[PATCH v2 0/7[ arm64: add support for display on qrb5165-rb5

[PATCH v2 0/7[ arm64: add support for display on qrb5165-rb5

[Dmitry Baryshkov]

This patch series adds support for display device nodes on qrb5165-rb5
board using lt9611uxc DSI-HDMI bridge.

Changes since v1:
 - Move zap firmware to qcom/sm8250/
 - Use squshed firmware (mbn) instead of mdt

[PATCH v2 1/7] arm64: dts: qcom: sm8250.dtsi: add display system nodes

[Dmitry Baryshkov]

Add device tree nodes for mdss, mdp, dsi0/1.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8250.dtsi | 302 ++++++++++++++++++++++++++-
 1 file changed, 295 insertions(+), 7 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
index 65acd1f381eb..f4cae2b82e2a 100644
--- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -4,10 +4,12 @@
  */
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,dispcc-sm8250.h>
 #include <dt-bindings/clock/qcom,gcc-sm8250.h>
 #include <dt-bindings/clock/qcom,gpucc-sm8250.h>
 #include <dt-bindings/clock/qcom,rpmh.h>
 #include <dt-bindings/interconnect/qcom,osm-l3.h>
+#include <dt-bindings/interconnect/qcom,sm8250.h>
 #include <dt-bindings/mailbox/qcom-ipcc.h>
 #include <dt-bindings/power/qcom-aoss-qmp.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
@@ -1254,14 +1256,8 @@ tcsr_mutex: hwlock@1f40000 {
 		};
 
 		gpu: gpu@3d00000 {
-			/*
-			 * note: the amd,imageon compatible makes it possible
-			 * to use the drm/msm driver without the display node,
-			 * make sure to remove it when display node is added
-			 */
 			compatible = "qcom,adreno-650.2",
-				     "qcom,adreno",
-				     "amd,imageon";
+				     "qcom,adreno";
 			#stream-id-cells = <16>;
 
 			reg = <0 0x03d00000 0 0x40000>;
@@ -1803,6 +1799,298 @@ usb_2_dwc3: dwc3@a800000 {
 			};
 		};
 
+		mdss: mdss@ae00000 {
+			compatible = "qcom,sdm845-mdss";
+			reg = <0 0x0ae00000 0 0x1000>;
+			reg-names = "mdss";
+
+			interconnects = <&gem_noc MASTER_AMPSS_M0 &config_noc SLAVE_DISPLAY_CFG>,
+					<&mmss_noc MASTER_MDP_PORT0 &mc_virt SLAVE_EBI_CH0>,
+					<&mmss_noc MASTER_MDP_PORT1 &mc_virt SLAVE_EBI_CH0>;
+			interconnect-names = "notused", "mdp0-mem", "mdp1-mem";
+
+			power-domains = <&dispcc MDSS_GDSC>;
+
+			clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+				 <&gcc GCC_DISP_HF_AXI_CLK>,
+				 <&gcc GCC_DISP_SF_AXI_CLK>,
+				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
+			clock-names = "iface", "bus", "nrt_bus", "core";
+
+			assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>;
+			assigned-clock-rates = <460000000>;
+
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			iommus = <&apps_smmu 0x820 0x402>;
+
+			status = "disabled";
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			mdss_mdp: mdp@ae01000 {
+				compatible = "qcom,sdm845-dpu";
+				reg = <0 0x0ae01000 0 0x8f000>,
+				      <0 0x0aeb0000 0 0x2008>;
+				reg-names = "mdp", "vbif";
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&gcc GCC_DISP_HF_AXI_CLK>,
+					 <&dispcc DISP_CC_MDSS_MDP_CLK>,
+					 <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+				clock-names = "iface", "bus", "core", "vsync";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>,
+						  <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+				assigned-clock-rates = <460000000>,
+						       <19200000>;
+
+				operating-points-v2 = <&mdp_opp_table>;
+				power-domains = <&rpmhpd SM8250_MMCX>;
+
+				interrupt-parent = <&mdss>;
+				interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dpu_intf1_out: endpoint {
+							remote-endpoint = <&dsi0_in>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dpu_intf2_out: endpoint {
+							remote-endpoint = <&dsi1_in>;
+						};
+					};
+				};
+
+				mdp_opp_table: mdp-opp-table {
+					compatible = "operating-points-v2";
+
+					opp-200000000 {
+						opp-hz = /bits/ 64 <200000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-300000000 {
+						opp-hz = /bits/ 64 <300000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-345000000 {
+						opp-hz = /bits/ 64 <345000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-460000000 {
+						opp-hz = /bits/ 64 <460000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+			};
+
+			dsi0: dsi@ae94000 {
+				compatible = "qcom,mdss-dsi-ctrl";
+				reg = <0 0x0ae94000 0 0x400>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+					 <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+					 <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					<&gcc GCC_DISP_HF_AXI_CLK>;
+				clock-names = "byte",
+					      "byte_intf",
+					      "pixel",
+					      "core",
+					      "iface",
+					      "bus";
+
+				operating-points-v2 = <&dsi_opp_table>;
+				power-domains = <&rpmhpd SM8250_MMCX>;
+
+				phys = <&dsi0_phy>;
+				phy-names = "dsi";
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dsi0_in: endpoint {
+							remote-endpoint = <&dpu_intf1_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dsi0_out: endpoint {
+						};
+					};
+				};
+			};
+
+			dsi0_phy: dsi-phy@ae94400 {
+				compatible = "qcom,dsi-phy-7nm";
+				reg = <0 0x0ae94400 0 0x200>,
+				      <0 0x0ae94600 0 0x280>,
+				      <0 0x0ae94900 0 0x260>;
+				reg-names = "dsi_phy",
+					    "dsi_phy_lane",
+					    "dsi_pll";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&rpmhcc RPMH_CXO_CLK>;
+				clock-names = "iface", "ref";
+
+				status = "disabled";
+			};
+
+			dsi1: dsi@ae96000 {
+				compatible = "qcom,mdss-dsi-ctrl";
+				reg = <0 0x0ae96000 0 0x400>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
+					 <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
+					 <&dispcc DISP_CC_MDSS_ESC1_CLK>,
+					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&gcc GCC_DISP_HF_AXI_CLK>;
+				clock-names = "byte",
+					      "byte_intf",
+					      "pixel",
+					      "core",
+					      "iface",
+					      "bus";
+
+				operating-points-v2 = <&dsi_opp_table>;
+				power-domains = <&rpmhpd SM8250_MMCX>;
+
+				phys = <&dsi1_phy>;
+				phy-names = "dsi";
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dsi1_in: endpoint {
+							remote-endpoint = <&dpu_intf2_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dsi1_out: endpoint {
+						};
+					};
+				};
+			};
+
+			dsi1_phy: dsi-phy@ae96400 {
+				compatible = "qcom,dsi-phy-7nm";
+				reg = <0 0x0ae96400 0 0x200>,
+				      <0 0x0ae96600 0 0x280>,
+				      <0 0x0ae96900 0 0x260>;
+				reg-names = "dsi_phy",
+					    "dsi_phy_lane",
+					    "dsi_pll";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&rpmhcc RPMH_CXO_CLK>;
+				clock-names = "iface", "ref";
+
+				status = "disabled";
+
+				dsi_opp_table: dsi-opp-table {
+					compatible = "operating-points-v2";
+
+					opp-187500000 {
+						opp-hz = /bits/ 64 <187500000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-300000000 {
+						opp-hz = /bits/ 64 <300000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-358000000 {
+						opp-hz = /bits/ 64 <358000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+				};
+			};
+		};
+
+		dispcc: clock-controller@af00000 {
+			compatible = "qcom,sm8250-dispcc";
+			reg = <0 0x0af00000 0 0x20000>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+				 <&dsi0_phy 0>,
+				 <&dsi0_phy 1>,
+				 <&dsi1_phy 0>,
+				 <&dsi1_phy 1>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <&sleep_clk>;
+			clock-names = "bi_tcxo",
+				      "dsi0_phy_pll_out_byteclk",
+				      "dsi0_phy_pll_out_dsiclk",
+				      "dsi1_phy_pll_out_byteclk",
+				      "dsi1_phy_pll_out_dsiclk",
+				      "dp_link_clk_divsel_ten",
+				      "dp_vco_divided_clk_src_mux",
+				      "dptx1_phy_pll_link_clk",
+				      "dptx1_phy_pll_vco_div_clk",
+				      "dptx2_phy_pll_link_clk",
+				      "dptx2_phy_pll_vco_div_clk",
+				      "edp_phy_pll_link_clk",
+				      "edp_phy_pll_vco_div_clk",
+				      "sleep_clk";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+		};
+
 		pdc: interrupt-controller@b220000 {
 			compatible = "qcom,sm8250-pdc", "qcom,pdc";
 			reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>;
-- 
2.29.2

Re: [PATCH v2 1/7] arm64: dts: qcom: sm8250.dtsi: add display system nodes

[patchwork-bot+linux-arm-msm]

Hello:

This series was applied to qcom/linux.git (refs/heads/for-next):

On Thu,  3 Dec 2020 17:20:59 +0300 you wrote:
> Add device tree nodes for mdss, mdp, dsi0/1.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/sm8250.dtsi | 302 ++++++++++++++++++++++++++-
>  1 file changed, 295 insertions(+), 7 deletions(-)

Here is the summary with links:
  - [v2,1/7] arm64: dts: qcom: sm8250.dtsi: add display system nodes
    https://git.kernel.org/qcom/c/7c1dffd471b1
  - [v2,2/7] arm64: dts: qrb5165-rb5: add mdss/mdp/dsi nodes
    https://git.kernel.org/qcom/c/46967bb61a20
  - [v2,3/7] arm64: dts: qcom: qrb5165-rb5: add gpu/zap-shader node
    https://git.kernel.org/qcom/c/0b2033dcf4af
  - [v2,4/7] arm64: dts: qcom: sm8250-mtp: add gpu/zap-shader node
    https://git.kernel.org/qcom/c/9e301a547a7e
  - [v2,5/7] arm64: dts: qcom: qrb5165-rb5: correct vdc_3v3 regulator
    https://git.kernel.org/qcom/c/04c8e3f7e9e9
  - [v2,6/7] arm64: dts: qcom: qrb5165-rb5: add lt9611 HDMI bridge
    https://git.kernel.org/qcom/c/d004c631ea4e
  - [v2,7/7] arm64: dts: qcom: sm8250: power up dispcc on sm8250 by MMCX regulator
    https://git.kernel.org/qcom/c/3f2094dfbe69

You are awesome, thank you!
--
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html

[PATCH v2 2/7] arm64: dts: qrb5165-rb5: add mdss/mdp/dsi nodes

[Dmitry Baryshkov]

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 32 ++++++++++++++++++++++++
 1 file changed, 32 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
index ce22d4fa383e..ce9d98e2d856 100644
--- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
+++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
@@ -406,6 +406,30 @@ vreg_s8c_1p3: smps8 {
 	};
 };
 
+&dsi0 {
+	status = "okay";
+	vdda-supply = <&vreg_l9a_1p2>;
+
+#if 0
+	qcom,dual-dsi-mode;
+	qcom,master-dsi;
+#endif
+
+	ports {
+		port@1 {
+			endpoint {
+				//remote-endpoint = <&lt9611_a>;
+				data-lanes = <0 1 2 3>;
+			};
+		};
+	};
+};
+
+&dsi0_phy {
+	status = "okay";
+	vdds-supply = <&vreg_l5a_0p88>;
+};
+
 /* LS-I2C0 */
 &i2c4 {
 	status = "okay";
@@ -420,6 +444,14 @@ &i2c15 {
 	status = "okay";
 };
 
+&mdss {
+	status = "okay";
+};
+
+&mdss_mdp {
+	status = "okay";
+};
+
 &pm8150_gpios {
 	gpio-reserved-ranges = <1 1>, <3 2>, <7 1>;
 	gpio-line-names =
-- 
2.29.2

[PATCH v2 3/7] arm64: dts: qcom: qrb5165-rb5: add gpu/zap-shader node

[Dmitry Baryshkov]

Add firmware configuration for Adreno zap shader on qrb5165-rb5.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
index ce9d98e2d856..22c1953f4e63 100644
--- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
+++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
@@ -430,6 +430,13 @@ &dsi0_phy {
 	vdds-supply = <&vreg_l5a_0p88>;
 };
 
+&gpu {
+	zap-shader {
+		memory-region = <&gpu_mem>;
+		firmware-name = "qcom/sm8250/a650_zap.mbn";
+	};
+};
+
 /* LS-I2C0 */
 &i2c4 {
 	status = "okay";
-- 
2.29.2

[PATCH v2 4/7] arm64: dts: qcom: sm8250-mtp: add gpu/zap-shader node

[Dmitry Baryshkov]

Add firmware configuration for Adreno zap shader on sm8250-mtp.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8250-mtp.dts | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
index dea00f19711d..865b6b587843 100644
--- a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
@@ -358,6 +358,13 @@ &cdsp {
 	firmware-name = "qcom/sm8250/cdsp.mbn";
 };
 
+&gpu {
+	zap-shader {
+		memory-region = <&gpu_mem>;
+		firmware-name = "qcom/sm8250/a650_zap.mbn";
+	};
+};
+
 &i2c1 {
 	status = "okay";
 	clock-frequency = <1000000>;
-- 
2.29.2

[PATCH v2 5/7] arm64: dts: qcom: qrb5165-rb5: correct vdc_3v3 regulator

[Dmitry Baryshkov]

vdc_3v3 regulator is sourced from 12V, but it is controlled by l11c
regulator, so set it as vin for vdc_3v3.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
index 22c1953f4e63..94d95dff48c4 100644
--- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
+++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
@@ -87,7 +87,7 @@ vbat_som: vbat-som-regulator {
 	vdc_3v3: vdc-3v3-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "VDC_3V3";
-		vin-supply = <&dc12v>;
+		vin-supply = <&vreg_l11c_3p3>;
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		regulator-always-on;
-- 
2.29.2

[PATCH v2 6/7] arm64: dts: qcom: qrb5165-rb5: add lt9611 HDMI bridge

[Dmitry Baryshkov]

Add device tree node for the lontium lt9611ux DSI-HDMI bridge.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 97 +++++++++++++++++++++++-
 1 file changed, 96 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
index 94d95dff48c4..1ade62d98f98 100644
--- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
+++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
@@ -40,6 +40,17 @@ dc12v: dc12v-regulator {
 		regulator-always-on;
 	};
 
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&lt9611_out>;
+			};
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 
@@ -66,6 +77,26 @@ bt {
 
 	};
 
+	lt9611_1v2: lt9611-vdd12-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "LT9611_1V2";
+
+		vin-supply = <&vdc_3v3>;
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+	};
+
+	lt9611_3v3: lt9611-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "LT9611_3V3";
+
+		vin-supply = <&vdc_3v3>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
 	vbat: vbat-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "VBAT";
@@ -418,7 +449,7 @@ &dsi0 {
 	ports {
 		port@1 {
 			endpoint {
-				//remote-endpoint = <&lt9611_a>;
+				remote-endpoint = <&lt9611_a>;
 				data-lanes = <0 1 2 3>;
 			};
 		};
@@ -444,6 +475,55 @@ &i2c4 {
 
 &i2c5 {
 	status = "okay";
+	clock-frequency = <400000>;
+
+	lt9611_codec: hdmi-bridge@2b {
+		compatible = "lontium,lt9611uxc";
+		reg = <0x2b>;
+		#sound-dai-cells = <1>;
+
+		interrupts-extended = <&tlmm 63 IRQ_TYPE_EDGE_FALLING>;
+
+		reset-gpios = <&pm8150l_gpios 5 GPIO_ACTIVE_HIGH>;
+
+		vdd-supply = <&lt9611_1v2>;
+		vcc-supply = <&lt9611_3v3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lt9611_irq_pin &lt9611_rst_pin>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lt9611_a: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+
+#if 0
+			port@1 {
+				reg = <1>;
+
+				lt9611_b: endpoint {
+					remote-endpoint = <&dsi1_out>;
+				};
+			};
+#endif
+
+			port@2 {
+				reg = <2>;
+
+				lt9611_out: endpoint {
+					remote-endpoint = <&hdmi_con>;
+				};
+			};
+
+		};
+	};
 };
 
 /* LS-I2C1 */
@@ -504,6 +584,15 @@ &pm8150l_gpios {
 		"PM_GPIO-B",
 		"NC",
 		"PM3003A_MODE";
+
+	lt9611_rst_pin: lt9611-rst-pin {
+		pins = "gpio5";
+		function = "normal";
+
+		output-high;
+		input-disable;
+		power-source = <0>;
+	};
 };
 
 &pm8150_rtc {
@@ -735,6 +824,12 @@ &tlmm {
 		"HST_WLAN_UART_TX",
 		"HST_WLAN_UART_RX";
 
+	lt9611_irq_pin: lt9611-irq {
+		pins = "gpio63";
+		function = "gpio";
+		bias-disable;
+	};
+
 	sdc2_default_state: sdc2-default {
 		clk {
 			pins = "sdc2_clk";
-- 
2.29.2

[PATCH v2 7/7] arm64: dts: qcom: sm8250: power up dispcc on sm8250 by MMCX regulator

[Dmitry Baryshkov]

Add regulator controlling MMCX power domain to be used by display clock
controller on SM8250.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8250.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
index f4cae2b82e2a..0c7986bf60d9 100644
--- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -216,6 +216,13 @@ memory@80000000 {
 		reg = <0x0 0x80000000 0x0 0x0>;
 	};
 
+	mmcx_reg: mmcx-reg {
+		compatible = "regulator-fixed-domain";
+		power-domains = <&rpmhpd SM8250_MMCX>;
+		required-opps = <&rpmhpd_opp_low_svs>;
+		regulator-name = "MMCX";
+	};
+
 	pmu {
 		compatible = "arm,armv8-pmuv3";
 		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
@@ -2058,6 +2065,7 @@ opp-358000000 {
 		dispcc: clock-controller@af00000 {
 			compatible = "qcom,sm8250-dispcc";
 			reg = <0 0x0af00000 0 0x20000>;
+			mmcx-supply = <&mmcx_reg>;
 			clocks = <&rpmhcc RPMH_CXO_CLK>,
 				 <&dsi0_phy 0>,
 				 <&dsi0_phy 1>,
-- 
2.29.2