(hsphy->cfg_ahb_clk);
> + if (ret) {
> + dev_err(&hsphy->phy->dev, "failed to enable cfg ahb clock\n");
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int __maybe_unused qcom_snps_hsphy_runtime_suspend(struct device *dev)
> +{
> + struct qcom_snps_hsphy *hsphy = dev_get_drvdata(dev);
> +
> + if (!hsphy->phy_initialized)
> + return 0;
> +
> + qcom_snps_hsphy_suspend(hsphy);
> + return 0;
> +}
> +
> +static int __maybe_unused qcom_snps_hsphy_runtime_resume(struct device *dev)
> +{
> + struct qcom_snps_hsphy *hsphy = dev_get_drvdata(dev);
> +
> + if (!hsphy->phy_initialized)
> + return 0;
> +
> + qcom_snps_hsphy_resume(hsphy);
> + return 0;
> +}
> +
> static int qcom_snps_hsphy_init(struct phy *phy)
> {
> struct qcom_snps_hsphy *hsphy = phy_get_drvdata(phy);
> @@ -212,6 +269,11 @@ static const struct of_device_id qcom_snps_hsphy_of_match_table[] = {
> };
> MODULE_DEVICE_TABLE(of, qcom_snps_hsphy_of_match_table);
>
> +static const struct dev_pm_ops qcom_snps_hsphy_pm_ops = {
> + SET_RUNTIME_PM_OPS(qcom_snps_hsphy_runtime_suspend,
> + qcom_snps_hsphy_runtime_resume, NULL)
> +};
> +
> static int qcom_snps_hsphy_probe(struct platform_device *pdev)
> {
> struct device *dev = &pdev->dev;
> @@ -255,6 +317,14 @@ static int qcom_snps_hsphy_probe(struct platform_device *pdev)
> return ret;
> }
>
> + pm_runtime_set_active(dev);
> + pm_runtime_enable(dev);
> + /*
> + * Prevent runtime pm from being ON by default. Users can enable
> + * it using power/control in sysfs.
> + */
> + pm_runtime_forbid(dev);
> +
> generic_phy = devm_phy_create(dev, NULL, &qcom_snps_hsphy_gen_ops);
> if (IS_ERR(generic_phy)) {
> ret = PTR_ERR(generic_phy);
> @@ -269,6 +339,8 @@ static int qcom_snps_hsphy_probe(struct platform_device *pdev)
> phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> if (!IS_ERR(phy_provider))
> dev_dbg(dev, "Registered Qcom-SNPS HS phy\n");
> + else
> + pm_runtime_disable(dev);
>
> return PTR_ERR_OR_ZERO(phy_provider);
> }
> @@ -277,6 +349,7 @@ static struct platform_driver qcom_snps_hsphy_driver = {
> .probe = qcom_snps_hsphy_probe,
> .driver = {
> .name = "qcom-snps-hs-femto-v2-phy",
> + .pm = &qcom_snps_hsphy_pm_ops,
> .of_match_table = qcom_snps_hsphy_of_match_table,
> },
> };
> --
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
--
~Vinod
next prev parent reply other threads:[~2020-06-29 21:30 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-06-25 19:54 [PATCH v3 0/2] phy: qcom-snps: Add runtime suspend and resume handlers Wesley Cheng
2020-06-25 19:54 ` [PATCH v3 1/2] " Wesley Cheng
2020-06-29 9:44 ` Vinod Koul [this message]
2020-06-25 19:54 ` [PATCH v3 2/2] phy: qcom-snps: Add a set mode callback Wesley Cheng
2020-06-29 9:46 ` [PATCH v3 0/2] phy: qcom-snps: Add runtime suspend and resume handlers Vinod Koul
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200629094421.GD2599@vkoul-mobl \
--to=vkoul@kernel.org \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=jackp@codeaurora.org \
--cc=kishon@ti.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=wcheng@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox