[PATCH AUTOSEL 5.18 07/49] arm64: dts: qcom: msm8994: Fix the cont_splash_mem address

[PATCH AUTOSEL 5.18 07/49] arm64: dts: qcom: msm8994: Fix the cont_splash_mem address

[Sasha Levin]

From: Konrad Dybcio <konrad.dybcio@somainline.org>

[ Upstream commit 049c46f31a726bf8d202ff1681661513447fac84 ]

The default memory map places cont_splash_mem at 3401000, which was
overlooked.. Fix it!

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220319174645.340379-9-konrad.dybcio@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/qcom/msm8994.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/msm8994.dtsi b/arch/arm64/boot/dts/qcom/msm8994.dtsi
index 8c1dc5155b71..c65618b95ce0 100644
--- a/arch/arm64/boot/dts/qcom/msm8994.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8994.dtsi
@@ -183,8 +183,8 @@ dfps_data_mem: dfps_data_mem@3400000 {
 			no-map;
 		};
 
-		cont_splash_mem: memory@3800000 {
-			reg = <0 0x03800000 0 0x2400000>;
+		cont_splash_mem: memory@3401000 {
+			reg = <0 0x03401000 0 0x2200000>;
 			no-map;
 		};
 
-- 
2.35.1

[PATCH AUTOSEL 5.18 08/49] arm64: dts: qcom: msm8994: Fix BLSP[12]_DMA channels count

[Sasha Levin]

From: Konrad Dybcio <konrad.dybcio@somainline.org>

[ Upstream commit 1ae438d26b620979ed004d559c304d31c42173ae ]

MSM8994 actually features 24 DMA channels for each BLSP,
fix it!

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220319174645.340379-14-konrad.dybcio@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/qcom/msm8994.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/msm8994.dtsi b/arch/arm64/boot/dts/qcom/msm8994.dtsi
index c65618b95ce0..b1e595cb4b90 100644
--- a/arch/arm64/boot/dts/qcom/msm8994.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8994.dtsi
@@ -498,7 +498,7 @@ blsp1_dma: dma-controller@f9904000 {
 			#dma-cells = <1>;
 			qcom,ee = <0>;
 			qcom,controlled-remotely;
-			num-channels = <18>;
+			num-channels = <24>;
 			qcom,num-ees = <4>;
 		};
 
@@ -634,7 +634,7 @@ blsp2_dma: dma-controller@f9944000 {
 			#dma-cells = <1>;
 			qcom,ee = <0>;
 			qcom,controlled-remotely;
-			num-channels = <18>;
+			num-channels = <24>;
 			qcom,num-ees = <4>;
 		};
 
-- 
2.35.1

[PATCH AUTOSEL 5.18 14/49] arm64: dts: qcom: sdm845-xiaomi-beryllium: fix typo in panel's vddio-supply property

[Sasha Levin]

From: Joel Selvaraj <jo@jsfamily.in>

[ Upstream commit 1f1c494082a1f10d03ce4ee1485ee96d212e22ff ]

vddio is misspelled with a "0" instead of "o". Fix it.

Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
Reviewed-by: Caleb Connolly <caleb@connolly.tech>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/BY5PR02MB7009901651E6A8D5ACB0425ED91F9@BY5PR02MB7009.namprd02.prod.outlook.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
index 367389526b41..a97f5e89e1d0 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
@@ -218,7 +218,7 @@ &dsi0 {
 	panel@0 {
 		compatible = "tianma,fhd-video";
 		reg = <0>;
-		vddi0-supply = <&vreg_l14a_1p8>;
+		vddio-supply = <&vreg_l14a_1p8>;
 		vddpos-supply = <&lab>;
 		vddneg-supply = <&ibb>;
 
-- 
2.35.1

[PATCH AUTOSEL 5.18 25/49] arm64: dts: qcom: sc7280-idp: Configure CTS pin to bias-bus-hold for bluetooth

[Sasha Levin]

From: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>

[ Upstream commit 497b272759986af1aa5a25b5e903d082c67bd8f6 ]

WLAN rail was leaking power during RBSC/sleep even after turning BT off.
Change active and sleep pinctrl configurations to handle same.

Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1650556567-4995-2-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 18 ++++++++++++------
 1 file changed, 12 insertions(+), 6 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index ecbf2b89d896..5ab3696af354 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -400,10 +400,13 @@ &qup_uart5_rx {
 
 &qup_uart7_cts {
 	/*
-	 * Configure a pull-down on CTS to match the pull of
-	 * the Bluetooth module.
+	 * Configure a bias-bus-hold on CTS to lower power
+	 * usage when Bluetooth is turned off. Bus hold will
+	 * maintain a low power state regardless of whether
+	 * the Bluetooth module drives the pin in either
+	 * direction or leaves the pin fully unpowered.
 	 */
-	bias-pull-down;
+	bias-bus-hold;
 };
 
 &qup_uart7_rts {
@@ -495,10 +498,13 @@ qup_uart7_sleep_cts: qup-uart7-sleep-cts {
 		pins = "gpio28";
 		function = "gpio";
 		/*
-		 * Configure a pull-down on CTS to match the pull of
-		 * the Bluetooth module.
+		 * Configure a bias-bus-hold on CTS to lower power
+		 * usage when Bluetooth is turned off. Bus hold will
+		 * maintain a low power state regardless of whether
+		 * the Bluetooth module drives the pin in either
+		 * direction or leaves the pin fully unpowered.
 		 */
-		bias-pull-down;
+		bias-bus-hold;
 	};
 
 	qup_uart7_sleep_rts: qup-uart7-sleep-rts {
-- 
2.35.1

[PATCH AUTOSEL 5.18 26/49] arm64: dts: qcom: sc7280-qcard: Configure CTS pin to bias-bus-hold for bluetooth

[Sasha Levin]

From: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>

[ Upstream commit 3d0e375bae55c2dfa6dd0762f45ad71f0b192f71 ]

WLAN rail was leaking power during RBSC/sleep even after turning BT off.
Change active and sleep pinctrl configurations to handle same.

Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1650556567-4995-3-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi | 19 ++++++++++++++-----
 1 file changed, 14 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi b/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi
index b833ba1e8f4a..98b5cd70bca5 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi
@@ -398,8 +398,14 @@ &qup_i2c13_data_clk {
 
 /* For mos_bt_uart */
 &qup_uart7_cts {
-	/* Configure a pull-down on CTS to match the pull of the Bluetooth module. */
-	bias-pull-down;
+	/*
+	 * Configure a bias-bus-hold on CTS to lower power
+	 * usage when Bluetooth is turned off. Bus hold will
+	 * maintain a low power state regardless of whether
+	 * the Bluetooth module drives the pin in either
+	 * direction or leaves the pin fully unpowered.
+	 */
+	bias-bus-hold;
 };
 
 /* For mos_bt_uart */
@@ -490,10 +496,13 @@ qup_uart7_sleep_cts: qup-uart7-sleep-cts {
 		pins = "gpio28";
 		function = "gpio";
 		/*
-		 * Configure a pull-down on CTS to match the pull of
-		 * the Bluetooth module.
+		 * Configure a bias-bus-hold on CTS to lower power
+		 * usage when Bluetooth is turned off. Bus hold will
+		 * maintain a low power state regardless of whether
+		 * the Bluetooth module drives the pin in either
+		 * direction or leaves the pin fully unpowered.
 		 */
-		bias-pull-down;
+		bias-bus-hold;
 	};
 
 	/* For mos_bt_uart */
-- 
2.35.1